2 * Local APIC handling, local APIC timers
4 * (c) 1999, 2000 Ingo Molnar <mingo@redhat.com>
7 * Maciej W. Rozycki : Bits for genuine 82489DX APICs;
8 * thanks to Eric Gilmore
10 * for testing these extensively.
11 * Maciej W. Rozycki : Various updates and fixes.
12 * Mikael Pettersson : Power Management for UP-APIC.
14 * Mikael Pettersson : PM converted to driver model.
17 #include <linux/init.h>
20 #include <linux/delay.h>
21 #include <linux/bootmem.h>
22 #include <linux/interrupt.h>
23 #include <linux/mc146818rtc.h>
24 #include <linux/kernel_stat.h>
25 #include <linux/sysdev.h>
26 #include <linux/cpu.h>
27 #include <linux/clockchips.h>
28 #include <linux/acpi_pmtmr.h>
29 #include <linux/module.h>
30 #include <linux/dmi.h>
32 #include <asm/atomic.h>
35 #include <asm/mpspec.h>
37 #include <asm/arch_hooks.h>
39 #include <asm/i8253.h>
42 #include <mach_apic.h>
43 #include <mach_apicdef.h>
49 #if ((SPURIOUS_APIC_VECTOR & 0x0F) != 0x0F)
50 # error SPURIOUS_APIC_VECTOR definition error
53 unsigned long mp_lapic_addr;
56 * Knob to control our willingness to enable the local APIC.
60 static int force_enable_local_apic;
63 /* Disable local APIC timer from the kernel commandline or via dmi quirk */
64 static int disable_apic_timer __cpuinitdata;
65 /* Local APIC timer works in C2 */
66 int local_apic_timer_c2_ok;
67 EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok);
69 int first_system_vector = 0xfe;
71 char system_vectors[NR_VECTORS] = { [0 ... NR_VECTORS-1] = SYS_VECTOR_FREE};
74 * Debug level, exported for io_apic.c
76 unsigned int apic_verbosity;
80 /* Have we found an MP table */
83 static struct resource lapic_resource = {
85 .flags = IORESOURCE_MEM | IORESOURCE_BUSY,
88 static unsigned int calibration_result;
90 static int lapic_next_event(unsigned long delta,
91 struct clock_event_device *evt);
92 static void lapic_timer_setup(enum clock_event_mode mode,
93 struct clock_event_device *evt);
94 static void lapic_timer_broadcast(cpumask_t mask);
95 static void apic_pm_activate(void);
98 * The local apic timer can be used for any function which is CPU local.
100 static struct clock_event_device lapic_clockevent = {
102 .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT
103 | CLOCK_EVT_FEAT_C3STOP | CLOCK_EVT_FEAT_DUMMY,
105 .set_mode = lapic_timer_setup,
106 .set_next_event = lapic_next_event,
107 .broadcast = lapic_timer_broadcast,
111 static DEFINE_PER_CPU(struct clock_event_device, lapic_events);
113 /* Local APIC was disabled by the BIOS and enabled by the kernel */
114 static int enabled_via_apicbase;
116 static unsigned long apic_phys;
117 unsigned int __cpuinitdata maxcpus = NR_CPUS;
121 * Get the LAPIC version
123 static inline int lapic_get_version(void)
125 return GET_APIC_VERSION(apic_read(APIC_LVR));
129 * Check, if the APIC is integrated or a separate chip
131 static inline int lapic_is_integrated(void)
136 return APIC_INTEGRATED(lapic_get_version());
141 * Check, whether this is a modern or a first generation APIC
143 static int modern_apic(void)
145 /* AMD systems use old APIC versions, so check the CPU */
146 if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD &&
147 boot_cpu_data.x86 >= 0xf)
149 return lapic_get_version() >= 0x14;
153 * Paravirt kernels also might be using these below ops. So we still
154 * use generic apic_read()/apic_write(), which might be pointing to different
155 * ops in PARAVIRT case.
157 void xapic_wait_icr_idle(void)
159 while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
163 u32 safe_xapic_wait_icr_idle(void)
170 send_status = apic_read(APIC_ICR) & APIC_ICR_BUSY;
174 } while (timeout++ < 1000);
179 void xapic_icr_write(u32 low, u32 id)
181 apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(id));
182 apic_write(APIC_ICR, low);
185 u64 xapic_icr_read(void)
189 icr2 = apic_read(APIC_ICR2);
190 icr1 = apic_read(APIC_ICR);
192 return icr1 | ((u64)icr2 << 32);
195 static struct apic_ops xapic_ops = {
196 .read = native_apic_mem_read,
197 .write = native_apic_mem_write,
198 .icr_read = xapic_icr_read,
199 .icr_write = xapic_icr_write,
200 .wait_icr_idle = xapic_wait_icr_idle,
201 .safe_wait_icr_idle = safe_xapic_wait_icr_idle,
204 struct apic_ops __read_mostly *apic_ops = &xapic_ops;
205 EXPORT_SYMBOL_GPL(apic_ops);
208 * enable_NMI_through_LVT0 - enable NMI through local vector table 0
210 void __cpuinit enable_NMI_through_LVT0(void)
214 /* unmask and set to NMI */
217 /* Level triggered for 82489DX (32bit mode) */
218 if (!lapic_is_integrated())
219 v |= APIC_LVT_LEVEL_TRIGGER;
221 apic_write(APIC_LVT0, v);
225 * get_physical_broadcast - Get number of physical broadcast IDs
227 int get_physical_broadcast(void)
229 return modern_apic() ? 0xff : 0xf;
233 * lapic_get_maxlvt - get the maximum number of local vector table entries
235 int lapic_get_maxlvt(void)
239 v = apic_read(APIC_LVR);
241 * - we always have APIC integrated on 64bit mode
242 * - 82489DXs do not report # of LVT entries
244 return APIC_INTEGRATED(GET_APIC_VERSION(v)) ? GET_APIC_MAXLVT(v) : 2;
253 #define APIC_DIVISOR 1
255 #define APIC_DIVISOR 16
259 * This function sets up the local APIC timer, with a timeout of
260 * 'clocks' APIC bus clock. During calibration we actually call
261 * this function twice on the boot CPU, once with a bogus timeout
262 * value, second time for real. The other (noncalibrating) CPUs
263 * call this function only once, with the real, calibrated value.
265 * We do reads before writes even if unnecessary, to get around the
266 * P5 APIC double write bug.
268 static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
270 unsigned int lvtt_value, tmp_value;
272 lvtt_value = LOCAL_TIMER_VECTOR;
274 lvtt_value |= APIC_LVT_TIMER_PERIODIC;
275 if (!lapic_is_integrated())
276 lvtt_value |= SET_APIC_TIMER_BASE(APIC_TIMER_BASE_DIV);
279 lvtt_value |= APIC_LVT_MASKED;
281 apic_write(APIC_LVTT, lvtt_value);
286 tmp_value = apic_read(APIC_TDCR);
287 apic_write(APIC_TDCR,
288 (tmp_value & ~(APIC_TDR_DIV_1 | APIC_TDR_DIV_TMBASE)) |
292 apic_write(APIC_TMICT, clocks / APIC_DIVISOR);
296 * Setup extended LVT, AMD specific (K8, family 10h)
298 * Vector mappings are hard coded. On K8 only offset 0 (APIC500) and
299 * MCE interrupts are supported. Thus MCE offset must be set to 0.
302 #define APIC_EILVT_LVTOFF_MCE 0
303 #define APIC_EILVT_LVTOFF_IBS 1
305 static void setup_APIC_eilvt(u8 lvt_off, u8 vector, u8 msg_type, u8 mask)
307 unsigned long reg = (lvt_off << 4) + APIC_EILVT0;
308 unsigned int v = (mask << 16) | (msg_type << 8) | vector;
313 u8 setup_APIC_eilvt_mce(u8 vector, u8 msg_type, u8 mask)
315 setup_APIC_eilvt(APIC_EILVT_LVTOFF_MCE, vector, msg_type, mask);
316 return APIC_EILVT_LVTOFF_MCE;
319 u8 setup_APIC_eilvt_ibs(u8 vector, u8 msg_type, u8 mask)
321 setup_APIC_eilvt(APIC_EILVT_LVTOFF_IBS, vector, msg_type, mask);
322 return APIC_EILVT_LVTOFF_IBS;
326 * Program the next event, relative to now
328 static int lapic_next_event(unsigned long delta,
329 struct clock_event_device *evt)
331 apic_write(APIC_TMICT, delta);
336 * Setup the lapic timer in periodic or oneshot mode
338 static void lapic_timer_setup(enum clock_event_mode mode,
339 struct clock_event_device *evt)
344 /* Lapic used as dummy for broadcast ? */
345 if (evt->features & CLOCK_EVT_FEAT_DUMMY)
348 local_irq_save(flags);
351 case CLOCK_EVT_MODE_PERIODIC:
352 case CLOCK_EVT_MODE_ONESHOT:
353 __setup_APIC_LVTT(calibration_result,
354 mode != CLOCK_EVT_MODE_PERIODIC, 1);
356 case CLOCK_EVT_MODE_UNUSED:
357 case CLOCK_EVT_MODE_SHUTDOWN:
358 v = apic_read(APIC_LVTT);
359 v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
360 apic_write(APIC_LVTT, v);
362 case CLOCK_EVT_MODE_RESUME:
363 /* Nothing to do here */
367 local_irq_restore(flags);
371 * Local APIC timer broadcast function
373 static void lapic_timer_broadcast(cpumask_t mask)
376 send_IPI_mask(mask, LOCAL_TIMER_VECTOR);
381 * Setup the local APIC timer for this CPU. Copy the initilized values
382 * of the boot CPU and register the clock event in the framework.
384 static void __devinit setup_APIC_timer(void)
386 struct clock_event_device *levt = &__get_cpu_var(lapic_events);
388 memcpy(levt, &lapic_clockevent, sizeof(*levt));
389 levt->cpumask = cpumask_of_cpu(smp_processor_id());
391 clockevents_register_device(levt);
395 * In this functions we calibrate APIC bus clocks to the external timer.
397 * We want to do the calibration only once since we want to have local timer
398 * irqs syncron. CPUs connected by the same APIC bus have the very same bus
401 * This was previously done by reading the PIT/HPET and waiting for a wrap
402 * around to find out, that a tick has elapsed. I have a box, where the PIT
403 * readout is broken, so it never gets out of the wait loop again. This was
404 * also reported by others.
406 * Monitoring the jiffies value is inaccurate and the clockevents
407 * infrastructure allows us to do a simple substitution of the interrupt
410 * The calibration routine also uses the pm_timer when possible, as the PIT
411 * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes
412 * back to normal later in the boot process).
415 #define LAPIC_CAL_LOOPS (HZ/10)
417 static __initdata int lapic_cal_loops = -1;
418 static __initdata long lapic_cal_t1, lapic_cal_t2;
419 static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2;
420 static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2;
421 static __initdata unsigned long lapic_cal_j1, lapic_cal_j2;
424 * Temporary interrupt handler.
426 static void __init lapic_cal_handler(struct clock_event_device *dev)
428 unsigned long long tsc = 0;
429 long tapic = apic_read(APIC_TMCCT);
430 unsigned long pm = acpi_pm_read_early();
435 switch (lapic_cal_loops++) {
437 lapic_cal_t1 = tapic;
438 lapic_cal_tsc1 = tsc;
440 lapic_cal_j1 = jiffies;
443 case LAPIC_CAL_LOOPS:
444 lapic_cal_t2 = tapic;
445 lapic_cal_tsc2 = tsc;
446 if (pm < lapic_cal_pm1)
447 pm += ACPI_PM_OVRRUN;
449 lapic_cal_j2 = jiffies;
454 static int __init calibrate_APIC_clock(void)
456 struct clock_event_device *levt = &__get_cpu_var(lapic_events);
457 const long pm_100ms = PMTMR_TICKS_PER_SEC/10;
458 const long pm_thresh = pm_100ms/100;
459 void (*real_handler)(struct clock_event_device *dev);
460 unsigned long deltaj;
462 int pm_referenced = 0;
466 /* Replace the global interrupt handler */
467 real_handler = global_clock_event->event_handler;
468 global_clock_event->event_handler = lapic_cal_handler;
471 * Setup the APIC counter to 1e9. There is no way the lapic
472 * can underflow in the 100ms detection time frame
474 __setup_APIC_LVTT(1000000000, 0, 0);
476 /* Let the interrupts run */
479 while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
484 /* Restore the real event handler */
485 global_clock_event->event_handler = real_handler;
487 /* Build delta t1-t2 as apic timer counts down */
488 delta = lapic_cal_t1 - lapic_cal_t2;
489 apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta);
491 /* Check, if the PM timer is available */
492 deltapm = lapic_cal_pm2 - lapic_cal_pm1;
493 apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm);
499 mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22);
501 if (deltapm > (pm_100ms - pm_thresh) &&
502 deltapm < (pm_100ms + pm_thresh)) {
503 apic_printk(APIC_VERBOSE, "... PM timer result ok\n");
505 res = (((u64) deltapm) * mult) >> 22;
506 do_div(res, 1000000);
507 printk(KERN_WARNING "APIC calibration not consistent "
508 "with PM Timer: %ldms instead of 100ms\n",
510 /* Correct the lapic counter value */
511 res = (((u64) delta) * pm_100ms);
512 do_div(res, deltapm);
513 printk(KERN_INFO "APIC delta adjusted to PM-Timer: "
514 "%lu (%ld)\n", (unsigned long) res, delta);
520 /* Calculate the scaled math multiplication factor */
521 lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS,
522 lapic_clockevent.shift);
523 lapic_clockevent.max_delta_ns =
524 clockevent_delta2ns(0x7FFFFF, &lapic_clockevent);
525 lapic_clockevent.min_delta_ns =
526 clockevent_delta2ns(0xF, &lapic_clockevent);
528 calibration_result = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS;
530 apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta);
531 apic_printk(APIC_VERBOSE, "..... mult: %ld\n", lapic_clockevent.mult);
532 apic_printk(APIC_VERBOSE, "..... calibration result: %u\n",
536 delta = (long)(lapic_cal_tsc2 - lapic_cal_tsc1);
537 apic_printk(APIC_VERBOSE, "..... CPU clock speed is "
539 (delta / LAPIC_CAL_LOOPS) / (1000000 / HZ),
540 (delta / LAPIC_CAL_LOOPS) % (1000000 / HZ));
543 apic_printk(APIC_VERBOSE, "..... host bus clock speed is "
545 calibration_result / (1000000 / HZ),
546 calibration_result % (1000000 / HZ));
549 * Do a sanity check on the APIC calibration result
551 if (calibration_result < (1000000 / HZ)) {
554 "APIC frequency too slow, disabling apic timer\n");
558 levt->features &= ~CLOCK_EVT_FEAT_DUMMY;
560 /* We trust the pm timer based calibration */
561 if (!pm_referenced) {
562 apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
565 * Setup the apic timer manually
567 levt->event_handler = lapic_cal_handler;
568 lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt);
569 lapic_cal_loops = -1;
571 /* Let the interrupts run */
574 while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
579 /* Stop the lapic timer */
580 lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
585 deltaj = lapic_cal_j2 - lapic_cal_j1;
586 apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
588 /* Check, if the jiffies result is consistent */
589 if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2)
590 apic_printk(APIC_VERBOSE, "... jiffies result ok\n");
592 levt->features |= CLOCK_EVT_FEAT_DUMMY;
596 if (levt->features & CLOCK_EVT_FEAT_DUMMY) {
598 "APIC timer disabled due to verification failure.\n");
606 * Setup the boot APIC
608 * Calibrate and verify the result.
610 void __init setup_boot_APIC_clock(void)
613 * The local apic timer can be disabled via the kernel
614 * commandline or from the CPU detection code. Register the lapic
615 * timer as a dummy clock event source on SMP systems, so the
616 * broadcast mechanism is used. On UP systems simply ignore it.
618 if (disable_apic_timer) {
619 printk(KERN_INFO "Disabling APIC timer\n");
620 /* No broadcast on UP ! */
621 if (num_possible_cpus() > 1) {
622 lapic_clockevent.mult = 1;
628 apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
629 "calibrating APIC timer ...\n");
631 if (calibrate_APIC_clock()) {
632 /* No broadcast on UP ! */
633 if (num_possible_cpus() > 1)
639 * If nmi_watchdog is set to IO_APIC, we need the
640 * PIT/HPET going. Otherwise register lapic as a dummy
643 if (nmi_watchdog != NMI_IO_APIC)
644 lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
646 printk(KERN_WARNING "APIC timer registered as dummy,"
647 " due to nmi_watchdog=%d!\n", nmi_watchdog);
649 /* Setup the lapic or request the broadcast */
653 void __devinit setup_secondary_APIC_clock(void)
659 * The guts of the apic timer interrupt
661 static void local_apic_timer_interrupt(void)
663 int cpu = smp_processor_id();
664 struct clock_event_device *evt = &per_cpu(lapic_events, cpu);
667 * Normally we should not be here till LAPIC has been initialized but
668 * in some cases like kdump, its possible that there is a pending LAPIC
669 * timer interrupt from previous kernel's context and is delivered in
670 * new kernel the moment interrupts are enabled.
672 * Interrupts are enabled early and LAPIC is setup much later, hence
673 * its possible that when we get here evt->event_handler is NULL.
674 * Check for event_handler being NULL and discard the interrupt as
677 if (!evt->event_handler) {
679 "Spurious LAPIC timer interrupt on cpu %d\n", cpu);
681 lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, evt);
686 * the NMI deadlock-detector uses this.
689 add_pda(apic_timer_irqs, 1);
691 per_cpu(irq_stat, cpu).apic_timer_irqs++;
694 evt->event_handler(evt);
698 * Local APIC timer interrupt. This is the most natural way for doing
699 * local interrupts, but local timer interrupts can be emulated by
700 * broadcast interrupts too. [in case the hw doesn't support APIC timers]
702 * [ if a single-CPU system runs an SMP kernel then we call the local
703 * interrupt as well. Thus we cannot inline the local irq ... ]
705 void smp_apic_timer_interrupt(struct pt_regs *regs)
707 struct pt_regs *old_regs = set_irq_regs(regs);
710 * NOTE! We'd better ACK the irq immediately,
711 * because timer handling can be slow.
715 * update_process_times() expects us to have done irq_enter().
716 * Besides, if we don't timer interrupts ignore the global
717 * interrupt lock, which is the WrongThing (tm) to do.
720 local_apic_timer_interrupt();
723 set_irq_regs(old_regs);
726 int setup_profiling_timer(unsigned int multiplier)
732 * Local APIC start and shutdown
736 * clear_local_APIC - shutdown the local APIC
738 * This is called, when a CPU is disabled and before rebooting, so the state of
739 * the local APIC has no dangling leftovers. Also used to cleanout any BIOS
740 * leftovers during boot.
742 void clear_local_APIC(void)
747 /* APIC hasn't been mapped yet */
751 maxlvt = lapic_get_maxlvt();
753 * Masking an LVT entry can trigger a local APIC error
754 * if the vector is zero. Mask LVTERR first to prevent this.
757 v = ERROR_APIC_VECTOR; /* any non-zero vector will do */
758 apic_write(APIC_LVTERR, v | APIC_LVT_MASKED);
761 * Careful: we have to set masks only first to deassert
762 * any level-triggered sources.
764 v = apic_read(APIC_LVTT);
765 apic_write(APIC_LVTT, v | APIC_LVT_MASKED);
766 v = apic_read(APIC_LVT0);
767 apic_write(APIC_LVT0, v | APIC_LVT_MASKED);
768 v = apic_read(APIC_LVT1);
769 apic_write(APIC_LVT1, v | APIC_LVT_MASKED);
771 v = apic_read(APIC_LVTPC);
772 apic_write(APIC_LVTPC, v | APIC_LVT_MASKED);
775 /* lets not touch this if we didn't frob it */
776 #if defined(CONFIG_X86_MCE_P4THERMAL) || defined(X86_MCE_INTEL)
778 v = apic_read(APIC_LVTTHMR);
779 apic_write(APIC_LVTTHMR, v | APIC_LVT_MASKED);
783 * Clean APIC state for other OSs:
785 apic_write(APIC_LVTT, APIC_LVT_MASKED);
786 apic_write(APIC_LVT0, APIC_LVT_MASKED);
787 apic_write(APIC_LVT1, APIC_LVT_MASKED);
789 apic_write(APIC_LVTERR, APIC_LVT_MASKED);
791 apic_write(APIC_LVTPC, APIC_LVT_MASKED);
793 /* Integrated APIC (!82489DX) ? */
794 if (lapic_is_integrated()) {
796 /* Clear ESR due to Pentium errata 3AP and 11AP */
797 apic_write(APIC_ESR, 0);
803 * disable_local_APIC - clear and disable the local APIC
805 void disable_local_APIC(void)
812 * Disable APIC (implies clearing of registers
815 value = apic_read(APIC_SPIV);
816 value &= ~APIC_SPIV_APIC_ENABLED;
817 apic_write(APIC_SPIV, value);
821 * When LAPIC was disabled by the BIOS and enabled by the kernel,
822 * restore the disabled state.
824 if (enabled_via_apicbase) {
827 rdmsr(MSR_IA32_APICBASE, l, h);
828 l &= ~MSR_IA32_APICBASE_ENABLE;
829 wrmsr(MSR_IA32_APICBASE, l, h);
835 * If Linux enabled the LAPIC against the BIOS default disable it down before
836 * re-entering the BIOS on shutdown. Otherwise the BIOS may get confused and
837 * not power-off. Additionally clear all LVT entries before disable_local_APIC
838 * for the case where Linux didn't enable the LAPIC.
840 void lapic_shutdown(void)
847 local_irq_save(flags);
850 if (!enabled_via_apicbase)
854 disable_local_APIC();
857 local_irq_restore(flags);
861 * This is to verify that we're looking at a real local APIC.
862 * Check these against your board if the CPUs aren't getting
863 * started for no apparent reason.
865 int __init verify_local_APIC(void)
867 unsigned int reg0, reg1;
870 * The version register is read-only in a real APIC.
872 reg0 = apic_read(APIC_LVR);
873 apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg0);
874 apic_write(APIC_LVR, reg0 ^ APIC_LVR_MASK);
875 reg1 = apic_read(APIC_LVR);
876 apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg1);
879 * The two version reads above should print the same
880 * numbers. If the second one is different, then we
881 * poke at a non-APIC.
887 * Check if the version looks reasonably.
889 reg1 = GET_APIC_VERSION(reg0);
890 if (reg1 == 0x00 || reg1 == 0xff)
892 reg1 = lapic_get_maxlvt();
893 if (reg1 < 0x02 || reg1 == 0xff)
897 * The ID register is read/write in a real APIC.
899 reg0 = apic_read(APIC_ID);
900 apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg0);
901 apic_write(APIC_ID, reg0 ^ APIC_ID_MASK);
902 reg1 = apic_read(APIC_ID);
903 apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg1);
904 apic_write(APIC_ID, reg0);
905 if (reg1 != (reg0 ^ APIC_ID_MASK))
909 * The next two are just to see if we have sane values.
910 * They're only really relevant if we're in Virtual Wire
911 * compatibility mode, but most boxes are anymore.
913 reg0 = apic_read(APIC_LVT0);
914 apic_printk(APIC_DEBUG, "Getting LVT0: %x\n", reg0);
915 reg1 = apic_read(APIC_LVT1);
916 apic_printk(APIC_DEBUG, "Getting LVT1: %x\n", reg1);
922 * sync_Arb_IDs - synchronize APIC bus arbitration IDs
924 void __init sync_Arb_IDs(void)
927 * Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not
930 if (modern_apic() || boot_cpu_data.x86_vendor == X86_VENDOR_AMD)
936 apic_wait_icr_idle();
938 apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n");
939 apic_write(APIC_ICR, APIC_DEST_ALLINC |
940 APIC_INT_LEVELTRIG | APIC_DM_INIT);
944 * An initial setup of the virtual wire mode.
946 void __init init_bsp_APIC(void)
951 * Don't do the setup now if we have a SMP BIOS as the
952 * through-I/O-APIC virtual wire mode might be active.
954 if (smp_found_config || !cpu_has_apic)
958 * Do not trust the local APIC being empty at bootup.
965 value = apic_read(APIC_SPIV);
966 value &= ~APIC_VECTOR_MASK;
967 value |= APIC_SPIV_APIC_ENABLED;
970 /* This bit is reserved on P4/Xeon and should be cleared */
971 if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) &&
972 (boot_cpu_data.x86 == 15))
973 value &= ~APIC_SPIV_FOCUS_DISABLED;
976 value |= APIC_SPIV_FOCUS_DISABLED;
977 value |= SPURIOUS_APIC_VECTOR;
978 apic_write(APIC_SPIV, value);
981 * Set up the virtual wire mode.
983 apic_write(APIC_LVT0, APIC_DM_EXTINT);
985 if (!lapic_is_integrated()) /* 82489DX */
986 value |= APIC_LVT_LEVEL_TRIGGER;
987 apic_write(APIC_LVT1, value);
990 static void __cpuinit lapic_setup_esr(void)
992 unsigned long oldvalue, value, maxlvt;
993 if (lapic_is_integrated() && !esr_disable) {
996 * Something untraceable is creating bad interrupts on
997 * secondary quads ... for the moment, just leave the
998 * ESR disabled - we can't do anything useful with the
999 * errors anyway - mbligh
1001 printk(KERN_INFO "Leaving ESR disabled.\n");
1005 maxlvt = lapic_get_maxlvt();
1006 if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
1007 apic_write(APIC_ESR, 0);
1008 oldvalue = apic_read(APIC_ESR);
1010 /* enables sending errors */
1011 value = ERROR_APIC_VECTOR;
1012 apic_write(APIC_LVTERR, value);
1014 * spec says clear errors after enabling vector.
1017 apic_write(APIC_ESR, 0);
1018 value = apic_read(APIC_ESR);
1019 if (value != oldvalue)
1020 apic_printk(APIC_VERBOSE, "ESR value before enabling "
1021 "vector: 0x%08lx after: 0x%08lx\n",
1024 printk(KERN_INFO "No ESR for 82489DX.\n");
1030 * setup_local_APIC - setup the local APIC
1032 void __cpuinit setup_local_APIC(void)
1034 unsigned long value, integrated;
1037 /* Pound the ESR really hard over the head with a big hammer - mbligh */
1039 apic_write(APIC_ESR, 0);
1040 apic_write(APIC_ESR, 0);
1041 apic_write(APIC_ESR, 0);
1042 apic_write(APIC_ESR, 0);
1045 integrated = lapic_is_integrated();
1048 * Double-check whether this APIC is really registered.
1050 if (!apic_id_registered())
1054 * Intel recommends to set DFR, LDR and TPR before enabling
1055 * an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
1056 * document number 292116). So here it goes...
1061 * Set Task Priority to 'accept all'. We never change this
1064 value = apic_read(APIC_TASKPRI);
1065 value &= ~APIC_TPRI_MASK;
1066 apic_write(APIC_TASKPRI, value);
1069 * After a crash, we no longer service the interrupts and a pending
1070 * interrupt from previous kernel might still have ISR bit set.
1072 * Most probably by now CPU has serviced that pending interrupt and
1073 * it might not have done the ack_APIC_irq() because it thought,
1074 * interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
1075 * does not clear the ISR bit and cpu thinks it has already serivced
1076 * the interrupt. Hence a vector might get locked. It was noticed
1077 * for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
1079 for (i = APIC_ISR_NR - 1; i >= 0; i--) {
1080 value = apic_read(APIC_ISR + i*0x10);
1081 for (j = 31; j >= 0; j--) {
1088 * Now that we are all set up, enable the APIC
1090 value = apic_read(APIC_SPIV);
1091 value &= ~APIC_VECTOR_MASK;
1095 value |= APIC_SPIV_APIC_ENABLED;
1098 * Some unknown Intel IO/APIC (or APIC) errata is biting us with
1099 * certain networking cards. If high frequency interrupts are
1100 * happening on a particular IOAPIC pin, plus the IOAPIC routing
1101 * entry is masked/unmasked at a high rate as well then sooner or
1102 * later IOAPIC line gets 'stuck', no more interrupts are received
1103 * from the device. If focus CPU is disabled then the hang goes
1106 * [ This bug can be reproduced easily with a level-triggered
1107 * PCI Ne2000 networking cards and PII/PIII processors, dual
1111 * Actually disabling the focus CPU check just makes the hang less
1112 * frequent as it makes the interrupt distributon model be more
1113 * like LRU than MRU (the short-term load is more even across CPUs).
1114 * See also the comment in end_level_ioapic_irq(). --macro
1117 /* Enable focus processor (bit==0) */
1118 value &= ~APIC_SPIV_FOCUS_DISABLED;
1121 * Set spurious IRQ vector
1123 value |= SPURIOUS_APIC_VECTOR;
1124 apic_write(APIC_SPIV, value);
1127 * Set up LVT0, LVT1:
1129 * set up through-local-APIC on the BP's LINT0. This is not
1130 * strictly necessary in pure symmetric-IO mode, but sometimes
1131 * we delegate interrupts to the 8259A.
1134 * TODO: set up through-local-APIC from through-I/O-APIC? --macro
1136 value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
1137 if (!smp_processor_id() && (pic_mode || !value)) {
1138 value = APIC_DM_EXTINT;
1139 apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
1140 smp_processor_id());
1142 value = APIC_DM_EXTINT | APIC_LVT_MASKED;
1143 apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
1144 smp_processor_id());
1146 apic_write(APIC_LVT0, value);
1149 * only the BP should see the LINT1 NMI signal, obviously.
1151 if (!smp_processor_id())
1152 value = APIC_DM_NMI;
1154 value = APIC_DM_NMI | APIC_LVT_MASKED;
1155 if (!integrated) /* 82489DX */
1156 value |= APIC_LVT_LEVEL_TRIGGER;
1157 apic_write(APIC_LVT1, value);
1160 void __cpuinit end_local_APIC_setup(void)
1164 #ifdef CONFIG_X86_32
1166 /* Disable the local apic timer */
1167 value = apic_read(APIC_LVTT);
1168 value |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
1169 apic_write(APIC_LVTT, value);
1172 setup_apic_nmi_watchdog(NULL);
1177 * Detect and initialize APIC
1179 static int __init detect_init_APIC(void)
1183 /* Disabled by kernel option? */
1187 switch (boot_cpu_data.x86_vendor) {
1188 case X86_VENDOR_AMD:
1189 if ((boot_cpu_data.x86 == 6 && boot_cpu_data.x86_model > 1) ||
1190 (boot_cpu_data.x86 == 15))
1193 case X86_VENDOR_INTEL:
1194 if (boot_cpu_data.x86 == 6 || boot_cpu_data.x86 == 15 ||
1195 (boot_cpu_data.x86 == 5 && cpu_has_apic))
1202 if (!cpu_has_apic) {
1204 * Over-ride BIOS and try to enable the local APIC only if
1205 * "lapic" specified.
1207 if (!force_enable_local_apic) {
1208 printk(KERN_INFO "Local APIC disabled by BIOS -- "
1209 "you can enable it with \"lapic\"\n");
1213 * Some BIOSes disable the local APIC in the APIC_BASE
1214 * MSR. This can only be done in software for Intel P6 or later
1215 * and AMD K7 (Model > 1) or later.
1217 rdmsr(MSR_IA32_APICBASE, l, h);
1218 if (!(l & MSR_IA32_APICBASE_ENABLE)) {
1220 "Local APIC disabled by BIOS -- reenabling.\n");
1221 l &= ~MSR_IA32_APICBASE_BASE;
1222 l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE;
1223 wrmsr(MSR_IA32_APICBASE, l, h);
1224 enabled_via_apicbase = 1;
1228 * The APIC feature bit should now be enabled
1231 features = cpuid_edx(1);
1232 if (!(features & (1 << X86_FEATURE_APIC))) {
1233 printk(KERN_WARNING "Could not enable APIC!\n");
1236 set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
1237 mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
1239 /* The BIOS may have set up the APIC at some other address */
1240 rdmsr(MSR_IA32_APICBASE, l, h);
1241 if (l & MSR_IA32_APICBASE_ENABLE)
1242 mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
1244 printk(KERN_INFO "Found and enabled local APIC!\n");
1251 printk(KERN_INFO "No local APIC present or hardware disabled\n");
1256 * init_apic_mappings - initialize APIC mappings
1258 void __init init_apic_mappings(void)
1261 * If no local APIC can be found then set up a fake all
1262 * zeroes page to simulate the local APIC and another
1263 * one for the IO-APIC.
1265 if (!smp_found_config && detect_init_APIC()) {
1266 apic_phys = (unsigned long) alloc_bootmem_pages(PAGE_SIZE);
1267 apic_phys = __pa(apic_phys);
1269 apic_phys = mp_lapic_addr;
1271 set_fixmap_nocache(FIX_APIC_BASE, apic_phys);
1272 printk(KERN_DEBUG "mapped APIC to %08lx (%08lx)\n", APIC_BASE,
1276 * Fetch the APIC ID of the BSP in case we have a
1277 * default configuration (or the MP table is broken).
1279 if (boot_cpu_physical_apicid == -1U)
1280 boot_cpu_physical_apicid = read_apic_id();
1285 * This initializes the IO-APIC and APIC hardware if this is
1289 int apic_version[MAX_APICS];
1291 int __init APIC_init_uniprocessor(void)
1293 if (!smp_found_config && !cpu_has_apic)
1297 * Complain if the BIOS pretends there is one.
1299 if (!cpu_has_apic &&
1300 APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
1301 printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
1302 boot_cpu_physical_apicid);
1303 clear_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
1307 verify_local_APIC();
1312 * Hack: In case of kdump, after a crash, kernel might be booting
1313 * on a cpu with non-zero lapic id. But boot_cpu_physical_apicid
1314 * might be zero if read from MP tables. Get it from LAPIC.
1316 #ifdef CONFIG_CRASH_DUMP
1317 boot_cpu_physical_apicid = read_apic_id();
1319 physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map);
1323 #ifdef CONFIG_X86_IO_APIC
1324 if (!smp_found_config || skip_ioapic_setup || !nr_ioapics)
1326 localise_nmi_watchdog();
1327 end_local_APIC_setup();
1328 #ifdef CONFIG_X86_IO_APIC
1329 if (smp_found_config)
1330 if (!skip_ioapic_setup && nr_ioapics)
1339 * Local APIC interrupts
1343 * This interrupt should _never_ happen with our APIC/SMP architecture
1345 void smp_spurious_interrupt(struct pt_regs *regs)
1351 * Check if this really is a spurious interrupt and ACK it
1352 * if it is a vectored one. Just in case...
1353 * Spurious interrupts should not be ACKed.
1355 v = apic_read(APIC_ISR + ((SPURIOUS_APIC_VECTOR & ~0x1f) >> 1));
1356 if (v & (1 << (SPURIOUS_APIC_VECTOR & 0x1f)))
1359 /* see sw-dev-man vol 3, chapter 7.4.13.5 */
1360 printk(KERN_INFO "spurious APIC interrupt on CPU#%d, "
1361 "should never happen.\n", smp_processor_id());
1362 __get_cpu_var(irq_stat).irq_spurious_count++;
1367 * This interrupt should never happen with our APIC/SMP architecture
1369 void smp_error_interrupt(struct pt_regs *regs)
1371 unsigned long v, v1;
1374 /* First tickle the hardware, only then report what went on. -- REW */
1375 v = apic_read(APIC_ESR);
1376 apic_write(APIC_ESR, 0);
1377 v1 = apic_read(APIC_ESR);
1379 atomic_inc(&irq_err_count);
1381 /* Here is what the APIC error bits mean:
1384 2: Send accept error
1385 3: Receive accept error
1387 5: Send illegal vector
1388 6: Received illegal vector
1389 7: Illegal register address
1391 printk(KERN_DEBUG "APIC error on CPU%d: %02lx(%02lx)\n",
1392 smp_processor_id(), v , v1);
1397 * connect_bsp_APIC - attach the APIC to the interrupt system
1399 void __init connect_bsp_APIC(void)
1401 #ifdef CONFIG_X86_32
1404 * Do not trust the local APIC being empty at bootup.
1408 * PIC mode, enable APIC mode in the IMCR, i.e. connect BSP's
1409 * local APIC to INT and NMI lines.
1411 apic_printk(APIC_VERBOSE, "leaving PIC mode, "
1412 "enabling APIC mode.\n");
1421 * disconnect_bsp_APIC - detach the APIC from the interrupt system
1422 * @virt_wire_setup: indicates, whether virtual wire mode is selected
1424 * Virtual wire mode is necessary to deliver legacy interrupts even when the
1427 void disconnect_bsp_APIC(int virt_wire_setup)
1429 #ifdef CONFIG_X86_32
1432 * Put the board back into PIC mode (has an effect only on
1433 * certain older boards). Note that APIC interrupts, including
1434 * IPIs, won't work beyond this point! The only exception are
1437 apic_printk(APIC_VERBOSE, "disabling APIC mode, "
1438 "entering PIC mode.\n");
1445 /* Go back to Virtual Wire compatibility mode */
1448 /* For the spurious interrupt use vector F, and enable it */
1449 value = apic_read(APIC_SPIV);
1450 value &= ~APIC_VECTOR_MASK;
1451 value |= APIC_SPIV_APIC_ENABLED;
1453 apic_write(APIC_SPIV, value);
1455 if (!virt_wire_setup) {
1457 * For LVT0 make it edge triggered, active high,
1458 * external and enabled
1460 value = apic_read(APIC_LVT0);
1461 value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
1462 APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
1463 APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
1464 value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
1465 value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
1466 apic_write(APIC_LVT0, value);
1469 apic_write(APIC_LVT0, APIC_LVT_MASKED);
1473 * For LVT1 make it edge triggered, active high,
1476 value = apic_read(APIC_LVT1);
1477 value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
1478 APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
1479 APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
1480 value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
1481 value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
1482 apic_write(APIC_LVT1, value);
1485 void __cpuinit generic_processor_info(int apicid, int version)
1493 if (version == 0x0) {
1494 printk(KERN_WARNING "BIOS bug, APIC version is 0 for CPU#%d! "
1495 "fixing up to 0x10. (tell your hw vendor)\n",
1499 apic_version[apicid] = version;
1501 if (num_processors >= NR_CPUS) {
1502 printk(KERN_WARNING "WARNING: NR_CPUS limit of %i reached."
1503 " Processor ignored.\n", NR_CPUS);
1507 if (num_processors >= maxcpus) {
1508 printk(KERN_WARNING "WARNING: maxcpus limit of %i reached."
1509 " Processor ignored.\n", maxcpus);
1514 cpus_complement(tmp_map, cpu_present_map);
1515 cpu = first_cpu(tmp_map);
1517 physid_set(apicid, phys_cpu_present_map);
1518 if (apicid == boot_cpu_physical_apicid) {
1520 * x86_bios_cpu_apicid is required to have processors listed
1521 * in same order as logical cpu numbers. Hence the first
1522 * entry is BSP, and so on.
1526 if (apicid > max_physical_apicid)
1527 max_physical_apicid = apicid;
1529 #ifdef CONFIG_X86_32
1531 * Would be preferable to switch to bigsmp when CONFIG_HOTPLUG_CPU=y
1532 * but we need to work other dependencies like SMP_SUSPEND etc
1533 * before this can be done without some confusion.
1534 * if (CPU_HOTPLUG_ENABLED || num_processors > 8)
1535 * - Ashok Raj <ashok.raj@intel.com>
1537 if (max_physical_apicid >= 8) {
1538 switch (boot_cpu_data.x86_vendor) {
1539 case X86_VENDOR_INTEL:
1540 if (!APIC_XAPIC(version)) {
1544 /* If P4 and above fall through */
1545 case X86_VENDOR_AMD:
1551 #if defined(CONFIG_X86_SMP) || defined(CONFIG_X86_64)
1552 /* are we being called early in kernel startup? */
1553 if (early_per_cpu_ptr(x86_cpu_to_apicid)) {
1554 u16 *cpu_to_apicid = early_per_cpu_ptr(x86_cpu_to_apicid);
1555 u16 *bios_cpu_apicid = early_per_cpu_ptr(x86_bios_cpu_apicid);
1557 cpu_to_apicid[cpu] = apicid;
1558 bios_cpu_apicid[cpu] = apicid;
1560 per_cpu(x86_cpu_to_apicid, cpu) = apicid;
1561 per_cpu(x86_bios_cpu_apicid, cpu) = apicid;
1565 cpu_set(cpu, cpu_possible_map);
1566 cpu_set(cpu, cpu_present_map);
1576 * 'active' is true if the local APIC was enabled by us and
1577 * not the BIOS; this signifies that we are also responsible
1578 * for disabling it before entering apm/acpi suspend
1581 /* r/w apic fields */
1582 unsigned int apic_id;
1583 unsigned int apic_taskpri;
1584 unsigned int apic_ldr;
1585 unsigned int apic_dfr;
1586 unsigned int apic_spiv;
1587 unsigned int apic_lvtt;
1588 unsigned int apic_lvtpc;
1589 unsigned int apic_lvt0;
1590 unsigned int apic_lvt1;
1591 unsigned int apic_lvterr;
1592 unsigned int apic_tmict;
1593 unsigned int apic_tdcr;
1594 unsigned int apic_thmr;
1597 static int lapic_suspend(struct sys_device *dev, pm_message_t state)
1599 unsigned long flags;
1602 if (!apic_pm_state.active)
1605 maxlvt = lapic_get_maxlvt();
1607 apic_pm_state.apic_id = apic_read(APIC_ID);
1608 apic_pm_state.apic_taskpri = apic_read(APIC_TASKPRI);
1609 apic_pm_state.apic_ldr = apic_read(APIC_LDR);
1610 apic_pm_state.apic_dfr = apic_read(APIC_DFR);
1611 apic_pm_state.apic_spiv = apic_read(APIC_SPIV);
1612 apic_pm_state.apic_lvtt = apic_read(APIC_LVTT);
1614 apic_pm_state.apic_lvtpc = apic_read(APIC_LVTPC);
1615 apic_pm_state.apic_lvt0 = apic_read(APIC_LVT0);
1616 apic_pm_state.apic_lvt1 = apic_read(APIC_LVT1);
1617 apic_pm_state.apic_lvterr = apic_read(APIC_LVTERR);
1618 apic_pm_state.apic_tmict = apic_read(APIC_TMICT);
1619 apic_pm_state.apic_tdcr = apic_read(APIC_TDCR);
1620 #if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL)
1622 apic_pm_state.apic_thmr = apic_read(APIC_LVTTHMR);
1625 local_irq_save(flags);
1626 disable_local_APIC();
1627 local_irq_restore(flags);
1631 static int lapic_resume(struct sys_device *dev)
1634 unsigned long flags;
1637 if (!apic_pm_state.active)
1640 maxlvt = lapic_get_maxlvt();
1642 local_irq_save(flags);
1644 #ifdef CONFIG_X86_64
1650 * Make sure the APICBASE points to the right address
1652 * FIXME! This will be wrong if we ever support suspend on
1653 * SMP! We'll need to do this as part of the CPU restore!
1655 rdmsr(MSR_IA32_APICBASE, l, h);
1656 l &= ~MSR_IA32_APICBASE_BASE;
1657 l |= MSR_IA32_APICBASE_ENABLE | mp_lapic_addr;
1658 wrmsr(MSR_IA32_APICBASE, l, h);
1660 apic_write(APIC_LVTERR, ERROR_APIC_VECTOR | APIC_LVT_MASKED);
1661 apic_write(APIC_ID, apic_pm_state.apic_id);
1662 apic_write(APIC_DFR, apic_pm_state.apic_dfr);
1663 apic_write(APIC_LDR, apic_pm_state.apic_ldr);
1664 apic_write(APIC_TASKPRI, apic_pm_state.apic_taskpri);
1665 apic_write(APIC_SPIV, apic_pm_state.apic_spiv);
1666 apic_write(APIC_LVT0, apic_pm_state.apic_lvt0);
1667 apic_write(APIC_LVT1, apic_pm_state.apic_lvt1);
1668 #if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL)
1670 apic_write(APIC_LVTTHMR, apic_pm_state.apic_thmr);
1673 apic_write(APIC_LVTPC, apic_pm_state.apic_lvtpc);
1674 apic_write(APIC_LVTT, apic_pm_state.apic_lvtt);
1675 apic_write(APIC_TDCR, apic_pm_state.apic_tdcr);
1676 apic_write(APIC_TMICT, apic_pm_state.apic_tmict);
1677 apic_write(APIC_ESR, 0);
1678 apic_read(APIC_ESR);
1679 apic_write(APIC_LVTERR, apic_pm_state.apic_lvterr);
1680 apic_write(APIC_ESR, 0);
1681 apic_read(APIC_ESR);
1683 local_irq_restore(flags);
1689 * This device has no shutdown method - fully functioning local APICs
1690 * are needed on every CPU up until machine_halt/restart/poweroff.
1693 static struct sysdev_class lapic_sysclass = {
1695 .resume = lapic_resume,
1696 .suspend = lapic_suspend,
1699 static struct sys_device device_lapic = {
1701 .cls = &lapic_sysclass,
1704 static void __devinit apic_pm_activate(void)
1706 apic_pm_state.active = 1;
1709 static int __init init_lapic_sysfs(void)
1715 /* XXX: remove suspend/resume procs if !apic_pm_state.active? */
1717 error = sysdev_class_register(&lapic_sysclass);
1719 error = sysdev_register(&device_lapic);
1722 device_initcall(init_lapic_sysfs);
1724 #else /* CONFIG_PM */
1726 static void apic_pm_activate(void) { }
1728 #endif /* CONFIG_PM */
1731 * APIC command line parameters
1733 static int __init parse_lapic(char *arg)
1735 force_enable_local_apic = 1;
1738 early_param("lapic", parse_lapic);
1740 static int __init setup_disableapic(char *arg)
1743 setup_clear_cpu_cap(X86_FEATURE_APIC);
1746 early_param("disableapic", setup_disableapic);
1748 /* same as disableapic, for compatibility */
1749 static int __init setup_nolapic(char *arg)
1751 return setup_disableapic(arg);
1753 early_param("nolapic", setup_nolapic);
1755 static int __init parse_disable_apic_timer(char *arg)
1757 disable_apic_timer = 1;
1760 early_param("noapictimer", parse_disable_apic_timer);
1762 static int __init parse_nolapic_timer(char *arg)
1764 disable_apic_timer = 1;
1767 early_param("nolapic_timer", parse_nolapic_timer);
1769 static int __init parse_lapic_timer_c2_ok(char *arg)
1771 local_apic_timer_c2_ok = 1;
1774 early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok);
1776 static int __init apic_set_verbosity(char *arg)
1779 #ifdef CONFIG_X86_64
1780 skip_ioapic_setup = 0;
1787 if (strcmp("debug", arg) == 0)
1788 apic_verbosity = APIC_DEBUG;
1789 else if (strcmp("verbose", arg) == 0)
1790 apic_verbosity = APIC_VERBOSE;
1792 printk(KERN_WARNING "APIC Verbosity level %s not recognised"
1793 " use apic=verbose or apic=debug\n", arg);
1799 early_param("apic", apic_set_verbosity);
1801 static int __init lapic_insert_resource(void)
1806 /* Put local APIC into the resource map. */
1807 lapic_resource.start = apic_phys;
1808 lapic_resource.end = lapic_resource.start + PAGE_SIZE - 1;
1809 insert_resource(&iomem_resource, &lapic_resource);
1815 * need call insert after e820_reserve_resources()
1816 * that is using request_resource
1818 late_initcall(lapic_insert_resource);