4 The following is a consolidated list of the kernel parameters as implemented
5 (mostly) by the __setup() macro and sorted into English Dictionary order
6 (defined as ignoring all punctuation and sorting digits before letters in a
7 case insensitive manner), and with descriptions where known.
9 Module parameters for loadable modules are specified only as the
10 parameter name with optional '=' and value as appropriate, such as:
12 modprobe usbcore blinkenlights=1
14 Module parameters for modules that are built into the kernel image
15 are specified on the kernel command line with the module name plus
16 '.' plus parameter name, with '=' and value if appropriate, such as:
18 usbcore.blinkenlights=1
20 This document may not be entirely up to date and comprehensive. The command
21 "modinfo -p ${modulename}" shows a current list of all parameters of a loadable
22 module. Loadable modules, after being loaded into the running kernel, also
23 reveal their parameters in /sys/module/${modulename}/parameters/. Some of these
24 parameters may be changed at runtime by the command
25 "echo -n ${value} > /sys/module/${modulename}/parameters/${parm}".
27 The parameters listed below are only valid if certain kernel build options were
28 enabled and if respective hardware is present. The text in square brackets at
29 the beginning of each description states the restrictions within which a
30 parameter is applicable:
32 ACPI ACPI support is enabled.
33 AGP AGP (Accelerated Graphics Port) is enabled.
34 ALSA ALSA sound support is enabled.
35 APIC APIC support is enabled.
36 APM Advanced Power Management support is enabled.
37 AVR32 AVR32 architecture is enabled.
38 AX25 Appropriate AX.25 support is enabled.
39 BLACKFIN Blackfin architecture is enabled.
40 DRM Direct Rendering Management support is enabled.
41 EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
42 EFI EFI Partitioning (GPT) is enabled
43 EIDE EIDE/ATAPI support is enabled.
44 FB The frame buffer device is enabled.
45 HW Appropriate hardware is enabled.
46 IA-64 IA-64 architecture is enabled.
47 IMA Integrity measurement architecture is enabled.
48 IOSCHED More than one I/O scheduler is enabled.
49 IP_PNP IP DHCP, BOOTP, or RARP is enabled.
50 ISAPNP ISA PnP code is enabled.
51 ISDN Appropriate ISDN support is enabled.
52 JOY Appropriate joystick support is enabled.
53 LIBATA Libata driver is enabled
54 LP Printer support is enabled.
55 LOOP Loopback device support is enabled.
56 M68k M68k architecture is enabled.
57 These options have more detailed description inside of
58 Documentation/m68k/kernel-options.txt.
59 MCA MCA bus support is enabled.
60 MDA MDA console support is enabled.
61 MOUSE Appropriate mouse support is enabled.
62 MSI Message Signaled Interrupts (PCI).
63 MTD MTD (Memory Technology Device) support is enabled.
64 NET Appropriate network support is enabled.
65 NUMA NUMA support is enabled.
66 GENERIC_TIME The generic timeofday code is enabled.
67 NFS Appropriate NFS support is enabled.
68 OSS OSS sound support is enabled.
69 PV_OPS A paravirtualized kernel is enabled.
70 PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
71 PARISC The PA-RISC architecture is enabled.
72 PCI PCI bus support is enabled.
73 PCIE PCI Express support is enabled.
74 PCMCIA The PCMCIA subsystem is enabled.
75 PNP Plug & Play support is enabled.
76 PPC PowerPC architecture is enabled.
77 PPT Parallel port support is enabled.
78 PS2 Appropriate PS/2 support is enabled.
79 RAM RAM disk support is enabled.
80 ROOTPLUG The example Root Plug LSM is enabled.
81 S390 S390 architecture is enabled.
82 SCSI Appropriate SCSI support is enabled.
83 A lot of drivers has their options described inside of
85 SECURITY Different security models are enabled.
86 SELINUX SELinux support is enabled.
87 SERIAL Serial support is enabled.
88 SH SuperH architecture is enabled.
89 SMP The kernel is an SMP kernel.
90 SPARC Sparc architecture is enabled.
91 SWSUSP Software suspend (hibernation) is enabled.
92 SUSPEND System suspend states are enabled.
93 FTRACE Function tracing enabled.
94 TS Appropriate touchscreen support is enabled.
95 UMS USB Mass Storage support is enabled.
96 USB USB support is enabled.
97 USBHID USB Human Interface Device support is enabled.
98 V4L Video For Linux support is enabled.
99 VGA The VGA console has been enabled.
100 VT Virtual terminal support is enabled.
101 WDT Watchdog support is enabled.
102 XT IBM PC/XT MFM hard disk support is enabled.
103 X86-32 X86-32, aka i386 architecture is enabled.
104 X86-64 X86-64 architecture is enabled.
105 More X86-64 boot options can be found in
106 Documentation/x86/x86_64/boot-options.txt .
107 X86 Either 32bit or 64bit x86 (same as X86-32+X86-64)
109 In addition, the following text indicates that the option:
111 BUGS= Relates to possible processor bugs on the said processor.
112 KNL Is a kernel start-up parameter.
113 BOOT Is a boot loader parameter.
115 Parameters denoted with BOOT are actually interpreted by the boot
116 loader, and have no meaning to the kernel directly.
117 Do not modify the syntax of boot loader parameters without extreme
118 need or coordination with <Documentation/x86/boot.txt>.
120 There are also arch-specific kernel-parameters not documented here.
121 See for example <Documentation/x86/x86_64/boot-options.txt>.
123 Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
124 a trailing = on the name of any parameter states that that parameter will
125 be entered as an environment variable, whereas its absence indicates that
126 it will appear as a kernel argument readable via /proc/cmdline by programs
127 running once the system is up.
129 The number of kernel parameters is not limited, but the length of the
130 complete command line (parameters including spaces etc.) is limited to
131 a fixed number of characters. This limit depends on the architecture
132 and is between 256 and 4096 characters. It is defined in the file
133 ./include/asm/setup.h as COMMAND_LINE_SIZE.
136 acpi= [HW,ACPI,X86-64,i386]
137 Advanced Configuration and Power Interface
138 Format: { force | off | ht | strict | noirq | rsdt }
139 force -- enable ACPI if default was off
140 off -- disable ACPI if default was on
141 noirq -- do not use ACPI for IRQ routing
142 ht -- run only enough ACPI to enable Hyper Threading
143 strict -- Be less tolerant of platforms that are not
144 strictly ACPI specification compliant.
145 rsdt -- prefer RSDT over (default) XSDT
147 See also Documentation/power/pm.txt, pci=noacpi
149 acpi_apic_instance= [ACPI, IOAPIC]
151 2: use 2nd APIC table, if available
152 1,0: use 1st APIC table
155 acpi_sleep= [HW,ACPI] Sleep options
156 Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
157 old_ordering, s4_nonvs }
158 See Documentation/power/video.txt for information on
160 s3_beep is for debugging; it makes the PC's speaker beep
161 as soon as the kernel's real-mode entry point is called.
162 s4_nohwsig prevents ACPI hardware signature from being
163 used during resume from hibernation.
164 old_ordering causes the ACPI 1.0 ordering of the _PTS
165 control method, with respect to putting devices into
166 low power states, to be enforced (the ACPI 2.0 ordering
167 of _PTS is used by default).
168 s4_nonvs prevents the kernel from saving/restoring the
169 ACPI NVS memory during hibernation.
171 acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
172 Format: { level | edge | high | low }
174 acpi_irq_balance [HW,ACPI]
175 ACPI will balance active IRQs
178 acpi_irq_nobalance [HW,ACPI]
179 ACPI will not move active IRQs (default)
182 acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for
184 Format: <irq>,<irq>...
186 acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA
187 Format: <irq>,<irq>...
189 acpi_no_auto_ssdt [HW,ACPI] Disable automatic loading of SSDT
191 acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS
192 Format: To spoof as Windows 98: ="Microsoft Windows"
194 acpi_osi= [HW,ACPI] Modify list of supported OS interface strings
195 acpi_osi="string1" # add string1 -- only one string
196 acpi_osi="!string2" # remove built-in string2
197 acpi_osi= # disable all strings
199 acpi_serialize [HW,ACPI] force serialization of AML methods
201 acpi_skip_timer_override [HW,ACPI]
202 Recognize and ignore IRQ0/pin2 Interrupt Override.
203 For broken nForce2 BIOS resulting in XT-PIC timer.
204 acpi_use_timer_override [HW,ACPI]
205 Use timer override. For some broken Nvidia NF5 boards
206 that require a timer override, but don't have
209 acpi_backlight= [HW,ACPI]
210 acpi_backlight=vendor
212 If set to vendor, prefer vendor specific driver
213 (e.g. thinkpad_acpi, sony_acpi, etc.) instead
214 of the ACPI video.ko driver.
216 acpi_display_output= [HW,ACPI]
217 acpi_display_output=vendor
218 acpi_display_output=video
221 acpi.debug_layer= [HW,ACPI,ACPI_DEBUG]
222 acpi.debug_level= [HW,ACPI,ACPI_DEBUG]
224 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
225 debug output. Bits in debug_layer correspond to a
226 _COMPONENT in an ACPI source file, e.g.,
227 #define _COMPONENT ACPI_PCI_COMPONENT
228 Bits in debug_level correspond to a level in
229 ACPI_DEBUG_PRINT statements, e.g.,
230 ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
231 The debug_level mask defaults to "info". See
232 Documentation/acpi/debug.txt for more information about
233 debug layers and levels.
235 Enable processor driver info messages:
236 acpi.debug_layer=0x20000000
237 Enable PCI/PCI interrupt routing info messages:
238 acpi.debug_layer=0x400000
239 Enable AML "Debug" output, i.e., stores to the Debug
240 object while interpreting AML:
241 acpi.debug_layer=0xffffffff acpi.debug_level=0x2
242 Enable all messages related to ACPI hardware:
243 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
245 Some values produce so much output that the system is
246 unusable. The "log_buf_len" parameter may be useful
247 if you need to capture more output.
249 acpi.power_nocheck= [HW,ACPI]
250 Format: 1/0 enable/disable the check of power state.
251 On some bogus BIOS the _PSC object/_STA object of
252 power resource can't return the correct device power
253 state. In such case it is unneccessary to check its
254 power state again in power transition.
255 1 : disable the power state check
257 acpi_pm_good [X86-32,X86-64]
258 Override the pmtimer bug detection: force the kernel
259 to assume that this machine's pmtimer latches its value
260 and always returns good values.
263 { off | try_unsupported }
264 off: disable AGP support
265 try_unsupported: try to drive unsupported chipsets
266 (may crash computer or cause data corruption)
268 enable_timer_pin_1 [i386,x86-64]
269 Enable PIN 1 of APIC timer
270 Can be useful to work around chipset bugs
271 (in particular on some ATI chipsets).
272 The kernel tries to set a reasonable default.
274 disable_timer_pin_1 [i386,x86-64]
275 Disable PIN 1 of APIC timer
276 Can be useful to work around chipset bugs.
279 Format: <io>,<irq>,<dma>,<dma2>,<type>
282 See header of drivers/scsi/advansys.c.
284 advwdt= [HW,WDT] Advantech WDT
285 Format: <iostart>,<iostop>
287 aedsp16= [HW,OSS] Audio Excel DSP 16
288 Format: <io>,<irq>,<dma>,<mss_io>,<mpu_io>,<mpu_irq>
289 See also header of sound/oss/aedsp16.c.
292 See Documentation/scsi/aha152x.txt.
295 Format: <portbase>[,<buson>,<busoff>[,<dmaspeed>]]
298 See Documentation/scsi/aic7xxx.txt.
301 See Documentation/scsi/aic79xx.txt.
303 amd_iommu= [HW,X86-84]
304 Pass parameters to the AMD IOMMU driver in the system.
306 isolate - enable device isolation (each device, as far
307 as possible, will get its own protection
309 share - put every device behind one IOMMU into the
310 same protection domain
311 fullflush - enable flushing of IO/TLB entries when
312 they are unmapped. Otherwise they are
313 flushed before they will be reused, which
316 amd_iommu_size= [HW,X86-64]
317 Define the size of the aperture for the AMD IOMMU
318 driver. Possible values are:
319 '32M', '64M' (default), '128M', '256M', '512M', '1G'
321 amijoy.map= [HW,JOY] Amiga joystick support
322 Map of devices attached to JOY0DAT and JOY1DAT
324 See also Documentation/kernel/input/joystick.txt
326 analog.map= [HW,JOY] Analog joystick and gamepad support
327 Specifies type or capabilities of an analog joystick
328 connected to one of 16 gameports
329 Format: <type1>,<type2>,..<type16>
332 Power management functions (SPARCstation-4/5 + deriv.)
334 Disable APC CPU standby support. SPARCstation-Fox does
335 not play well with APC CPU idle - disable it if you have
336 APC and your system crashes randomly.
338 apic= [APIC,i386] Advanced Programmable Interrupt Controller
339 Change the output verbosity whilst booting
340 Format: { quiet (default) | verbose | debug }
341 Change the amount of debugging information output
342 when initialising the APIC and IO-APIC components.
344 apm= [APM] Advanced Power Management
345 See header of arch/x86/kernel/apm_32.c.
347 arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
348 Format: <io>,<irq>,<nodeID>
352 atarimouse= [HW,MOUSE] Atari Mouse
354 atascsi= [HW,SCSI] Atari SCSI
356 atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess,
357 EzKey and similar keyboards
359 atkbd.reset= [HW] Reset keyboard during initialization
361 atkbd.set= [HW] Select keyboard code set
362 Format: <int> (2 = AT (default), 3 = PS/2)
364 atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar
367 atkbd.softraw= [HW] Choose between synthetic and real raw mode
368 Format: <bool> (0 = real, 1 = synthetic (default))
370 atkbd.softrepeat= [HW]
371 Use software keyboard repeat
375 baycom_epp= [HW,AX25]
378 baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem
380 See header of drivers/net/hamradio/baycom_par.c.
382 baycom_ser_fdx= [HW,AX25]
383 BayCom Serial Port AX.25 Modem (Full Duplex Mode)
384 Format: <io>,<irq>,<mode>[,<baud>]
385 See header of drivers/net/hamradio/baycom_ser_fdx.c.
387 baycom_ser_hdx= [HW,AX25]
388 BayCom Serial Port AX.25 Modem (Half Duplex Mode)
389 Format: <io>,<irq>,<mode>
390 See header of drivers/net/hamradio/baycom_ser_hdx.c.
392 boot_delay= Milliseconds to delay each printk during boot.
393 Values larger than 10 seconds (10000) are changed to
397 bootmem_debug [KNL] Enable bootmem allocator debug messages.
399 bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
400 bttv.radio= Most important insmod options are available as
402 bttv.pll= See Documentation/video4linux/bttv/Insmod-options
403 bttv.tuner= and Documentation/video4linux/bttv/CARDLIST
406 See drivers/scsi/BusLogic.c, comment before function
407 BusLogic_ParseDriverOptions().
409 c101= [NET] Moxa C101 synchronous serial card
411 cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection.
412 Sometimes CPU hardware bugs make them report the cache
413 size incorrectly. The kernel will attempt work arounds
414 to fix known problems, but for some CPUs it is not
415 possible to determine what the correct size should be.
416 This option provides an override for these situations.
418 security= [SECURITY] Choose a security module to enable at boot.
419 If this boot parameter is not specified, only the first
420 security module asking for security registration will be
421 loaded. An invalid security module name will be treated
422 as if no module has been chosen.
425 [SECURITY] Disable capabilities. This would normally
426 be used only if an alternative security model is to be
427 configured. Potentially dangerous and should only be
428 used if you are entirely sure of the consequences.
430 ccw_timeout_log [S390]
431 See Documentation/s390/CommonIO for details.
433 cgroup_disable= [KNL] Disable a particular controller
434 Format: {name of the controller(s) to disable}
435 {Currently supported controllers - "memory"}
437 checkreqprot [SELINUX] Set initial checkreqprot flag value.
438 Format: { "0" | "1" }
439 See security/selinux/Kconfig help text.
440 0 -- check protection applied by kernel (includes
441 any implied execute protection).
442 1 -- check protection requested by application.
443 Default value is set via a kernel config option.
444 Value can be changed at runtime via
445 /selinux/checkreqprot.
448 See Documentation/s390/CommonIO for details.
450 clock= [BUGS=X86-32, HW] gettimeofday clocksource override.
452 Forces specified clocksource (if available) to be used
453 when calculating gettimeofday(). If specified
454 clocksource is not available, it defaults to PIT.
455 Format: { pit | tsc | cyclone | pmtmr }
457 clocksource= [GENERIC_TIME] Override the default clocksource
459 Override the default clocksource and use the clocksource
460 with the name specified.
461 Some clocksource names to choose from, depending on
463 [all] jiffies (this is the base, fallback clocksource)
465 [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2,
466 pxa_timer,timer3,32k_counter,timer0_1
468 [X86-32] pit,hpet,tsc,vmi-timer;
469 scx200_hrt on Geode; cyclone on IBM x440
477 clearcpuid=BITNUM [X86]
478 Disable CPUID feature X for the kernel. See
479 arch/x86/include/asm/cpufeature.h for the valid bit
480 numbers. Note the Linux specific bits are not necessarily
481 stable over kernel options, but the vendor specific
483 Also note that user programs calling CPUID directly
484 or using the feature without checking anything
485 will still see it. This just prevents it from
486 being used by the kernel or shown in /proc/cpuinfo.
487 Also note the kernel might malfunction if you disable
490 code_bytes [IA32/X86_64] How many bytes of object code to print
495 hpet= [X86-32,HPET] option to control HPET usage
496 Format: { enable (default) | disable | force |
498 disable: disable HPET and use PIT instead
499 force: allow force enabled of undocumented chips (ICH4,
501 verbose: show contents of HPET registers during setup
503 com20020= [HW,NET] ARCnet - COM20020 chipset
505 <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
507 com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
511 ARCnet - COM90xx chipset (memory-mapped buffers)
512 Format: <io>[,<irq>[,<memstart>]]
514 condev= [HW,S390] console device
517 console= [KNL] Output console device and options.
519 tty<n> Use the virtual console device <n>.
523 Use the specified serial port. The options are of
524 the form "bbbbpnf", where "bbbb" is the baud rate,
525 "p" is parity ("n", "o", or "e"), "n" is number of
526 bits, and "f" is flow control ("r" for RTS or
527 omit it). Default is "9600n8".
529 See Documentation/serial-console.txt for more
531 Documentation/networking/netconsole.txt for an
534 uart[8250],io,<addr>[,options]
535 uart[8250],mmio,<addr>[,options]
536 Start an early, polled-mode console on the 8250/16550
537 UART at the specified I/O port or MMIO address,
538 switching to the matching ttyS device later. The
539 options are the same as for ttyS, above.
541 If the device connected to the port is not a TTY but a braille
542 device, prepend "brl," before the device type, for instance
544 For now, only VisioBraille is supported.
546 earlycon= [KNL] Output early console device and options.
547 uart[8250],io,<addr>[,options]
548 uart[8250],mmio,<addr>[,options]
549 Start an early, polled-mode console on the 8250/16550
550 UART at the specified I/O port or MMIO address.
551 The options are the same as for ttyS, above.
554 [HW] Never suspend the console
555 Disable suspending of consoles during suspend and
556 hibernate operations. Once disabled, debugging
557 messages can reach various consoles while the rest
558 of the system is being put to sleep (ie, while
559 debugging driver suspend/resume hooks). This may
560 not work reliably with all consoles, but is known
561 to work with serial and VGA consoles.
564 [KNL] Change the default value for
565 /proc/<pid>/coredump_filter.
566 See also Documentation/filesystems/proc.txt.
568 cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
570 <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
572 crashkernel=nn[KMG]@ss[KMG]
573 [KNL] Reserve a chunk of physical memory to
574 hold a kernel to switch to with kexec on panic.
576 crashkernel=range1:size1[,range2:size2,...][@offset]
577 [KNL] Same as above, but depends on the memory
578 in the running system. The syntax of range is
579 start-[end] where start and end are both
580 a memory unit (amount[KMG]). See also
581 Documentation/kdump/kdump.txt for a example.
586 cs89x0_media= [HW,NET]
587 Format: { rj45 | aui | bnc }
590 See header of drivers/s390/block/dasd_devmap.c.
592 db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
593 (one device per port)
594 Format: <port#>,<type>
595 See also Documentation/input/joystick-parport.txt
597 debug [KNL] Enable kernel debugging (events log level).
600 [KNL] verbose self-tests
602 Print debugging info while doing the locking API
604 We default to 0 (no extra messages), setting it to
605 1 will print _a lot_ more information - normally
606 only useful to kernel developers.
608 debug_objects [KNL] Enable object debugging
610 debugpat [X86] Enable PAT debugging
612 decnet.addr= [HW,NET]
613 Format: <area>[,<node>]
614 See also Documentation/networking/decnet.txt.
617 Format: <blue0>,<blue1>,<blue2>,...,<blue15>
618 Change the default blue palette of the console.
619 This is a 16-member array composed of values
623 Format: <green0>,<green1>,<green2>,...,<green15>
624 Change the default green palette of the console.
625 This is a 16-member array composed of values
629 Format: <red0>,<red1>,<red2>,...,<red15>
630 Change the default red palette of the console.
631 This is a 16-member array composed of values
637 Set system-wide default UTF-8 mode for all tty's.
638 Default is 1, i.e. UTF-8 mode is enabled for all
639 newly opened terminals.
642 Set number of hash buckets for dentry cache.
645 IO parameters + enable/disable command.
647 digiepca= [HW,SERIAL]
648 See drivers/char/README.epca and
649 Documentation/serial/digiepca.txt.
651 disable_mtrr_cleanup [X86]
652 enable_mtrr_cleanup [X86]
653 The kernel tries to adjust MTRR layout from continuous
654 to discrete, to make X server driver able to add WB
655 entry later. This parameter enables/disables that.
657 mtrr_chunk_size=nn[KMG] [X86]
658 used for mtrr cleanup. It is largest continous chunk
659 that could hold holes aka. UC entries.
661 mtrr_gran_size=nn[KMG] [X86]
662 Used for mtrr cleanup. It is granularity of mtrr block.
664 Large value could prevent small alignment from
667 mtrr_spare_reg_nr=n [X86]
669 Range: 0,7 : spare reg number
671 Used for mtrr cleanup. It is spare mtrr entries number.
672 Set to 2 or more if your graphical card needs more.
674 disable_mtrr_trim [X86, Intel and AMD only]
675 By default the kernel will trim any uncacheable
676 memory out of your available memory pool based on
677 MTRR settings. This parameter disables that behavior,
678 possibly causing your machine to run very slowly.
680 dmasound= [HW,OSS] Sound subsystem buffers
686 earlyprintk= [X86-32,X86-64,SH,BLACKFIN]
688 earlyprintk=serial[,ttySn[,baudrate]]
691 Append ",keep" to not disable it when the real console
694 Only vga or serial or usb debug port at a time.
696 Currently only ttyS0 and ttyS1 are supported.
698 Interaction with the standard serial driver is not
701 The VGA output is eventually overwritten by the real
707 Format: {"off" | "on" | "skip[mbr]"}
709 eisa_irq_edge= [PARISC,HW]
710 See header of drivers/parisc/eisa.c.
713 See comment before function elanfreq_setup() in
714 arch/x86/kernel/cpu/cpufreq/elanfreq.c.
717 Format: {"anticipatory" | "cfq" | "deadline" | "noop"}
718 See Documentation/block/as-iosched.txt and
719 Documentation/block/deadline-iosched.txt for details.
721 elfcorehdr= [IA64,PPC,SH,X86-32,X86_64]
722 Specifies physical address of start of kernel core
723 image elf header. Generally kexec loader will
724 pass this option to capture kernel.
725 See Documentation/kdump/kdump.txt for details.
727 enforcing [SELINUX] Set initial enforcing status.
729 See security/selinux/Kconfig help text.
730 0 -- permissive (log only, no denials).
731 1 -- enforcing (deny and log).
733 Value can be changed at runtime via /selinux/enforce.
735 ether= [HW,NET] Ethernet cards parameters
736 This option is obsoleted by the "netdev=" option, which
737 has equivalent usage. See its documentation for details.
739 eurwdt= [HW,WDT] Eurotech CPU-1220/1410 onboard watchdog.
744 fail_make_request=[KNL]
745 General fault injection mechanism.
746 Format: <interval>,<probability>,<space>,<times>
747 See also /Documentation/fault-injection/.
750 See header of drivers/scsi/fd_mcs.c.
753 See header of drivers/scsi/fdomain.c.
756 See Documentation/blockdev/floppy.txt.
758 force_pal_cache_flush
759 [IA-64] Avoid check_sal_cache_flush which may hang on
760 buggy SAL_CACHE_FLUSH implementations. Using this
761 parameter will force ia64_sal_cache_flush to call
762 ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
765 [ftrace] will set and start the specified tracer
766 as early as possible in order to facilitate early
770 [ftrace] will dump the trace buffers on oops.
773 [HW,JOY] Multisystem joystick and NES/SNES/PSX pad
774 support via parallel port (up to 5 devices per port)
775 Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
776 See also Documentation/input/joystick-parport.txt
780 gart_fix_e820= [X86_64] disable the fix e820 for K8 GART
785 See header of drivers/scsi/gdth.c.
787 gpt [EFI] Forces disk with valid GPT signature but
788 invalid Protective MBR to be treated as GPT.
792 hashdist= [KNL,NUMA] Large hashes allocated during boot
793 are distributed across NUMA nodes. Defaults on
794 for IA-64, off otherwise.
795 Format: 0 | 1 (for off | on)
797 hcl= [IA-64] SGI's Hardware Graph compatibility layer
799 hd= [EIDE] (E)IDE hard drive subsystem geometry
800 Format: <cyl>,<head>,<sect>
802 highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
803 size of <nn>. This works even on boxes that have no
804 highmem otherwise. This also works to reduce highmem
805 size on bigger boxes.
807 highres= [KNL] Enable/disable high resolution timer mode.
808 Valid parameters: "on", "off"
812 See Documentation/isdn/README.HiSax.
814 hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
815 hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
816 On x86-64 and powerpc, this option can be specified
817 multiple times interleaved with hugepages= to reserve
818 huge pages of different sizes. Valid pages sizes on
819 x86-64 are 2M (when the CPU supports "pse") and 1G
820 (when the CPU supports the "pdpe1gb" cpuinfo flag)
821 Note that 1GB pages can only be allocated at boot time
822 using hugepages= and not freed afterwards.
824 [same as hugepagesz=] The size of the default
825 HugeTLB page size. This is the size represented by
826 the legacy /proc/ hugepages APIs, used for SHM, and
827 default size when mounting hugetlbfs filesystems.
828 Defaults to the default architecture's huge page size
833 hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
834 terminal devices. Valid values: 0..8
835 hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
836 If specified, z/VM IUCV HVC accepts connections
837 from listed z/VM user IDs only.
839 i2c_bus= [HW] Override the default board specific I2C bus speed
840 or register an additional I2C bus that is not
841 registered from board initialization code.
845 i8042.debug [HW] Toggle i8042 debug mode
846 i8042.direct [HW] Put keyboard port into non-translated mode
847 i8042.dumbkbd [HW] Pretend that controller can only read data from
848 keyboard and cannot control its state
849 (Don't attempt to blink the leds)
850 i8042.noaux [HW] Don't check for auxiliary (== mouse) port
851 i8042.nokbd [HW] Don't check/create keyboard port
852 i8042.noloop [HW] Disable the AUX Loopback command while probing
854 i8042.nomux [HW] Don't check presence of an active multiplexing
856 i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
859 [HW] Frequency with which keyboard LEDs should blink
860 when kernel panics (default is 0.5 sec)
861 i8042.reset [HW] Reset the controller during init and cleanup
862 i8042.unlock [HW] Unlock (ignore) the keylock
866 i8k.ignore_dmi [HW] Continue probing hardware even if DMI data
867 indicates that the driver is running on unsupported
869 i8k.force [HW] Activate i8k driver even if SMM BIOS signature
870 does not match list of supported models.
872 [HW] Report power status in /proc/i8k
873 (disabled by default)
874 i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN
877 ibmmcascsi= [HW,MCA,SCSI] IBM MicroChannel SCSI adapter
878 See Documentation/mca.txt.
881 Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
883 ide-core.nodma= [HW] (E)IDE subsystem
884 Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
885 .vlb_clock .pci_clock .noflush .noprobe .nowerr .cdrom
886 .chs .ignore_cable are additional options
887 See Documentation/ide/ide.txt.
889 idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
890 See Documentation/ide/ide.txt.
893 Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
894 Poll forces a polling idle loop that can slightly
895 improve the performance of waking up a idle CPU, but
896 will use a lot of power and make the system run hot.
898 idle=mwait: On systems which support MONITOR/MWAIT but
899 the kernel chose to not use it because it doesn't save
900 as much power as a normal idle loop, use the
901 MONITOR/MWAIT idle loop anyways. Performance should be
902 the same as idle=poll.
903 idle=halt: Halt is forced to be used for CPU idle.
904 In such case C2/C3 won't be used again.
905 idle=nomwait: Disable mwait for CPU C-states
907 ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
908 Claim all unknown PCI IDE storage controllers.
910 ignore_loglevel [KNL]
911 Ignore loglevel setting - this will print /all/
912 kernel messages to the console. Useful for debugging.
915 Set number of hash buckets for inode cache.
918 Format: { "0" | "1" }
919 0 -- integrity auditing messages. (Default)
920 1 -- enable informational integrity auditing messages.
923 Formt: { "sha1" | "md5" }
927 See header of drivers/scsi/in2000.c.
931 Run specified binary instead of /sbin/init as init
934 initcall_debug [KNL] Trace initcalls as they are executed. Useful
935 for working out where the kernel is dying during
938 initrd= [BOOT] Specify the location of the initial ramdisk
940 inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
945 iomem= Disable strict checking of access to MMIO memory
946 strict regions from userspace.
962 intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option
964 Enable intel iommu driver.
966 Disable intel iommu driver.
967 igfx_off [Default Off]
968 By default, gfx is mapped as normal device. If a gfx
969 device has a dedicated DMAR unit, the DMAR unit is
970 bypassed by not enabling DMAR with this option. In
971 this case, gfx device will use physical address for
974 With this option iommu will not optimize to look
975 for io virtual address below 32 bit forcing dual
976 address cycle on pci bus for cards supporting greater
977 than 32 bit addressing. The default is to look
978 for translation below 32 bit and if not available
979 then look in the higher range.
981 With this option on every unmap_single operation will
982 result in a hardware IOTLB flush operation as opposed
983 to batching them for performance.
985 io_delay= [X86-32,X86-64] I/O delay method
987 Standard port 0x80 based delay
989 Alternate port 0xed based delay (needed on some systems)
991 Simple two microseconds delay
995 io7= [HW] IO7 for Marvel based alpha systems
996 See comment before marvel_specify_io7 in
997 arch/alpha/kernel/core_marvel.c.
1000 See Documentation/filesystems/nfsroot.txt.
1002 ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
1003 See comment before ip2_setup() in
1004 drivers/char/ip2/ip2base.c.
1006 ips= [HW,SCSI] Adaptec / IBM ServeRAID controller
1007 See header of drivers/scsi/ips.c.
1009 ports= [IP_VS_FTP] IPVS ftp helper module
1011 Up to 8 (IP_VS_APP_MAX_PORTS) ports
1013 Format: <port>,<port>....
1016 When an interrupt is not handled search all handlers
1017 for it. Intended to get systems with badly broken
1021 When an interrupt is not handled search all handlers
1022 for it. Also check all handlers each timer
1023 interrupt. Intended to get systems with badly broken
1027 Format: <RDP>,<reset>,<pci_scan>,<verbosity>
1029 isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
1031 <cpu number>,...,<cpu number>
1033 <cpu number>-<cpu number>
1034 (must be a positive range in ascending order)
1036 <cpu number>,...,<cpu number>-<cpu number>
1038 This option can be used to specify one or more CPUs
1039 to isolate from the general SMP balancing and scheduling
1040 algorithms. You can move a process onto or off an
1041 "isolated" CPU via the CPU affinity syscalls or cpuset.
1042 <cpu number> begins at 0 and the maximum value is
1043 "number of CPUs in system - 1".
1045 This option is the preferred way to isolate CPUs. The
1046 alternative -- manually setting the CPU mask of all
1047 tasks in the system -- can cause problems and
1048 suboptimal load balancer performance.
1052 js= [HW,JOY] Analog joystick
1053 See Documentation/input/joystick.txt.
1055 kernelcore=nn[KMG] [KNL,X86-32,IA-64,PPC,X86-64] This parameter
1056 specifies the amount of memory usable by the kernel
1057 for non-movable allocations. The requested amount is
1058 spread evenly throughout all nodes in the system. The
1059 remaining memory in each node is used for Movable
1060 pages. In the event, a node is too small to have both
1061 kernelcore and Movable pages, kernelcore pages will
1062 take priority and other nodes will have a larger number
1063 of kernelcore pages. The Movable zone is used for the
1064 allocation of pages that may be reclaimed or moved
1065 by the page migration subsystem. This means that
1066 HugeTLB pages may not be allocated from this zone.
1067 Note that allocations like PTEs-from-HighMem still
1068 use the HighMem zone if it exists, and the Normal
1069 zone if it does not.
1071 movablecore=nn[KMG] [KNL,X86-32,IA-64,PPC,X86-64] This parameter
1072 is similar to kernelcore except it specifies the
1073 amount of memory used for migratable allocations.
1074 If both kernelcore and movablecore is specified,
1075 then kernelcore will be at *least* the specified
1076 value but may be more. If movablecore on its own
1077 is specified, the administrator must be careful
1078 that the amount of memory usable for all allocations
1083 kstack=N [X86-32,X86-64] Print N words from the kernel stack
1086 kgdboc= [HW] kgdb over consoles.
1087 Requires a tty driver that supports console polling.
1088 (only serial suported for now)
1089 Format: <serial_device>[,baud]
1091 kmac= [MIPS] korina ethernet MAC address.
1092 Configure the RouterBoard 532 series on-chip
1093 Ethernet adapter MAC address.
1099 lapic [X86-32,APIC] Enable the local APIC even if BIOS
1102 lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer
1105 libata.dma= [LIBATA] DMA control
1106 libata.dma=0 Disable all PATA and SATA DMA
1107 libata.dma=1 PATA and SATA Disk DMA only
1108 libata.dma=2 ATAPI (CDROM) DMA only
1109 libata.dma=4 Compact Flash DMA only
1110 Combinations also work, so libata.dma=3 enables DMA
1111 for disks and CDROMs, but not CFs.
1113 libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
1117 libata.force= [LIBATA] Force configurations. The format is comma
1118 separated list of "[ID:]VAL" where ID is
1119 PORT[:DEVICE]. PORT and DEVICE are decimal numbers
1120 matching port, link or device. Basically, it matches
1121 the ATA ID string printed on console by libata. If
1122 the whole ID part is omitted, the last PORT and DEVICE
1123 values are used. If ID hasn't been specified yet, the
1124 configuration applies to all ports, links and devices.
1126 If only DEVICE is omitted, the parameter applies to
1127 the port and all links and devices behind it. DEVICE
1128 number of 0 either selects the first device or the
1129 first fan-out link behind PMP device. It does not
1130 select the host link. DEVICE number of 15 selects the
1131 host link and device attached to it.
1133 The VAL specifies the configuration to force. As long
1134 as there's no ambiguity shortcut notation is allowed.
1135 For example, both 1.5 and 1.5G would work for 1.5Gbps.
1136 The following configurations can be forced.
1138 * Cable type: 40c, 80c, short40c, unk, ign or sata.
1139 Any ID with matching PORT is used.
1141 * SATA link speed limit: 1.5Gbps or 3.0Gbps.
1143 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
1144 udma[/][16,25,33,44,66,100,133] notation is also
1147 * [no]ncq: Turn on or off NCQ.
1149 * nohrst, nosrst, norst: suppress hard, soft
1152 If there are multiple matching configurations changing
1153 the same attribute, the last one is used.
1155 lmb=debug [KNL] Enable lmb debug messages.
1157 load_ramdisk= [RAM] List of ramdisks to load from floppy
1158 See Documentation/blockdev/ramdisk.txt.
1160 lockd.nlm_grace_period=P [NFS] Assign grace period.
1163 lockd.nlm_tcpport=N [NFS] Assign TCP port.
1166 lockd.nlm_timeout=T [NFS] Assign timeout value.
1169 lockd.nlm_udpport=M [NFS] Assign UDP port.
1172 logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver
1175 loglevel= All Kernel Messages with a loglevel smaller than the
1176 console loglevel will be printed to the console. It can
1177 also be changed with klogd or other programs. The
1178 loglevels are defined as follows:
1180 0 (KERN_EMERG) system is unusable
1181 1 (KERN_ALERT) action must be taken immediately
1182 2 (KERN_CRIT) critical conditions
1183 3 (KERN_ERR) error conditions
1184 4 (KERN_WARNING) warning conditions
1185 5 (KERN_NOTICE) normal but significant condition
1186 6 (KERN_INFO) informational
1187 7 (KERN_DEBUG) debug-level messages
1189 log_buf_len=n Sets the size of the printk ring buffer, in bytes.
1190 Format: { n | nk | nM }
1191 n must be a power of two. The default size
1192 is set in the kernel config file.
1194 logo.nologo [FB] Disables display of the built-in Linux logo.
1195 This may be used to provide more screen space for
1196 kernel log messages and is useful when debugging
1197 kernel boot problems.
1199 lp=0 [LP] Specify parallel ports to use, e.g,
1200 lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
1201 lp=reset first parallel port). 'lp=0' disables the
1202 lp=auto printer driver. 'lp=reset' (which can be
1203 specified in addition to the ports) causes
1204 attached printers to be reset. Using
1205 lp=port1,port2,... specifies the parallel ports
1206 to associate lp devices with, starting with
1207 lp0. A port specification may be 'none' to skip
1208 that lp device, or a parport name such as
1209 'parport0'. Specifying 'lp=auto' instead of a
1210 port specification list means that device IDs
1211 from each port should be examined, to see if
1212 an IEEE 1284-compliant printer is attached; if
1213 so, the driver will manage that printer.
1214 See also header of drivers/char/lp.c.
1217 Sets loops_per_jiffy to given constant, thus avoiding
1218 time-consuming boot-time autodetection (up to 250 ms per
1219 CPU). 0 enables autodetection (default). To determine
1220 the correct value for your kernel, boot with normal
1221 autodetection and see what value is printed. Note that
1222 on SMP systems the preset will be applied to all CPUs,
1223 which is likely to cause problems if your CPUs need
1224 significantly divergent settings. An incorrect value
1225 will cause delays in the kernel to be wrong, leading to
1226 unpredictable I/O errors and other breakage. Although
1227 unlikely, in the extreme case this might damage your
1231 Format: <io>,<irq>,<dma>
1233 mac5380= [HW,SCSI] Format:
1234 <can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
1236 machvec= [IA64] Force the use of a particular machine-vector
1237 (machvec) in a generic kernel.
1238 Example: machvec=hpzx1_swiotlb
1240 max_loop= [LOOP] Maximum number of loopback devices that can
1244 maxcpus= [SMP] Maximum number of processors that an SMP kernel
1245 should make use of. maxcpus=n : n >= 0 limits the
1246 kernel to using 'n' processors. n=0 is a special case,
1247 it is equivalent to "nosmp", which also disables
1250 max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater than
1251 or equal to this physical address is ignored.
1253 max_luns= [SCSI] Maximum number of LUNs to probe.
1254 Should be between 1 and 2^32-1.
1257 [SCSI] Maximum number of LUNs received.
1258 Should be between 1 and 16384.
1262 mce [X86-32] Machine Check Exception
1264 mce=option [X86-64] See Documentation/x86/x86_64/boot-options.txt
1266 md= [HW] RAID subsystems devices and level
1267 See Documentation/md.txt.
1270 Format: <first>,<last>
1271 Specifies range of consoles to be captured by the MDA.
1273 mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory
1274 Amount of memory to be used when the kernel is not able
1275 to see the whole system memory or for test.
1276 [X86-32] Use together with memmap= to avoid physical
1277 address space collisions. Without memmap= PCI devices
1278 could be placed at addresses belonging to unused RAM.
1280 mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel
1284 [KNL,SH] Allow user to override the default size for
1285 per-device physically contiguous DMA buffers.
1287 memmap=exactmap [KNL,X86-32,X86_64] Enable setting of an exact
1288 E820 memory map, as specified by the user.
1289 Such memmap=exactmap lines can be constructed based on
1290 BIOS output or other requirements. See the memmap=nn@ss
1293 memmap=nn[KMG]@ss[KMG]
1294 [KNL] Force usage of a specific region of memory
1295 Region of memory to be used, from ss to ss+nn.
1297 memmap=nn[KMG]#ss[KMG]
1298 [KNL,ACPI] Mark specific memory as ACPI data.
1299 Region of memory to be used, from ss to ss+nn.
1301 memmap=nn[KMG]$ss[KMG]
1302 [KNL,ACPI] Mark specific memory as reserved.
1303 Region of memory to be used, from ss to ss+nn.
1304 Example: Exclude memory from 0x18690000-0x1869ffff
1305 memmap=64K$0x18690000
1307 memmap=0x10000$0x18690000
1309 memory_corruption_check=0/1 [X86]
1310 Some BIOSes seem to corrupt the first 64k of
1311 memory when doing things like suspend/resume.
1312 Setting this option will scan the memory
1313 looking for corruption. Enabling this will
1314 both detect corruption and prevent the kernel
1315 from using the memory being corrupted.
1316 However, its intended as a diagnostic tool; if
1317 repeatable BIOS-originated corruption always
1318 affects the same memory, you can use memmap=
1319 to prevent the kernel from using that memory.
1321 memory_corruption_check_size=size [X86]
1322 By default it checks for corruption in the low
1323 64k, making this memory unavailable for normal
1324 use. Use this parameter to scan for
1325 corruption in more or less memory.
1327 memory_corruption_check_period=seconds [X86]
1328 By default it checks for corruption every 60
1329 seconds. Use this parameter to check at some
1330 other rate. 0 disables periodic checking.
1332 memtest= [KNL,X86] Enable memtest
1334 range: 0,4 : pattern number
1335 default : 0 <disable>
1337 meye.*= [HW] Set MotionEye Camera parameters
1338 See Documentation/video4linux/meye.txt.
1340 mfgpt_irq= [IA-32] Specify the IRQ to use for the
1341 Multi-Function General Purpose Timers on AMD Geode
1344 mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when
1345 the BIOS has incorrectly applied a workaround. TinyBIOS
1346 version 0.98 is known to be affected, 0.99 fixes the
1347 problem by letting the user disable the workaround.
1351 min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
1352 physical address is ignored.
1355 [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
1356 parameter allows control of the logging verbosity for
1357 the additional memory initialisation checks. A value
1358 of 0 disables mminit logging and a level of 4 will
1359 log everything. Information is printed at KERN_DEBUG
1360 so loglevel=8 may also need to be specified.
1363 [MOUSE] Maximum time between finger touching and
1364 leaving touchpad surface for touch to be considered
1365 a tap and be reported as a left button click (for
1366 touchpads working in absolute mode only).
1368 mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
1369 reporting absolute coordinates, such as tablets
1370 mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
1371 reporting absolute coordinates, such as tablets
1376 MTD_Partition= [MTD]
1377 Format: <name>,<region-number>,<size>,<offset>
1379 MTD_Region= [MTD] Format:
1380 <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
1383 See drivers/mtd/cmdlinepart.c.
1386 ARM/S3C2412 JIVE boot control
1388 See arch/arm/mach-s3c2412/mach-jive.c
1390 mtouchusb.raw_coordinates=
1391 [HW] Make the MicroTouch USB driver use raw coordinates
1392 ('y', default) or cooked coordinates ('n')
1394 n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
1397 See header of drivers/scsi/NCR_D700.c.
1401 ncr53c400= [HW,SCSI]
1403 ncr53c400a= [HW,SCSI]
1405 ncr53c406a= [HW,SCSI]
1407 ncr53c8xx= [HW,SCSI]
1409 netdev= [NET] Network devices parameters
1410 Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
1411 Note that mem_start is often overloaded to mean
1412 something different and driver-specific.
1413 This usage is only documented in each driver source
1417 [NETFILTER] Enable connection tracking flow accounting
1418 0 to disable accounting
1419 1 to enable accounting
1420 Default value depends on CONFIG_NF_CT_ACCT that is
1421 going to be removed in 2.6.29.
1424 See Documentation/filesystems/nfsroot.txt.
1426 nfsroot= [NFS] nfs root filesystem for disk-less boxes.
1427 See Documentation/filesystems/nfsroot.txt.
1429 nfs.callback_tcpport=
1430 [NFS] set the TCP port on which the NFSv4 callback
1431 channel should listen.
1433 nfs.idmap_cache_timeout=
1434 [NFS] set the maximum lifetime for idmapper cache
1438 [NFS] enable 64-bit inode numbers.
1439 If zero, the NFS client will fake up a 32-bit inode
1440 number for the readdir() and stat() syscalls instead
1441 of returning the full 64-bit number.
1442 The default is to return 64-bit inode numbers.
1444 nmi_debug= [KNL,AVR32] Specify one or more actions to take
1445 when a NMI is triggered.
1446 Format: [state][,regs][,debounce][,die]
1448 nmi_watchdog= [KNL,BUGS=X86-32,X86-64] Debugging features for SMP kernels
1449 Format: [panic,][num]
1451 0 - turn nmi_watchdog off
1452 1 - use the IO-APIC timer for the NMI watchdog
1453 2 - use the local APIC for the NMI watchdog using
1454 a performance counter. Note: This will use one performance
1455 counter and the local APIC's performance vector.
1456 When panic is specified panic when an NMI watchdog timeout occurs.
1457 This is useful when you use a panic=... timeout and need the box
1459 Instead of 1 and 2 it is possible to use the following
1460 symbolic names: lapic and ioapic
1461 Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic
1463 no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
1464 emulation library even if a 387 maths coprocessor
1467 noaliencache [MM, NUMA, SLAB] Disables the allocation of alien
1468 caches in the slab allocator. Saves per-node memory,
1469 but will impact performance.
1473 noapic [SMP,APIC] Tells the kernel to not make use of any
1474 IOAPICs that may be present in the system.
1476 nobats [PPC] Do not use BATs for mapping kernel lowmem
1477 on "Classic" PPC cores.
1481 nodelayacct [KNL] Disable per-task delay accounting
1483 nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
1485 nodsp [SH] Disable hardware DSP at boot time.
1487 noefi [X86-32,X86-64] Disable EFI runtime services support.
1491 noexec [X86-32,X86-64]
1492 On X86-32 available only on PAE configured kernels.
1493 noexec=on: enable non-executable mappings (default)
1494 noexec=off: disable non-executable mappings
1497 This affects only 32-bit executables.
1498 noexec32=on: enable non-executable mappings (default)
1499 read doesn't imply executable mappings
1500 noexec32=off: disable non-executable mappings
1501 read implies executable mappings
1503 nofpu [SH] Disable hardware FPU at boot time.
1505 nofxsr [BUGS=X86-32] Disables x86 floating point extended
1506 register save and restore. The kernel will only save
1507 legacy floating-point registers on task switch.
1509 noclflush [BUGS=X86] Don't use the CLFLUSH instruction
1513 no-hlt [BUGS=X86-32] Tells the kernel that the hlt
1514 instruction doesn't work correctly and not to
1517 no_file_caps Tells the kernel not to honor file capabilities. The
1518 only way then for a file to be executed with privilege
1519 is to be setuid root or executed by root.
1521 nohalt [IA-64] Tells the kernel not to use the power saving
1522 function PAL_HALT_LIGHT when idle. This increases
1523 power-consumption. On the positive side, it reduces
1524 interrupt wake-up latency, which may improve performance
1525 in certain environments such as networked servers or
1528 nohz= [KNL] Boottime enable/disable dynamic ticks
1529 Valid arguments: on, off
1532 noirqdebug [X86-32] Disables the code which attempts to detect and
1533 disable unhandled interrupt sources.
1535 no_timer_check [X86-32,X86_64,APIC] Disables the code which tests for
1536 broken timer IRQ sources.
1538 noisapnp [ISAPNP] Disables ISA PnP code.
1540 noinitrd [RAM] Tells the kernel not to load any configured
1545 nojitter [IA64] Disables jitter checking for ITC timers.
1547 nolapic [X86-32,APIC] Do not enable or use the local APIC.
1549 nolapic_timer [X86-32,APIC] Do not use the local APIC timer.
1551 nox2apic [X86-64,APIC] Do not enable x2APIC mode.
1553 x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of
1554 default x2apic cluster mode on platforms
1557 noltlbs [PPC] Do not use large page/tlb entries for kernel
1558 lowmem mapping on PPC40x.
1560 nomca [IA-64] Disable machine check abort handling
1562 nomce [X86-32] Machine Check Exception
1564 nomfgpt [X86-32] Disable Multi-Function General Purpose
1565 Timer usage (for AMD Geode machines).
1567 noreplace-paravirt [X86-32,PV_OPS] Don't patch paravirt_ops
1569 noreplace-smp [X86-32,SMP] Don't replace SMP instructions
1570 with UP alternatives
1572 noresidual [PPC] Don't use residual data on PReP machines.
1574 noresume [SWSUSP] Disables resume and restores original swap
1577 no-scroll [VGA] Disables scrollback.
1578 This is required for the Braillex ib80-piezo Braille
1579 reader made by F.H. Papenmeier (Germany).
1583 nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support.
1585 nosmp [SMP] Tells an SMP kernel to act as a UP kernel,
1586 and disable the IO APIC. legacy for "maxcpus=0".
1588 nosoftlockup [KNL] Disable the soft-lockup detector.
1590 noswapaccount [KNL] Disable accounting of swap in memory resource
1591 controller. (See Documentation/controllers/memory.txt)
1593 nosync [HW,M68K] Disables sync negotiation for all devices.
1595 notsc [BUGS=X86-32] Disable Time Stamp Counter
1597 nousb [USB] Disable the USB subsystem
1601 nptcg= [IA64] Override max number of concurrent global TLB
1602 purges which is reported from either PAL_VM_SUMMARY or
1605 numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
1606 one of ['zone', 'node', 'default'] can be specified
1607 This can be set from sysctl after boot.
1608 See Documentation/sysctl/vm.txt for details.
1610 nr_uarts= [SERIAL] maximum number of UARTs to be registered.
1612 ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
1613 See Documentation/debugging-via-ohci1394.txt for more
1616 olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
1617 Rather than timing out after 20 ms if an EC
1618 command is not properly ACKed, override the length
1619 of the timeout. We have interrupts disabled while
1620 waiting for the ACK, so if this is set too high
1621 interrupts *may* be lost!
1626 oprofile.timer= [HW]
1627 Use timer interrupt instead of performance counters
1629 osst= [HW,SCSI] SCSI Tape Driver
1630 Format: <buffer_size>,<write_threshold>
1631 See also Documentation/scsi/st.txt.
1633 panic= [KNL] Kernel behaviour on panic
1636 parkbd.port= [HW] Parallel port number the keyboard adapter is
1637 connected to, default is 0.
1639 parkbd.mode= [HW] Parallel port keyboard adapter mode of operation,
1640 0 for XT, 1 for AT (default is AT).
1643 parport= [HW,PPT] Specify parallel ports. 0 disables.
1644 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] }
1645 Use 'auto' to force the driver to use any
1646 IRQ/DMA settings detected (the default is to
1647 ignore detected IRQ/DMA settings because of
1648 possible conflicts). You can specify the base
1649 address, IRQ, and DMA settings; IRQ and DMA
1650 should be numbers, or 'auto' (for using detected
1651 settings on that particular port), or 'nofifo'
1652 (to avoid using a FIFO even if it is detected).
1653 Parallel ports are assigned in the order they
1654 are specified on the command line, starting
1657 parport_init_mode= [HW,PPT]
1658 Configure VIA parallel port to operate in
1659 a specific mode. This is necessary on Pegasos
1660 computer where firmware has no options for setting
1661 up parallel port mode and sets it to spp.
1662 Currently this function knows 686a and 8231 chips.
1663 Format: [spp|ps2|epp|ecp|ecpepp]
1665 pas2= [HW,OSS] Format:
1666 <io>,<irq>,<dma>,<dma16>,<sb_io>,<sb_irq>,<sb_dma>,<sb_dma16>
1669 See header of drivers/scsi/pas16.c.
1672 Halt all CPUs after the first oops has been printed for
1673 the specified number of seconds. This is to be used if
1674 your oopses keep scrolling off the screen.
1679 See header of drivers/block/paride/pcd.c.
1680 See also Documentation/blockdev/paride.txt.
1682 pci=option[,option...] [PCI] various PCI subsystem options:
1683 off [X86] don't probe for the PCI bus
1684 bios [X86-32] force use of PCI BIOS, don't access
1685 the hardware directly. Use this if your machine
1686 has a non-standard PCI host bridge.
1687 nobios [X86-32] disallow use of PCI BIOS, only direct
1688 hardware access methods are allowed. Use this
1689 if you experience crashes upon bootup and you
1690 suspect they are caused by the BIOS.
1691 conf1 [X86] Force use of PCI Configuration
1693 conf2 [X86] Force use of PCI Configuration
1695 noaer [PCIE] If the PCIEAER kernel config parameter is
1696 enabled, this kernel boot option can be used to
1697 disable the use of PCIE advanced error reporting.
1698 nodomains [PCI] Disable support for multiple PCI
1699 root domains (aka PCI segments, in ACPI-speak).
1700 nommconf [X86-32,X86_64] Disable use of MMCONFIG for PCI
1702 nomsi [MSI] If the PCI_MSI kernel config parameter is
1703 enabled, this kernel boot option can be used to
1704 disable the use of MSI interrupts system-wide.
1705 noioapicquirk [APIC] Disable all boot interrupt quirks.
1706 Safety option to keep boot IRQs enabled. This
1707 should never be necessary.
1708 ioapicreroute [APIC] Enable rerouting of boot IRQs to the
1709 primary IO-APIC for bridges that cannot disable
1710 boot IRQs. This fixes a source of spurious IRQs
1711 when the system masks IRQs.
1712 noioapicreroute [APIC] Disable workaround that uses the
1713 boot IRQ equivalent of an IRQ that connects to
1714 a chipset where boot IRQs cannot be disabled.
1715 The opposite of ioapicreroute.
1716 biosirq [X86-32] Use PCI BIOS calls to get the interrupt
1717 routing table. These calls are known to be buggy
1718 on several machines and they hang the machine
1719 when used, but on other computers it's the only
1720 way to get the interrupt routing table. Try
1721 this option if the kernel is unable to allocate
1722 IRQs or discover secondary PCI buses on your
1724 rom [X86] Assign address space to expansion ROMs.
1725 Use with caution as certain devices share
1726 address decoders between ROMs and other
1728 norom [X86] Do not assign address space to
1729 expansion ROMs that do not already have
1730 BIOS assigned address ranges.
1731 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
1732 assigned automatically to PCI devices. You can
1733 make the kernel exclude IRQs of your ISA cards
1735 pirqaddr=0xAAAAA [X86] Specify the physical address
1736 of the PIRQ table (normally generated
1737 by the BIOS) if it is outside the
1738 F0000h-100000h range.
1739 lastbus=N [X86] Scan all buses thru bus #N. Can be
1740 useful if the kernel is unable to find your
1741 secondary buses and you want to tell it
1742 explicitly which ones they are.
1743 assign-busses [X86] Always assign all PCI bus
1744 numbers ourselves, overriding
1745 whatever the firmware may have done.
1746 usepirqmask [X86] Honor the possible IRQ mask stored
1747 in the BIOS $PIR table. This is needed on
1748 some systems with broken BIOSes, notably
1749 some HP Pavilion N5400 and Omnibook XE3
1750 notebooks. This will have no effect if ACPI
1751 IRQ routing is enabled.
1752 noacpi [X86] Do not use ACPI for IRQ routing
1753 or for PCI scanning.
1754 use_crs [X86] Use _CRS for PCI resource
1756 routeirq Do IRQ routing for all PCI devices.
1757 This is normally done in pci_enable_device(),
1758 so this option is a temporary workaround
1759 for broken drivers that don't call it.
1760 skip_isa_align [X86] do not align io start addr, so can
1761 handle more pci cards
1762 firmware [ARM] Do not re-enumerate the bus but instead
1763 just use the configuration from the
1764 bootloader. This is currently used on
1765 IXP2000 systems where the bus has to be
1766 configured a certain way for adjunct CPUs.
1767 noearly [X86] Don't do any early type 1 scanning.
1768 This might help on some broken boards which
1769 machine check when some devices' config space
1770 is read. But various workarounds are disabled
1771 and some IOMMU drivers will not work.
1772 bfsort Sort PCI devices into breadth-first order.
1773 This sorting is done to get a device
1774 order compatible with older (<= 2.4) kernels.
1775 nobfsort Don't sort PCI devices into breadth-first order.
1776 cbiosize=nn[KMG] The fixed amount of bus space which is
1777 reserved for the CardBus bridge's IO window.
1778 The default value is 256 bytes.
1779 cbmemsize=nn[KMG] The fixed amount of bus space which is
1780 reserved for the CardBus bridge's memory
1781 window. The default value is 64 megabytes.
1783 pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
1786 force Enable ASPM even on devices that claim not to support it.
1787 WARNING: Forcing ASPM on may cause system lockups.
1789 pcmv= [HW,PCMCIA] BadgePAD 4
1792 See Documentation/blockdev/paride.txt.
1794 pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at
1797 See arch/parisc/kernel/pdc_chassis.c
1800 See Documentation/blockdev/paride.txt.
1803 See Documentation/blockdev/paride.txt.
1805 pirq= [SMP,APIC] Manual mp-table setup
1806 See Documentation/x86/i386/IO-APIC.txt.
1808 plip= [PPT,NET] Parallel port network link
1809 Format: { parport<nr> | timid | 0 }
1810 See also Documentation/parport.txt.
1812 pmtmr= [X86] Manual setup of pmtmr I/O Port.
1813 Override pmtimer IOPort with a hex value.
1817 Enable PNP debug messages. This depends on the
1818 CONFIG_PNP_DEBUG_MESSAGES option.
1824 { on | off | curr | res | no-curr | no-res }
1827 [ISAPNP] Exclude IRQs for the autoconfiguration
1830 [ISAPNP] Exclude DMAs for the autoconfiguration
1832 pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration
1833 Ranges are in pairs (I/O port base and size).
1836 [ISAPNP] Exclude memory regions for the
1838 Ranges are in pairs (memory base and size).
1840 print-fatal-signals=
1841 [KNL] debug: print fatal signals
1842 print-fatal-signals=1: print segfault info to
1846 printk.time= Show timing data prefixed to each printk message line
1847 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
1849 profile= [KNL] Enable kernel profiling via /proc/profile
1850 Format: [schedule,]<number>
1851 Param: "schedule" - profile schedule points.
1852 Param: <number> - step/bucket size as a power of 2 for
1853 statistical time based profiling.
1854 Param: "sleep" - profile D-state sleeping (millisecs).
1855 Requires CONFIG_SCHEDSTATS
1856 Param: "kvm" - profile VM exits.
1858 processor.max_cstate= [HW,ACPI]
1859 Limit processor to maximum C-state
1860 max_cstate=9 overrides any DMI blacklist limit.
1862 processor.nocst [HW,ACPI]
1863 Ignore the _CST method to determine C-states,
1864 instead using the legacy FADT method
1866 prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk
1868 See Documentation/blockdev/ramdisk.txt.
1870 psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to
1871 probe for; one of (bare|imps|exps|lifebook|any).
1872 psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports
1874 psmouse.resetafter= [HW,MOUSE]
1875 Try to reset the device after so many bad packets
1878 [HW,MOUSE] Set desired mouse resolution, in dpi.
1879 psmouse.smartscroll=
1880 [HW,MOUSE] Controls Logitech smartscroll autorepeat.
1881 0 = disabled, 1 = enabled (default).
1883 pss= [HW,OSS] Personal Sound System (ECHO ESC614)
1885 <io>,<mss_io>,<mss_irq>,<mss_dma>,<mpu_io>,<mpu_irq>
1888 See Documentation/blockdev/paride.txt.
1891 [KNL] Number of legacy pty's. Overwrites compiled-in
1894 quiet [KNL] Disable most log messages
1899 See Documentation/md.txt.
1901 ramdisk_blocksize= [RAM]
1902 See Documentation/blockdev/ramdisk.txt.
1904 ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
1905 See Documentation/blockdev/ramdisk.txt.
1907 rcupdate.blimit= [KNL,BOOT]
1908 Set maximum number of finished RCU callbacks to process
1911 rcupdate.qhimark= [KNL,BOOT]
1912 Set threshold of queued
1913 RCU callbacks over which batch limiting is disabled.
1915 rcupdate.qlowmark= [KNL,BOOT]
1916 Set threshold of queued RCU callbacks below which
1917 batch limiting is re-enabled.
1921 Run specified binary instead of /init from the ramdisk,
1922 used for early userspace startup. See initrd.
1924 reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
1925 Format: <reboot_mode>[,<reboot_mode2>[,...]]
1926 See arch/*/kernel/reboot.c or arch/*/kernel/process.c
1929 [KNL, SMP] Set scheduler's default relax_domain_level.
1930 See Documentation/cpusets.txt.
1932 reserve= [KNL,BUGS] Force the kernel to ignore some iomem area
1934 reservetop= [X86-32]
1936 Reserves a hole at the top of the kernel virtual
1939 reset_devices [KNL] Force drivers to reset the underlying device
1940 during initialization.
1943 Specify the partition device for software suspend
1945 resume_offset= [SWSUSP]
1946 Specify the offset from the beginning of the partition
1947 given by "resume=" at which the swap header is located,
1948 in <PAGE_SIZE> units (needed only for swap files).
1949 See Documentation/power/swsusp-and-swap-files.txt
1951 retain_initrd [RAM] Keep initrd memory after extraction
1953 rhash_entries= [KNL,NET]
1954 Set number of hash buckets for route cache
1956 riscom8= [HW,SERIAL]
1957 Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
1959 ro [KNL] Mount root device read-only on boot
1961 root= [KNL] Root filesystem
1963 rootdelay= [KNL] Delay (in seconds) to pause before attempting to
1964 mount the root filesystem
1966 rootflags= [KNL] Set root filesystem mount option string
1968 rootfstype= [KNL] Set root filesystem type
1970 rootwait [KNL] Wait (indefinitely) for root device to show up.
1971 Useful for devices that are detected asynchronously
1972 (e.g. USB and MMC devices).
1974 root_plug.vendor_id=
1975 [ROOTPLUG] Override the default vendor ID
1977 root_plug.product_id=
1978 [ROOTPLUG] Override the default product ID
1981 [ROOTPLUG] Enable debugging output
1983 rw [KNL] Mount root device read-write on boot
1985 S [KNL] Run init in single mode
1988 See drivers/net/irda/sa1100_ir.c.
1990 sbni= [NET] Granch SBNI12 leased line adapter
1992 sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver
1993 Format: <io>[,<timeout>[,<isapnp>]]
1995 scsi_debug_*= [SCSI]
1996 See drivers/scsi/scsi_debug.c.
1998 scsi_default_dev_flags=
1999 [SCSI] SCSI default device flags
2002 scsi_dev_flags= [SCSI] Black/white list entry for vendor and model
2003 Format: <vendor>:<model>:<flags>
2004 (flags are integer value)
2006 scsi_logging_level= [SCSI] a bit mask of logging levels
2007 See drivers/scsi/scsi_logging.h for bits. Also
2008 settable via sysctl at dev.scsi.logging_level
2009 (/proc/sys/dev/scsi/logging_level).
2010 There is also a nice 'scsi_logging_level' script in the
2011 S390-tools package, available for download at
2012 http://www-128.ibm.com/developerworks/linux/linux390/s390-tools-1.5.4.html
2014 scsi_mod.scan= [SCSI] sync (default) scans SCSI busses as they are
2015 discovered. async scans them in kernel threads,
2016 allowing boot to proceed. none ignores them, expecting
2017 user space to do the scan.
2019 selinux [SELINUX] Disable or enable SELinux at boot time.
2020 Format: { "0" | "1" }
2021 See security/selinux/Kconfig help text.
2024 Default value is set via kernel config option.
2025 If enabled at boot time, /selinux/disable can be used
2026 later to disable prior to initial policy load.
2028 selinux_compat_net =
2029 [SELINUX] Set initial selinux_compat_net flag value.
2030 Format: { "0" | "1" }
2031 0 -- use new secmark-based packet controls
2032 1 -- use legacy packet controls
2033 Default value is 0 (preferred).
2034 Value can be changed at runtime via
2035 /selinux/compat_net.
2037 serialnumber [BUGS=X86-32]
2040 Maximal number of shapers.
2042 show_msr= [x86] show boot-time MSR settings
2043 Format: { <integer> }
2044 Show boot-time (BIOS-initialized) MSR settings.
2045 The parameter means the number of CPUs to show,
2046 for example 1 means boot CPU only.
2049 See header of drivers/scsi/sim710.c.
2056 slub_debug[=options[,slabs]] [MM, SLUB]
2057 Enabling slub_debug allows one to determine the
2058 culprit if slab objects become corrupted. Enabling
2059 slub_debug can create guard zones around objects and
2060 may poison objects when not in use. Also tracks the
2061 last alloc / free. For more information see
2062 Documentation/vm/slub.txt.
2064 slub_max_order= [MM, SLUB]
2065 Determines the maximum allowed order for slabs.
2066 A high setting may cause OOMs due to memory
2067 fragmentation. For more information see
2068 Documentation/vm/slub.txt.
2070 slub_min_objects= [MM, SLUB]
2071 The minimum number of objects per slab. SLUB will
2072 increase the slab order up to slub_max_order to
2073 generate a sufficiently large slab able to contain
2074 the number of objects indicated. The higher the number
2075 of objects the smaller the overhead of tracking slabs
2076 and the less frequently locks need to be acquired.
2077 For more information see Documentation/vm/slub.txt.
2079 slub_min_order= [MM, SLUB]
2080 Determines the mininum page order for slabs. Must be
2081 lower than slub_max_order.
2082 For more information see Documentation/vm/slub.txt.
2084 slub_nomerge [MM, SLUB]
2085 Disable merging of slabs with similar size. May be
2086 necessary if there is some reason to distinguish
2087 allocs to different slabs. Debug options disable
2088 merging on their own.
2089 For more information see Documentation/vm/slub.txt.
2092 Format: <io1>[,<io2>[,...,<io8>]]
2094 smp-alt-once [X86-32,SMP] On a hotplug CPU system, only
2095 attempt to substitute SMP alternatives once at boot.
2097 smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
2098 smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
2099 smsc-ircc2.ircc_sir= [HW] SIR base I/O port
2100 smsc-ircc2.ircc_fir= [HW] FIR base I/O port
2101 smsc-ircc2.ircc_irq= [HW] IRQ line
2102 smsc-ircc2.ircc_dma= [HW] DMA channel
2103 smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
2104 0: Toshiba Satellite 1800 (GP data pin select)
2105 1: Fast pin select (default)
2108 snd-ad1816a= [HW,ALSA]
2110 snd-ad1848= [HW,ALSA]
2112 snd-ali5451= [HW,ALSA]
2114 snd-als100= [HW,ALSA]
2116 snd-als4000= [HW,ALSA]
2118 snd-azt2320= [HW,ALSA]
2120 snd-cmi8330= [HW,ALSA]
2122 snd-cmipci= [HW,ALSA]
2124 snd-cs4231= [HW,ALSA]
2126 snd-cs4232= [HW,ALSA]
2128 snd-cs4236= [HW,ALSA]
2130 snd-cs4281= [HW,ALSA]
2132 snd-cs46xx= [HW,ALSA]
2134 snd-dt019x= [HW,ALSA]
2136 snd-dummy= [HW,ALSA]
2138 snd-emu10k1= [HW,ALSA]
2140 snd-ens1370= [HW,ALSA]
2142 snd-ens1371= [HW,ALSA]
2144 snd-es968= [HW,ALSA]
2146 snd-es1688= [HW,ALSA]
2148 snd-es18xx= [HW,ALSA]
2150 snd-es1938= [HW,ALSA]
2152 snd-es1968= [HW,ALSA]
2154 snd-fm801= [HW,ALSA]
2156 snd-gusclassic= [HW,ALSA]
2158 snd-gusextreme= [HW,ALSA]
2160 snd-gusmax= [HW,ALSA]
2164 snd-ice1712= [HW,ALSA]
2166 snd-intel8x0= [HW,ALSA]
2168 snd-interwave= [HW,ALSA]
2173 snd-korg1212= [HW,ALSA]
2175 snd-maestro3= [HW,ALSA]
2177 snd-mpu401= [HW,ALSA]
2179 snd-mtpav= [HW,ALSA]
2181 snd-nm256= [HW,ALSA]
2183 snd-opl3sa2= [HW,ALSA]
2191 snd-opti93x= [HW,ALSA]
2195 snd-rme32= [HW,ALSA]
2197 snd-rme96= [HW,ALSA]
2199 snd-rme9652= [HW,ALSA]
2205 snd-sbawe= [HW,ALSA]
2207 snd-serial= [HW,ALSA]
2209 snd-sgalaxy= [HW,ALSA]
2211 snd-sonicvibes= [HW,ALSA]
2216 snd-sun-cs4231= [HW,ALSA]
2218 snd-trident= [HW,ALSA]
2220 snd-usb-audio= [HW,ALSA,USB]
2222 snd-via82xx= [HW,ALSA]
2224 snd-virmidi= [HW,ALSA]
2226 snd-wavefront= [HW,ALSA]
2228 snd-ymfpci= [HW,ALSA]
2231 [KNL] Should the soft-lockup detector generate panics.
2233 sonypi.*= [HW] Sony Programmable I/O Control Device driver
2234 See Documentation/sonypi.txt
2236 specialix= [HW,SERIAL] Specialix multi-serial port adapter
2237 See Documentation/serial/specialix.txt.
2239 spia_io_base= [HW,MTD]
2245 Format: <io>,<irq>,<dma>,<mpu_io>,<mpu_irq>
2247 st= [HW,SCSI] SCSI tape parameters (buffers, etc.)
2248 See Documentation/scsi/st.txt.
2251 Enabled the stack tracer on boot up.
2255 Set the STI (builtin display/keyboard on the HP-PARISC
2256 machines) console (graphic card) which should be used
2257 as the initial boot-console.
2258 See also comment in drivers/video/console/sticore.c.
2261 See comment in drivers/video/console/sticore.c.
2264 Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
2268 Control how the NFS server code allocates CPUs to
2269 service thread pools. Depending on how many NICs
2270 you have and where their interrupts are bound, this
2271 option will affect which CPUs will do NFS serving.
2272 Note: this parameter cannot be changed while the
2273 NFS server is running.
2275 auto the server chooses an appropriate mode
2276 automatically using heuristics
2277 global a single global pool contains all CPUs
2278 percpu one pool for each CPU
2279 pernode one pool for each NUMA node (equivalent
2280 to global on non-NUMA machines)
2282 swiotlb= [IA-64] Number of I/O TLB slabs
2286 sym53c416= [HW,SCSI]
2287 See header of drivers/scsi/sym53c416.c.
2289 sysrq_always_enabled
2291 Ignore sysrq setting - this boot parameter will
2292 neutralize any effect of /proc/sys/kernel/sysrq.
2293 Useful for debugging.
2296 See header of drivers/scsi/t128.c.
2300 test_suspend= [SUSPEND]
2301 Specify "mem" (for Suspend-to-RAM) or "standby" (for
2302 standby suspend) as the system sleep state to briefly
2303 enter during system startup. The system is woken from
2304 this state using a wakeup-capable RTC alarm.
2306 thash_entries= [KNL,NET]
2307 Set number of hash buckets for TCP connection
2309 thermal.act= [HW,ACPI]
2310 -1: disable all active trip points in all thermal zones
2311 <degrees C>: override all lowest active trip points
2313 thermal.crt= [HW,ACPI]
2314 -1: disable all critical trip points in all thermal zones
2315 <degrees C>: override all critical trip points
2317 thermal.nocrt= [HW,ACPI]
2318 Set to disable actions on ACPI thermal zone
2319 critical and hot trip points.
2321 thermal.off= [HW,ACPI]
2322 1: disable ACPI thermal control
2324 thermal.psv= [HW,ACPI]
2325 -1: disable all passive trip points
2326 <degrees C>: override all passive trip points to this
2329 thermal.tzp= [HW,ACPI]
2330 Specify global default ACPI thermal zone polling rate
2331 <deci-seconds>: poll all this frequency
2332 0: no polling (default)
2335 See comment before function dc390_setup() in
2336 drivers/scsi/tmscsim.c.
2340 Specify if the kernel should make use of the cpu
2341 topology informations if the hardware supports these.
2342 The scheduler will make use of these informations and
2343 e.g. base its process migration decisions on it.
2348 trix= [HW,OSS] MediaTrix AudioTrix Pro
2350 <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
2352 tsc= Disable clocksource-must-verify flag for TSC.
2354 [x86] reliable: mark tsc clocksource as reliable, this
2355 disables clocksource verification at runtime.
2356 Used to enable high-resolution timer mode on older
2357 hardware, and in virtualized environment.
2359 turbografx.map[2|3]= [HW,JOY]
2360 TurboGraFX parallel port interface
2362 <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
2363 See also Documentation/input/joystick-parport.txt
2365 u14-34f= [HW,SCSI] UltraStor 14F/34F SCSI host adapter
2366 See header of drivers/scsi/u14-34f.c.
2375 [USB] Ignore overcurrent events (default N).
2376 Some badly-designed motherboards generate lots of
2377 bogus events, for ports that aren't wired to
2378 anything. Set this parameter to avoid log spamming.
2379 Note that genuine overcurrent events won't be
2384 Set unknown_nmi_panic=1 early on boot.
2386 usbcore.autosuspend=
2387 [USB] The autosuspend time delay (in seconds) used
2388 for newly-detected USB devices (default 2). This
2389 is the time required before an idle device will be
2390 autosuspended. Devices for which the delay is set
2391 to a negative value won't be autosuspended at all.
2393 usbcore.usbfs_snoop=
2394 [USB] Set to log all usbfs traffic (default 0 = off).
2396 usbcore.blinkenlights=
2397 [USB] Set to cycle leds on hubs (default 0 = off).
2399 usbcore.old_scheme_first=
2400 [USB] Start with the old device initialization
2401 scheme (default 0 = off).
2403 usbcore.use_both_schemes=
2404 [USB] Try the other device initialization scheme
2405 if the first one fails (default 1 = enabled).
2407 usbcore.initial_descriptor_timeout=
2408 [USB] Specifies timeout for the initial 64-byte
2409 USB_REQ_GET_DESCRIPTOR request in milliseconds
2410 (default 5000 = 5.0 seconds).
2413 [USBHID] The interval which mice are to be polled at.
2415 usb-storage.delay_use=
2416 [UMS] The delay in seconds before a new device is
2417 scanned for Logical Units (default 5).
2420 [UMS] A list of quirks entries to supplement or
2421 override the built-in unusual_devs list. List
2422 entries are separated by commas. Each entry has
2423 the form VID:PID:Flags where VID and PID are Vendor
2424 and Product ID values (4-digit hex numbers) and
2425 Flags is a set of characters, each corresponding
2426 to a common usb-storage quirk flag as follows:
2427 a = SANE_SENSE (collect more than 18 bytes
2429 c = FIX_CAPACITY (decrease the reported
2430 device capacity by one sector);
2431 h = CAPACITY_HEURISTICS (decrease the
2432 reported device capacity by one
2433 sector if the number is odd);
2434 i = IGNORE_DEVICE (don't bind to this
2436 l = NOT_LOCKABLE (don't try to lock and
2437 unlock ejectable media);
2438 m = MAX_SECTORS_64 (don't transfer more
2439 than 64 sectors = 32 KB at a time);
2440 o = CAPACITY_OK (accept the capacity
2441 reported by the device);
2442 r = IGNORE_RESIDUE (the device reports
2443 bogus residue values);
2444 s = SINGLE_LUN (the device has only one
2446 w = NO_WP_DETECT (don't test whether the
2447 medium is write-protected).
2448 Example: quirks=0419:aaf5:rl,0421:0433:rc
2450 add_efi_memmap [EFI; x86-32,X86-64] Include EFI memory map in
2451 kernel's map of available physical RAM.
2453 vdso= [X86-32,SH,x86-64]
2454 vdso=2: enable compat VDSO (default with COMPAT_VDSO)
2455 vdso=1: enable VDSO (default)
2456 vdso=0: disable VDSO mapping
2458 vdso32= [X86-32,X86-64]
2459 vdso32=2: enable compat VDSO (default with COMPAT_VDSO)
2460 vdso32=1: enable 32-bit VDSO (default)
2461 vdso32=0: disable 32-bit VDSO mapping
2464 vector=percpu: enable percpu vector domain
2466 video= [FB] Frame buffer configuration
2467 See Documentation/fb/modedb.txt.
2469 vga= [BOOT,X86-32] Select a particular video mode
2470 See Documentation/x86/boot.txt and
2471 Documentation/svga.txt.
2472 Use vga=ask for menu.
2473 This is actually a boot loader parameter; the value is
2474 passed to the kernel using a special protocol.
2476 vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact
2477 size of <nn>. This can be used to increase the
2478 minimum size (128MB on x86). It can also be used to
2479 decrease the size and leave more room for directly
2482 vmhalt= [KNL,S390] Perform z/VM CP command after system halt.
2485 vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic.
2488 vmpoff= [KNL,S390] Perform z/VM CP command after power off.
2491 waveartist= [HW,OSS]
2492 Format: <io>,<irq>,<dma>,<dma2>
2495 See header of drivers/scsi/wd33c93.c.
2498 See header of drivers/scsi/wd7000.c.
2501 See Documentation/watchdog/wdt.txt.
2503 xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
2504 xd_geo= See header of drivers/block/xd.c.
2506 xirc2ps_cs= [NET,PCMCIA]
2508 <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
2510 norandmaps Don't use address space randomization. Equivalent to
2511 echo 0 > /proc/sys/kernel/randomize_va_space
2513 ______________________________________________________________________
2517 Add documentation for ALSA options.
2518 Add more DRM drivers.