1 /************************************************************************
2 * s2io.c: A Linux PCI-X Ethernet driver for Neterion 10GbE Server NIC
3 * Copyright(c) 2002-2007 Neterion Inc.
5 * This software may be used and distributed according to the terms of
6 * the GNU General Public License (GPL), incorporated herein by reference.
7 * Drivers based on or derived from this code fall under the GPL and must
8 * retain the authorship, copyright and license notice. This file is not
9 * a complete program and may only be used when the entire operating
10 * system is licensed under the GPL.
11 * See the file COPYING in this distribution for more information.
14 * Jeff Garzik : For pointing out the improper error condition
15 * check in the s2io_xmit routine and also some
16 * issues in the Tx watch dog function. Also for
17 * patiently answering all those innumerable
18 * questions regaring the 2.6 porting issues.
19 * Stephen Hemminger : Providing proper 2.6 porting mechanism for some
20 * macros available only in 2.6 Kernel.
21 * Francois Romieu : For pointing out all code part that were
22 * deprecated and also styling related comments.
23 * Grant Grundler : For helping me get rid of some Architecture
25 * Christopher Hellwig : Some more 2.6 specific issues in the driver.
27 * The module loadable parameters that are supported by the driver and a brief
28 * explaination of all the variables.
30 * rx_ring_num : This can be used to program the number of receive rings used
32 * rx_ring_sz: This defines the number of receive blocks each ring can have.
33 * This is also an array of size 8.
34 * rx_ring_mode: This defines the operation mode of all 8 rings. The valid
36 * tx_fifo_num: This defines the number of Tx FIFOs thats used int the driver.
37 * tx_fifo_len: This too is an array of 8. Each element defines the number of
38 * Tx descriptors that can be associated with each corresponding FIFO.
39 * intr_type: This defines the type of interrupt. The values can be 0(INTA),
40 * 2(MSI_X). Default value is '2(MSI_X)'
41 * lro_enable: Specifies whether to enable Large Receive Offload (LRO) or not.
42 * Possible values '1' for enable '0' for disable. Default is '0'
43 * lro_max_pkts: This parameter defines maximum number of packets can be
44 * aggregated as a single large packet
45 * napi: This parameter used to enable/disable NAPI (polling Rx)
46 * Possible values '1' for enable and '0' for disable. Default is '1'
47 * ufo: This parameter used to enable/disable UDP Fragmentation Offload(UFO)
48 * Possible values '1' for enable and '0' for disable. Default is '0'
49 * vlan_tag_strip: This can be used to enable or disable vlan stripping.
50 * Possible values '1' for enable , '0' for disable.
51 * Default is '2' - which means disable in promisc mode
52 * and enable in non-promiscuous mode.
53 * multiq: This parameter used to enable/disable MULTIQUEUE support.
54 * Possible values '1' for enable and '0' for disable. Default is '0'
55 ************************************************************************/
57 #include <linux/module.h>
58 #include <linux/types.h>
59 #include <linux/errno.h>
60 #include <linux/ioport.h>
61 #include <linux/pci.h>
62 #include <linux/dma-mapping.h>
63 #include <linux/kernel.h>
64 #include <linux/netdevice.h>
65 #include <linux/etherdevice.h>
66 #include <linux/skbuff.h>
67 #include <linux/init.h>
68 #include <linux/delay.h>
69 #include <linux/stddef.h>
70 #include <linux/ioctl.h>
71 #include <linux/timex.h>
72 #include <linux/ethtool.h>
73 #include <linux/workqueue.h>
74 #include <linux/if_vlan.h>
76 #include <linux/tcp.h>
79 #include <asm/system.h>
80 #include <asm/uaccess.h>
82 #include <asm/div64.h>
87 #include "s2io-regs.h"
89 #define DRV_VERSION "2.0.26.19"
91 /* S2io Driver name & version. */
92 static char s2io_driver_name[] = "Neterion";
93 static char s2io_driver_version[] = DRV_VERSION;
95 static int rxd_size[2] = {32,48};
96 static int rxd_count[2] = {127,85};
98 static inline int RXD_IS_UP2DT(struct RxD_t *rxdp)
102 ret = ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
103 (GET_RXD_MARKER(rxdp->Control_2) != THE_RXD_MARK));
109 * Cards with following subsystem_id have a link state indication
110 * problem, 600B, 600C, 600D, 640B, 640C and 640D.
111 * macro below identifies these cards given the subsystem_id.
113 #define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \
114 (dev_type == XFRAME_I_DEVICE) ? \
115 ((((subid >= 0x600B) && (subid <= 0x600D)) || \
116 ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0
118 #define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \
119 ADAPTER_STATUS_RMAC_LOCAL_FAULT)))
120 #define TASKLET_IN_USE test_and_set_bit(0, (&sp->tasklet_status))
123 static inline int rx_buffer_level(struct s2io_nic * sp, int rxb_size, int ring)
125 struct mac_info *mac_control;
127 mac_control = &sp->mac_control;
128 if (rxb_size <= rxd_count[sp->rxd_mode])
130 else if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16)
135 static inline int is_s2io_card_up(const struct s2io_nic * sp)
137 return test_bit(__S2IO_STATE_CARD_UP, &sp->state);
140 /* Ethtool related variables and Macros. */
141 static char s2io_gstrings[][ETH_GSTRING_LEN] = {
142 "Register test\t(offline)",
143 "Eeprom test\t(offline)",
144 "Link test\t(online)",
145 "RLDRAM test\t(offline)",
146 "BIST Test\t(offline)"
149 static char ethtool_xena_stats_keys[][ETH_GSTRING_LEN] = {
151 {"tmac_data_octets"},
155 {"tmac_pause_ctrl_frms"},
159 {"tmac_any_err_frms"},
160 {"tmac_ttl_less_fb_octets"},
161 {"tmac_vld_ip_octets"},
169 {"rmac_data_octets"},
170 {"rmac_fcs_err_frms"},
172 {"rmac_vld_mcst_frms"},
173 {"rmac_vld_bcst_frms"},
174 {"rmac_in_rng_len_err_frms"},
175 {"rmac_out_rng_len_err_frms"},
177 {"rmac_pause_ctrl_frms"},
178 {"rmac_unsup_ctrl_frms"},
180 {"rmac_accepted_ucst_frms"},
181 {"rmac_accepted_nucst_frms"},
182 {"rmac_discarded_frms"},
183 {"rmac_drop_events"},
184 {"rmac_ttl_less_fb_octets"},
186 {"rmac_usized_frms"},
187 {"rmac_osized_frms"},
189 {"rmac_jabber_frms"},
190 {"rmac_ttl_64_frms"},
191 {"rmac_ttl_65_127_frms"},
192 {"rmac_ttl_128_255_frms"},
193 {"rmac_ttl_256_511_frms"},
194 {"rmac_ttl_512_1023_frms"},
195 {"rmac_ttl_1024_1518_frms"},
203 {"rmac_err_drp_udp"},
204 {"rmac_xgmii_err_sym"},
222 {"rmac_xgmii_data_err_cnt"},
223 {"rmac_xgmii_ctrl_err_cnt"},
224 {"rmac_accepted_ip"},
228 {"new_rd_req_rtry_cnt"},
230 {"wr_rtry_rd_ack_cnt"},
233 {"new_wr_req_rtry_cnt"},
236 {"rd_rtry_wr_ack_cnt"},
246 static char ethtool_enhanced_stats_keys[][ETH_GSTRING_LEN] = {
247 {"rmac_ttl_1519_4095_frms"},
248 {"rmac_ttl_4096_8191_frms"},
249 {"rmac_ttl_8192_max_frms"},
250 {"rmac_ttl_gt_max_frms"},
251 {"rmac_osized_alt_frms"},
252 {"rmac_jabber_alt_frms"},
253 {"rmac_gt_max_alt_frms"},
255 {"rmac_len_discard"},
256 {"rmac_fcs_discard"},
259 {"rmac_red_discard"},
260 {"rmac_rts_discard"},
261 {"rmac_ingm_full_discard"},
265 static char ethtool_driver_stats_keys[][ETH_GSTRING_LEN] = {
266 {"\n DRIVER STATISTICS"},
267 {"single_bit_ecc_errs"},
268 {"double_bit_ecc_errs"},
281 {"alarm_transceiver_temp_high"},
282 {"alarm_transceiver_temp_low"},
283 {"alarm_laser_bias_current_high"},
284 {"alarm_laser_bias_current_low"},
285 {"alarm_laser_output_power_high"},
286 {"alarm_laser_output_power_low"},
287 {"warn_transceiver_temp_high"},
288 {"warn_transceiver_temp_low"},
289 {"warn_laser_bias_current_high"},
290 {"warn_laser_bias_current_low"},
291 {"warn_laser_output_power_high"},
292 {"warn_laser_output_power_low"},
293 {"lro_aggregated_pkts"},
294 {"lro_flush_both_count"},
295 {"lro_out_of_sequence_pkts"},
296 {"lro_flush_due_to_max_pkts"},
297 {"lro_avg_aggr_pkts"},
298 {"mem_alloc_fail_cnt"},
299 {"pci_map_fail_cnt"},
300 {"watchdog_timer_cnt"},
307 {"tx_tcode_buf_abort_cnt"},
308 {"tx_tcode_desc_abort_cnt"},
309 {"tx_tcode_parity_err_cnt"},
310 {"tx_tcode_link_loss_cnt"},
311 {"tx_tcode_list_proc_err_cnt"},
312 {"rx_tcode_parity_err_cnt"},
313 {"rx_tcode_abort_cnt"},
314 {"rx_tcode_parity_abort_cnt"},
315 {"rx_tcode_rda_fail_cnt"},
316 {"rx_tcode_unkn_prot_cnt"},
317 {"rx_tcode_fcs_err_cnt"},
318 {"rx_tcode_buf_size_err_cnt"},
319 {"rx_tcode_rxd_corrupt_cnt"},
320 {"rx_tcode_unkn_err_cnt"},
328 {"mac_tmac_err_cnt"},
329 {"mac_rmac_err_cnt"},
330 {"xgxs_txgxs_err_cnt"},
331 {"xgxs_rxgxs_err_cnt"},
333 {"prc_pcix_err_cnt"},
340 #define S2IO_XENA_STAT_LEN ARRAY_SIZE(ethtool_xena_stats_keys)
341 #define S2IO_ENHANCED_STAT_LEN ARRAY_SIZE(ethtool_enhanced_stats_keys)
342 #define S2IO_DRIVER_STAT_LEN ARRAY_SIZE(ethtool_driver_stats_keys)
344 #define XFRAME_I_STAT_LEN (S2IO_XENA_STAT_LEN + S2IO_DRIVER_STAT_LEN )
345 #define XFRAME_II_STAT_LEN (XFRAME_I_STAT_LEN + S2IO_ENHANCED_STAT_LEN )
347 #define XFRAME_I_STAT_STRINGS_LEN ( XFRAME_I_STAT_LEN * ETH_GSTRING_LEN )
348 #define XFRAME_II_STAT_STRINGS_LEN ( XFRAME_II_STAT_LEN * ETH_GSTRING_LEN )
350 #define S2IO_TEST_LEN ARRAY_SIZE(s2io_gstrings)
351 #define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN
353 #define S2IO_TIMER_CONF(timer, handle, arg, exp) \
354 init_timer(&timer); \
355 timer.function = handle; \
356 timer.data = (unsigned long) arg; \
357 mod_timer(&timer, (jiffies + exp)) \
359 /* copy mac addr to def_mac_addr array */
360 static void do_s2io_copy_mac_addr(struct s2io_nic *sp, int offset, u64 mac_addr)
362 sp->def_mac_addr[offset].mac_addr[5] = (u8) (mac_addr);
363 sp->def_mac_addr[offset].mac_addr[4] = (u8) (mac_addr >> 8);
364 sp->def_mac_addr[offset].mac_addr[3] = (u8) (mac_addr >> 16);
365 sp->def_mac_addr[offset].mac_addr[2] = (u8) (mac_addr >> 24);
366 sp->def_mac_addr[offset].mac_addr[1] = (u8) (mac_addr >> 32);
367 sp->def_mac_addr[offset].mac_addr[0] = (u8) (mac_addr >> 40);
370 static void s2io_vlan_rx_register(struct net_device *dev,
371 struct vlan_group *grp)
374 struct s2io_nic *nic = dev->priv;
375 unsigned long flags[MAX_TX_FIFOS];
376 struct mac_info *mac_control = &nic->mac_control;
377 struct config_param *config = &nic->config;
379 for (i = 0; i < config->tx_fifo_num; i++)
380 spin_lock_irqsave(&mac_control->fifos[i].tx_lock, flags[i]);
383 for (i = config->tx_fifo_num - 1; i >= 0; i--)
384 spin_unlock_irqrestore(&mac_control->fifos[i].tx_lock,
388 /* A flag indicating whether 'RX_PA_CFG_STRIP_VLAN_TAG' bit is set or not */
389 static int vlan_strip_flag;
391 /* Unregister the vlan */
392 static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid)
395 struct s2io_nic *nic = dev->priv;
396 unsigned long flags[MAX_TX_FIFOS];
397 struct mac_info *mac_control = &nic->mac_control;
398 struct config_param *config = &nic->config;
400 for (i = 0; i < config->tx_fifo_num; i++)
401 spin_lock_irqsave(&mac_control->fifos[i].tx_lock, flags[i]);
404 vlan_group_set_device(nic->vlgrp, vid, NULL);
406 for (i = config->tx_fifo_num - 1; i >= 0; i--)
407 spin_unlock_irqrestore(&mac_control->fifos[i].tx_lock,
412 * Constants to be programmed into the Xena's registers, to configure
417 static const u64 herc_act_dtx_cfg[] = {
419 0x8000051536750000ULL, 0x80000515367500E0ULL,
421 0x8000051536750004ULL, 0x80000515367500E4ULL,
423 0x80010515003F0000ULL, 0x80010515003F00E0ULL,
425 0x80010515003F0004ULL, 0x80010515003F00E4ULL,
427 0x801205150D440000ULL, 0x801205150D4400E0ULL,
429 0x801205150D440004ULL, 0x801205150D4400E4ULL,
431 0x80020515F2100000ULL, 0x80020515F21000E0ULL,
433 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
438 static const u64 xena_dtx_cfg[] = {
440 0x8000051500000000ULL, 0x80000515000000E0ULL,
442 0x80000515D9350004ULL, 0x80000515D93500E4ULL,
444 0x8001051500000000ULL, 0x80010515000000E0ULL,
446 0x80010515001E0004ULL, 0x80010515001E00E4ULL,
448 0x8002051500000000ULL, 0x80020515000000E0ULL,
450 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
455 * Constants for Fixing the MacAddress problem seen mostly on
458 static const u64 fix_mac[] = {
459 0x0060000000000000ULL, 0x0060600000000000ULL,
460 0x0040600000000000ULL, 0x0000600000000000ULL,
461 0x0020600000000000ULL, 0x0060600000000000ULL,
462 0x0020600000000000ULL, 0x0060600000000000ULL,
463 0x0020600000000000ULL, 0x0060600000000000ULL,
464 0x0020600000000000ULL, 0x0060600000000000ULL,
465 0x0020600000000000ULL, 0x0060600000000000ULL,
466 0x0020600000000000ULL, 0x0060600000000000ULL,
467 0x0020600000000000ULL, 0x0060600000000000ULL,
468 0x0020600000000000ULL, 0x0060600000000000ULL,
469 0x0020600000000000ULL, 0x0060600000000000ULL,
470 0x0020600000000000ULL, 0x0060600000000000ULL,
471 0x0020600000000000ULL, 0x0000600000000000ULL,
472 0x0040600000000000ULL, 0x0060600000000000ULL,
476 MODULE_LICENSE("GPL");
477 MODULE_VERSION(DRV_VERSION);
480 /* Module Loadable parameters. */
481 S2IO_PARM_INT(tx_fifo_num, FIFO_DEFAULT_NUM);
482 S2IO_PARM_INT(rx_ring_num, 1);
483 S2IO_PARM_INT(multiq, 0);
484 S2IO_PARM_INT(rx_ring_mode, 1);
485 S2IO_PARM_INT(use_continuous_tx_intrs, 1);
486 S2IO_PARM_INT(rmac_pause_time, 0x100);
487 S2IO_PARM_INT(mc_pause_threshold_q0q3, 187);
488 S2IO_PARM_INT(mc_pause_threshold_q4q7, 187);
489 S2IO_PARM_INT(shared_splits, 0);
490 S2IO_PARM_INT(tmac_util_period, 5);
491 S2IO_PARM_INT(rmac_util_period, 5);
492 S2IO_PARM_INT(l3l4hdr_size, 128);
493 /* 0 is no steering, 1 is Priority steering, 2 is Default steering */
494 S2IO_PARM_INT(tx_steering_type, TX_DEFAULT_STEERING);
495 /* Frequency of Rx desc syncs expressed as power of 2 */
496 S2IO_PARM_INT(rxsync_frequency, 3);
497 /* Interrupt type. Values can be 0(INTA), 2(MSI_X) */
498 S2IO_PARM_INT(intr_type, 2);
499 /* Large receive offload feature */
500 static unsigned int lro_enable;
501 module_param_named(lro, lro_enable, uint, 0);
503 /* Max pkts to be aggregated by LRO at one time. If not specified,
504 * aggregation happens until we hit max IP pkt size(64K)
506 S2IO_PARM_INT(lro_max_pkts, 0xFFFF);
507 S2IO_PARM_INT(indicate_max_pkts, 0);
509 S2IO_PARM_INT(napi, 1);
510 S2IO_PARM_INT(ufo, 0);
511 S2IO_PARM_INT(vlan_tag_strip, NO_STRIP_IN_PROMISC);
513 static unsigned int tx_fifo_len[MAX_TX_FIFOS] =
514 {DEFAULT_FIFO_0_LEN, [1 ...(MAX_TX_FIFOS - 1)] = DEFAULT_FIFO_1_7_LEN};
515 static unsigned int rx_ring_sz[MAX_RX_RINGS] =
516 {[0 ...(MAX_RX_RINGS - 1)] = SMALL_BLK_CNT};
517 static unsigned int rts_frm_len[MAX_RX_RINGS] =
518 {[0 ...(MAX_RX_RINGS - 1)] = 0 };
520 module_param_array(tx_fifo_len, uint, NULL, 0);
521 module_param_array(rx_ring_sz, uint, NULL, 0);
522 module_param_array(rts_frm_len, uint, NULL, 0);
526 * This table lists all the devices that this driver supports.
528 static struct pci_device_id s2io_tbl[] __devinitdata = {
529 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_WIN,
530 PCI_ANY_ID, PCI_ANY_ID},
531 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_UNI,
532 PCI_ANY_ID, PCI_ANY_ID},
533 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_WIN,
534 PCI_ANY_ID, PCI_ANY_ID},
535 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI,
536 PCI_ANY_ID, PCI_ANY_ID},
540 MODULE_DEVICE_TABLE(pci, s2io_tbl);
542 static struct pci_error_handlers s2io_err_handler = {
543 .error_detected = s2io_io_error_detected,
544 .slot_reset = s2io_io_slot_reset,
545 .resume = s2io_io_resume,
548 static struct pci_driver s2io_driver = {
550 .id_table = s2io_tbl,
551 .probe = s2io_init_nic,
552 .remove = __devexit_p(s2io_rem_nic),
553 .err_handler = &s2io_err_handler,
556 /* A simplifier macro used both by init and free shared_mem Fns(). */
557 #define TXD_MEM_PAGE_CNT(len, per_each) ((len+per_each - 1) / per_each)
559 /* netqueue manipulation helper functions */
560 static inline void s2io_stop_all_tx_queue(struct s2io_nic *sp)
563 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
564 if (sp->config.multiq) {
565 for (i = 0; i < sp->config.tx_fifo_num; i++)
566 netif_stop_subqueue(sp->dev, i);
570 for (i = 0; i < sp->config.tx_fifo_num; i++)
571 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_STOP;
572 netif_stop_queue(sp->dev);
576 static inline void s2io_stop_tx_queue(struct s2io_nic *sp, int fifo_no)
578 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
579 if (sp->config.multiq)
580 netif_stop_subqueue(sp->dev, fifo_no);
584 sp->mac_control.fifos[fifo_no].queue_state =
586 netif_stop_queue(sp->dev);
590 static inline void s2io_start_all_tx_queue(struct s2io_nic *sp)
593 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
594 if (sp->config.multiq) {
595 for (i = 0; i < sp->config.tx_fifo_num; i++)
596 netif_start_subqueue(sp->dev, i);
600 for (i = 0; i < sp->config.tx_fifo_num; i++)
601 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_START;
602 netif_start_queue(sp->dev);
606 static inline void s2io_start_tx_queue(struct s2io_nic *sp, int fifo_no)
608 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
609 if (sp->config.multiq)
610 netif_start_subqueue(sp->dev, fifo_no);
614 sp->mac_control.fifos[fifo_no].queue_state =
616 netif_start_queue(sp->dev);
620 static inline void s2io_wake_all_tx_queue(struct s2io_nic *sp)
623 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
624 if (sp->config.multiq) {
625 for (i = 0; i < sp->config.tx_fifo_num; i++)
626 netif_wake_subqueue(sp->dev, i);
630 for (i = 0; i < sp->config.tx_fifo_num; i++)
631 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_START;
632 netif_wake_queue(sp->dev);
636 static inline void s2io_wake_tx_queue(
637 struct fifo_info *fifo, int cnt, u8 multiq)
640 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
642 if (cnt && __netif_subqueue_stopped(fifo->dev, fifo->fifo_no))
643 netif_wake_subqueue(fifo->dev, fifo->fifo_no);
646 if (cnt && (fifo->queue_state == FIFO_QUEUE_STOP)) {
647 if (netif_queue_stopped(fifo->dev)) {
648 fifo->queue_state = FIFO_QUEUE_START;
649 netif_wake_queue(fifo->dev);
655 * init_shared_mem - Allocation and Initialization of Memory
656 * @nic: Device private variable.
657 * Description: The function allocates all the memory areas shared
658 * between the NIC and the driver. This includes Tx descriptors,
659 * Rx descriptors and the statistics block.
662 static int init_shared_mem(struct s2io_nic *nic)
665 void *tmp_v_addr, *tmp_v_addr_next;
666 dma_addr_t tmp_p_addr, tmp_p_addr_next;
667 struct RxD_block *pre_rxd_blk = NULL;
669 int lst_size, lst_per_page;
670 struct net_device *dev = nic->dev;
674 struct mac_info *mac_control;
675 struct config_param *config;
676 unsigned long long mem_allocated = 0;
678 mac_control = &nic->mac_control;
679 config = &nic->config;
682 /* Allocation and initialization of TXDLs in FIOFs */
684 for (i = 0; i < config->tx_fifo_num; i++) {
685 size += config->tx_cfg[i].fifo_len;
687 if (size > MAX_AVAILABLE_TXDS) {
688 DBG_PRINT(ERR_DBG, "s2io: Requested TxDs too high, ");
689 DBG_PRINT(ERR_DBG, "Requested: %d, max supported: 8192\n", size);
694 for (i = 0; i < config->tx_fifo_num; i++) {
695 size = config->tx_cfg[i].fifo_len;
697 * Legal values are from 2 to 8192
700 DBG_PRINT(ERR_DBG, "s2io: Invalid fifo len (%d)", size);
701 DBG_PRINT(ERR_DBG, "for fifo %d\n", i);
702 DBG_PRINT(ERR_DBG, "s2io: Legal values for fifo len"
708 lst_size = (sizeof(struct TxD) * config->max_txds);
709 lst_per_page = PAGE_SIZE / lst_size;
711 for (i = 0; i < config->tx_fifo_num; i++) {
712 int fifo_len = config->tx_cfg[i].fifo_len;
713 int list_holder_size = fifo_len * sizeof(struct list_info_hold);
714 mac_control->fifos[i].list_info = kzalloc(list_holder_size,
716 if (!mac_control->fifos[i].list_info) {
718 "Malloc failed for list_info\n");
721 mem_allocated += list_holder_size;
723 for (i = 0; i < config->tx_fifo_num; i++) {
724 int page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
726 mac_control->fifos[i].tx_curr_put_info.offset = 0;
727 mac_control->fifos[i].tx_curr_put_info.fifo_len =
728 config->tx_cfg[i].fifo_len - 1;
729 mac_control->fifos[i].tx_curr_get_info.offset = 0;
730 mac_control->fifos[i].tx_curr_get_info.fifo_len =
731 config->tx_cfg[i].fifo_len - 1;
732 mac_control->fifos[i].fifo_no = i;
733 mac_control->fifos[i].nic = nic;
734 mac_control->fifos[i].max_txds = MAX_SKB_FRAGS + 2;
735 mac_control->fifos[i].dev = dev;
737 for (j = 0; j < page_num; j++) {
741 tmp_v = pci_alloc_consistent(nic->pdev,
745 "pci_alloc_consistent ");
746 DBG_PRINT(INFO_DBG, "failed for TxDL\n");
749 /* If we got a zero DMA address(can happen on
750 * certain platforms like PPC), reallocate.
751 * Store virtual address of page we don't want,
755 mac_control->zerodma_virt_addr = tmp_v;
757 "%s: Zero DMA address for TxDL. ", dev->name);
759 "Virtual address %p\n", tmp_v);
760 tmp_v = pci_alloc_consistent(nic->pdev,
764 "pci_alloc_consistent ");
765 DBG_PRINT(INFO_DBG, "failed for TxDL\n");
768 mem_allocated += PAGE_SIZE;
770 while (k < lst_per_page) {
771 int l = (j * lst_per_page) + k;
772 if (l == config->tx_cfg[i].fifo_len)
774 mac_control->fifos[i].list_info[l].list_virt_addr =
775 tmp_v + (k * lst_size);
776 mac_control->fifos[i].list_info[l].list_phy_addr =
777 tmp_p + (k * lst_size);
783 for (i = 0; i < config->tx_fifo_num; i++) {
784 size = config->tx_cfg[i].fifo_len;
785 mac_control->fifos[i].ufo_in_band_v
786 = kcalloc(size, sizeof(u64), GFP_KERNEL);
787 if (!mac_control->fifos[i].ufo_in_band_v)
789 mem_allocated += (size * sizeof(u64));
792 /* Allocation and initialization of RXDs in Rings */
794 for (i = 0; i < config->rx_ring_num; i++) {
795 if (config->rx_cfg[i].num_rxd %
796 (rxd_count[nic->rxd_mode] + 1)) {
797 DBG_PRINT(ERR_DBG, "%s: RxD count of ", dev->name);
798 DBG_PRINT(ERR_DBG, "Ring%d is not a multiple of ",
800 DBG_PRINT(ERR_DBG, "RxDs per Block");
803 size += config->rx_cfg[i].num_rxd;
804 mac_control->rings[i].block_count =
805 config->rx_cfg[i].num_rxd /
806 (rxd_count[nic->rxd_mode] + 1 );
807 mac_control->rings[i].pkt_cnt = config->rx_cfg[i].num_rxd -
808 mac_control->rings[i].block_count;
810 if (nic->rxd_mode == RXD_MODE_1)
811 size = (size * (sizeof(struct RxD1)));
813 size = (size * (sizeof(struct RxD3)));
815 for (i = 0; i < config->rx_ring_num; i++) {
816 mac_control->rings[i].rx_curr_get_info.block_index = 0;
817 mac_control->rings[i].rx_curr_get_info.offset = 0;
818 mac_control->rings[i].rx_curr_get_info.ring_len =
819 config->rx_cfg[i].num_rxd - 1;
820 mac_control->rings[i].rx_curr_put_info.block_index = 0;
821 mac_control->rings[i].rx_curr_put_info.offset = 0;
822 mac_control->rings[i].rx_curr_put_info.ring_len =
823 config->rx_cfg[i].num_rxd - 1;
824 mac_control->rings[i].nic = nic;
825 mac_control->rings[i].ring_no = i;
827 blk_cnt = config->rx_cfg[i].num_rxd /
828 (rxd_count[nic->rxd_mode] + 1);
829 /* Allocating all the Rx blocks */
830 for (j = 0; j < blk_cnt; j++) {
831 struct rx_block_info *rx_blocks;
834 rx_blocks = &mac_control->rings[i].rx_blocks[j];
835 size = SIZE_OF_BLOCK; //size is always page size
836 tmp_v_addr = pci_alloc_consistent(nic->pdev, size,
838 if (tmp_v_addr == NULL) {
840 * In case of failure, free_shared_mem()
841 * is called, which should free any
842 * memory that was alloced till the
845 rx_blocks->block_virt_addr = tmp_v_addr;
848 mem_allocated += size;
849 memset(tmp_v_addr, 0, size);
850 rx_blocks->block_virt_addr = tmp_v_addr;
851 rx_blocks->block_dma_addr = tmp_p_addr;
852 rx_blocks->rxds = kmalloc(sizeof(struct rxd_info)*
853 rxd_count[nic->rxd_mode],
855 if (!rx_blocks->rxds)
858 (sizeof(struct rxd_info)* rxd_count[nic->rxd_mode]);
859 for (l=0; l<rxd_count[nic->rxd_mode];l++) {
860 rx_blocks->rxds[l].virt_addr =
861 rx_blocks->block_virt_addr +
862 (rxd_size[nic->rxd_mode] * l);
863 rx_blocks->rxds[l].dma_addr =
864 rx_blocks->block_dma_addr +
865 (rxd_size[nic->rxd_mode] * l);
868 /* Interlinking all Rx Blocks */
869 for (j = 0; j < blk_cnt; j++) {
871 mac_control->rings[i].rx_blocks[j].block_virt_addr;
873 mac_control->rings[i].rx_blocks[(j + 1) %
874 blk_cnt].block_virt_addr;
876 mac_control->rings[i].rx_blocks[j].block_dma_addr;
878 mac_control->rings[i].rx_blocks[(j + 1) %
879 blk_cnt].block_dma_addr;
881 pre_rxd_blk = (struct RxD_block *) tmp_v_addr;
882 pre_rxd_blk->reserved_2_pNext_RxD_block =
883 (unsigned long) tmp_v_addr_next;
884 pre_rxd_blk->pNext_RxD_Blk_physical =
885 (u64) tmp_p_addr_next;
888 if (nic->rxd_mode == RXD_MODE_3B) {
890 * Allocation of Storages for buffer addresses in 2BUFF mode
891 * and the buffers as well.
893 for (i = 0; i < config->rx_ring_num; i++) {
894 blk_cnt = config->rx_cfg[i].num_rxd /
895 (rxd_count[nic->rxd_mode]+ 1);
896 mac_control->rings[i].ba =
897 kmalloc((sizeof(struct buffAdd *) * blk_cnt),
899 if (!mac_control->rings[i].ba)
901 mem_allocated +=(sizeof(struct buffAdd *) * blk_cnt);
902 for (j = 0; j < blk_cnt; j++) {
904 mac_control->rings[i].ba[j] =
905 kmalloc((sizeof(struct buffAdd) *
906 (rxd_count[nic->rxd_mode] + 1)),
908 if (!mac_control->rings[i].ba[j])
910 mem_allocated += (sizeof(struct buffAdd) * \
911 (rxd_count[nic->rxd_mode] + 1));
912 while (k != rxd_count[nic->rxd_mode]) {
913 ba = &mac_control->rings[i].ba[j][k];
915 ba->ba_0_org = (void *) kmalloc
916 (BUF0_LEN + ALIGN_SIZE, GFP_KERNEL);
920 (BUF0_LEN + ALIGN_SIZE);
921 tmp = (unsigned long)ba->ba_0_org;
923 tmp &= ~((unsigned long) ALIGN_SIZE);
924 ba->ba_0 = (void *) tmp;
926 ba->ba_1_org = (void *) kmalloc
927 (BUF1_LEN + ALIGN_SIZE, GFP_KERNEL);
931 += (BUF1_LEN + ALIGN_SIZE);
932 tmp = (unsigned long) ba->ba_1_org;
934 tmp &= ~((unsigned long) ALIGN_SIZE);
935 ba->ba_1 = (void *) tmp;
942 /* Allocation and initialization of Statistics block */
943 size = sizeof(struct stat_block);
944 mac_control->stats_mem = pci_alloc_consistent
945 (nic->pdev, size, &mac_control->stats_mem_phy);
947 if (!mac_control->stats_mem) {
949 * In case of failure, free_shared_mem() is called, which
950 * should free any memory that was alloced till the
955 mem_allocated += size;
956 mac_control->stats_mem_sz = size;
958 tmp_v_addr = mac_control->stats_mem;
959 mac_control->stats_info = (struct stat_block *) tmp_v_addr;
960 memset(tmp_v_addr, 0, size);
961 DBG_PRINT(INIT_DBG, "%s:Ring Mem PHY: 0x%llx\n", dev->name,
962 (unsigned long long) tmp_p_addr);
963 mac_control->stats_info->sw_stat.mem_allocated += mem_allocated;
968 * free_shared_mem - Free the allocated Memory
969 * @nic: Device private variable.
970 * Description: This function is to free all memory locations allocated by
971 * the init_shared_mem() function and return it to the kernel.
974 static void free_shared_mem(struct s2io_nic *nic)
976 int i, j, blk_cnt, size;
978 dma_addr_t tmp_p_addr;
979 struct mac_info *mac_control;
980 struct config_param *config;
981 int lst_size, lst_per_page;
982 struct net_device *dev;
990 mac_control = &nic->mac_control;
991 config = &nic->config;
993 lst_size = (sizeof(struct TxD) * config->max_txds);
994 lst_per_page = PAGE_SIZE / lst_size;
996 for (i = 0; i < config->tx_fifo_num; i++) {
997 page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
999 for (j = 0; j < page_num; j++) {
1000 int mem_blks = (j * lst_per_page);
1001 if (!mac_control->fifos[i].list_info)
1003 if (!mac_control->fifos[i].list_info[mem_blks].
1006 pci_free_consistent(nic->pdev, PAGE_SIZE,
1007 mac_control->fifos[i].
1008 list_info[mem_blks].
1010 mac_control->fifos[i].
1011 list_info[mem_blks].
1013 nic->mac_control.stats_info->sw_stat.mem_freed
1016 /* If we got a zero DMA address during allocation,
1019 if (mac_control->zerodma_virt_addr) {
1020 pci_free_consistent(nic->pdev, PAGE_SIZE,
1021 mac_control->zerodma_virt_addr,
1024 "%s: Freeing TxDL with zero DMA addr. ",
1026 DBG_PRINT(INIT_DBG, "Virtual address %p\n",
1027 mac_control->zerodma_virt_addr);
1028 nic->mac_control.stats_info->sw_stat.mem_freed
1031 kfree(mac_control->fifos[i].list_info);
1032 nic->mac_control.stats_info->sw_stat.mem_freed +=
1033 (nic->config.tx_cfg[i].fifo_len *sizeof(struct list_info_hold));
1036 size = SIZE_OF_BLOCK;
1037 for (i = 0; i < config->rx_ring_num; i++) {
1038 blk_cnt = mac_control->rings[i].block_count;
1039 for (j = 0; j < blk_cnt; j++) {
1040 tmp_v_addr = mac_control->rings[i].rx_blocks[j].
1042 tmp_p_addr = mac_control->rings[i].rx_blocks[j].
1044 if (tmp_v_addr == NULL)
1046 pci_free_consistent(nic->pdev, size,
1047 tmp_v_addr, tmp_p_addr);
1048 nic->mac_control.stats_info->sw_stat.mem_freed += size;
1049 kfree(mac_control->rings[i].rx_blocks[j].rxds);
1050 nic->mac_control.stats_info->sw_stat.mem_freed +=
1051 ( sizeof(struct rxd_info)* rxd_count[nic->rxd_mode]);
1055 if (nic->rxd_mode == RXD_MODE_3B) {
1056 /* Freeing buffer storage addresses in 2BUFF mode. */
1057 for (i = 0; i < config->rx_ring_num; i++) {
1058 blk_cnt = config->rx_cfg[i].num_rxd /
1059 (rxd_count[nic->rxd_mode] + 1);
1060 for (j = 0; j < blk_cnt; j++) {
1062 if (!mac_control->rings[i].ba[j])
1064 while (k != rxd_count[nic->rxd_mode]) {
1065 struct buffAdd *ba =
1066 &mac_control->rings[i].ba[j][k];
1067 kfree(ba->ba_0_org);
1068 nic->mac_control.stats_info->sw_stat.\
1069 mem_freed += (BUF0_LEN + ALIGN_SIZE);
1070 kfree(ba->ba_1_org);
1071 nic->mac_control.stats_info->sw_stat.\
1072 mem_freed += (BUF1_LEN + ALIGN_SIZE);
1075 kfree(mac_control->rings[i].ba[j]);
1076 nic->mac_control.stats_info->sw_stat.mem_freed +=
1077 (sizeof(struct buffAdd) *
1078 (rxd_count[nic->rxd_mode] + 1));
1080 kfree(mac_control->rings[i].ba);
1081 nic->mac_control.stats_info->sw_stat.mem_freed +=
1082 (sizeof(struct buffAdd *) * blk_cnt);
1086 for (i = 0; i < nic->config.tx_fifo_num; i++) {
1087 if (mac_control->fifos[i].ufo_in_band_v) {
1088 nic->mac_control.stats_info->sw_stat.mem_freed
1089 += (config->tx_cfg[i].fifo_len * sizeof(u64));
1090 kfree(mac_control->fifos[i].ufo_in_band_v);
1094 if (mac_control->stats_mem) {
1095 nic->mac_control.stats_info->sw_stat.mem_freed +=
1096 mac_control->stats_mem_sz;
1097 pci_free_consistent(nic->pdev,
1098 mac_control->stats_mem_sz,
1099 mac_control->stats_mem,
1100 mac_control->stats_mem_phy);
1105 * s2io_verify_pci_mode -
1108 static int s2io_verify_pci_mode(struct s2io_nic *nic)
1110 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1111 register u64 val64 = 0;
1114 val64 = readq(&bar0->pci_mode);
1115 mode = (u8)GET_PCI_MODE(val64);
1117 if ( val64 & PCI_MODE_UNKNOWN_MODE)
1118 return -1; /* Unknown PCI mode */
1122 #define NEC_VENID 0x1033
1123 #define NEC_DEVID 0x0125
1124 static int s2io_on_nec_bridge(struct pci_dev *s2io_pdev)
1126 struct pci_dev *tdev = NULL;
1127 while ((tdev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, tdev)) != NULL) {
1128 if (tdev->vendor == NEC_VENID && tdev->device == NEC_DEVID) {
1129 if (tdev->bus == s2io_pdev->bus->parent)
1137 static int bus_speed[8] = {33, 133, 133, 200, 266, 133, 200, 266};
1139 * s2io_print_pci_mode -
1141 static int s2io_print_pci_mode(struct s2io_nic *nic)
1143 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1144 register u64 val64 = 0;
1146 struct config_param *config = &nic->config;
1148 val64 = readq(&bar0->pci_mode);
1149 mode = (u8)GET_PCI_MODE(val64);
1151 if ( val64 & PCI_MODE_UNKNOWN_MODE)
1152 return -1; /* Unknown PCI mode */
1154 config->bus_speed = bus_speed[mode];
1156 if (s2io_on_nec_bridge(nic->pdev)) {
1157 DBG_PRINT(ERR_DBG, "%s: Device is on PCI-E bus\n",
1162 if (val64 & PCI_MODE_32_BITS) {
1163 DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
1165 DBG_PRINT(ERR_DBG, "%s: Device is on 64 bit ", nic->dev->name);
1169 case PCI_MODE_PCI_33:
1170 DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
1172 case PCI_MODE_PCI_66:
1173 DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
1175 case PCI_MODE_PCIX_M1_66:
1176 DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
1178 case PCI_MODE_PCIX_M1_100:
1179 DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
1181 case PCI_MODE_PCIX_M1_133:
1182 DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
1184 case PCI_MODE_PCIX_M2_66:
1185 DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
1187 case PCI_MODE_PCIX_M2_100:
1188 DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
1190 case PCI_MODE_PCIX_M2_133:
1191 DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
1194 return -1; /* Unsupported bus speed */
1201 * init_tti - Initialization transmit traffic interrupt scheme
1202 * @nic: device private variable
1203 * @link: link status (UP/DOWN) used to enable/disable continuous
1204 * transmit interrupts
1205 * Description: The function configures transmit traffic interrupts
1206 * Return Value: SUCCESS on success and
1210 static int init_tti(struct s2io_nic *nic, int link)
1212 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1213 register u64 val64 = 0;
1215 struct config_param *config;
1217 config = &nic->config;
1219 for (i = 0; i < config->tx_fifo_num; i++) {
1221 * TTI Initialization. Default Tx timer gets us about
1222 * 250 interrupts per sec. Continuous interrupts are enabled
1225 if (nic->device_type == XFRAME_II_DEVICE) {
1226 int count = (nic->config.bus_speed * 125)/2;
1227 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count);
1229 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078);
1231 val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) |
1232 TTI_DATA1_MEM_TX_URNG_B(0x10) |
1233 TTI_DATA1_MEM_TX_URNG_C(0x30) |
1234 TTI_DATA1_MEM_TX_TIMER_AC_EN;
1236 if (use_continuous_tx_intrs && (link == LINK_UP))
1237 val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
1238 writeq(val64, &bar0->tti_data1_mem);
1240 val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
1241 TTI_DATA2_MEM_TX_UFC_B(0x20) |
1242 TTI_DATA2_MEM_TX_UFC_C(0x40) |
1243 TTI_DATA2_MEM_TX_UFC_D(0x80);
1245 writeq(val64, &bar0->tti_data2_mem);
1247 val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD |
1248 TTI_CMD_MEM_OFFSET(i);
1249 writeq(val64, &bar0->tti_command_mem);
1251 if (wait_for_cmd_complete(&bar0->tti_command_mem,
1252 TTI_CMD_MEM_STROBE_NEW_CMD, S2IO_BIT_RESET) != SUCCESS)
1260 * init_nic - Initialization of hardware
1261 * @nic: device private variable
1262 * Description: The function sequentially configures every block
1263 * of the H/W from their reset values.
1264 * Return Value: SUCCESS on success and
1265 * '-1' on failure (endian settings incorrect).
1268 static int init_nic(struct s2io_nic *nic)
1270 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1271 struct net_device *dev = nic->dev;
1272 register u64 val64 = 0;
1276 struct mac_info *mac_control;
1277 struct config_param *config;
1279 unsigned long long mem_share;
1282 mac_control = &nic->mac_control;
1283 config = &nic->config;
1285 /* to set the swapper controle on the card */
1286 if(s2io_set_swapper(nic)) {
1287 DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n");
1292 * Herc requires EOI to be removed from reset before XGXS, so..
1294 if (nic->device_type & XFRAME_II_DEVICE) {
1295 val64 = 0xA500000000ULL;
1296 writeq(val64, &bar0->sw_reset);
1298 val64 = readq(&bar0->sw_reset);
1301 /* Remove XGXS from reset state */
1303 writeq(val64, &bar0->sw_reset);
1305 val64 = readq(&bar0->sw_reset);
1307 /* Ensure that it's safe to access registers by checking
1308 * RIC_RUNNING bit is reset. Check is valid only for XframeII.
1310 if (nic->device_type == XFRAME_II_DEVICE) {
1311 for (i = 0; i < 50; i++) {
1312 val64 = readq(&bar0->adapter_status);
1313 if (!(val64 & ADAPTER_STATUS_RIC_RUNNING))
1321 /* Enable Receiving broadcasts */
1322 add = &bar0->mac_cfg;
1323 val64 = readq(&bar0->mac_cfg);
1324 val64 |= MAC_RMAC_BCAST_ENABLE;
1325 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1326 writel((u32) val64, add);
1327 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1328 writel((u32) (val64 >> 32), (add + 4));
1330 /* Read registers in all blocks */
1331 val64 = readq(&bar0->mac_int_mask);
1332 val64 = readq(&bar0->mc_int_mask);
1333 val64 = readq(&bar0->xgxs_int_mask);
1337 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
1339 if (nic->device_type & XFRAME_II_DEVICE) {
1340 while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
1341 SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
1342 &bar0->dtx_control, UF);
1344 msleep(1); /* Necessary!! */
1348 while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
1349 SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
1350 &bar0->dtx_control, UF);
1351 val64 = readq(&bar0->dtx_control);
1356 /* Tx DMA Initialization */
1358 writeq(val64, &bar0->tx_fifo_partition_0);
1359 writeq(val64, &bar0->tx_fifo_partition_1);
1360 writeq(val64, &bar0->tx_fifo_partition_2);
1361 writeq(val64, &bar0->tx_fifo_partition_3);
1364 for (i = 0, j = 0; i < config->tx_fifo_num; i++) {
1366 vBIT(config->tx_cfg[i].fifo_len - 1, ((j * 32) + 19),
1367 13) | vBIT(config->tx_cfg[i].fifo_priority,
1370 if (i == (config->tx_fifo_num - 1)) {
1377 writeq(val64, &bar0->tx_fifo_partition_0);
1382 writeq(val64, &bar0->tx_fifo_partition_1);
1387 writeq(val64, &bar0->tx_fifo_partition_2);
1392 writeq(val64, &bar0->tx_fifo_partition_3);
1403 * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug
1404 * SXE-008 TRANSMIT DMA ARBITRATION ISSUE.
1406 if ((nic->device_type == XFRAME_I_DEVICE) &&
1407 (nic->pdev->revision < 4))
1408 writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable);
1410 val64 = readq(&bar0->tx_fifo_partition_0);
1411 DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n",
1412 &bar0->tx_fifo_partition_0, (unsigned long long) val64);
1415 * Initialization of Tx_PA_CONFIG register to ignore packet
1416 * integrity checking.
1418 val64 = readq(&bar0->tx_pa_cfg);
1419 val64 |= TX_PA_CFG_IGNORE_FRM_ERR | TX_PA_CFG_IGNORE_SNAP_OUI |
1420 TX_PA_CFG_IGNORE_LLC_CTRL | TX_PA_CFG_IGNORE_L2_ERR;
1421 writeq(val64, &bar0->tx_pa_cfg);
1423 /* Rx DMA intialization. */
1425 for (i = 0; i < config->rx_ring_num; i++) {
1427 vBIT(config->rx_cfg[i].ring_priority, (5 + (i * 8)),
1430 writeq(val64, &bar0->rx_queue_priority);
1433 * Allocating equal share of memory to all the
1437 if (nic->device_type & XFRAME_II_DEVICE)
1442 for (i = 0; i < config->rx_ring_num; i++) {
1445 mem_share = (mem_size / config->rx_ring_num +
1446 mem_size % config->rx_ring_num);
1447 val64 |= RX_QUEUE_CFG_Q0_SZ(mem_share);
1450 mem_share = (mem_size / config->rx_ring_num);
1451 val64 |= RX_QUEUE_CFG_Q1_SZ(mem_share);
1454 mem_share = (mem_size / config->rx_ring_num);
1455 val64 |= RX_QUEUE_CFG_Q2_SZ(mem_share);
1458 mem_share = (mem_size / config->rx_ring_num);
1459 val64 |= RX_QUEUE_CFG_Q3_SZ(mem_share);
1462 mem_share = (mem_size / config->rx_ring_num);
1463 val64 |= RX_QUEUE_CFG_Q4_SZ(mem_share);
1466 mem_share = (mem_size / config->rx_ring_num);
1467 val64 |= RX_QUEUE_CFG_Q5_SZ(mem_share);
1470 mem_share = (mem_size / config->rx_ring_num);
1471 val64 |= RX_QUEUE_CFG_Q6_SZ(mem_share);
1474 mem_share = (mem_size / config->rx_ring_num);
1475 val64 |= RX_QUEUE_CFG_Q7_SZ(mem_share);
1479 writeq(val64, &bar0->rx_queue_cfg);
1482 * Filling Tx round robin registers
1483 * as per the number of FIFOs for equal scheduling priority
1485 switch (config->tx_fifo_num) {
1488 writeq(val64, &bar0->tx_w_round_robin_0);
1489 writeq(val64, &bar0->tx_w_round_robin_1);
1490 writeq(val64, &bar0->tx_w_round_robin_2);
1491 writeq(val64, &bar0->tx_w_round_robin_3);
1492 writeq(val64, &bar0->tx_w_round_robin_4);
1495 val64 = 0x0001000100010001ULL;
1496 writeq(val64, &bar0->tx_w_round_robin_0);
1497 writeq(val64, &bar0->tx_w_round_robin_1);
1498 writeq(val64, &bar0->tx_w_round_robin_2);
1499 writeq(val64, &bar0->tx_w_round_robin_3);
1500 val64 = 0x0001000100000000ULL;
1501 writeq(val64, &bar0->tx_w_round_robin_4);
1504 val64 = 0x0001020001020001ULL;
1505 writeq(val64, &bar0->tx_w_round_robin_0);
1506 val64 = 0x0200010200010200ULL;
1507 writeq(val64, &bar0->tx_w_round_robin_1);
1508 val64 = 0x0102000102000102ULL;
1509 writeq(val64, &bar0->tx_w_round_robin_2);
1510 val64 = 0x0001020001020001ULL;
1511 writeq(val64, &bar0->tx_w_round_robin_3);
1512 val64 = 0x0200010200000000ULL;
1513 writeq(val64, &bar0->tx_w_round_robin_4);
1516 val64 = 0x0001020300010203ULL;
1517 writeq(val64, &bar0->tx_w_round_robin_0);
1518 writeq(val64, &bar0->tx_w_round_robin_1);
1519 writeq(val64, &bar0->tx_w_round_robin_2);
1520 writeq(val64, &bar0->tx_w_round_robin_3);
1521 val64 = 0x0001020300000000ULL;
1522 writeq(val64, &bar0->tx_w_round_robin_4);
1525 val64 = 0x0001020304000102ULL;
1526 writeq(val64, &bar0->tx_w_round_robin_0);
1527 val64 = 0x0304000102030400ULL;
1528 writeq(val64, &bar0->tx_w_round_robin_1);
1529 val64 = 0x0102030400010203ULL;
1530 writeq(val64, &bar0->tx_w_round_robin_2);
1531 val64 = 0x0400010203040001ULL;
1532 writeq(val64, &bar0->tx_w_round_robin_3);
1533 val64 = 0x0203040000000000ULL;
1534 writeq(val64, &bar0->tx_w_round_robin_4);
1537 val64 = 0x0001020304050001ULL;
1538 writeq(val64, &bar0->tx_w_round_robin_0);
1539 val64 = 0x0203040500010203ULL;
1540 writeq(val64, &bar0->tx_w_round_robin_1);
1541 val64 = 0x0405000102030405ULL;
1542 writeq(val64, &bar0->tx_w_round_robin_2);
1543 val64 = 0x0001020304050001ULL;
1544 writeq(val64, &bar0->tx_w_round_robin_3);
1545 val64 = 0x0203040500000000ULL;
1546 writeq(val64, &bar0->tx_w_round_robin_4);
1549 val64 = 0x0001020304050600ULL;
1550 writeq(val64, &bar0->tx_w_round_robin_0);
1551 val64 = 0x0102030405060001ULL;
1552 writeq(val64, &bar0->tx_w_round_robin_1);
1553 val64 = 0x0203040506000102ULL;
1554 writeq(val64, &bar0->tx_w_round_robin_2);
1555 val64 = 0x0304050600010203ULL;
1556 writeq(val64, &bar0->tx_w_round_robin_3);
1557 val64 = 0x0405060000000000ULL;
1558 writeq(val64, &bar0->tx_w_round_robin_4);
1561 val64 = 0x0001020304050607ULL;
1562 writeq(val64, &bar0->tx_w_round_robin_0);
1563 writeq(val64, &bar0->tx_w_round_robin_1);
1564 writeq(val64, &bar0->tx_w_round_robin_2);
1565 writeq(val64, &bar0->tx_w_round_robin_3);
1566 val64 = 0x0001020300000000ULL;
1567 writeq(val64, &bar0->tx_w_round_robin_4);
1571 /* Enable all configured Tx FIFO partitions */
1572 val64 = readq(&bar0->tx_fifo_partition_0);
1573 val64 |= (TX_FIFO_PARTITION_EN);
1574 writeq(val64, &bar0->tx_fifo_partition_0);
1576 /* Filling the Rx round robin registers as per the
1577 * number of Rings and steering based on QoS.
1579 switch (config->rx_ring_num) {
1581 val64 = 0x8080808080808080ULL;
1582 writeq(val64, &bar0->rts_qos_steering);
1585 val64 = 0x0000010000010000ULL;
1586 writeq(val64, &bar0->rx_w_round_robin_0);
1587 val64 = 0x0100000100000100ULL;
1588 writeq(val64, &bar0->rx_w_round_robin_1);
1589 val64 = 0x0001000001000001ULL;
1590 writeq(val64, &bar0->rx_w_round_robin_2);
1591 val64 = 0x0000010000010000ULL;
1592 writeq(val64, &bar0->rx_w_round_robin_3);
1593 val64 = 0x0100000000000000ULL;
1594 writeq(val64, &bar0->rx_w_round_robin_4);
1596 val64 = 0x8080808040404040ULL;
1597 writeq(val64, &bar0->rts_qos_steering);
1600 val64 = 0x0001000102000001ULL;
1601 writeq(val64, &bar0->rx_w_round_robin_0);
1602 val64 = 0x0001020000010001ULL;
1603 writeq(val64, &bar0->rx_w_round_robin_1);
1604 val64 = 0x0200000100010200ULL;
1605 writeq(val64, &bar0->rx_w_round_robin_2);
1606 val64 = 0x0001000102000001ULL;
1607 writeq(val64, &bar0->rx_w_round_robin_3);
1608 val64 = 0x0001020000000000ULL;
1609 writeq(val64, &bar0->rx_w_round_robin_4);
1611 val64 = 0x8080804040402020ULL;
1612 writeq(val64, &bar0->rts_qos_steering);
1615 val64 = 0x0001020300010200ULL;
1616 writeq(val64, &bar0->rx_w_round_robin_0);
1617 val64 = 0x0100000102030001ULL;
1618 writeq(val64, &bar0->rx_w_round_robin_1);
1619 val64 = 0x0200010000010203ULL;
1620 writeq(val64, &bar0->rx_w_round_robin_2);
1621 val64 = 0x0001020001000001ULL;
1622 writeq(val64, &bar0->rx_w_round_robin_3);
1623 val64 = 0x0203000100000000ULL;
1624 writeq(val64, &bar0->rx_w_round_robin_4);
1626 val64 = 0x8080404020201010ULL;
1627 writeq(val64, &bar0->rts_qos_steering);
1630 val64 = 0x0001000203000102ULL;
1631 writeq(val64, &bar0->rx_w_round_robin_0);
1632 val64 = 0x0001020001030004ULL;
1633 writeq(val64, &bar0->rx_w_round_robin_1);
1634 val64 = 0x0001000203000102ULL;
1635 writeq(val64, &bar0->rx_w_round_robin_2);
1636 val64 = 0x0001020001030004ULL;
1637 writeq(val64, &bar0->rx_w_round_robin_3);
1638 val64 = 0x0001000000000000ULL;
1639 writeq(val64, &bar0->rx_w_round_robin_4);
1641 val64 = 0x8080404020201008ULL;
1642 writeq(val64, &bar0->rts_qos_steering);
1645 val64 = 0x0001020304000102ULL;
1646 writeq(val64, &bar0->rx_w_round_robin_0);
1647 val64 = 0x0304050001020001ULL;
1648 writeq(val64, &bar0->rx_w_round_robin_1);
1649 val64 = 0x0203000100000102ULL;
1650 writeq(val64, &bar0->rx_w_round_robin_2);
1651 val64 = 0x0304000102030405ULL;
1652 writeq(val64, &bar0->rx_w_round_robin_3);
1653 val64 = 0x0001000200000000ULL;
1654 writeq(val64, &bar0->rx_w_round_robin_4);
1656 val64 = 0x8080404020100804ULL;
1657 writeq(val64, &bar0->rts_qos_steering);
1660 val64 = 0x0001020001020300ULL;
1661 writeq(val64, &bar0->rx_w_round_robin_0);
1662 val64 = 0x0102030400010203ULL;
1663 writeq(val64, &bar0->rx_w_round_robin_1);
1664 val64 = 0x0405060001020001ULL;
1665 writeq(val64, &bar0->rx_w_round_robin_2);
1666 val64 = 0x0304050000010200ULL;
1667 writeq(val64, &bar0->rx_w_round_robin_3);
1668 val64 = 0x0102030000000000ULL;
1669 writeq(val64, &bar0->rx_w_round_robin_4);
1671 val64 = 0x8080402010080402ULL;
1672 writeq(val64, &bar0->rts_qos_steering);
1675 val64 = 0x0001020300040105ULL;
1676 writeq(val64, &bar0->rx_w_round_robin_0);
1677 val64 = 0x0200030106000204ULL;
1678 writeq(val64, &bar0->rx_w_round_robin_1);
1679 val64 = 0x0103000502010007ULL;
1680 writeq(val64, &bar0->rx_w_round_robin_2);
1681 val64 = 0x0304010002060500ULL;
1682 writeq(val64, &bar0->rx_w_round_robin_3);
1683 val64 = 0x0103020400000000ULL;
1684 writeq(val64, &bar0->rx_w_round_robin_4);
1686 val64 = 0x8040201008040201ULL;
1687 writeq(val64, &bar0->rts_qos_steering);
1693 for (i = 0; i < 8; i++)
1694 writeq(val64, &bar0->rts_frm_len_n[i]);
1696 /* Set the default rts frame length for the rings configured */
1697 val64 = MAC_RTS_FRM_LEN_SET(dev->mtu+22);
1698 for (i = 0 ; i < config->rx_ring_num ; i++)
1699 writeq(val64, &bar0->rts_frm_len_n[i]);
1701 /* Set the frame length for the configured rings
1702 * desired by the user
1704 for (i = 0; i < config->rx_ring_num; i++) {
1705 /* If rts_frm_len[i] == 0 then it is assumed that user not
1706 * specified frame length steering.
1707 * If the user provides the frame length then program
1708 * the rts_frm_len register for those values or else
1709 * leave it as it is.
1711 if (rts_frm_len[i] != 0) {
1712 writeq(MAC_RTS_FRM_LEN_SET(rts_frm_len[i]),
1713 &bar0->rts_frm_len_n[i]);
1717 /* Disable differentiated services steering logic */
1718 for (i = 0; i < 64; i++) {
1719 if (rts_ds_steer(nic, i, 0) == FAILURE) {
1720 DBG_PRINT(ERR_DBG, "%s: failed rts ds steering",
1722 DBG_PRINT(ERR_DBG, "set on codepoint %d\n", i);
1727 /* Program statistics memory */
1728 writeq(mac_control->stats_mem_phy, &bar0->stat_addr);
1730 if (nic->device_type == XFRAME_II_DEVICE) {
1731 val64 = STAT_BC(0x320);
1732 writeq(val64, &bar0->stat_byte_cnt);
1736 * Initializing the sampling rate for the device to calculate the
1737 * bandwidth utilization.
1739 val64 = MAC_TX_LINK_UTIL_VAL(tmac_util_period) |
1740 MAC_RX_LINK_UTIL_VAL(rmac_util_period);
1741 writeq(val64, &bar0->mac_link_util);
1744 * Initializing the Transmit and Receive Traffic Interrupt
1748 /* Initialize TTI */
1749 if (SUCCESS != init_tti(nic, nic->last_link_state))
1752 /* RTI Initialization */
1753 if (nic->device_type == XFRAME_II_DEVICE) {
1755 * Programmed to generate Apprx 500 Intrs per
1758 int count = (nic->config.bus_speed * 125)/4;
1759 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count);
1761 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF);
1762 val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) |
1763 RTI_DATA1_MEM_RX_URNG_B(0x10) |
1764 RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN;
1766 writeq(val64, &bar0->rti_data1_mem);
1768 val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) |
1769 RTI_DATA2_MEM_RX_UFC_B(0x2) ;
1770 if (nic->config.intr_type == MSI_X)
1771 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x20) | \
1772 RTI_DATA2_MEM_RX_UFC_D(0x40));
1774 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x40) | \
1775 RTI_DATA2_MEM_RX_UFC_D(0x80));
1776 writeq(val64, &bar0->rti_data2_mem);
1778 for (i = 0; i < config->rx_ring_num; i++) {
1779 val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD
1780 | RTI_CMD_MEM_OFFSET(i);
1781 writeq(val64, &bar0->rti_command_mem);
1784 * Once the operation completes, the Strobe bit of the
1785 * command register will be reset. We poll for this
1786 * particular condition. We wait for a maximum of 500ms
1787 * for the operation to complete, if it's not complete
1788 * by then we return error.
1792 val64 = readq(&bar0->rti_command_mem);
1793 if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD))
1797 DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n",
1807 * Initializing proper values as Pause threshold into all
1808 * the 8 Queues on Rx side.
1810 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q0q3);
1811 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7);
1813 /* Disable RMAC PAD STRIPPING */
1814 add = &bar0->mac_cfg;
1815 val64 = readq(&bar0->mac_cfg);
1816 val64 &= ~(MAC_CFG_RMAC_STRIP_PAD);
1817 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1818 writel((u32) (val64), add);
1819 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1820 writel((u32) (val64 >> 32), (add + 4));
1821 val64 = readq(&bar0->mac_cfg);
1823 /* Enable FCS stripping by adapter */
1824 add = &bar0->mac_cfg;
1825 val64 = readq(&bar0->mac_cfg);
1826 val64 |= MAC_CFG_RMAC_STRIP_FCS;
1827 if (nic->device_type == XFRAME_II_DEVICE)
1828 writeq(val64, &bar0->mac_cfg);
1830 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1831 writel((u32) (val64), add);
1832 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1833 writel((u32) (val64 >> 32), (add + 4));
1837 * Set the time value to be inserted in the pause frame
1838 * generated by xena.
1840 val64 = readq(&bar0->rmac_pause_cfg);
1841 val64 &= ~(RMAC_PAUSE_HG_PTIME(0xffff));
1842 val64 |= RMAC_PAUSE_HG_PTIME(nic->mac_control.rmac_pause_time);
1843 writeq(val64, &bar0->rmac_pause_cfg);
1846 * Set the Threshold Limit for Generating the pause frame
1847 * If the amount of data in any Queue exceeds ratio of
1848 * (mac_control.mc_pause_threshold_q0q3 or q4q7)/256
1849 * pause frame is generated
1852 for (i = 0; i < 4; i++) {
1854 (((u64) 0xFF00 | nic->mac_control.
1855 mc_pause_threshold_q0q3)
1858 writeq(val64, &bar0->mc_pause_thresh_q0q3);
1861 for (i = 0; i < 4; i++) {
1863 (((u64) 0xFF00 | nic->mac_control.
1864 mc_pause_threshold_q4q7)
1867 writeq(val64, &bar0->mc_pause_thresh_q4q7);
1870 * TxDMA will stop Read request if the number of read split has
1871 * exceeded the limit pointed by shared_splits
1873 val64 = readq(&bar0->pic_control);
1874 val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits);
1875 writeq(val64, &bar0->pic_control);
1877 if (nic->config.bus_speed == 266) {
1878 writeq(TXREQTO_VAL(0x7f) | TXREQTO_EN, &bar0->txreqtimeout);
1879 writeq(0x0, &bar0->read_retry_delay);
1880 writeq(0x0, &bar0->write_retry_delay);
1884 * Programming the Herc to split every write transaction
1885 * that does not start on an ADB to reduce disconnects.
1887 if (nic->device_type == XFRAME_II_DEVICE) {
1888 val64 = FAULT_BEHAVIOUR | EXT_REQ_EN |
1889 MISC_LINK_STABILITY_PRD(3);
1890 writeq(val64, &bar0->misc_control);
1891 val64 = readq(&bar0->pic_control2);
1892 val64 &= ~(s2BIT(13)|s2BIT(14)|s2BIT(15));
1893 writeq(val64, &bar0->pic_control2);
1895 if (strstr(nic->product_name, "CX4")) {
1896 val64 = TMAC_AVG_IPG(0x17);
1897 writeq(val64, &bar0->tmac_avg_ipg);
1902 #define LINK_UP_DOWN_INTERRUPT 1
1903 #define MAC_RMAC_ERR_TIMER 2
1905 static int s2io_link_fault_indication(struct s2io_nic *nic)
1907 if (nic->config.intr_type != INTA)
1908 return MAC_RMAC_ERR_TIMER;
1909 if (nic->device_type == XFRAME_II_DEVICE)
1910 return LINK_UP_DOWN_INTERRUPT;
1912 return MAC_RMAC_ERR_TIMER;
1916 * do_s2io_write_bits - update alarm bits in alarm register
1917 * @value: alarm bits
1918 * @flag: interrupt status
1919 * @addr: address value
1920 * Description: update alarm bits in alarm register
1924 static void do_s2io_write_bits(u64 value, int flag, void __iomem *addr)
1928 temp64 = readq(addr);
1930 if(flag == ENABLE_INTRS)
1931 temp64 &= ~((u64) value);
1933 temp64 |= ((u64) value);
1934 writeq(temp64, addr);
1937 static void en_dis_err_alarms(struct s2io_nic *nic, u16 mask, int flag)
1939 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1940 register u64 gen_int_mask = 0;
1942 if (mask & TX_DMA_INTR) {
1944 gen_int_mask |= TXDMA_INT_M;
1946 do_s2io_write_bits(TXDMA_TDA_INT | TXDMA_PFC_INT |
1947 TXDMA_PCC_INT | TXDMA_TTI_INT |
1948 TXDMA_LSO_INT | TXDMA_TPA_INT |
1949 TXDMA_SM_INT, flag, &bar0->txdma_int_mask);
1951 do_s2io_write_bits(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM |
1952 PFC_MISC_0_ERR | PFC_MISC_1_ERR |
1953 PFC_PCIX_ERR | PFC_ECC_SG_ERR, flag,
1954 &bar0->pfc_err_mask);
1956 do_s2io_write_bits(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
1957 TDA_SM1_ERR_ALARM | TDA_Fn_ECC_SG_ERR |
1958 TDA_PCIX_ERR, flag, &bar0->tda_err_mask);
1960 do_s2io_write_bits(PCC_FB_ECC_DB_ERR | PCC_TXB_ECC_DB_ERR |
1961 PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM |
1962 PCC_N_SERR | PCC_6_COF_OV_ERR |
1963 PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR |
1964 PCC_7_LSO_OV_ERR | PCC_FB_ECC_SG_ERR |
1965 PCC_TXB_ECC_SG_ERR, flag, &bar0->pcc_err_mask);
1967 do_s2io_write_bits(TTI_SM_ERR_ALARM | TTI_ECC_SG_ERR |
1968 TTI_ECC_DB_ERR, flag, &bar0->tti_err_mask);
1970 do_s2io_write_bits(LSO6_ABORT | LSO7_ABORT |
1971 LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM |
1972 LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
1973 flag, &bar0->lso_err_mask);
1975 do_s2io_write_bits(TPA_SM_ERR_ALARM | TPA_TX_FRM_DROP,
1976 flag, &bar0->tpa_err_mask);
1978 do_s2io_write_bits(SM_SM_ERR_ALARM, flag, &bar0->sm_err_mask);
1982 if (mask & TX_MAC_INTR) {
1983 gen_int_mask |= TXMAC_INT_M;
1984 do_s2io_write_bits(MAC_INT_STATUS_TMAC_INT, flag,
1985 &bar0->mac_int_mask);
1986 do_s2io_write_bits(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR |
1987 TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR |
1988 TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
1989 flag, &bar0->mac_tmac_err_mask);
1992 if (mask & TX_XGXS_INTR) {
1993 gen_int_mask |= TXXGXS_INT_M;
1994 do_s2io_write_bits(XGXS_INT_STATUS_TXGXS, flag,
1995 &bar0->xgxs_int_mask);
1996 do_s2io_write_bits(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR |
1997 TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
1998 flag, &bar0->xgxs_txgxs_err_mask);
2001 if (mask & RX_DMA_INTR) {
2002 gen_int_mask |= RXDMA_INT_M;
2003 do_s2io_write_bits(RXDMA_INT_RC_INT_M | RXDMA_INT_RPA_INT_M |
2004 RXDMA_INT_RDA_INT_M | RXDMA_INT_RTI_INT_M,
2005 flag, &bar0->rxdma_int_mask);
2006 do_s2io_write_bits(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR |
2007 RC_PRCn_SM_ERR_ALARM | RC_FTC_SM_ERR_ALARM |
2008 RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR |
2009 RC_RDA_FAIL_WR_Rn, flag, &bar0->rc_err_mask);
2010 do_s2io_write_bits(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn |
2011 PRC_PCI_AB_F_WR_Rn | PRC_PCI_DP_RD_Rn |
2012 PRC_PCI_DP_WR_Rn | PRC_PCI_DP_F_WR_Rn, flag,
2013 &bar0->prc_pcix_err_mask);
2014 do_s2io_write_bits(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR |
2015 RPA_ECC_SG_ERR | RPA_ECC_DB_ERR, flag,
2016 &bar0->rpa_err_mask);
2017 do_s2io_write_bits(RDA_RXDn_ECC_DB_ERR | RDA_FRM_ECC_DB_N_AERR |
2018 RDA_SM1_ERR_ALARM | RDA_SM0_ERR_ALARM |
2019 RDA_RXD_ECC_DB_SERR | RDA_RXDn_ECC_SG_ERR |
2020 RDA_FRM_ECC_SG_ERR | RDA_MISC_ERR|RDA_PCIX_ERR,
2021 flag, &bar0->rda_err_mask);
2022 do_s2io_write_bits(RTI_SM_ERR_ALARM |
2023 RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
2024 flag, &bar0->rti_err_mask);
2027 if (mask & RX_MAC_INTR) {
2028 gen_int_mask |= RXMAC_INT_M;
2029 do_s2io_write_bits(MAC_INT_STATUS_RMAC_INT, flag,
2030 &bar0->mac_int_mask);
2031 do_s2io_write_bits(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR |
2032 RMAC_UNUSED_INT | RMAC_SINGLE_ECC_ERR |
2033 RMAC_DOUBLE_ECC_ERR |
2034 RMAC_LINK_STATE_CHANGE_INT,
2035 flag, &bar0->mac_rmac_err_mask);
2038 if (mask & RX_XGXS_INTR)
2040 gen_int_mask |= RXXGXS_INT_M;
2041 do_s2io_write_bits(XGXS_INT_STATUS_RXGXS, flag,
2042 &bar0->xgxs_int_mask);
2043 do_s2io_write_bits(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR, flag,
2044 &bar0->xgxs_rxgxs_err_mask);
2047 if (mask & MC_INTR) {
2048 gen_int_mask |= MC_INT_M;
2049 do_s2io_write_bits(MC_INT_MASK_MC_INT, flag, &bar0->mc_int_mask);
2050 do_s2io_write_bits(MC_ERR_REG_SM_ERR | MC_ERR_REG_ECC_ALL_SNG |
2051 MC_ERR_REG_ECC_ALL_DBL | PLL_LOCK_N, flag,
2052 &bar0->mc_err_mask);
2054 nic->general_int_mask = gen_int_mask;
2056 /* Remove this line when alarm interrupts are enabled */
2057 nic->general_int_mask = 0;
2060 * en_dis_able_nic_intrs - Enable or Disable the interrupts
2061 * @nic: device private variable,
2062 * @mask: A mask indicating which Intr block must be modified and,
2063 * @flag: A flag indicating whether to enable or disable the Intrs.
2064 * Description: This function will either disable or enable the interrupts
2065 * depending on the flag argument. The mask argument can be used to
2066 * enable/disable any Intr block.
2067 * Return Value: NONE.
2070 static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag)
2072 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2073 register u64 temp64 = 0, intr_mask = 0;
2075 intr_mask = nic->general_int_mask;
2077 /* Top level interrupt classification */
2078 /* PIC Interrupts */
2079 if (mask & TX_PIC_INTR) {
2080 /* Enable PIC Intrs in the general intr mask register */
2081 intr_mask |= TXPIC_INT_M;
2082 if (flag == ENABLE_INTRS) {
2084 * If Hercules adapter enable GPIO otherwise
2085 * disable all PCIX, Flash, MDIO, IIC and GPIO
2086 * interrupts for now.
2089 if (s2io_link_fault_indication(nic) ==
2090 LINK_UP_DOWN_INTERRUPT ) {
2091 do_s2io_write_bits(PIC_INT_GPIO, flag,
2092 &bar0->pic_int_mask);
2093 do_s2io_write_bits(GPIO_INT_MASK_LINK_UP, flag,
2094 &bar0->gpio_int_mask);
2096 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
2097 } else if (flag == DISABLE_INTRS) {
2099 * Disable PIC Intrs in the general
2100 * intr mask register
2102 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
2106 /* Tx traffic interrupts */
2107 if (mask & TX_TRAFFIC_INTR) {
2108 intr_mask |= TXTRAFFIC_INT_M;
2109 if (flag == ENABLE_INTRS) {
2111 * Enable all the Tx side interrupts
2112 * writing 0 Enables all 64 TX interrupt levels
2114 writeq(0x0, &bar0->tx_traffic_mask);
2115 } else if (flag == DISABLE_INTRS) {
2117 * Disable Tx Traffic Intrs in the general intr mask
2120 writeq(DISABLE_ALL_INTRS, &bar0->tx_traffic_mask);
2124 /* Rx traffic interrupts */
2125 if (mask & RX_TRAFFIC_INTR) {
2126 intr_mask |= RXTRAFFIC_INT_M;
2127 if (flag == ENABLE_INTRS) {
2128 /* writing 0 Enables all 8 RX interrupt levels */
2129 writeq(0x0, &bar0->rx_traffic_mask);
2130 } else if (flag == DISABLE_INTRS) {
2132 * Disable Rx Traffic Intrs in the general intr mask
2135 writeq(DISABLE_ALL_INTRS, &bar0->rx_traffic_mask);
2139 temp64 = readq(&bar0->general_int_mask);
2140 if (flag == ENABLE_INTRS)
2141 temp64 &= ~((u64) intr_mask);
2143 temp64 = DISABLE_ALL_INTRS;
2144 writeq(temp64, &bar0->general_int_mask);
2146 nic->general_int_mask = readq(&bar0->general_int_mask);
2150 * verify_pcc_quiescent- Checks for PCC quiescent state
2151 * Return: 1 If PCC is quiescence
2152 * 0 If PCC is not quiescence
2154 static int verify_pcc_quiescent(struct s2io_nic *sp, int flag)
2157 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2158 u64 val64 = readq(&bar0->adapter_status);
2160 herc = (sp->device_type == XFRAME_II_DEVICE);
2162 if (flag == FALSE) {
2163 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
2164 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE))
2167 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2171 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
2172 if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
2173 ADAPTER_STATUS_RMAC_PCC_IDLE))
2176 if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) ==
2177 ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2185 * verify_xena_quiescence - Checks whether the H/W is ready
2186 * Description: Returns whether the H/W is ready to go or not. Depending
2187 * on whether adapter enable bit was written or not the comparison
2188 * differs and the calling function passes the input argument flag to
2190 * Return: 1 If xena is quiescence
2191 * 0 If Xena is not quiescence
2194 static int verify_xena_quiescence(struct s2io_nic *sp)
2197 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2198 u64 val64 = readq(&bar0->adapter_status);
2199 mode = s2io_verify_pci_mode(sp);
2201 if (!(val64 & ADAPTER_STATUS_TDMA_READY)) {
2202 DBG_PRINT(ERR_DBG, "%s", "TDMA is not ready!");
2205 if (!(val64 & ADAPTER_STATUS_RDMA_READY)) {
2206 DBG_PRINT(ERR_DBG, "%s", "RDMA is not ready!");
2209 if (!(val64 & ADAPTER_STATUS_PFC_READY)) {
2210 DBG_PRINT(ERR_DBG, "%s", "PFC is not ready!");
2213 if (!(val64 & ADAPTER_STATUS_TMAC_BUF_EMPTY)) {
2214 DBG_PRINT(ERR_DBG, "%s", "TMAC BUF is not empty!");
2217 if (!(val64 & ADAPTER_STATUS_PIC_QUIESCENT)) {
2218 DBG_PRINT(ERR_DBG, "%s", "PIC is not QUIESCENT!");
2221 if (!(val64 & ADAPTER_STATUS_MC_DRAM_READY)) {
2222 DBG_PRINT(ERR_DBG, "%s", "MC_DRAM is not ready!");
2225 if (!(val64 & ADAPTER_STATUS_MC_QUEUES_READY)) {
2226 DBG_PRINT(ERR_DBG, "%s", "MC_QUEUES is not ready!");
2229 if (!(val64 & ADAPTER_STATUS_M_PLL_LOCK)) {
2230 DBG_PRINT(ERR_DBG, "%s", "M_PLL is not locked!");
2235 * In PCI 33 mode, the P_PLL is not used, and therefore,
2236 * the the P_PLL_LOCK bit in the adapter_status register will
2239 if (!(val64 & ADAPTER_STATUS_P_PLL_LOCK) &&
2240 sp->device_type == XFRAME_II_DEVICE && mode !=
2242 DBG_PRINT(ERR_DBG, "%s", "P_PLL is not locked!");
2245 if (!((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
2246 ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
2247 DBG_PRINT(ERR_DBG, "%s", "RC_PRC is not QUIESCENT!");
2254 * fix_mac_address - Fix for Mac addr problem on Alpha platforms
2255 * @sp: Pointer to device specifc structure
2257 * New procedure to clear mac address reading problems on Alpha platforms
2261 static void fix_mac_address(struct s2io_nic * sp)
2263 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2267 while (fix_mac[i] != END_SIGN) {
2268 writeq(fix_mac[i++], &bar0->gpio_control);
2270 val64 = readq(&bar0->gpio_control);
2275 * start_nic - Turns the device on
2276 * @nic : device private variable.
2278 * This function actually turns the device on. Before this function is
2279 * called,all Registers are configured from their reset states
2280 * and shared memory is allocated but the NIC is still quiescent. On
2281 * calling this function, the device interrupts are cleared and the NIC is
2282 * literally switched on by writing into the adapter control register.
2284 * SUCCESS on success and -1 on failure.
2287 static int start_nic(struct s2io_nic *nic)
2289 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2290 struct net_device *dev = nic->dev;
2291 register u64 val64 = 0;
2293 struct mac_info *mac_control;
2294 struct config_param *config;
2296 mac_control = &nic->mac_control;
2297 config = &nic->config;
2299 /* PRC Initialization and configuration */
2300 for (i = 0; i < config->rx_ring_num; i++) {
2301 writeq((u64) mac_control->rings[i].rx_blocks[0].block_dma_addr,
2302 &bar0->prc_rxd0_n[i]);
2304 val64 = readq(&bar0->prc_ctrl_n[i]);
2305 if (nic->rxd_mode == RXD_MODE_1)
2306 val64 |= PRC_CTRL_RC_ENABLED;
2308 val64 |= PRC_CTRL_RC_ENABLED | PRC_CTRL_RING_MODE_3;
2309 if (nic->device_type == XFRAME_II_DEVICE)
2310 val64 |= PRC_CTRL_GROUP_READS;
2311 val64 &= ~PRC_CTRL_RXD_BACKOFF_INTERVAL(0xFFFFFF);
2312 val64 |= PRC_CTRL_RXD_BACKOFF_INTERVAL(0x1000);
2313 writeq(val64, &bar0->prc_ctrl_n[i]);
2316 if (nic->rxd_mode == RXD_MODE_3B) {
2317 /* Enabling 2 buffer mode by writing into Rx_pa_cfg reg. */
2318 val64 = readq(&bar0->rx_pa_cfg);
2319 val64 |= RX_PA_CFG_IGNORE_L2_ERR;
2320 writeq(val64, &bar0->rx_pa_cfg);
2323 if (vlan_tag_strip == 0) {
2324 val64 = readq(&bar0->rx_pa_cfg);
2325 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
2326 writeq(val64, &bar0->rx_pa_cfg);
2327 vlan_strip_flag = 0;
2331 * Enabling MC-RLDRAM. After enabling the device, we timeout
2332 * for around 100ms, which is approximately the time required
2333 * for the device to be ready for operation.
2335 val64 = readq(&bar0->mc_rldram_mrs);
2336 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE | MC_RLDRAM_MRS_ENABLE;
2337 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
2338 val64 = readq(&bar0->mc_rldram_mrs);
2340 msleep(100); /* Delay by around 100 ms. */
2342 /* Enabling ECC Protection. */
2343 val64 = readq(&bar0->adapter_control);
2344 val64 &= ~ADAPTER_ECC_EN;
2345 writeq(val64, &bar0->adapter_control);
2348 * Verify if the device is ready to be enabled, if so enable
2351 val64 = readq(&bar0->adapter_status);
2352 if (!verify_xena_quiescence(nic)) {
2353 DBG_PRINT(ERR_DBG, "%s: device is not ready, ", dev->name);
2354 DBG_PRINT(ERR_DBG, "Adapter status reads: 0x%llx\n",
2355 (unsigned long long) val64);
2360 * With some switches, link might be already up at this point.
2361 * Because of this weird behavior, when we enable laser,
2362 * we may not get link. We need to handle this. We cannot
2363 * figure out which switch is misbehaving. So we are forced to
2364 * make a global change.
2367 /* Enabling Laser. */
2368 val64 = readq(&bar0->adapter_control);
2369 val64 |= ADAPTER_EOI_TX_ON;
2370 writeq(val64, &bar0->adapter_control);
2372 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
2374 * Dont see link state interrupts initally on some switches,
2375 * so directly scheduling the link state task here.
2377 schedule_work(&nic->set_link_task);
2379 /* SXE-002: Initialize link and activity LED */
2380 subid = nic->pdev->subsystem_device;
2381 if (((subid & 0xFF) >= 0x07) &&
2382 (nic->device_type == XFRAME_I_DEVICE)) {
2383 val64 = readq(&bar0->gpio_control);
2384 val64 |= 0x0000800000000000ULL;
2385 writeq(val64, &bar0->gpio_control);
2386 val64 = 0x0411040400000000ULL;
2387 writeq(val64, (void __iomem *)bar0 + 0x2700);
2393 * s2io_txdl_getskb - Get the skb from txdl, unmap and return skb
2395 static struct sk_buff *s2io_txdl_getskb(struct fifo_info *fifo_data, struct \
2396 TxD *txdlp, int get_off)
2398 struct s2io_nic *nic = fifo_data->nic;
2399 struct sk_buff *skb;
2404 if (txds->Host_Control == (u64)(long)fifo_data->ufo_in_band_v) {
2405 pci_unmap_single(nic->pdev, (dma_addr_t)
2406 txds->Buffer_Pointer, sizeof(u64),
2411 skb = (struct sk_buff *) ((unsigned long)
2412 txds->Host_Control);
2414 memset(txdlp, 0, (sizeof(struct TxD) * fifo_data->max_txds));
2417 pci_unmap_single(nic->pdev, (dma_addr_t)
2418 txds->Buffer_Pointer,
2419 skb->len - skb->data_len,
2421 frg_cnt = skb_shinfo(skb)->nr_frags;
2424 for (j = 0; j < frg_cnt; j++, txds++) {
2425 skb_frag_t *frag = &skb_shinfo(skb)->frags[j];
2426 if (!txds->Buffer_Pointer)
2428 pci_unmap_page(nic->pdev, (dma_addr_t)
2429 txds->Buffer_Pointer,
2430 frag->size, PCI_DMA_TODEVICE);
2433 memset(txdlp,0, (sizeof(struct TxD) * fifo_data->max_txds));
2438 * free_tx_buffers - Free all queued Tx buffers
2439 * @nic : device private variable.
2441 * Free all queued Tx buffers.
2442 * Return Value: void
2445 static void free_tx_buffers(struct s2io_nic *nic)
2447 struct net_device *dev = nic->dev;
2448 struct sk_buff *skb;
2451 struct mac_info *mac_control;
2452 struct config_param *config;
2455 mac_control = &nic->mac_control;
2456 config = &nic->config;
2458 for (i = 0; i < config->tx_fifo_num; i++) {
2459 unsigned long flags;
2460 spin_lock_irqsave(&mac_control->fifos[i].tx_lock, flags);
2461 for (j = 0; j < config->tx_cfg[i].fifo_len - 1; j++) {
2462 txdp = (struct TxD *) \
2463 mac_control->fifos[i].list_info[j].list_virt_addr;
2464 skb = s2io_txdl_getskb(&mac_control->fifos[i], txdp, j);
2466 nic->mac_control.stats_info->sw_stat.mem_freed
2473 "%s:forcibly freeing %d skbs on FIFO%d\n",
2475 mac_control->fifos[i].tx_curr_get_info.offset = 0;
2476 mac_control->fifos[i].tx_curr_put_info.offset = 0;
2477 spin_unlock_irqrestore(&mac_control->fifos[i].tx_lock, flags);
2482 * stop_nic - To stop the nic
2483 * @nic ; device private variable.
2485 * This function does exactly the opposite of what the start_nic()
2486 * function does. This function is called to stop the device.
2491 static void stop_nic(struct s2io_nic *nic)
2493 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2494 register u64 val64 = 0;
2496 struct mac_info *mac_control;
2497 struct config_param *config;
2499 mac_control = &nic->mac_control;
2500 config = &nic->config;
2502 /* Disable all interrupts */
2503 en_dis_err_alarms(nic, ENA_ALL_INTRS, DISABLE_INTRS);
2504 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
2505 interruptible |= TX_PIC_INTR;
2506 en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS);
2508 /* Clearing Adapter_En bit of ADAPTER_CONTROL Register */
2509 val64 = readq(&bar0->adapter_control);
2510 val64 &= ~(ADAPTER_CNTL_EN);
2511 writeq(val64, &bar0->adapter_control);
2515 * fill_rx_buffers - Allocates the Rx side skbs
2516 * @nic: device private variable
2517 * @ring_no: ring number
2519 * The function allocates Rx side skbs and puts the physical
2520 * address of these buffers into the RxD buffer pointers, so that the NIC
2521 * can DMA the received frame into these locations.
2522 * The NIC supports 3 receive modes, viz
2524 * 2. three buffer and
2525 * 3. Five buffer modes.
2526 * Each mode defines how many fragments the received frame will be split
2527 * up into by the NIC. The frame is split into L3 header, L4 Header,
2528 * L4 payload in three buffer mode and in 5 buffer mode, L4 payload itself
2529 * is split into 3 fragments. As of now only single buffer mode is
2532 * SUCCESS on success or an appropriate -ve value on failure.
2535 static int fill_rx_buffers(struct s2io_nic *nic, int ring_no)
2537 struct net_device *dev = nic->dev;
2538 struct sk_buff *skb;
2540 int off, off1, size, block_no, block_no1;
2543 struct mac_info *mac_control;
2544 struct config_param *config;
2547 unsigned long flags;
2548 struct RxD_t *first_rxdp = NULL;
2549 u64 Buffer0_ptr = 0, Buffer1_ptr = 0;
2552 struct swStat *stats = &nic->mac_control.stats_info->sw_stat;
2554 mac_control = &nic->mac_control;
2555 config = &nic->config;
2556 alloc_cnt = mac_control->rings[ring_no].pkt_cnt -
2557 atomic_read(&nic->rx_bufs_left[ring_no]);
2559 block_no1 = mac_control->rings[ring_no].rx_curr_get_info.block_index;
2560 off1 = mac_control->rings[ring_no].rx_curr_get_info.offset;
2561 while (alloc_tab < alloc_cnt) {
2562 block_no = mac_control->rings[ring_no].rx_curr_put_info.
2564 off = mac_control->rings[ring_no].rx_curr_put_info.offset;
2566 rxdp = mac_control->rings[ring_no].
2567 rx_blocks[block_no].rxds[off].virt_addr;
2569 if ((block_no == block_no1) && (off == off1) &&
2570 (rxdp->Host_Control)) {
2571 DBG_PRINT(INTR_DBG, "%s: Get and Put",
2573 DBG_PRINT(INTR_DBG, " info equated\n");
2576 if (off && (off == rxd_count[nic->rxd_mode])) {
2577 mac_control->rings[ring_no].rx_curr_put_info.
2579 if (mac_control->rings[ring_no].rx_curr_put_info.
2580 block_index == mac_control->rings[ring_no].
2582 mac_control->rings[ring_no].rx_curr_put_info.
2584 block_no = mac_control->rings[ring_no].
2585 rx_curr_put_info.block_index;
2586 if (off == rxd_count[nic->rxd_mode])
2588 mac_control->rings[ring_no].rx_curr_put_info.
2590 rxdp = mac_control->rings[ring_no].
2591 rx_blocks[block_no].block_virt_addr;
2592 DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n",
2596 spin_lock_irqsave(&nic->put_lock, flags);
2597 mac_control->rings[ring_no].put_pos =
2598 (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
2599 spin_unlock_irqrestore(&nic->put_lock, flags);
2601 mac_control->rings[ring_no].put_pos =
2602 (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
2604 if ((rxdp->Control_1 & RXD_OWN_XENA) &&
2605 ((nic->rxd_mode == RXD_MODE_3B) &&
2606 (rxdp->Control_2 & s2BIT(0)))) {
2607 mac_control->rings[ring_no].rx_curr_put_info.
2611 /* calculate size of skb based on ring mode */
2612 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
2613 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
2614 if (nic->rxd_mode == RXD_MODE_1)
2615 size += NET_IP_ALIGN;
2617 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
2620 skb = dev_alloc_skb(size);
2622 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
2623 DBG_PRINT(INFO_DBG, "memory to allocate SKBs\n");
2626 first_rxdp->Control_1 |= RXD_OWN_XENA;
2628 nic->mac_control.stats_info->sw_stat. \
2629 mem_alloc_fail_cnt++;
2632 nic->mac_control.stats_info->sw_stat.mem_allocated
2634 if (nic->rxd_mode == RXD_MODE_1) {
2635 /* 1 buffer mode - normal operation mode */
2636 rxdp1 = (struct RxD1*)rxdp;
2637 memset(rxdp, 0, sizeof(struct RxD1));
2638 skb_reserve(skb, NET_IP_ALIGN);
2639 rxdp1->Buffer0_ptr = pci_map_single
2640 (nic->pdev, skb->data, size - NET_IP_ALIGN,
2641 PCI_DMA_FROMDEVICE);
2642 if( (rxdp1->Buffer0_ptr == 0) ||
2643 (rxdp1->Buffer0_ptr ==
2645 goto pci_map_failed;
2648 SET_BUFFER0_SIZE_1(size - NET_IP_ALIGN);
2650 } else if (nic->rxd_mode == RXD_MODE_3B) {
2653 * 2 buffer mode provides 128
2654 * byte aligned receive buffers.
2657 rxdp3 = (struct RxD3*)rxdp;
2658 /* save buffer pointers to avoid frequent dma mapping */
2659 Buffer0_ptr = rxdp3->Buffer0_ptr;
2660 Buffer1_ptr = rxdp3->Buffer1_ptr;
2661 memset(rxdp, 0, sizeof(struct RxD3));
2662 /* restore the buffer pointers for dma sync*/
2663 rxdp3->Buffer0_ptr = Buffer0_ptr;
2664 rxdp3->Buffer1_ptr = Buffer1_ptr;
2666 ba = &mac_control->rings[ring_no].ba[block_no][off];
2667 skb_reserve(skb, BUF0_LEN);
2668 tmp = (u64)(unsigned long) skb->data;
2671 skb->data = (void *) (unsigned long)tmp;
2672 skb_reset_tail_pointer(skb);
2674 if (!(rxdp3->Buffer0_ptr))
2675 rxdp3->Buffer0_ptr =
2676 pci_map_single(nic->pdev, ba->ba_0, BUF0_LEN,
2677 PCI_DMA_FROMDEVICE);
2679 pci_dma_sync_single_for_device(nic->pdev,
2680 (dma_addr_t) rxdp3->Buffer0_ptr,
2681 BUF0_LEN, PCI_DMA_FROMDEVICE);
2682 if( (rxdp3->Buffer0_ptr == 0) ||
2683 (rxdp3->Buffer0_ptr == DMA_ERROR_CODE))
2684 goto pci_map_failed;
2686 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
2687 if (nic->rxd_mode == RXD_MODE_3B) {
2688 /* Two buffer mode */
2691 * Buffer2 will have L3/L4 header plus
2694 rxdp3->Buffer2_ptr = pci_map_single
2695 (nic->pdev, skb->data, dev->mtu + 4,
2696 PCI_DMA_FROMDEVICE);
2698 if( (rxdp3->Buffer2_ptr == 0) ||
2699 (rxdp3->Buffer2_ptr == DMA_ERROR_CODE))
2700 goto pci_map_failed;
2702 rxdp3->Buffer1_ptr =
2703 pci_map_single(nic->pdev,
2705 PCI_DMA_FROMDEVICE);
2706 if( (rxdp3->Buffer1_ptr == 0) ||
2707 (rxdp3->Buffer1_ptr == DMA_ERROR_CODE)) {
2710 (dma_addr_t)rxdp3->Buffer2_ptr,
2712 PCI_DMA_FROMDEVICE);
2713 goto pci_map_failed;
2715 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
2716 rxdp->Control_2 |= SET_BUFFER2_SIZE_3
2719 rxdp->Control_2 |= s2BIT(0);
2721 rxdp->Host_Control = (unsigned long) (skb);
2722 if (alloc_tab & ((1 << rxsync_frequency) - 1))
2723 rxdp->Control_1 |= RXD_OWN_XENA;
2725 if (off == (rxd_count[nic->rxd_mode] + 1))
2727 mac_control->rings[ring_no].rx_curr_put_info.offset = off;
2729 rxdp->Control_2 |= SET_RXD_MARKER;
2730 if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) {
2733 first_rxdp->Control_1 |= RXD_OWN_XENA;
2737 atomic_inc(&nic->rx_bufs_left[ring_no]);
2742 /* Transfer ownership of first descriptor to adapter just before
2743 * exiting. Before that, use memory barrier so that ownership
2744 * and other fields are seen by adapter correctly.
2748 first_rxdp->Control_1 |= RXD_OWN_XENA;
2753 stats->pci_map_fail_cnt++;
2754 stats->mem_freed += skb->truesize;
2755 dev_kfree_skb_irq(skb);
2759 static void free_rxd_blk(struct s2io_nic *sp, int ring_no, int blk)
2761 struct net_device *dev = sp->dev;
2763 struct sk_buff *skb;
2765 struct mac_info *mac_control;
2770 mac_control = &sp->mac_control;
2771 for (j = 0 ; j < rxd_count[sp->rxd_mode]; j++) {
2772 rxdp = mac_control->rings[ring_no].
2773 rx_blocks[blk].rxds[j].virt_addr;
2774 skb = (struct sk_buff *)
2775 ((unsigned long) rxdp->Host_Control);
2779 if (sp->rxd_mode == RXD_MODE_1) {
2780 rxdp1 = (struct RxD1*)rxdp;
2781 pci_unmap_single(sp->pdev, (dma_addr_t)
2784 HEADER_ETHERNET_II_802_3_SIZE
2785 + HEADER_802_2_SIZE +
2787 PCI_DMA_FROMDEVICE);
2788 memset(rxdp, 0, sizeof(struct RxD1));
2789 } else if(sp->rxd_mode == RXD_MODE_3B) {
2790 rxdp3 = (struct RxD3*)rxdp;
2791 ba = &mac_control->rings[ring_no].
2793 pci_unmap_single(sp->pdev, (dma_addr_t)
2796 PCI_DMA_FROMDEVICE);
2797 pci_unmap_single(sp->pdev, (dma_addr_t)
2800 PCI_DMA_FROMDEVICE);
2801 pci_unmap_single(sp->pdev, (dma_addr_t)
2804 PCI_DMA_FROMDEVICE);
2805 memset(rxdp, 0, sizeof(struct RxD3));
2807 sp->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
2809 atomic_dec(&sp->rx_bufs_left[ring_no]);
2814 * free_rx_buffers - Frees all Rx buffers
2815 * @sp: device private variable.
2817 * This function will free all Rx buffers allocated by host.
2822 static void free_rx_buffers(struct s2io_nic *sp)
2824 struct net_device *dev = sp->dev;
2825 int i, blk = 0, buf_cnt = 0;
2826 struct mac_info *mac_control;
2827 struct config_param *config;
2829 mac_control = &sp->mac_control;
2830 config = &sp->config;
2832 for (i = 0; i < config->rx_ring_num; i++) {
2833 for (blk = 0; blk < rx_ring_sz[i]; blk++)
2834 free_rxd_blk(sp,i,blk);
2836 mac_control->rings[i].rx_curr_put_info.block_index = 0;
2837 mac_control->rings[i].rx_curr_get_info.block_index = 0;
2838 mac_control->rings[i].rx_curr_put_info.offset = 0;
2839 mac_control->rings[i].rx_curr_get_info.offset = 0;
2840 atomic_set(&sp->rx_bufs_left[i], 0);
2841 DBG_PRINT(INIT_DBG, "%s:Freed 0x%x Rx Buffers on ring%d\n",
2842 dev->name, buf_cnt, i);
2847 * s2io_poll - Rx interrupt handler for NAPI support
2848 * @napi : pointer to the napi structure.
2849 * @budget : The number of packets that were budgeted to be processed
2850 * during one pass through the 'Poll" function.
2852 * Comes into picture only if NAPI support has been incorporated. It does
2853 * the same thing that rx_intr_handler does, but not in a interrupt context
2854 * also It will process only a given number of packets.
2856 * 0 on success and 1 if there are No Rx packets to be processed.
2859 static int s2io_poll(struct napi_struct *napi, int budget)
2861 struct s2io_nic *nic = container_of(napi, struct s2io_nic, napi);
2862 struct net_device *dev = nic->dev;
2863 int pkt_cnt = 0, org_pkts_to_process;
2864 struct mac_info *mac_control;
2865 struct config_param *config;
2866 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2869 mac_control = &nic->mac_control;
2870 config = &nic->config;
2872 nic->pkts_to_process = budget;
2873 org_pkts_to_process = nic->pkts_to_process;
2875 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
2876 readl(&bar0->rx_traffic_int);
2878 for (i = 0; i < config->rx_ring_num; i++) {
2879 rx_intr_handler(&mac_control->rings[i]);
2880 pkt_cnt = org_pkts_to_process - nic->pkts_to_process;
2881 if (!nic->pkts_to_process) {
2882 /* Quota for the current iteration has been met */
2887 netif_rx_complete(dev, napi);
2889 for (i = 0; i < config->rx_ring_num; i++) {
2890 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2891 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2892 DBG_PRINT(INFO_DBG, " in Rx Poll!!\n");
2896 /* Re enable the Rx interrupts. */
2897 writeq(0x0, &bar0->rx_traffic_mask);
2898 readl(&bar0->rx_traffic_mask);
2902 for (i = 0; i < config->rx_ring_num; i++) {
2903 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2904 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2905 DBG_PRINT(INFO_DBG, " in Rx Poll!!\n");
2912 #ifdef CONFIG_NET_POLL_CONTROLLER
2914 * s2io_netpoll - netpoll event handler entry point
2915 * @dev : pointer to the device structure.
2917 * This function will be called by upper layer to check for events on the
2918 * interface in situations where interrupts are disabled. It is used for
2919 * specific in-kernel networking tasks, such as remote consoles and kernel
2920 * debugging over the network (example netdump in RedHat).
2922 static void s2io_netpoll(struct net_device *dev)
2924 struct s2io_nic *nic = dev->priv;
2925 struct mac_info *mac_control;
2926 struct config_param *config;
2927 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2928 u64 val64 = 0xFFFFFFFFFFFFFFFFULL;
2931 if (pci_channel_offline(nic->pdev))
2934 disable_irq(dev->irq);
2936 mac_control = &nic->mac_control;
2937 config = &nic->config;
2939 writeq(val64, &bar0->rx_traffic_int);
2940 writeq(val64, &bar0->tx_traffic_int);
2942 /* we need to free up the transmitted skbufs or else netpoll will
2943 * run out of skbs and will fail and eventually netpoll application such
2944 * as netdump will fail.
2946 for (i = 0; i < config->tx_fifo_num; i++)
2947 tx_intr_handler(&mac_control->fifos[i]);
2949 /* check for received packet and indicate up to network */
2950 for (i = 0; i < config->rx_ring_num; i++)
2951 rx_intr_handler(&mac_control->rings[i]);
2953 for (i = 0; i < config->rx_ring_num; i++) {
2954 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2955 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2956 DBG_PRINT(INFO_DBG, " in Rx Netpoll!!\n");
2960 enable_irq(dev->irq);
2966 * rx_intr_handler - Rx interrupt handler
2967 * @nic: device private variable.
2969 * If the interrupt is because of a received frame or if the
2970 * receive ring contains fresh as yet un-processed frames,this function is
2971 * called. It picks out the RxD at which place the last Rx processing had
2972 * stopped and sends the skb to the OSM's Rx handler and then increments
2977 static void rx_intr_handler(struct ring_info *ring_data)
2979 struct s2io_nic *nic = ring_data->nic;
2980 struct net_device *dev = (struct net_device *) nic->dev;
2981 int get_block, put_block, put_offset;
2982 struct rx_curr_get_info get_info, put_info;
2984 struct sk_buff *skb;
2990 spin_lock(&nic->rx_lock);
2992 get_info = ring_data->rx_curr_get_info;
2993 get_block = get_info.block_index;
2994 memcpy(&put_info, &ring_data->rx_curr_put_info, sizeof(put_info));
2995 put_block = put_info.block_index;
2996 rxdp = ring_data->rx_blocks[get_block].rxds[get_info.offset].virt_addr;
2998 spin_lock(&nic->put_lock);
2999 put_offset = ring_data->put_pos;
3000 spin_unlock(&nic->put_lock);
3002 put_offset = ring_data->put_pos;
3004 while (RXD_IS_UP2DT(rxdp)) {
3006 * If your are next to put index then it's
3007 * FIFO full condition
3009 if ((get_block == put_block) &&
3010 (get_info.offset + 1) == put_info.offset) {
3011 DBG_PRINT(INTR_DBG, "%s: Ring Full\n",dev->name);
3014 skb = (struct sk_buff *) ((unsigned long)rxdp->Host_Control);
3016 DBG_PRINT(ERR_DBG, "%s: The skb is ",
3018 DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
3019 spin_unlock(&nic->rx_lock);
3022 if (nic->rxd_mode == RXD_MODE_1) {
3023 rxdp1 = (struct RxD1*)rxdp;
3024 pci_unmap_single(nic->pdev, (dma_addr_t)
3027 HEADER_ETHERNET_II_802_3_SIZE +
3030 PCI_DMA_FROMDEVICE);
3031 } else if (nic->rxd_mode == RXD_MODE_3B) {
3032 rxdp3 = (struct RxD3*)rxdp;
3033 pci_dma_sync_single_for_cpu(nic->pdev, (dma_addr_t)
3035 BUF0_LEN, PCI_DMA_FROMDEVICE);
3036 pci_unmap_single(nic->pdev, (dma_addr_t)
3039 PCI_DMA_FROMDEVICE);
3041 prefetch(skb->data);
3042 rx_osm_handler(ring_data, rxdp);
3044 ring_data->rx_curr_get_info.offset = get_info.offset;
3045 rxdp = ring_data->rx_blocks[get_block].
3046 rxds[get_info.offset].virt_addr;
3047 if (get_info.offset == rxd_count[nic->rxd_mode]) {
3048 get_info.offset = 0;
3049 ring_data->rx_curr_get_info.offset = get_info.offset;
3051 if (get_block == ring_data->block_count)
3053 ring_data->rx_curr_get_info.block_index = get_block;
3054 rxdp = ring_data->rx_blocks[get_block].block_virt_addr;
3057 nic->pkts_to_process -= 1;
3058 if ((napi) && (!nic->pkts_to_process))
3061 if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts))
3065 /* Clear all LRO sessions before exiting */
3066 for (i=0; i<MAX_LRO_SESSIONS; i++) {
3067 struct lro *lro = &nic->lro0_n[i];
3069 update_L3L4_header(nic, lro);
3070 queue_rx_frame(lro->parent, lro->vlan_tag);
3071 clear_lro_session(lro);
3076 spin_unlock(&nic->rx_lock);
3080 * tx_intr_handler - Transmit interrupt handler
3081 * @nic : device private variable
3083 * If an interrupt was raised to indicate DMA complete of the
3084 * Tx packet, this function is called. It identifies the last TxD
3085 * whose buffer was freed and frees all skbs whose data have already
3086 * DMA'ed into the NICs internal memory.
3091 static void tx_intr_handler(struct fifo_info *fifo_data)
3093 struct s2io_nic *nic = fifo_data->nic;
3094 struct tx_curr_get_info get_info, put_info;
3095 struct sk_buff *skb = NULL;
3098 unsigned long flags = 0;
3101 if (!spin_trylock_irqsave(&fifo_data->tx_lock, flags))
3104 get_info = fifo_data->tx_curr_get_info;
3105 memcpy(&put_info, &fifo_data->tx_curr_put_info, sizeof(put_info));
3106 txdlp = (struct TxD *) fifo_data->list_info[get_info.offset].
3108 while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) &&
3109 (get_info.offset != put_info.offset) &&
3110 (txdlp->Host_Control)) {
3111 /* Check for TxD errors */
3112 if (txdlp->Control_1 & TXD_T_CODE) {
3113 unsigned long long err;
3114 err = txdlp->Control_1 & TXD_T_CODE;
3116 nic->mac_control.stats_info->sw_stat.
3120 /* update t_code statistics */
3121 err_mask = err >> 48;
3124 nic->mac_control.stats_info->sw_stat.
3129 nic->mac_control.stats_info->sw_stat.
3130 tx_desc_abort_cnt++;
3134 nic->mac_control.stats_info->sw_stat.
3135 tx_parity_err_cnt++;
3139 nic->mac_control.stats_info->sw_stat.
3144 nic->mac_control.stats_info->sw_stat.
3145 tx_list_proc_err_cnt++;
3150 skb = s2io_txdl_getskb(fifo_data, txdlp, get_info.offset);
3152 spin_unlock_irqrestore(&fifo_data->tx_lock, flags);
3153 DBG_PRINT(ERR_DBG, "%s: Null skb ",
3155 DBG_PRINT(ERR_DBG, "in Tx Free Intr\n");
3160 /* Updating the statistics block */
3161 nic->stats.tx_bytes += skb->len;
3162 nic->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
3163 dev_kfree_skb_irq(skb);
3166 if (get_info.offset == get_info.fifo_len + 1)
3167 get_info.offset = 0;
3168 txdlp = (struct TxD *) fifo_data->list_info
3169 [get_info.offset].list_virt_addr;
3170 fifo_data->tx_curr_get_info.offset =
3174 s2io_wake_tx_queue(fifo_data, pkt_cnt, nic->config.multiq);
3176 spin_unlock_irqrestore(&fifo_data->tx_lock, flags);
3180 * s2io_mdio_write - Function to write in to MDIO registers
3181 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3182 * @addr : address value
3183 * @value : data value
3184 * @dev : pointer to net_device structure
3186 * This function is used to write values to the MDIO registers
3189 static void s2io_mdio_write(u32 mmd_type, u64 addr, u16 value, struct net_device *dev)
3192 struct s2io_nic *sp = dev->priv;
3193 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3195 //address transaction
3196 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3197 | MDIO_MMD_DEV_ADDR(mmd_type)
3198 | MDIO_MMS_PRT_ADDR(0x0);
3199 writeq(val64, &bar0->mdio_control);
3200 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3201 writeq(val64, &bar0->mdio_control);
3206 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3207 | MDIO_MMD_DEV_ADDR(mmd_type)
3208 | MDIO_MMS_PRT_ADDR(0x0)
3209 | MDIO_MDIO_DATA(value)
3210 | MDIO_OP(MDIO_OP_WRITE_TRANS);
3211 writeq(val64, &bar0->mdio_control);
3212 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3213 writeq(val64, &bar0->mdio_control);
3217 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3218 | MDIO_MMD_DEV_ADDR(mmd_type)
3219 | MDIO_MMS_PRT_ADDR(0x0)
3220 | MDIO_OP(MDIO_OP_READ_TRANS);
3221 writeq(val64, &bar0->mdio_control);
3222 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3223 writeq(val64, &bar0->mdio_control);
3229 * s2io_mdio_read - Function to write in to MDIO registers
3230 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3231 * @addr : address value
3232 * @dev : pointer to net_device structure
3234 * This function is used to read values to the MDIO registers
3237 static u64 s2io_mdio_read(u32 mmd_type, u64 addr, struct net_device *dev)
3241 struct s2io_nic *sp = dev->priv;
3242 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3244 /* address transaction */
3245 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3246 | MDIO_MMD_DEV_ADDR(mmd_type)
3247 | MDIO_MMS_PRT_ADDR(0x0);
3248 writeq(val64, &bar0->mdio_control);
3249 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3250 writeq(val64, &bar0->mdio_control);
3253 /* Data transaction */
3255 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3256 | MDIO_MMD_DEV_ADDR(mmd_type)
3257 | MDIO_MMS_PRT_ADDR(0x0)
3258 | MDIO_OP(MDIO_OP_READ_TRANS);
3259 writeq(val64, &bar0->mdio_control);
3260 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3261 writeq(val64, &bar0->mdio_control);
3264 /* Read the value from regs */
3265 rval64 = readq(&bar0->mdio_control);
3266 rval64 = rval64 & 0xFFFF0000;
3267 rval64 = rval64 >> 16;
3271 * s2io_chk_xpak_counter - Function to check the status of the xpak counters
3272 * @counter : couter value to be updated
3273 * @flag : flag to indicate the status
3274 * @type : counter type
3276 * This function is to check the status of the xpak counters value
3280 static void s2io_chk_xpak_counter(u64 *counter, u64 * regs_stat, u32 index, u16 flag, u16 type)
3285 for(i = 0; i <index; i++)
3290 *counter = *counter + 1;
3291 val64 = *regs_stat & mask;
3292 val64 = val64 >> (index * 0x2);
3299 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3300 "service. Excessive temperatures may "
3301 "result in premature transceiver "
3305 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3306 "service Excessive bias currents may "
3307 "indicate imminent laser diode "
3311 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3312 "service Excessive laser output "
3313 "power may saturate far-end "
3317 DBG_PRINT(ERR_DBG, "Incorrect XPAK Alarm "
3322 val64 = val64 << (index * 0x2);
3323 *regs_stat = (*regs_stat & (~mask)) | (val64);
3326 *regs_stat = *regs_stat & (~mask);
3331 * s2io_updt_xpak_counter - Function to update the xpak counters
3332 * @dev : pointer to net_device struct
3334 * This function is to upate the status of the xpak counters value
3337 static void s2io_updt_xpak_counter(struct net_device *dev)
3345 struct s2io_nic *sp = dev->priv;
3346 struct stat_block *stat_info = sp->mac_control.stats_info;
3348 /* Check the communication with the MDIO slave */
3351 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3352 if((val64 == 0xFFFF) || (val64 == 0x0000))
3354 DBG_PRINT(ERR_DBG, "ERR: MDIO slave access failed - "
3355 "Returned %llx\n", (unsigned long long)val64);
3359 /* Check for the expecte value of 2040 at PMA address 0x0000 */
3362 DBG_PRINT(ERR_DBG, "Incorrect value at PMA address 0x0000 - ");
3363 DBG_PRINT(ERR_DBG, "Returned: %llx- Expected: 0x2040\n",
3364 (unsigned long long)val64);
3368 /* Loading the DOM register to MDIO register */
3370 s2io_mdio_write(MDIO_MMD_PMA_DEV_ADDR, addr, val16, dev);
3371 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3373 /* Reading the Alarm flags */
3376 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3378 flag = CHECKBIT(val64, 0x7);
3380 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_transceiver_temp_high,
3381 &stat_info->xpak_stat.xpak_regs_stat,
3384 if(CHECKBIT(val64, 0x6))
3385 stat_info->xpak_stat.alarm_transceiver_temp_low++;
3387 flag = CHECKBIT(val64, 0x3);
3389 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_laser_bias_current_high,
3390 &stat_info->xpak_stat.xpak_regs_stat,
3393 if(CHECKBIT(val64, 0x2))
3394 stat_info->xpak_stat.alarm_laser_bias_current_low++;
3396 flag = CHECKBIT(val64, 0x1);
3398 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_laser_output_power_high,
3399 &stat_info->xpak_stat.xpak_regs_stat,
3402 if(CHECKBIT(val64, 0x0))
3403 stat_info->xpak_stat.alarm_laser_output_power_low++;
3405 /* Reading the Warning flags */
3408 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3410 if(CHECKBIT(val64, 0x7))
3411 stat_info->xpak_stat.warn_transceiver_temp_high++;
3413 if(CHECKBIT(val64, 0x6))
3414 stat_info->xpak_stat.warn_transceiver_temp_low++;
3416 if(CHECKBIT(val64, 0x3))
3417 stat_info->xpak_stat.warn_laser_bias_current_high++;
3419 if(CHECKBIT(val64, 0x2))
3420 stat_info->xpak_stat.warn_laser_bias_current_low++;
3422 if(CHECKBIT(val64, 0x1))
3423 stat_info->xpak_stat.warn_laser_output_power_high++;
3425 if(CHECKBIT(val64, 0x0))
3426 stat_info->xpak_stat.warn_laser_output_power_low++;
3430 * wait_for_cmd_complete - waits for a command to complete.
3431 * @sp : private member of the device structure, which is a pointer to the
3432 * s2io_nic structure.
3433 * Description: Function that waits for a command to Write into RMAC
3434 * ADDR DATA registers to be completed and returns either success or
3435 * error depending on whether the command was complete or not.
3437 * SUCCESS on success and FAILURE on failure.
3440 static int wait_for_cmd_complete(void __iomem *addr, u64 busy_bit,
3443 int ret = FAILURE, cnt = 0, delay = 1;
3446 if ((bit_state != S2IO_BIT_RESET) && (bit_state != S2IO_BIT_SET))
3450 val64 = readq(addr);
3451 if (bit_state == S2IO_BIT_RESET) {
3452 if (!(val64 & busy_bit)) {
3457 if (!(val64 & busy_bit)) {
3474 * check_pci_device_id - Checks if the device id is supported
3476 * Description: Function to check if the pci device id is supported by driver.
3477 * Return value: Actual device id if supported else PCI_ANY_ID
3479 static u16 check_pci_device_id(u16 id)
3482 case PCI_DEVICE_ID_HERC_WIN:
3483 case PCI_DEVICE_ID_HERC_UNI:
3484 return XFRAME_II_DEVICE;
3485 case PCI_DEVICE_ID_S2IO_UNI:
3486 case PCI_DEVICE_ID_S2IO_WIN:
3487 return XFRAME_I_DEVICE;
3494 * s2io_reset - Resets the card.
3495 * @sp : private member of the device structure.
3496 * Description: Function to Reset the card. This function then also
3497 * restores the previously saved PCI configuration space registers as
3498 * the card reset also resets the configuration space.
3503 static void s2io_reset(struct s2io_nic * sp)
3505 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3510 unsigned long long up_cnt, down_cnt, up_time, down_time, reset_cnt;
3511 unsigned long long mem_alloc_cnt, mem_free_cnt, watchdog_cnt;
3513 DBG_PRINT(INIT_DBG,"%s - Resetting XFrame card %s\n",
3514 __FUNCTION__, sp->dev->name);
3516 /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
3517 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
3519 val64 = SW_RESET_ALL;
3520 writeq(val64, &bar0->sw_reset);
3521 if (strstr(sp->product_name, "CX4")) {
3525 for (i = 0; i < S2IO_MAX_PCI_CONFIG_SPACE_REINIT; i++) {
3527 /* Restore the PCI state saved during initialization. */
3528 pci_restore_state(sp->pdev);
3529 pci_read_config_word(sp->pdev, 0x2, &val16);
3530 if (check_pci_device_id(val16) != (u16)PCI_ANY_ID)
3535 if (check_pci_device_id(val16) == (u16)PCI_ANY_ID) {
3536 DBG_PRINT(ERR_DBG,"%s SW_Reset failed!\n", __FUNCTION__);
3539 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, pci_cmd);
3543 /* Set swapper to enable I/O register access */
3544 s2io_set_swapper(sp);
3546 /* restore mac_addr entries */
3547 do_s2io_restore_unicast_mc(sp);
3549 /* Restore the MSIX table entries from local variables */
3550 restore_xmsi_data(sp);
3552 /* Clear certain PCI/PCI-X fields after reset */
3553 if (sp->device_type == XFRAME_II_DEVICE) {
3554 /* Clear "detected parity error" bit */
3555 pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000);
3557 /* Clearing PCIX Ecc status register */
3558 pci_write_config_dword(sp->pdev, 0x68, 0x7C);
3560 /* Clearing PCI_STATUS error reflected here */
3561 writeq(s2BIT(62), &bar0->txpic_int_reg);
3564 /* Reset device statistics maintained by OS */
3565 memset(&sp->stats, 0, sizeof (struct net_device_stats));
3567 up_cnt = sp->mac_control.stats_info->sw_stat.link_up_cnt;
3568 down_cnt = sp->mac_control.stats_info->sw_stat.link_down_cnt;
3569 up_time = sp->mac_control.stats_info->sw_stat.link_up_time;
3570 down_time = sp->mac_control.stats_info->sw_stat.link_down_time;
3571 reset_cnt = sp->mac_control.stats_info->sw_stat.soft_reset_cnt;
3572 mem_alloc_cnt = sp->mac_control.stats_info->sw_stat.mem_allocated;
3573 mem_free_cnt = sp->mac_control.stats_info->sw_stat.mem_freed;
3574 watchdog_cnt = sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt;
3575 /* save link up/down time/cnt, reset/memory/watchdog cnt */
3576 memset(sp->mac_control.stats_info, 0, sizeof(struct stat_block));
3577 /* restore link up/down time/cnt, reset/memory/watchdog cnt */
3578 sp->mac_control.stats_info->sw_stat.link_up_cnt = up_cnt;
3579 sp->mac_control.stats_info->sw_stat.link_down_cnt = down_cnt;
3580 sp->mac_control.stats_info->sw_stat.link_up_time = up_time;
3581 sp->mac_control.stats_info->sw_stat.link_down_time = down_time;
3582 sp->mac_control.stats_info->sw_stat.soft_reset_cnt = reset_cnt;
3583 sp->mac_control.stats_info->sw_stat.mem_allocated = mem_alloc_cnt;
3584 sp->mac_control.stats_info->sw_stat.mem_freed = mem_free_cnt;
3585 sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt = watchdog_cnt;
3587 /* SXE-002: Configure link and activity LED to turn it off */
3588 subid = sp->pdev->subsystem_device;
3589 if (((subid & 0xFF) >= 0x07) &&
3590 (sp->device_type == XFRAME_I_DEVICE)) {
3591 val64 = readq(&bar0->gpio_control);
3592 val64 |= 0x0000800000000000ULL;
3593 writeq(val64, &bar0->gpio_control);
3594 val64 = 0x0411040400000000ULL;
3595 writeq(val64, (void __iomem *)bar0 + 0x2700);
3599 * Clear spurious ECC interrupts that would have occured on
3600 * XFRAME II cards after reset.
3602 if (sp->device_type == XFRAME_II_DEVICE) {
3603 val64 = readq(&bar0->pcc_err_reg);
3604 writeq(val64, &bar0->pcc_err_reg);
3607 sp->device_enabled_once = FALSE;
3611 * s2io_set_swapper - to set the swapper controle on the card
3612 * @sp : private member of the device structure,
3613 * pointer to the s2io_nic structure.
3614 * Description: Function to set the swapper control on the card
3615 * correctly depending on the 'endianness' of the system.
3617 * SUCCESS on success and FAILURE on failure.
3620 static int s2io_set_swapper(struct s2io_nic * sp)
3622 struct net_device *dev = sp->dev;
3623 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3624 u64 val64, valt, valr;
3627 * Set proper endian settings and verify the same by reading
3628 * the PIF Feed-back register.
3631 val64 = readq(&bar0->pif_rd_swapper_fb);
3632 if (val64 != 0x0123456789ABCDEFULL) {
3634 u64 value[] = { 0xC30000C3C30000C3ULL, /* FE=1, SE=1 */
3635 0x8100008181000081ULL, /* FE=1, SE=0 */
3636 0x4200004242000042ULL, /* FE=0, SE=1 */
3637 0}; /* FE=0, SE=0 */
3640 writeq(value[i], &bar0->swapper_ctrl);
3641 val64 = readq(&bar0->pif_rd_swapper_fb);
3642 if (val64 == 0x0123456789ABCDEFULL)
3647 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, ",
3649 DBG_PRINT(ERR_DBG, "feedback read %llx\n",
3650 (unsigned long long) val64);
3655 valr = readq(&bar0->swapper_ctrl);
3658 valt = 0x0123456789ABCDEFULL;
3659 writeq(valt, &bar0->xmsi_address);
3660 val64 = readq(&bar0->xmsi_address);
3664 u64 value[] = { 0x00C3C30000C3C300ULL, /* FE=1, SE=1 */
3665 0x0081810000818100ULL, /* FE=1, SE=0 */
3666 0x0042420000424200ULL, /* FE=0, SE=1 */
3667 0}; /* FE=0, SE=0 */
3670 writeq((value[i] | valr), &bar0->swapper_ctrl);
3671 writeq(valt, &bar0->xmsi_address);
3672 val64 = readq(&bar0->xmsi_address);
3678 unsigned long long x = val64;
3679 DBG_PRINT(ERR_DBG, "Write failed, Xmsi_addr ");
3680 DBG_PRINT(ERR_DBG, "reads:0x%llx\n", x);
3684 val64 = readq(&bar0->swapper_ctrl);
3685 val64 &= 0xFFFF000000000000ULL;
3689 * The device by default set to a big endian format, so a
3690 * big endian driver need not set anything.
3692 val64 |= (SWAPPER_CTRL_TXP_FE |
3693 SWAPPER_CTRL_TXP_SE |
3694 SWAPPER_CTRL_TXD_R_FE |
3695 SWAPPER_CTRL_TXD_W_FE |
3696 SWAPPER_CTRL_TXF_R_FE |
3697 SWAPPER_CTRL_RXD_R_FE |
3698 SWAPPER_CTRL_RXD_W_FE |
3699 SWAPPER_CTRL_RXF_W_FE |
3700 SWAPPER_CTRL_XMSI_FE |
3701 SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
3702 if (sp->config.intr_type == INTA)
3703 val64 |= SWAPPER_CTRL_XMSI_SE;
3704 writeq(val64, &bar0->swapper_ctrl);
3707 * Initially we enable all bits to make it accessible by the
3708 * driver, then we selectively enable only those bits that
3711 val64 |= (SWAPPER_CTRL_TXP_FE |
3712 SWAPPER_CTRL_TXP_SE |
3713 SWAPPER_CTRL_TXD_R_FE |
3714 SWAPPER_CTRL_TXD_R_SE |
3715 SWAPPER_CTRL_TXD_W_FE |
3716 SWAPPER_CTRL_TXD_W_SE |
3717 SWAPPER_CTRL_TXF_R_FE |
3718 SWAPPER_CTRL_RXD_R_FE |
3719 SWAPPER_CTRL_RXD_R_SE |
3720 SWAPPER_CTRL_RXD_W_FE |
3721 SWAPPER_CTRL_RXD_W_SE |
3722 SWAPPER_CTRL_RXF_W_FE |
3723 SWAPPER_CTRL_XMSI_FE |
3724 SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
3725 if (sp->config.intr_type == INTA)
3726 val64 |= SWAPPER_CTRL_XMSI_SE;
3727 writeq(val64, &bar0->swapper_ctrl);
3729 val64 = readq(&bar0->swapper_ctrl);
3732 * Verifying if endian settings are accurate by reading a
3733 * feedback register.
3735 val64 = readq(&bar0->pif_rd_swapper_fb);
3736 if (val64 != 0x0123456789ABCDEFULL) {
3737 /* Endian settings are incorrect, calls for another dekko. */
3738 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, ",
3740 DBG_PRINT(ERR_DBG, "feedback read %llx\n",
3741 (unsigned long long) val64);
3748 static int wait_for_msix_trans(struct s2io_nic *nic, int i)
3750 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3752 int ret = 0, cnt = 0;
3755 val64 = readq(&bar0->xmsi_access);
3756 if (!(val64 & s2BIT(15)))
3762 DBG_PRINT(ERR_DBG, "XMSI # %d Access failed\n", i);
3769 static void restore_xmsi_data(struct s2io_nic *nic)
3771 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3775 for (i=0; i < MAX_REQUESTED_MSI_X; i++) {
3776 writeq(nic->msix_info[i].addr, &bar0->xmsi_address);
3777 writeq(nic->msix_info[i].data, &bar0->xmsi_data);
3778 val64 = (s2BIT(7) | s2BIT(15) | vBIT(i, 26, 6));
3779 writeq(val64, &bar0->xmsi_access);
3780 if (wait_for_msix_trans(nic, i)) {
3781 DBG_PRINT(ERR_DBG, "failed in %s\n", __FUNCTION__);
3787 static void store_xmsi_data(struct s2io_nic *nic)
3789 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3790 u64 val64, addr, data;
3793 /* Store and display */
3794 for (i=0; i < MAX_REQUESTED_MSI_X; i++) {
3795 val64 = (s2BIT(15) | vBIT(i, 26, 6));
3796 writeq(val64, &bar0->xmsi_access);
3797 if (wait_for_msix_trans(nic, i)) {
3798 DBG_PRINT(ERR_DBG, "failed in %s\n", __FUNCTION__);
3801 addr = readq(&bar0->xmsi_address);
3802 data = readq(&bar0->xmsi_data);
3804 nic->msix_info[i].addr = addr;
3805 nic->msix_info[i].data = data;
3810 static int s2io_enable_msi_x(struct s2io_nic *nic)
3812 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3814 u16 msi_control; /* Temp variable */
3815 int ret, i, j, msix_indx = 1;
3817 nic->entries = kcalloc(MAX_REQUESTED_MSI_X, sizeof(struct msix_entry),
3819 if (!nic->entries) {
3820 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n", \
3822 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
3825 nic->mac_control.stats_info->sw_stat.mem_allocated
3826 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3829 kcalloc(MAX_REQUESTED_MSI_X, sizeof(struct s2io_msix_entry),
3831 if (!nic->s2io_entries) {
3832 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n",
3834 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
3835 kfree(nic->entries);
3836 nic->mac_control.stats_info->sw_stat.mem_freed
3837 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3840 nic->mac_control.stats_info->sw_stat.mem_allocated
3841 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3843 for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
3844 nic->entries[i].entry = i;
3845 nic->s2io_entries[i].entry = i;
3846 nic->s2io_entries[i].arg = NULL;
3847 nic->s2io_entries[i].in_use = 0;
3850 tx_mat = readq(&bar0->tx_mat0_n[0]);
3851 for (i=0; i<nic->config.tx_fifo_num; i++, msix_indx++) {
3852 tx_mat |= TX_MAT_SET(i, msix_indx);
3853 nic->s2io_entries[msix_indx].arg = &nic->mac_control.fifos[i];
3854 nic->s2io_entries[msix_indx].type = MSIX_FIFO_TYPE;
3855 nic->s2io_entries[msix_indx].in_use = MSIX_FLG;
3857 writeq(tx_mat, &bar0->tx_mat0_n[0]);
3859 rx_mat = readq(&bar0->rx_mat);
3860 for (j = 0; j < nic->config.rx_ring_num; j++, msix_indx++) {
3861 rx_mat |= RX_MAT_SET(j, msix_indx);
3862 nic->s2io_entries[msix_indx].arg
3863 = &nic->mac_control.rings[j];
3864 nic->s2io_entries[msix_indx].type = MSIX_RING_TYPE;
3865 nic->s2io_entries[msix_indx].in_use = MSIX_FLG;
3867 writeq(rx_mat, &bar0->rx_mat);
3869 nic->avail_msix_vectors = 0;
3870 ret = pci_enable_msix(nic->pdev, nic->entries, MAX_REQUESTED_MSI_X);
3871 /* We fail init if error or we get less vectors than min required */
3872 if (ret >= (nic->config.tx_fifo_num + nic->config.rx_ring_num + 1)) {
3873 nic->avail_msix_vectors = ret;
3874 ret = pci_enable_msix(nic->pdev, nic->entries, ret);
3877 DBG_PRINT(ERR_DBG, "%s: Enabling MSIX failed\n", nic->dev->name);
3878 kfree(nic->entries);
3879 nic->mac_control.stats_info->sw_stat.mem_freed
3880 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3881 kfree(nic->s2io_entries);
3882 nic->mac_control.stats_info->sw_stat.mem_freed
3883 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3884 nic->entries = NULL;
3885 nic->s2io_entries = NULL;
3886 nic->avail_msix_vectors = 0;
3889 if (!nic->avail_msix_vectors)
3890 nic->avail_msix_vectors = MAX_REQUESTED_MSI_X;
3893 * To enable MSI-X, MSI also needs to be enabled, due to a bug
3894 * in the herc NIC. (Temp change, needs to be removed later)
3896 pci_read_config_word(nic->pdev, 0x42, &msi_control);
3897 msi_control |= 0x1; /* Enable MSI */
3898 pci_write_config_word(nic->pdev, 0x42, msi_control);
3903 /* Handle software interrupt used during MSI(X) test */
3904 static irqreturn_t s2io_test_intr(int irq, void *dev_id)
3906 struct s2io_nic *sp = dev_id;
3908 sp->msi_detected = 1;
3909 wake_up(&sp->msi_wait);
3914 /* Test interrupt path by forcing a a software IRQ */
3915 static int s2io_test_msi(struct s2io_nic *sp)
3917 struct pci_dev *pdev = sp->pdev;
3918 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3922 err = request_irq(sp->entries[1].vector, s2io_test_intr, 0,
3925 DBG_PRINT(ERR_DBG, "%s: PCI %s: cannot assign irq %d\n",
3926 sp->dev->name, pci_name(pdev), pdev->irq);
3930 init_waitqueue_head (&sp->msi_wait);
3931 sp->msi_detected = 0;
3933 saved64 = val64 = readq(&bar0->scheduled_int_ctrl);
3934 val64 |= SCHED_INT_CTRL_ONE_SHOT;
3935 val64 |= SCHED_INT_CTRL_TIMER_EN;
3936 val64 |= SCHED_INT_CTRL_INT2MSI(1);
3937 writeq(val64, &bar0->scheduled_int_ctrl);
3939 wait_event_timeout(sp->msi_wait, sp->msi_detected, HZ/10);
3941 if (!sp->msi_detected) {
3942 /* MSI(X) test failed, go back to INTx mode */
3943 DBG_PRINT(ERR_DBG, "%s: PCI %s: No interrupt was generated "
3944 "using MSI(X) during test\n", sp->dev->name,
3950 free_irq(sp->entries[1].vector, sp);
3952 writeq(saved64, &bar0->scheduled_int_ctrl);
3957 static void remove_msix_isr(struct s2io_nic *sp)
3962 for (i = 0; i < MAX_REQUESTED_MSI_X; i++) {
3963 if (sp->s2io_entries[i].in_use ==
3964 MSIX_REGISTERED_SUCCESS) {
3965 int vector = sp->entries[i].vector;
3966 void *arg = sp->s2io_entries[i].arg;
3967 free_irq(vector, arg);
3972 kfree(sp->s2io_entries);
3974 sp->s2io_entries = NULL;
3976 pci_read_config_word(sp->pdev, 0x42, &msi_control);
3977 msi_control &= 0xFFFE; /* Disable MSI */
3978 pci_write_config_word(sp->pdev, 0x42, msi_control);
3980 pci_disable_msix(sp->pdev);
3983 static void remove_inta_isr(struct s2io_nic *sp)
3985 struct net_device *dev = sp->dev;
3987 free_irq(sp->pdev->irq, dev);
3990 /* ********************************************************* *
3991 * Functions defined below concern the OS part of the driver *
3992 * ********************************************************* */
3995 * s2io_open - open entry point of the driver
3996 * @dev : pointer to the device structure.
3998 * This function is the open entry point of the driver. It mainly calls a
3999 * function to allocate Rx buffers and inserts them into the buffer
4000 * descriptors and then enables the Rx part of the NIC.
4002 * 0 on success and an appropriate (-)ve integer as defined in errno.h
4006 static int s2io_open(struct net_device *dev)
4008 struct s2io_nic *sp = dev->priv;
4012 * Make sure you have link off by default every time
4013 * Nic is initialized
4015 netif_carrier_off(dev);
4016 sp->last_link_state = 0;
4018 if (sp->config.intr_type == MSI_X) {
4019 int ret = s2io_enable_msi_x(sp);
4022 ret = s2io_test_msi(sp);
4023 /* rollback MSI-X, will re-enable during add_isr() */
4024 remove_msix_isr(sp);
4029 "%s: MSI-X requested but failed to enable\n",
4031 sp->config.intr_type = INTA;
4035 /* NAPI doesn't work well with MSI(X) */
4036 if (sp->config.intr_type != INTA) {
4038 sp->config.napi = 0;
4041 /* Initialize H/W and enable interrupts */
4042 err = s2io_card_up(sp);
4044 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
4046 goto hw_init_failed;
4049 if (do_s2io_prog_unicast(dev, dev->dev_addr) == FAILURE) {
4050 DBG_PRINT(ERR_DBG, "Set Mac Address Failed\n");
4053 goto hw_init_failed;
4055 s2io_start_all_tx_queue(sp);
4059 if (sp->config.intr_type == MSI_X) {
4062 sp->mac_control.stats_info->sw_stat.mem_freed
4063 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
4065 if (sp->s2io_entries) {
4066 kfree(sp->s2io_entries);
4067 sp->mac_control.stats_info->sw_stat.mem_freed
4068 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
4075 * s2io_close -close entry point of the driver
4076 * @dev : device pointer.
4078 * This is the stop entry point of the driver. It needs to undo exactly
4079 * whatever was done by the open entry point,thus it's usually referred to
4080 * as the close function.Among other things this function mainly stops the
4081 * Rx side of the NIC and frees all the Rx buffers in the Rx rings.
4083 * 0 on success and an appropriate (-)ve integer as defined in errno.h
4087 static int s2io_close(struct net_device *dev)
4089 struct s2io_nic *sp = dev->priv;
4090 struct config_param *config = &sp->config;
4094 /* Return if the device is already closed *
4095 * Can happen when s2io_card_up failed in change_mtu *
4097 if (!is_s2io_card_up(sp))
4100 s2io_stop_all_tx_queue(sp);
4101 /* delete all populated mac entries */
4102 for (offset = 1; offset < config->max_mc_addr; offset++) {
4103 tmp64 = do_s2io_read_unicast_mc(sp, offset);
4104 if (tmp64 != S2IO_DISABLE_MAC_ENTRY)
4105 do_s2io_delete_unicast_mc(sp, tmp64);
4108 /* Reset card, kill tasklet and free Tx and Rx buffers. */
4115 * s2io_xmit - Tx entry point of te driver
4116 * @skb : the socket buffer containing the Tx data.
4117 * @dev : device pointer.
4119 * This function is the Tx entry point of the driver. S2IO NIC supports
4120 * certain protocol assist features on Tx side, namely CSO, S/G, LSO.
4121 * NOTE: when device cant queue the pkt,just the trans_start variable will
4124 * 0 on success & 1 on failure.
4127 static int s2io_xmit(struct sk_buff *skb, struct net_device *dev)
4129 struct s2io_nic *sp = dev->priv;
4130 u16 frg_cnt, frg_len, i, queue, queue_len, put_off, get_off;
4133 struct TxFIFO_element __iomem *tx_fifo;
4134 unsigned long flags = 0;
4136 struct fifo_info *fifo = NULL;
4137 struct mac_info *mac_control;
4138 struct config_param *config;
4139 int do_spin_lock = 1;
4141 int enable_per_list_interrupt = 0;
4142 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
4144 mac_control = &sp->mac_control;
4145 config = &sp->config;
4147 DBG_PRINT(TX_DBG, "%s: In Neterion Tx routine\n", dev->name);
4149 if (unlikely(skb->len <= 0)) {
4150 DBG_PRINT(TX_DBG, "%s:Buffer has no data..\n", dev->name);
4151 dev_kfree_skb_any(skb);
4155 if (!is_s2io_card_up(sp)) {
4156 DBG_PRINT(TX_DBG, "%s: Card going down for reset\n",
4163 if (sp->vlgrp && vlan_tx_tag_present(skb))
4164 vlan_tag = vlan_tx_tag_get(skb);
4165 if (sp->config.tx_steering_type == TX_DEFAULT_STEERING) {
4166 if (skb->protocol == htons(ETH_P_IP)) {
4171 if ((ip->frag_off & htons(IP_OFFSET|IP_MF)) == 0) {
4172 th = (struct tcphdr *)(((unsigned char *)ip) +
4175 if (ip->protocol == IPPROTO_TCP) {
4176 queue_len = sp->total_tcp_fifos;
4177 queue = (ntohs(th->source) +
4179 sp->fifo_selector[queue_len - 1];
4180 if (queue >= queue_len)
4181 queue = queue_len - 1;
4182 } else if (ip->protocol == IPPROTO_UDP) {
4183 queue_len = sp->total_udp_fifos;
4184 queue = (ntohs(th->source) +
4186 sp->fifo_selector[queue_len - 1];
4187 if (queue >= queue_len)
4188 queue = queue_len - 1;
4189 queue += sp->udp_fifo_idx;
4190 if (skb->len > 1024)
4191 enable_per_list_interrupt = 1;
4196 } else if (sp->config.tx_steering_type == TX_PRIORITY_STEERING)
4197 /* get fifo number based on skb->priority value */
4198 queue = config->fifo_mapping
4199 [skb->priority & (MAX_TX_FIFOS - 1)];
4200 fifo = &mac_control->fifos[queue];
4203 spin_lock_irqsave(&fifo->tx_lock, flags);
4205 if (unlikely(!spin_trylock_irqsave(&fifo->tx_lock, flags)))
4206 return NETDEV_TX_LOCKED;
4209 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
4210 if (sp->config.multiq) {
4211 if (__netif_subqueue_stopped(dev, fifo->fifo_no)) {
4212 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4213 return NETDEV_TX_BUSY;
4217 if (unlikely(fifo->queue_state == FIFO_QUEUE_STOP)) {
4218 if (netif_queue_stopped(dev)) {
4219 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4220 return NETDEV_TX_BUSY;
4224 put_off = (u16) fifo->tx_curr_put_info.offset;
4225 get_off = (u16) fifo->tx_curr_get_info.offset;
4226 txdp = (struct TxD *) fifo->list_info[put_off].list_virt_addr;
4228 queue_len = fifo->tx_curr_put_info.fifo_len + 1;
4229 /* Avoid "put" pointer going beyond "get" pointer */
4230 if (txdp->Host_Control ||
4231 ((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4232 DBG_PRINT(TX_DBG, "Error in xmit, No free TXDs.\n");
4233 s2io_stop_tx_queue(sp, fifo->fifo_no);
4235 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4239 offload_type = s2io_offload_type(skb);
4240 if (offload_type & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6)) {
4241 txdp->Control_1 |= TXD_TCP_LSO_EN;
4242 txdp->Control_1 |= TXD_TCP_LSO_MSS(s2io_tcp_mss(skb));
4244 if (skb->ip_summed == CHECKSUM_PARTIAL) {
4246 (TXD_TX_CKO_IPV4_EN | TXD_TX_CKO_TCP_EN |
4249 txdp->Control_1 |= TXD_GATHER_CODE_FIRST;
4250 txdp->Control_1 |= TXD_LIST_OWN_XENA;
4251 txdp->Control_2 |= TXD_INT_NUMBER(fifo->fifo_no);
4252 if (enable_per_list_interrupt)
4253 if (put_off & (queue_len >> 5))
4254 txdp->Control_2 |= TXD_INT_TYPE_PER_LIST;
4256 txdp->Control_2 |= TXD_VLAN_ENABLE;
4257 txdp->Control_2 |= TXD_VLAN_TAG(vlan_tag);
4260 frg_len = skb->len - skb->data_len;
4261 if (offload_type == SKB_GSO_UDP) {
4264 ufo_size = s2io_udp_mss(skb);
4266 txdp->Control_1 |= TXD_UFO_EN;
4267 txdp->Control_1 |= TXD_UFO_MSS(ufo_size);
4268 txdp->Control_1 |= TXD_BUFFER0_SIZE(8);
4270 fifo->ufo_in_band_v[put_off] =
4271 (u64)skb_shinfo(skb)->ip6_frag_id;
4273 fifo->ufo_in_band_v[put_off] =
4274 (u64)skb_shinfo(skb)->ip6_frag_id << 32;
4276 txdp->Host_Control = (unsigned long)fifo->ufo_in_band_v;
4277 txdp->Buffer_Pointer = pci_map_single(sp->pdev,
4278 fifo->ufo_in_band_v,
4279 sizeof(u64), PCI_DMA_TODEVICE);
4280 if((txdp->Buffer_Pointer == 0) ||
4281 (txdp->Buffer_Pointer == DMA_ERROR_CODE))
4282 goto pci_map_failed;
4286 txdp->Buffer_Pointer = pci_map_single
4287 (sp->pdev, skb->data, frg_len, PCI_DMA_TODEVICE);
4288 if((txdp->Buffer_Pointer == 0) ||
4289 (txdp->Buffer_Pointer == DMA_ERROR_CODE))
4290 goto pci_map_failed;
4292 txdp->Host_Control = (unsigned long) skb;
4293 txdp->Control_1 |= TXD_BUFFER0_SIZE(frg_len);
4294 if (offload_type == SKB_GSO_UDP)
4295 txdp->Control_1 |= TXD_UFO_EN;
4297 frg_cnt = skb_shinfo(skb)->nr_frags;
4298 /* For fragmented SKB. */
4299 for (i = 0; i < frg_cnt; i++) {
4300 skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
4301 /* A '0' length fragment will be ignored */
4305 txdp->Buffer_Pointer = (u64) pci_map_page
4306 (sp->pdev, frag->page, frag->page_offset,
4307 frag->size, PCI_DMA_TODEVICE);
4308 txdp->Control_1 = TXD_BUFFER0_SIZE(frag->size);
4309 if (offload_type == SKB_GSO_UDP)
4310 txdp->Control_1 |= TXD_UFO_EN;
4312 txdp->Control_1 |= TXD_GATHER_CODE_LAST;
4314 if (offload_type == SKB_GSO_UDP)
4315 frg_cnt++; /* as Txd0 was used for inband header */
4317 tx_fifo = mac_control->tx_FIFO_start[queue];
4318 val64 = fifo->list_info[put_off].list_phy_addr;
4319 writeq(val64, &tx_fifo->TxDL_Pointer);
4321 val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
4324 val64 |= TX_FIFO_SPECIAL_FUNC;
4326 writeq(val64, &tx_fifo->List_Control);
4331 if (put_off == fifo->tx_curr_put_info.fifo_len + 1)
4333 fifo->tx_curr_put_info.offset = put_off;
4335 /* Avoid "put" pointer going beyond "get" pointer */
4336 if (((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4337 sp->mac_control.stats_info->sw_stat.fifo_full_cnt++;
4339 "No free TxDs for xmit, Put: 0x%x Get:0x%x\n",
4341 s2io_stop_tx_queue(sp, fifo->fifo_no);
4343 mac_control->stats_info->sw_stat.mem_allocated += skb->truesize;
4344 dev->trans_start = jiffies;
4345 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4349 stats->pci_map_fail_cnt++;
4350 s2io_stop_tx_queue(sp, fifo->fifo_no);
4351 stats->mem_freed += skb->truesize;
4353 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4358 s2io_alarm_handle(unsigned long data)
4360 struct s2io_nic *sp = (struct s2io_nic *)data;
4361 struct net_device *dev = sp->dev;
4363 s2io_handle_errors(dev);
4364 mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
4367 static int s2io_chk_rx_buffers(struct s2io_nic *sp, int rng_n)
4369 int rxb_size, level;
4372 rxb_size = atomic_read(&sp->rx_bufs_left[rng_n]);
4373 level = rx_buffer_level(sp, rxb_size, rng_n);
4375 if ((level == PANIC) && (!TASKLET_IN_USE)) {
4377 DBG_PRINT(INTR_DBG, "%s: Rx BD hit ", __FUNCTION__);
4378 DBG_PRINT(INTR_DBG, "PANIC levels\n");
4379 if ((ret = fill_rx_buffers(sp, rng_n)) == -ENOMEM) {
4380 DBG_PRINT(INFO_DBG, "Out of memory in %s",
4382 clear_bit(0, (&sp->tasklet_status));
4385 clear_bit(0, (&sp->tasklet_status));
4386 } else if (level == LOW)
4387 tasklet_schedule(&sp->task);
4389 } else if (fill_rx_buffers(sp, rng_n) == -ENOMEM) {
4390 DBG_PRINT(INFO_DBG, "%s:Out of memory", sp->dev->name);
4391 DBG_PRINT(INFO_DBG, " in Rx Intr!!\n");
4396 static irqreturn_t s2io_msix_ring_handle(int irq, void *dev_id)
4398 struct ring_info *ring = (struct ring_info *)dev_id;
4399 struct s2io_nic *sp = ring->nic;
4401 if (!is_s2io_card_up(sp))
4404 rx_intr_handler(ring);
4405 s2io_chk_rx_buffers(sp, ring->ring_no);
4410 static irqreturn_t s2io_msix_fifo_handle(int irq, void *dev_id)
4412 struct fifo_info *fifo = (struct fifo_info *)dev_id;
4413 struct s2io_nic *sp = fifo->nic;
4415 if (!is_s2io_card_up(sp))
4418 tx_intr_handler(fifo);
4421 static void s2io_txpic_intr_handle(struct s2io_nic *sp)
4423 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4426 val64 = readq(&bar0->pic_int_status);
4427 if (val64 & PIC_INT_GPIO) {
4428 val64 = readq(&bar0->gpio_int_reg);
4429 if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
4430 (val64 & GPIO_INT_REG_LINK_UP)) {
4432 * This is unstable state so clear both up/down
4433 * interrupt and adapter to re-evaluate the link state.
4435 val64 |= GPIO_INT_REG_LINK_DOWN;
4436 val64 |= GPIO_INT_REG_LINK_UP;
4437 writeq(val64, &bar0->gpio_int_reg);
4438 val64 = readq(&bar0->gpio_int_mask);
4439 val64 &= ~(GPIO_INT_MASK_LINK_UP |
4440 GPIO_INT_MASK_LINK_DOWN);
4441 writeq(val64, &bar0->gpio_int_mask);
4443 else if (val64 & GPIO_INT_REG_LINK_UP) {
4444 val64 = readq(&bar0->adapter_status);
4445 /* Enable Adapter */
4446 val64 = readq(&bar0->adapter_control);
4447 val64 |= ADAPTER_CNTL_EN;
4448 writeq(val64, &bar0->adapter_control);
4449 val64 |= ADAPTER_LED_ON;
4450 writeq(val64, &bar0->adapter_control);
4451 if (!sp->device_enabled_once)
4452 sp->device_enabled_once = 1;
4454 s2io_link(sp, LINK_UP);
4456 * unmask link down interrupt and mask link-up
4459 val64 = readq(&bar0->gpio_int_mask);
4460 val64 &= ~GPIO_INT_MASK_LINK_DOWN;
4461 val64 |= GPIO_INT_MASK_LINK_UP;
4462 writeq(val64, &bar0->gpio_int_mask);
4464 }else if (val64 & GPIO_INT_REG_LINK_DOWN) {
4465 val64 = readq(&bar0->adapter_status);
4466 s2io_link(sp, LINK_DOWN);
4467 /* Link is down so unmaks link up interrupt */
4468 val64 = readq(&bar0->gpio_int_mask);
4469 val64 &= ~GPIO_INT_MASK_LINK_UP;
4470 val64 |= GPIO_INT_MASK_LINK_DOWN;
4471 writeq(val64, &bar0->gpio_int_mask);
4474 val64 = readq(&bar0->adapter_control);
4475 val64 = val64 &(~ADAPTER_LED_ON);
4476 writeq(val64, &bar0->adapter_control);
4479 val64 = readq(&bar0->gpio_int_mask);
4483 * do_s2io_chk_alarm_bit - Check for alarm and incrment the counter
4484 * @value: alarm bits
4485 * @addr: address value
4486 * @cnt: counter variable
4487 * Description: Check for alarm and increment the counter
4489 * 1 - if alarm bit set
4490 * 0 - if alarm bit is not set
4492 static int do_s2io_chk_alarm_bit(u64 value, void __iomem * addr,
4493 unsigned long long *cnt)
4496 val64 = readq(addr);
4497 if ( val64 & value ) {
4498 writeq(val64, addr);
4507 * s2io_handle_errors - Xframe error indication handler
4508 * @nic: device private variable
4509 * Description: Handle alarms such as loss of link, single or
4510 * double ECC errors, critical and serious errors.
4514 static void s2io_handle_errors(void * dev_id)
4516 struct net_device *dev = (struct net_device *) dev_id;
4517 struct s2io_nic *sp = dev->priv;
4518 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4519 u64 temp64 = 0,val64=0;
4522 struct swStat *sw_stat = &sp->mac_control.stats_info->sw_stat;
4523 struct xpakStat *stats = &sp->mac_control.stats_info->xpak_stat;
4525 if (!is_s2io_card_up(sp))
4528 if (pci_channel_offline(sp->pdev))
4531 memset(&sw_stat->ring_full_cnt, 0,
4532 sizeof(sw_stat->ring_full_cnt));
4534 /* Handling the XPAK counters update */
4535 if(stats->xpak_timer_count < 72000) {
4536 /* waiting for an hour */
4537 stats->xpak_timer_count++;
4539 s2io_updt_xpak_counter(dev);
4540 /* reset the count to zero */
4541 stats->xpak_timer_count = 0;
4544 /* Handling link status change error Intr */
4545 if (s2io_link_fault_indication(sp) == MAC_RMAC_ERR_TIMER) {
4546 val64 = readq(&bar0->mac_rmac_err_reg);
4547 writeq(val64, &bar0->mac_rmac_err_reg);
4548 if (val64 & RMAC_LINK_STATE_CHANGE_INT)
4549 schedule_work(&sp->set_link_task);
4552 /* In case of a serious error, the device will be Reset. */
4553 if (do_s2io_chk_alarm_bit(SERR_SOURCE_ANY, &bar0->serr_source,
4554 &sw_stat->serious_err_cnt))
4557 /* Check for data parity error */
4558 if (do_s2io_chk_alarm_bit(GPIO_INT_REG_DP_ERR_INT, &bar0->gpio_int_reg,
4559 &sw_stat->parity_err_cnt))
4562 /* Check for ring full counter */
4563 if (sp->device_type == XFRAME_II_DEVICE) {
4564 val64 = readq(&bar0->ring_bump_counter1);
4565 for (i=0; i<4; i++) {
4566 temp64 = ( val64 & vBIT(0xFFFF,(i*16),16));
4567 temp64 >>= 64 - ((i+1)*16);
4568 sw_stat->ring_full_cnt[i] += temp64;
4571 val64 = readq(&bar0->ring_bump_counter2);
4572 for (i=0; i<4; i++) {
4573 temp64 = ( val64 & vBIT(0xFFFF,(i*16),16));
4574 temp64 >>= 64 - ((i+1)*16);
4575 sw_stat->ring_full_cnt[i+4] += temp64;
4579 val64 = readq(&bar0->txdma_int_status);
4580 /*check for pfc_err*/
4581 if (val64 & TXDMA_PFC_INT) {
4582 if (do_s2io_chk_alarm_bit(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM|
4583 PFC_MISC_0_ERR | PFC_MISC_1_ERR|
4584 PFC_PCIX_ERR, &bar0->pfc_err_reg,
4585 &sw_stat->pfc_err_cnt))
4587 do_s2io_chk_alarm_bit(PFC_ECC_SG_ERR, &bar0->pfc_err_reg,
4588 &sw_stat->pfc_err_cnt);
4591 /*check for tda_err*/
4592 if (val64 & TXDMA_TDA_INT) {
4593 if(do_s2io_chk_alarm_bit(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
4594 TDA_SM1_ERR_ALARM, &bar0->tda_err_reg,
4595 &sw_stat->tda_err_cnt))
4597 do_s2io_chk_alarm_bit(TDA_Fn_ECC_SG_ERR | TDA_PCIX_ERR,
4598 &bar0->tda_err_reg, &sw_stat->tda_err_cnt);
4600 /*check for pcc_err*/
4601 if (val64 & TXDMA_PCC_INT) {
4602 if (do_s2io_chk_alarm_bit(PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM
4603 | PCC_N_SERR | PCC_6_COF_OV_ERR
4604 | PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR
4605 | PCC_7_LSO_OV_ERR | PCC_FB_ECC_DB_ERR
4606 | PCC_TXB_ECC_DB_ERR, &bar0->pcc_err_reg,
4607 &sw_stat->pcc_err_cnt))
4609 do_s2io_chk_alarm_bit(PCC_FB_ECC_SG_ERR | PCC_TXB_ECC_SG_ERR,
4610 &bar0->pcc_err_reg, &sw_stat->pcc_err_cnt);
4613 /*check for tti_err*/
4614 if (val64 & TXDMA_TTI_INT) {
4615 if (do_s2io_chk_alarm_bit(TTI_SM_ERR_ALARM, &bar0->tti_err_reg,
4616 &sw_stat->tti_err_cnt))
4618 do_s2io_chk_alarm_bit(TTI_ECC_SG_ERR | TTI_ECC_DB_ERR,
4619 &bar0->tti_err_reg, &sw_stat->tti_err_cnt);
4622 /*check for lso_err*/
4623 if (val64 & TXDMA_LSO_INT) {
4624 if (do_s2io_chk_alarm_bit(LSO6_ABORT | LSO7_ABORT
4625 | LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM,
4626 &bar0->lso_err_reg, &sw_stat->lso_err_cnt))
4628 do_s2io_chk_alarm_bit(LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
4629 &bar0->lso_err_reg, &sw_stat->lso_err_cnt);
4632 /*check for tpa_err*/
4633 if (val64 & TXDMA_TPA_INT) {
4634 if (do_s2io_chk_alarm_bit(TPA_SM_ERR_ALARM, &bar0->tpa_err_reg,
4635 &sw_stat->tpa_err_cnt))
4637 do_s2io_chk_alarm_bit(TPA_TX_FRM_DROP, &bar0->tpa_err_reg,
4638 &sw_stat->tpa_err_cnt);
4641 /*check for sm_err*/
4642 if (val64 & TXDMA_SM_INT) {
4643 if (do_s2io_chk_alarm_bit(SM_SM_ERR_ALARM, &bar0->sm_err_reg,
4644 &sw_stat->sm_err_cnt))
4648 val64 = readq(&bar0->mac_int_status);
4649 if (val64 & MAC_INT_STATUS_TMAC_INT) {
4650 if (do_s2io_chk_alarm_bit(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR,
4651 &bar0->mac_tmac_err_reg,
4652 &sw_stat->mac_tmac_err_cnt))
4654 do_s2io_chk_alarm_bit(TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR
4655 | TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
4656 &bar0->mac_tmac_err_reg,
4657 &sw_stat->mac_tmac_err_cnt);
4660 val64 = readq(&bar0->xgxs_int_status);
4661 if (val64 & XGXS_INT_STATUS_TXGXS) {
4662 if (do_s2io_chk_alarm_bit(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR,
4663 &bar0->xgxs_txgxs_err_reg,
4664 &sw_stat->xgxs_txgxs_err_cnt))
4666 do_s2io_chk_alarm_bit(TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
4667 &bar0->xgxs_txgxs_err_reg,
4668 &sw_stat->xgxs_txgxs_err_cnt);
4671 val64 = readq(&bar0->rxdma_int_status);
4672 if (val64 & RXDMA_INT_RC_INT_M) {
4673 if (do_s2io_chk_alarm_bit(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR
4674 | RC_PRCn_SM_ERR_ALARM |RC_FTC_SM_ERR_ALARM,
4675 &bar0->rc_err_reg, &sw_stat->rc_err_cnt))
4677 do_s2io_chk_alarm_bit(RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR
4678 | RC_RDA_FAIL_WR_Rn, &bar0->rc_err_reg,
4679 &sw_stat->rc_err_cnt);
4680 if (do_s2io_chk_alarm_bit(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn
4681 | PRC_PCI_AB_F_WR_Rn, &bar0->prc_pcix_err_reg,
4682 &sw_stat->prc_pcix_err_cnt))
4684 do_s2io_chk_alarm_bit(PRC_PCI_DP_RD_Rn | PRC_PCI_DP_WR_Rn
4685 | PRC_PCI_DP_F_WR_Rn, &bar0->prc_pcix_err_reg,
4686 &sw_stat->prc_pcix_err_cnt);
4689 if (val64 & RXDMA_INT_RPA_INT_M) {
4690 if (do_s2io_chk_alarm_bit(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR,
4691 &bar0->rpa_err_reg, &sw_stat->rpa_err_cnt))
4693 do_s2io_chk_alarm_bit(RPA_ECC_SG_ERR | RPA_ECC_DB_ERR,
4694 &bar0->rpa_err_reg, &sw_stat->rpa_err_cnt);
4697 if (val64 & RXDMA_INT_RDA_INT_M) {
4698 if (do_s2io_chk_alarm_bit(RDA_RXDn_ECC_DB_ERR
4699 | RDA_FRM_ECC_DB_N_AERR | RDA_SM1_ERR_ALARM
4700 | RDA_SM0_ERR_ALARM | RDA_RXD_ECC_DB_SERR,
4701 &bar0->rda_err_reg, &sw_stat->rda_err_cnt))
4703 do_s2io_chk_alarm_bit(RDA_RXDn_ECC_SG_ERR | RDA_FRM_ECC_SG_ERR
4704 | RDA_MISC_ERR | RDA_PCIX_ERR,
4705 &bar0->rda_err_reg, &sw_stat->rda_err_cnt);
4708 if (val64 & RXDMA_INT_RTI_INT_M) {
4709 if (do_s2io_chk_alarm_bit(RTI_SM_ERR_ALARM, &bar0->rti_err_reg,
4710 &sw_stat->rti_err_cnt))
4712 do_s2io_chk_alarm_bit(RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
4713 &bar0->rti_err_reg, &sw_stat->rti_err_cnt);
4716 val64 = readq(&bar0->mac_int_status);
4717 if (val64 & MAC_INT_STATUS_RMAC_INT) {
4718 if (do_s2io_chk_alarm_bit(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR,
4719 &bar0->mac_rmac_err_reg,
4720 &sw_stat->mac_rmac_err_cnt))
4722 do_s2io_chk_alarm_bit(RMAC_UNUSED_INT|RMAC_SINGLE_ECC_ERR|
4723 RMAC_DOUBLE_ECC_ERR, &bar0->mac_rmac_err_reg,
4724 &sw_stat->mac_rmac_err_cnt);
4727 val64 = readq(&bar0->xgxs_int_status);
4728 if (val64 & XGXS_INT_STATUS_RXGXS) {
4729 if (do_s2io_chk_alarm_bit(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR,
4730 &bar0->xgxs_rxgxs_err_reg,
4731 &sw_stat->xgxs_rxgxs_err_cnt))
4735 val64 = readq(&bar0->mc_int_status);
4736 if(val64 & MC_INT_STATUS_MC_INT) {
4737 if (do_s2io_chk_alarm_bit(MC_ERR_REG_SM_ERR, &bar0->mc_err_reg,
4738 &sw_stat->mc_err_cnt))
4741 /* Handling Ecc errors */
4742 if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) {
4743 writeq(val64, &bar0->mc_err_reg);
4744 if (val64 & MC_ERR_REG_ECC_ALL_DBL) {
4745 sw_stat->double_ecc_errs++;
4746 if (sp->device_type != XFRAME_II_DEVICE) {
4748 * Reset XframeI only if critical error
4751 (MC_ERR_REG_MIRI_ECC_DB_ERR_0 |
4752 MC_ERR_REG_MIRI_ECC_DB_ERR_1))
4756 sw_stat->single_ecc_errs++;
4762 s2io_stop_all_tx_queue(sp);
4763 schedule_work(&sp->rst_timer_task);
4764 sw_stat->soft_reset_cnt++;
4769 * s2io_isr - ISR handler of the device .
4770 * @irq: the irq of the device.
4771 * @dev_id: a void pointer to the dev structure of the NIC.
4772 * Description: This function is the ISR handler of the device. It
4773 * identifies the reason for the interrupt and calls the relevant
4774 * service routines. As a contongency measure, this ISR allocates the
4775 * recv buffers, if their numbers are below the panic value which is
4776 * presently set to 25% of the original number of rcv buffers allocated.
4778 * IRQ_HANDLED: will be returned if IRQ was handled by this routine
4779 * IRQ_NONE: will be returned if interrupt is not from our device
4781 static irqreturn_t s2io_isr(int irq, void *dev_id)
4783 struct net_device *dev = (struct net_device *) dev_id;
4784 struct s2io_nic *sp = dev->priv;
4785 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4788 struct mac_info *mac_control;
4789 struct config_param *config;
4791 /* Pretend we handled any irq's from a disconnected card */
4792 if (pci_channel_offline(sp->pdev))
4795 if (!is_s2io_card_up(sp))
4798 mac_control = &sp->mac_control;
4799 config = &sp->config;
4802 * Identify the cause for interrupt and call the appropriate
4803 * interrupt handler. Causes for the interrupt could be;
4808 reason = readq(&bar0->general_int_status);
4810 if (unlikely(reason == S2IO_MINUS_ONE) ) {
4811 /* Nothing much can be done. Get out */
4815 if (reason & (GEN_INTR_RXTRAFFIC |
4816 GEN_INTR_TXTRAFFIC | GEN_INTR_TXPIC))
4818 writeq(S2IO_MINUS_ONE, &bar0->general_int_mask);
4821 if (reason & GEN_INTR_RXTRAFFIC) {
4822 if (likely(netif_rx_schedule_prep(dev,
4824 __netif_rx_schedule(dev, &sp->napi);
4825 writeq(S2IO_MINUS_ONE,
4826 &bar0->rx_traffic_mask);
4828 writeq(S2IO_MINUS_ONE,
4829 &bar0->rx_traffic_int);
4833 * rx_traffic_int reg is an R1 register, writing all 1's
4834 * will ensure that the actual interrupt causing bit
4835 * get's cleared and hence a read can be avoided.
4837 if (reason & GEN_INTR_RXTRAFFIC)
4838 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
4840 for (i = 0; i < config->rx_ring_num; i++)
4841 rx_intr_handler(&mac_control->rings[i]);
4845 * tx_traffic_int reg is an R1 register, writing all 1's
4846 * will ensure that the actual interrupt causing bit get's
4847 * cleared and hence a read can be avoided.
4849 if (reason & GEN_INTR_TXTRAFFIC)
4850 writeq(S2IO_MINUS_ONE, &bar0->tx_traffic_int);
4852 for (i = 0; i < config->tx_fifo_num; i++)
4853 tx_intr_handler(&mac_control->fifos[i]);
4855 if (reason & GEN_INTR_TXPIC)
4856 s2io_txpic_intr_handle(sp);
4859 * Reallocate the buffers from the interrupt handler itself.
4861 if (!config->napi) {
4862 for (i = 0; i < config->rx_ring_num; i++)
4863 s2io_chk_rx_buffers(sp, i);
4865 writeq(sp->general_int_mask, &bar0->general_int_mask);
4866 readl(&bar0->general_int_status);
4872 /* The interrupt was not raised by us */
4882 static void s2io_updt_stats(struct s2io_nic *sp)
4884 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4888 if (is_s2io_card_up(sp)) {
4889 /* Apprx 30us on a 133 MHz bus */
4890 val64 = SET_UPDT_CLICKS(10) |
4891 STAT_CFG_ONE_SHOT_EN | STAT_CFG_STAT_EN;
4892 writeq(val64, &bar0->stat_cfg);
4895 val64 = readq(&bar0->stat_cfg);
4896 if (!(val64 & s2BIT(0)))
4900 break; /* Updt failed */
4906 * s2io_get_stats - Updates the device statistics structure.
4907 * @dev : pointer to the device structure.
4909 * This function updates the device statistics structure in the s2io_nic
4910 * structure and returns a pointer to the same.
4912 * pointer to the updated net_device_stats structure.
4915 static struct net_device_stats *s2io_get_stats(struct net_device *dev)
4917 struct s2io_nic *sp = dev->priv;
4918 struct mac_info *mac_control;
4919 struct config_param *config;
4922 mac_control = &sp->mac_control;
4923 config = &sp->config;
4925 /* Configure Stats for immediate updt */
4926 s2io_updt_stats(sp);
4928 sp->stats.tx_packets =
4929 le32_to_cpu(mac_control->stats_info->tmac_frms);
4930 sp->stats.tx_errors =
4931 le32_to_cpu(mac_control->stats_info->tmac_any_err_frms);
4932 sp->stats.rx_errors =
4933 le64_to_cpu(mac_control->stats_info->rmac_drop_frms);
4934 sp->stats.multicast =
4935 le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms);
4936 sp->stats.rx_length_errors =
4937 le64_to_cpu(mac_control->stats_info->rmac_long_frms);
4939 return (&sp->stats);
4943 * s2io_set_multicast - entry point for multicast address enable/disable.
4944 * @dev : pointer to the device structure
4946 * This function is a driver entry point which gets called by the kernel
4947 * whenever multicast addresses must be enabled/disabled. This also gets
4948 * called to set/reset promiscuous mode. Depending on the deivce flag, we
4949 * determine, if multicast address must be enabled or if promiscuous mode
4950 * is to be disabled etc.
4955 static void s2io_set_multicast(struct net_device *dev)
4958 struct dev_mc_list *mclist;
4959 struct s2io_nic *sp = dev->priv;
4960 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4961 u64 val64 = 0, multi_mac = 0x010203040506ULL, mask =
4963 u64 dis_addr = S2IO_DISABLE_MAC_ENTRY, mac_addr = 0;
4965 struct config_param *config = &sp->config;
4967 if ((dev->flags & IFF_ALLMULTI) && (!sp->m_cast_flg)) {
4968 /* Enable all Multicast addresses */
4969 writeq(RMAC_ADDR_DATA0_MEM_ADDR(multi_mac),
4970 &bar0->rmac_addr_data0_mem);
4971 writeq(RMAC_ADDR_DATA1_MEM_MASK(mask),
4972 &bar0->rmac_addr_data1_mem);
4973 val64 = RMAC_ADDR_CMD_MEM_WE |
4974 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4975 RMAC_ADDR_CMD_MEM_OFFSET(config->max_mc_addr - 1);
4976 writeq(val64, &bar0->rmac_addr_cmd_mem);
4977 /* Wait till command completes */
4978 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4979 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4983 sp->all_multi_pos = config->max_mc_addr - 1;
4984 } else if ((dev->flags & IFF_ALLMULTI) && (sp->m_cast_flg)) {
4985 /* Disable all Multicast addresses */
4986 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
4987 &bar0->rmac_addr_data0_mem);
4988 writeq(RMAC_ADDR_DATA1_MEM_MASK(0x0),
4989 &bar0->rmac_addr_data1_mem);
4990 val64 = RMAC_ADDR_CMD_MEM_WE |
4991 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4992 RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
4993 writeq(val64, &bar0->rmac_addr_cmd_mem);
4994 /* Wait till command completes */
4995 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4996 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5000 sp->all_multi_pos = 0;
5003 if ((dev->flags & IFF_PROMISC) && (!sp->promisc_flg)) {
5004 /* Put the NIC into promiscuous mode */
5005 add = &bar0->mac_cfg;
5006 val64 = readq(&bar0->mac_cfg);
5007 val64 |= MAC_CFG_RMAC_PROM_ENABLE;
5009 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5010 writel((u32) val64, add);
5011 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5012 writel((u32) (val64 >> 32), (add + 4));
5014 if (vlan_tag_strip != 1) {
5015 val64 = readq(&bar0->rx_pa_cfg);
5016 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
5017 writeq(val64, &bar0->rx_pa_cfg);
5018 vlan_strip_flag = 0;
5021 val64 = readq(&bar0->mac_cfg);
5022 sp->promisc_flg = 1;
5023 DBG_PRINT(INFO_DBG, "%s: entered promiscuous mode\n",
5025 } else if (!(dev->flags & IFF_PROMISC) && (sp->promisc_flg)) {
5026 /* Remove the NIC from promiscuous mode */
5027 add = &bar0->mac_cfg;
5028 val64 = readq(&bar0->mac_cfg);
5029 val64 &= ~MAC_CFG_RMAC_PROM_ENABLE;
5031 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5032 writel((u32) val64, add);
5033 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5034 writel((u32) (val64 >> 32), (add + 4));
5036 if (vlan_tag_strip != 0) {
5037 val64 = readq(&bar0->rx_pa_cfg);
5038 val64 |= RX_PA_CFG_STRIP_VLAN_TAG;
5039 writeq(val64, &bar0->rx_pa_cfg);
5040 vlan_strip_flag = 1;
5043 val64 = readq(&bar0->mac_cfg);
5044 sp->promisc_flg = 0;
5045 DBG_PRINT(INFO_DBG, "%s: left promiscuous mode\n",
5049 /* Update individual M_CAST address list */
5050 if ((!sp->m_cast_flg) && dev->mc_count) {
5052 (config->max_mc_addr - config->max_mac_addr)) {
5053 DBG_PRINT(ERR_DBG, "%s: No more Rx filters ",
5055 DBG_PRINT(ERR_DBG, "can be added, please enable ");
5056 DBG_PRINT(ERR_DBG, "ALL_MULTI instead\n");
5060 prev_cnt = sp->mc_addr_count;
5061 sp->mc_addr_count = dev->mc_count;
5063 /* Clear out the previous list of Mc in the H/W. */
5064 for (i = 0; i < prev_cnt; i++) {
5065 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
5066 &bar0->rmac_addr_data0_mem);
5067 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
5068 &bar0->rmac_addr_data1_mem);
5069 val64 = RMAC_ADDR_CMD_MEM_WE |
5070 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5071 RMAC_ADDR_CMD_MEM_OFFSET
5072 (config->mc_start_offset + i);
5073 writeq(val64, &bar0->rmac_addr_cmd_mem);
5075 /* Wait for command completes */
5076 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5077 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5079 DBG_PRINT(ERR_DBG, "%s: Adding ",
5081 DBG_PRINT(ERR_DBG, "Multicasts failed\n");
5086 /* Create the new Rx filter list and update the same in H/W. */
5087 for (i = 0, mclist = dev->mc_list; i < dev->mc_count;
5088 i++, mclist = mclist->next) {
5089 memcpy(sp->usr_addrs[i].addr, mclist->dmi_addr,
5092 for (j = 0; j < ETH_ALEN; j++) {
5093 mac_addr |= mclist->dmi_addr[j];
5097 writeq(RMAC_ADDR_DATA0_MEM_ADDR(mac_addr),
5098 &bar0->rmac_addr_data0_mem);
5099 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
5100 &bar0->rmac_addr_data1_mem);
5101 val64 = RMAC_ADDR_CMD_MEM_WE |
5102 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5103 RMAC_ADDR_CMD_MEM_OFFSET
5104 (i + config->mc_start_offset);
5105 writeq(val64, &bar0->rmac_addr_cmd_mem);
5107 /* Wait for command completes */
5108 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5109 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5111 DBG_PRINT(ERR_DBG, "%s: Adding ",
5113 DBG_PRINT(ERR_DBG, "Multicasts failed\n");
5120 /* read from CAM unicast & multicast addresses and store it in
5121 * def_mac_addr structure
5123 void do_s2io_store_unicast_mc(struct s2io_nic *sp)
5127 struct config_param *config = &sp->config;
5129 /* store unicast & multicast mac addresses */
5130 for (offset = 0; offset < config->max_mc_addr; offset++) {
5131 mac_addr = do_s2io_read_unicast_mc(sp, offset);
5132 /* if read fails disable the entry */
5133 if (mac_addr == FAILURE)
5134 mac_addr = S2IO_DISABLE_MAC_ENTRY;
5135 do_s2io_copy_mac_addr(sp, offset, mac_addr);
5139 /* restore unicast & multicast MAC to CAM from def_mac_addr structure */
5140 static void do_s2io_restore_unicast_mc(struct s2io_nic *sp)
5143 struct config_param *config = &sp->config;
5144 /* restore unicast mac address */
5145 for (offset = 0; offset < config->max_mac_addr; offset++)
5146 do_s2io_prog_unicast(sp->dev,
5147 sp->def_mac_addr[offset].mac_addr);
5149 /* restore multicast mac address */
5150 for (offset = config->mc_start_offset;
5151 offset < config->max_mc_addr; offset++)
5152 do_s2io_add_mc(sp, sp->def_mac_addr[offset].mac_addr);
5155 /* add a multicast MAC address to CAM */
5156 static int do_s2io_add_mc(struct s2io_nic *sp, u8 *addr)
5160 struct config_param *config = &sp->config;
5162 for (i = 0; i < ETH_ALEN; i++) {
5164 mac_addr |= addr[i];
5166 if ((0ULL == mac_addr) || (mac_addr == S2IO_DISABLE_MAC_ENTRY))
5169 /* check if the multicast mac already preset in CAM */
5170 for (i = config->mc_start_offset; i < config->max_mc_addr; i++) {
5172 tmp64 = do_s2io_read_unicast_mc(sp, i);
5173 if (tmp64 == S2IO_DISABLE_MAC_ENTRY) /* CAM entry is empty */
5176 if (tmp64 == mac_addr)
5179 if (i == config->max_mc_addr) {
5181 "CAM full no space left for multicast MAC\n");
5184 /* Update the internal structure with this new mac address */
5185 do_s2io_copy_mac_addr(sp, i, mac_addr);
5187 return (do_s2io_add_mac(sp, mac_addr, i));
5190 /* add MAC address to CAM */
5191 static int do_s2io_add_mac(struct s2io_nic *sp, u64 addr, int off)
5194 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5196 writeq(RMAC_ADDR_DATA0_MEM_ADDR(addr),
5197 &bar0->rmac_addr_data0_mem);
5200 RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5201 RMAC_ADDR_CMD_MEM_OFFSET(off);
5202 writeq(val64, &bar0->rmac_addr_cmd_mem);
5204 /* Wait till command completes */
5205 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5206 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5208 DBG_PRINT(INFO_DBG, "do_s2io_add_mac failed\n");
5213 /* deletes a specified unicast/multicast mac entry from CAM */
5214 static int do_s2io_delete_unicast_mc(struct s2io_nic *sp, u64 addr)
5217 u64 dis_addr = S2IO_DISABLE_MAC_ENTRY, tmp64;
5218 struct config_param *config = &sp->config;
5221 offset < config->max_mc_addr; offset++) {
5222 tmp64 = do_s2io_read_unicast_mc(sp, offset);
5223 if (tmp64 == addr) {
5224 /* disable the entry by writing 0xffffffffffffULL */
5225 if (do_s2io_add_mac(sp, dis_addr, offset) == FAILURE)
5227 /* store the new mac list from CAM */
5228 do_s2io_store_unicast_mc(sp);
5232 DBG_PRINT(ERR_DBG, "MAC address 0x%llx not found in CAM\n",
5233 (unsigned long long)addr);
5237 /* read mac entries from CAM */
5238 static u64 do_s2io_read_unicast_mc(struct s2io_nic *sp, int offset)
5240 u64 tmp64 = 0xffffffffffff0000ULL, val64;
5241 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5245 RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5246 RMAC_ADDR_CMD_MEM_OFFSET(offset);
5247 writeq(val64, &bar0->rmac_addr_cmd_mem);
5249 /* Wait till command completes */
5250 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5251 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5253 DBG_PRINT(INFO_DBG, "do_s2io_read_unicast_mc failed\n");
5256 tmp64 = readq(&bar0->rmac_addr_data0_mem);
5257 return (tmp64 >> 16);
5261 * s2io_set_mac_addr driver entry point
5264 static int s2io_set_mac_addr(struct net_device *dev, void *p)
5266 struct sockaddr *addr = p;
5268 if (!is_valid_ether_addr(addr->sa_data))
5271 memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
5273 /* store the MAC address in CAM */
5274 return (do_s2io_prog_unicast(dev, dev->dev_addr));
5277 * do_s2io_prog_unicast - Programs the Xframe mac address
5278 * @dev : pointer to the device structure.
5279 * @addr: a uchar pointer to the new mac address which is to be set.
5280 * Description : This procedure will program the Xframe to receive
5281 * frames with new Mac Address
5282 * Return value: SUCCESS on success and an appropriate (-)ve integer
5283 * as defined in errno.h file on failure.
5286 static int do_s2io_prog_unicast(struct net_device *dev, u8 *addr)
5288 struct s2io_nic *sp = dev->priv;
5289 register u64 mac_addr = 0, perm_addr = 0;
5292 struct config_param *config = &sp->config;
5295 * Set the new MAC address as the new unicast filter and reflect this
5296 * change on the device address registered with the OS. It will be
5299 for (i = 0; i < ETH_ALEN; i++) {
5301 mac_addr |= addr[i];
5303 perm_addr |= sp->def_mac_addr[0].mac_addr[i];
5306 /* check if the dev_addr is different than perm_addr */
5307 if (mac_addr == perm_addr)
5310 /* check if the mac already preset in CAM */
5311 for (i = 1; i < config->max_mac_addr; i++) {
5312 tmp64 = do_s2io_read_unicast_mc(sp, i);
5313 if (tmp64 == S2IO_DISABLE_MAC_ENTRY) /* CAM entry is empty */
5316 if (tmp64 == mac_addr) {
5318 "MAC addr:0x%llx already present in CAM\n",
5319 (unsigned long long)mac_addr);
5323 if (i == config->max_mac_addr) {
5324 DBG_PRINT(ERR_DBG, "CAM full no space left for Unicast MAC\n");
5327 /* Update the internal structure with this new mac address */
5328 do_s2io_copy_mac_addr(sp, i, mac_addr);
5329 return (do_s2io_add_mac(sp, mac_addr, i));
5333 * s2io_ethtool_sset - Sets different link parameters.
5334 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5335 * @info: pointer to the structure with parameters given by ethtool to set
5338 * The function sets different link parameters provided by the user onto
5344 static int s2io_ethtool_sset(struct net_device *dev,
5345 struct ethtool_cmd *info)
5347 struct s2io_nic *sp = dev->priv;
5348 if ((info->autoneg == AUTONEG_ENABLE) ||
5349 (info->speed != SPEED_10000) || (info->duplex != DUPLEX_FULL))
5352 s2io_close(sp->dev);
5360 * s2io_ethtol_gset - Return link specific information.
5361 * @sp : private member of the device structure, pointer to the
5362 * s2io_nic structure.
5363 * @info : pointer to the structure with parameters given by ethtool
5364 * to return link information.
5366 * Returns link specific information like speed, duplex etc.. to ethtool.
5368 * return 0 on success.
5371 static int s2io_ethtool_gset(struct net_device *dev, struct ethtool_cmd *info)
5373 struct s2io_nic *sp = dev->priv;
5374 info->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
5375 info->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
5376 info->port = PORT_FIBRE;
5378 /* info->transceiver */
5379 info->transceiver = XCVR_EXTERNAL;
5381 if (netif_carrier_ok(sp->dev)) {
5382 info->speed = 10000;
5383 info->duplex = DUPLEX_FULL;
5389 info->autoneg = AUTONEG_DISABLE;
5394 * s2io_ethtool_gdrvinfo - Returns driver specific information.
5395 * @sp : private member of the device structure, which is a pointer to the
5396 * s2io_nic structure.
5397 * @info : pointer to the structure with parameters given by ethtool to
5398 * return driver information.
5400 * Returns driver specefic information like name, version etc.. to ethtool.
5405 static void s2io_ethtool_gdrvinfo(struct net_device *dev,
5406 struct ethtool_drvinfo *info)
5408 struct s2io_nic *sp = dev->priv;
5410 strncpy(info->driver, s2io_driver_name, sizeof(info->driver));
5411 strncpy(info->version, s2io_driver_version, sizeof(info->version));
5412 strncpy(info->fw_version, "", sizeof(info->fw_version));
5413 strncpy(info->bus_info, pci_name(sp->pdev), sizeof(info->bus_info));
5414 info->regdump_len = XENA_REG_SPACE;
5415 info->eedump_len = XENA_EEPROM_SPACE;
5419 * s2io_ethtool_gregs - dumps the entire space of Xfame into the buffer.
5420 * @sp: private member of the device structure, which is a pointer to the
5421 * s2io_nic structure.
5422 * @regs : pointer to the structure with parameters given by ethtool for
5423 * dumping the registers.
5424 * @reg_space: The input argumnet into which all the registers are dumped.
5426 * Dumps the entire register space of xFrame NIC into the user given
5432 static void s2io_ethtool_gregs(struct net_device *dev,
5433 struct ethtool_regs *regs, void *space)
5437 u8 *reg_space = (u8 *) space;
5438 struct s2io_nic *sp = dev->priv;
5440 regs->len = XENA_REG_SPACE;
5441 regs->version = sp->pdev->subsystem_device;
5443 for (i = 0; i < regs->len; i += 8) {
5444 reg = readq(sp->bar0 + i);
5445 memcpy((reg_space + i), ®, 8);
5450 * s2io_phy_id - timer function that alternates adapter LED.
5451 * @data : address of the private member of the device structure, which
5452 * is a pointer to the s2io_nic structure, provided as an u32.
5453 * Description: This is actually the timer function that alternates the
5454 * adapter LED bit of the adapter control bit to set/reset every time on
5455 * invocation. The timer is set for 1/2 a second, hence tha NIC blinks
5456 * once every second.
5458 static void s2io_phy_id(unsigned long data)
5460 struct s2io_nic *sp = (struct s2io_nic *) data;
5461 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5465 subid = sp->pdev->subsystem_device;
5466 if ((sp->device_type == XFRAME_II_DEVICE) ||
5467 ((subid & 0xFF) >= 0x07)) {
5468 val64 = readq(&bar0->gpio_control);
5469 val64 ^= GPIO_CTRL_GPIO_0;
5470 writeq(val64, &bar0->gpio_control);
5472 val64 = readq(&bar0->adapter_control);
5473 val64 ^= ADAPTER_LED_ON;
5474 writeq(val64, &bar0->adapter_control);
5477 mod_timer(&sp->id_timer, jiffies + HZ / 2);
5481 * s2io_ethtool_idnic - To physically identify the nic on the system.
5482 * @sp : private member of the device structure, which is a pointer to the
5483 * s2io_nic structure.
5484 * @id : pointer to the structure with identification parameters given by
5486 * Description: Used to physically identify the NIC on the system.
5487 * The Link LED will blink for a time specified by the user for
5489 * NOTE: The Link has to be Up to be able to blink the LED. Hence
5490 * identification is possible only if it's link is up.
5492 * int , returns 0 on success
5495 static int s2io_ethtool_idnic(struct net_device *dev, u32 data)
5497 u64 val64 = 0, last_gpio_ctrl_val;
5498 struct s2io_nic *sp = dev->priv;
5499 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5502 subid = sp->pdev->subsystem_device;
5503 last_gpio_ctrl_val = readq(&bar0->gpio_control);
5504 if ((sp->device_type == XFRAME_I_DEVICE) &&
5505 ((subid & 0xFF) < 0x07)) {
5506 val64 = readq(&bar0->adapter_control);
5507 if (!(val64 & ADAPTER_CNTL_EN)) {
5509 "Adapter Link down, cannot blink LED\n");
5513 if (sp->id_timer.function == NULL) {
5514 init_timer(&sp->id_timer);
5515 sp->id_timer.function = s2io_phy_id;
5516 sp->id_timer.data = (unsigned long) sp;
5518 mod_timer(&sp->id_timer, jiffies);
5520 msleep_interruptible(data * HZ);
5522 msleep_interruptible(MAX_FLICKER_TIME);
5523 del_timer_sync(&sp->id_timer);
5525 if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid)) {
5526 writeq(last_gpio_ctrl_val, &bar0->gpio_control);
5527 last_gpio_ctrl_val = readq(&bar0->gpio_control);
5533 static void s2io_ethtool_gringparam(struct net_device *dev,
5534 struct ethtool_ringparam *ering)
5536 struct s2io_nic *sp = dev->priv;
5537 int i,tx_desc_count=0,rx_desc_count=0;
5539 if (sp->rxd_mode == RXD_MODE_1)
5540 ering->rx_max_pending = MAX_RX_DESC_1;
5541 else if (sp->rxd_mode == RXD_MODE_3B)
5542 ering->rx_max_pending = MAX_RX_DESC_2;
5544 ering->tx_max_pending = MAX_TX_DESC;
5545 for (i = 0 ; i < sp->config.tx_fifo_num ; i++)
5546 tx_desc_count += sp->config.tx_cfg[i].fifo_len;
5548 DBG_PRINT(INFO_DBG,"\nmax txds : %d\n",sp->config.max_txds);
5549 ering->tx_pending = tx_desc_count;
5551 for (i = 0 ; i < sp->config.rx_ring_num ; i++)
5552 rx_desc_count += sp->config.rx_cfg[i].num_rxd;
5554 ering->rx_pending = rx_desc_count;
5556 ering->rx_mini_max_pending = 0;
5557 ering->rx_mini_pending = 0;
5558 if(sp->rxd_mode == RXD_MODE_1)
5559 ering->rx_jumbo_max_pending = MAX_RX_DESC_1;
5560 else if (sp->rxd_mode == RXD_MODE_3B)
5561 ering->rx_jumbo_max_pending = MAX_RX_DESC_2;
5562 ering->rx_jumbo_pending = rx_desc_count;
5566 * s2io_ethtool_getpause_data -Pause frame frame generation and reception.
5567 * @sp : private member of the device structure, which is a pointer to the
5568 * s2io_nic structure.
5569 * @ep : pointer to the structure with pause parameters given by ethtool.
5571 * Returns the Pause frame generation and reception capability of the NIC.
5575 static void s2io_ethtool_getpause_data(struct net_device *dev,
5576 struct ethtool_pauseparam *ep)
5579 struct s2io_nic *sp = dev->priv;
5580 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5582 val64 = readq(&bar0->rmac_pause_cfg);
5583 if (val64 & RMAC_PAUSE_GEN_ENABLE)
5584 ep->tx_pause = TRUE;
5585 if (val64 & RMAC_PAUSE_RX_ENABLE)
5586 ep->rx_pause = TRUE;
5587 ep->autoneg = FALSE;
5591 * s2io_ethtool_setpause_data - set/reset pause frame generation.
5592 * @sp : private member of the device structure, which is a pointer to the
5593 * s2io_nic structure.
5594 * @ep : pointer to the structure with pause parameters given by ethtool.
5596 * It can be used to set or reset Pause frame generation or reception
5597 * support of the NIC.
5599 * int, returns 0 on Success
5602 static int s2io_ethtool_setpause_data(struct net_device *dev,
5603 struct ethtool_pauseparam *ep)
5606 struct s2io_nic *sp = dev->priv;
5607 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5609 val64 = readq(&bar0->rmac_pause_cfg);
5611 val64 |= RMAC_PAUSE_GEN_ENABLE;
5613 val64 &= ~RMAC_PAUSE_GEN_ENABLE;
5615 val64 |= RMAC_PAUSE_RX_ENABLE;
5617 val64 &= ~RMAC_PAUSE_RX_ENABLE;
5618 writeq(val64, &bar0->rmac_pause_cfg);
5623 * read_eeprom - reads 4 bytes of data from user given offset.
5624 * @sp : private member of the device structure, which is a pointer to the
5625 * s2io_nic structure.
5626 * @off : offset at which the data must be written
5627 * @data : Its an output parameter where the data read at the given
5630 * Will read 4 bytes of data from the user given offset and return the
5632 * NOTE: Will allow to read only part of the EEPROM visible through the
5635 * -1 on failure and 0 on success.
5638 #define S2IO_DEV_ID 5
5639 static int read_eeprom(struct s2io_nic * sp, int off, u64 * data)
5644 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5646 if (sp->device_type == XFRAME_I_DEVICE) {
5647 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) | I2C_CONTROL_ADDR(off) |
5648 I2C_CONTROL_BYTE_CNT(0x3) | I2C_CONTROL_READ |
5649 I2C_CONTROL_CNTL_START;
5650 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5652 while (exit_cnt < 5) {
5653 val64 = readq(&bar0->i2c_control);
5654 if (I2C_CONTROL_CNTL_END(val64)) {
5655 *data = I2C_CONTROL_GET_DATA(val64);
5664 if (sp->device_type == XFRAME_II_DEVICE) {
5665 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5666 SPI_CONTROL_BYTECNT(0x3) |
5667 SPI_CONTROL_CMD(0x3) | SPI_CONTROL_ADDR(off);
5668 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5669 val64 |= SPI_CONTROL_REQ;
5670 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5671 while (exit_cnt < 5) {
5672 val64 = readq(&bar0->spi_control);
5673 if (val64 & SPI_CONTROL_NACK) {
5676 } else if (val64 & SPI_CONTROL_DONE) {
5677 *data = readq(&bar0->spi_data);
5690 * write_eeprom - actually writes the relevant part of the data value.
5691 * @sp : private member of the device structure, which is a pointer to the
5692 * s2io_nic structure.
5693 * @off : offset at which the data must be written
5694 * @data : The data that is to be written
5695 * @cnt : Number of bytes of the data that are actually to be written into
5696 * the Eeprom. (max of 3)
5698 * Actually writes the relevant part of the data value into the Eeprom
5699 * through the I2C bus.
5701 * 0 on success, -1 on failure.
5704 static int write_eeprom(struct s2io_nic * sp, int off, u64 data, int cnt)
5706 int exit_cnt = 0, ret = -1;
5708 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5710 if (sp->device_type == XFRAME_I_DEVICE) {
5711 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) | I2C_CONTROL_ADDR(off) |
5712 I2C_CONTROL_BYTE_CNT(cnt) | I2C_CONTROL_SET_DATA((u32)data) |
5713 I2C_CONTROL_CNTL_START;
5714 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5716 while (exit_cnt < 5) {
5717 val64 = readq(&bar0->i2c_control);
5718 if (I2C_CONTROL_CNTL_END(val64)) {
5719 if (!(val64 & I2C_CONTROL_NACK))
5728 if (sp->device_type == XFRAME_II_DEVICE) {
5729 int write_cnt = (cnt == 8) ? 0 : cnt;
5730 writeq(SPI_DATA_WRITE(data,(cnt<<3)), &bar0->spi_data);
5732 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5733 SPI_CONTROL_BYTECNT(write_cnt) |
5734 SPI_CONTROL_CMD(0x2) | SPI_CONTROL_ADDR(off);
5735 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5736 val64 |= SPI_CONTROL_REQ;
5737 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5738 while (exit_cnt < 5) {
5739 val64 = readq(&bar0->spi_control);
5740 if (val64 & SPI_CONTROL_NACK) {
5743 } else if (val64 & SPI_CONTROL_DONE) {
5753 static void s2io_vpd_read(struct s2io_nic *nic)
5757 int i=0, cnt, fail = 0;
5758 int vpd_addr = 0x80;
5760 if (nic->device_type == XFRAME_II_DEVICE) {
5761 strcpy(nic->product_name, "Xframe II 10GbE network adapter");
5765 strcpy(nic->product_name, "Xframe I 10GbE network adapter");
5768 strcpy(nic->serial_num, "NOT AVAILABLE");
5770 vpd_data = kmalloc(256, GFP_KERNEL);
5772 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
5775 nic->mac_control.stats_info->sw_stat.mem_allocated += 256;
5777 for (i = 0; i < 256; i +=4 ) {
5778 pci_write_config_byte(nic->pdev, (vpd_addr + 2), i);
5779 pci_read_config_byte(nic->pdev, (vpd_addr + 2), &data);
5780 pci_write_config_byte(nic->pdev, (vpd_addr + 3), 0);
5781 for (cnt = 0; cnt <5; cnt++) {
5783 pci_read_config_byte(nic->pdev, (vpd_addr + 3), &data);
5788 DBG_PRINT(ERR_DBG, "Read of VPD data failed\n");
5792 pci_read_config_dword(nic->pdev, (vpd_addr + 4),
5793 (u32 *)&vpd_data[i]);
5797 /* read serial number of adapter */
5798 for (cnt = 0; cnt < 256; cnt++) {
5799 if ((vpd_data[cnt] == 'S') &&
5800 (vpd_data[cnt+1] == 'N') &&
5801 (vpd_data[cnt+2] < VPD_STRING_LEN)) {
5802 memset(nic->serial_num, 0, VPD_STRING_LEN);
5803 memcpy(nic->serial_num, &vpd_data[cnt + 3],
5810 if ((!fail) && (vpd_data[1] < VPD_STRING_LEN)) {
5811 memset(nic->product_name, 0, vpd_data[1]);
5812 memcpy(nic->product_name, &vpd_data[3], vpd_data[1]);
5815 nic->mac_control.stats_info->sw_stat.mem_freed += 256;
5819 * s2io_ethtool_geeprom - reads the value stored in the Eeprom.
5820 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5821 * @eeprom : pointer to the user level structure provided by ethtool,
5822 * containing all relevant information.
5823 * @data_buf : user defined value to be written into Eeprom.
5824 * Description: Reads the values stored in the Eeprom at given offset
5825 * for a given length. Stores these values int the input argument data
5826 * buffer 'data_buf' and returns these to the caller (ethtool.)
5831 static int s2io_ethtool_geeprom(struct net_device *dev,
5832 struct ethtool_eeprom *eeprom, u8 * data_buf)
5836 struct s2io_nic *sp = dev->priv;
5838 eeprom->magic = sp->pdev->vendor | (sp->pdev->device << 16);
5840 if ((eeprom->offset + eeprom->len) > (XENA_EEPROM_SPACE))
5841 eeprom->len = XENA_EEPROM_SPACE - eeprom->offset;
5843 for (i = 0; i < eeprom->len; i += 4) {
5844 if (read_eeprom(sp, (eeprom->offset + i), &data)) {
5845 DBG_PRINT(ERR_DBG, "Read of EEPROM failed\n");
5849 memcpy((data_buf + i), &valid, 4);
5855 * s2io_ethtool_seeprom - tries to write the user provided value in Eeprom
5856 * @sp : private member of the device structure, which is a pointer to the
5857 * s2io_nic structure.
5858 * @eeprom : pointer to the user level structure provided by ethtool,
5859 * containing all relevant information.
5860 * @data_buf ; user defined value to be written into Eeprom.
5862 * Tries to write the user provided value in the Eeprom, at the offset
5863 * given by the user.
5865 * 0 on success, -EFAULT on failure.
5868 static int s2io_ethtool_seeprom(struct net_device *dev,
5869 struct ethtool_eeprom *eeprom,
5872 int len = eeprom->len, cnt = 0;
5873 u64 valid = 0, data;
5874 struct s2io_nic *sp = dev->priv;
5876 if (eeprom->magic != (sp->pdev->vendor | (sp->pdev->device << 16))) {
5878 "ETHTOOL_WRITE_EEPROM Err: Magic value ");
5879 DBG_PRINT(ERR_DBG, "is wrong, Its not 0x%x\n",
5885 data = (u32) data_buf[cnt] & 0x000000FF;
5887 valid = (u32) (data << 24);
5891 if (write_eeprom(sp, (eeprom->offset + cnt), valid, 0)) {
5893 "ETHTOOL_WRITE_EEPROM Err: Cannot ");
5895 "write into the specified offset\n");
5906 * s2io_register_test - reads and writes into all clock domains.
5907 * @sp : private member of the device structure, which is a pointer to the
5908 * s2io_nic structure.
5909 * @data : variable that returns the result of each of the test conducted b
5912 * Read and write into all clock domains. The NIC has 3 clock domains,
5913 * see that registers in all the three regions are accessible.
5918 static int s2io_register_test(struct s2io_nic * sp, uint64_t * data)
5920 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5921 u64 val64 = 0, exp_val;
5924 val64 = readq(&bar0->pif_rd_swapper_fb);
5925 if (val64 != 0x123456789abcdefULL) {
5927 DBG_PRINT(INFO_DBG, "Read Test level 1 fails\n");
5930 val64 = readq(&bar0->rmac_pause_cfg);
5931 if (val64 != 0xc000ffff00000000ULL) {
5933 DBG_PRINT(INFO_DBG, "Read Test level 2 fails\n");
5936 val64 = readq(&bar0->rx_queue_cfg);
5937 if (sp->device_type == XFRAME_II_DEVICE)
5938 exp_val = 0x0404040404040404ULL;
5940 exp_val = 0x0808080808080808ULL;
5941 if (val64 != exp_val) {
5943 DBG_PRINT(INFO_DBG, "Read Test level 3 fails\n");
5946 val64 = readq(&bar0->xgxs_efifo_cfg);
5947 if (val64 != 0x000000001923141EULL) {
5949 DBG_PRINT(INFO_DBG, "Read Test level 4 fails\n");
5952 val64 = 0x5A5A5A5A5A5A5A5AULL;
5953 writeq(val64, &bar0->xmsi_data);
5954 val64 = readq(&bar0->xmsi_data);
5955 if (val64 != 0x5A5A5A5A5A5A5A5AULL) {
5957 DBG_PRINT(ERR_DBG, "Write Test level 1 fails\n");
5960 val64 = 0xA5A5A5A5A5A5A5A5ULL;
5961 writeq(val64, &bar0->xmsi_data);
5962 val64 = readq(&bar0->xmsi_data);
5963 if (val64 != 0xA5A5A5A5A5A5A5A5ULL) {
5965 DBG_PRINT(ERR_DBG, "Write Test level 2 fails\n");
5973 * s2io_eeprom_test - to verify that EEprom in the xena can be programmed.
5974 * @sp : private member of the device structure, which is a pointer to the
5975 * s2io_nic structure.
5976 * @data:variable that returns the result of each of the test conducted by
5979 * Verify that EEPROM in the xena can be programmed using I2C_CONTROL
5985 static int s2io_eeprom_test(struct s2io_nic * sp, uint64_t * data)
5988 u64 ret_data, org_4F0, org_7F0;
5989 u8 saved_4F0 = 0, saved_7F0 = 0;
5990 struct net_device *dev = sp->dev;
5992 /* Test Write Error at offset 0 */
5993 /* Note that SPI interface allows write access to all areas
5994 * of EEPROM. Hence doing all negative testing only for Xframe I.
5996 if (sp->device_type == XFRAME_I_DEVICE)
5997 if (!write_eeprom(sp, 0, 0, 3))
6000 /* Save current values at offsets 0x4F0 and 0x7F0 */
6001 if (!read_eeprom(sp, 0x4F0, &org_4F0))
6003 if (!read_eeprom(sp, 0x7F0, &org_7F0))
6006 /* Test Write at offset 4f0 */
6007 if (write_eeprom(sp, 0x4F0, 0x012345, 3))
6009 if (read_eeprom(sp, 0x4F0, &ret_data))
6012 if (ret_data != 0x012345) {
6013 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x4F0. "
6014 "Data written %llx Data read %llx\n",
6015 dev->name, (unsigned long long)0x12345,
6016 (unsigned long long)ret_data);
6020 /* Reset the EEPROM data go FFFF */
6021 write_eeprom(sp, 0x4F0, 0xFFFFFF, 3);
6023 /* Test Write Request Error at offset 0x7c */
6024 if (sp->device_type == XFRAME_I_DEVICE)
6025 if (!write_eeprom(sp, 0x07C, 0, 3))
6028 /* Test Write Request at offset 0x7f0 */
6029 if (write_eeprom(sp, 0x7F0, 0x012345, 3))
6031 if (read_eeprom(sp, 0x7F0, &ret_data))
6034 if (ret_data != 0x012345) {
6035 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x7F0. "
6036 "Data written %llx Data read %llx\n",
6037 dev->name, (unsigned long long)0x12345,
6038 (unsigned long long)ret_data);
6042 /* Reset the EEPROM data go FFFF */
6043 write_eeprom(sp, 0x7F0, 0xFFFFFF, 3);
6045 if (sp->device_type == XFRAME_I_DEVICE) {
6046 /* Test Write Error at offset 0x80 */
6047 if (!write_eeprom(sp, 0x080, 0, 3))
6050 /* Test Write Error at offset 0xfc */
6051 if (!write_eeprom(sp, 0x0FC, 0, 3))
6054 /* Test Write Error at offset 0x100 */
6055 if (!write_eeprom(sp, 0x100, 0, 3))
6058 /* Test Write Error at offset 4ec */
6059 if (!write_eeprom(sp, 0x4EC, 0, 3))
6063 /* Restore values at offsets 0x4F0 and 0x7F0 */
6065 write_eeprom(sp, 0x4F0, org_4F0, 3);
6067 write_eeprom(sp, 0x7F0, org_7F0, 3);
6074 * s2io_bist_test - invokes the MemBist test of the card .
6075 * @sp : private member of the device structure, which is a pointer to the
6076 * s2io_nic structure.
6077 * @data:variable that returns the result of each of the test conducted by
6080 * This invokes the MemBist test of the card. We give around
6081 * 2 secs time for the Test to complete. If it's still not complete
6082 * within this peiod, we consider that the test failed.
6084 * 0 on success and -1 on failure.
6087 static int s2io_bist_test(struct s2io_nic * sp, uint64_t * data)
6090 int cnt = 0, ret = -1;
6092 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
6093 bist |= PCI_BIST_START;
6094 pci_write_config_word(sp->pdev, PCI_BIST, bist);
6097 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
6098 if (!(bist & PCI_BIST_START)) {
6099 *data = (bist & PCI_BIST_CODE_MASK);
6111 * s2io-link_test - verifies the link state of the nic
6112 * @sp ; private member of the device structure, which is a pointer to the
6113 * s2io_nic structure.
6114 * @data: variable that returns the result of each of the test conducted by
6117 * The function verifies the link state of the NIC and updates the input
6118 * argument 'data' appropriately.
6123 static int s2io_link_test(struct s2io_nic * sp, uint64_t * data)
6125 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6128 val64 = readq(&bar0->adapter_status);
6129 if(!(LINK_IS_UP(val64)))
6138 * s2io_rldram_test - offline test for access to the RldRam chip on the NIC
6139 * @sp - private member of the device structure, which is a pointer to the
6140 * s2io_nic structure.
6141 * @data - variable that returns the result of each of the test
6142 * conducted by the driver.
6144 * This is one of the offline test that tests the read and write
6145 * access to the RldRam chip on the NIC.
6150 static int s2io_rldram_test(struct s2io_nic * sp, uint64_t * data)
6152 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6154 int cnt, iteration = 0, test_fail = 0;
6156 val64 = readq(&bar0->adapter_control);
6157 val64 &= ~ADAPTER_ECC_EN;
6158 writeq(val64, &bar0->adapter_control);
6160 val64 = readq(&bar0->mc_rldram_test_ctrl);
6161 val64 |= MC_RLDRAM_TEST_MODE;
6162 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6164 val64 = readq(&bar0->mc_rldram_mrs);
6165 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE;
6166 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
6168 val64 |= MC_RLDRAM_MRS_ENABLE;
6169 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
6171 while (iteration < 2) {
6172 val64 = 0x55555555aaaa0000ULL;
6173 if (iteration == 1) {
6174 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6176 writeq(val64, &bar0->mc_rldram_test_d0);
6178 val64 = 0xaaaa5a5555550000ULL;
6179 if (iteration == 1) {
6180 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6182 writeq(val64, &bar0->mc_rldram_test_d1);
6184 val64 = 0x55aaaaaaaa5a0000ULL;
6185 if (iteration == 1) {
6186 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6188 writeq(val64, &bar0->mc_rldram_test_d2);
6190 val64 = (u64) (0x0000003ffffe0100ULL);
6191 writeq(val64, &bar0->mc_rldram_test_add);
6193 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_WRITE |
6195 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6197 for (cnt = 0; cnt < 5; cnt++) {
6198 val64 = readq(&bar0->mc_rldram_test_ctrl);
6199 if (val64 & MC_RLDRAM_TEST_DONE)
6207 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_GO;
6208 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6210 for (cnt = 0; cnt < 5; cnt++) {
6211 val64 = readq(&bar0->mc_rldram_test_ctrl);
6212 if (val64 & MC_RLDRAM_TEST_DONE)
6220 val64 = readq(&bar0->mc_rldram_test_ctrl);
6221 if (!(val64 & MC_RLDRAM_TEST_PASS))
6229 /* Bring the adapter out of test mode */
6230 SPECIAL_REG_WRITE(0, &bar0->mc_rldram_test_ctrl, LF);
6236 * s2io_ethtool_test - conducts 6 tsets to determine the health of card.
6237 * @sp : private member of the device structure, which is a pointer to the
6238 * s2io_nic structure.
6239 * @ethtest : pointer to a ethtool command specific structure that will be
6240 * returned to the user.
6241 * @data : variable that returns the result of each of the test
6242 * conducted by the driver.
6244 * This function conducts 6 tests ( 4 offline and 2 online) to determine
6245 * the health of the card.
6250 static void s2io_ethtool_test(struct net_device *dev,
6251 struct ethtool_test *ethtest,
6254 struct s2io_nic *sp = dev->priv;
6255 int orig_state = netif_running(sp->dev);
6257 if (ethtest->flags == ETH_TEST_FL_OFFLINE) {
6258 /* Offline Tests. */
6260 s2io_close(sp->dev);
6262 if (s2io_register_test(sp, &data[0]))
6263 ethtest->flags |= ETH_TEST_FL_FAILED;
6267 if (s2io_rldram_test(sp, &data[3]))
6268 ethtest->flags |= ETH_TEST_FL_FAILED;
6272 if (s2io_eeprom_test(sp, &data[1]))
6273 ethtest->flags |= ETH_TEST_FL_FAILED;
6275 if (s2io_bist_test(sp, &data[4]))
6276 ethtest->flags |= ETH_TEST_FL_FAILED;
6286 "%s: is not up, cannot run test\n",
6295 if (s2io_link_test(sp, &data[2]))
6296 ethtest->flags |= ETH_TEST_FL_FAILED;
6305 static void s2io_get_ethtool_stats(struct net_device *dev,
6306 struct ethtool_stats *estats,
6310 struct s2io_nic *sp = dev->priv;
6311 struct stat_block *stat_info = sp->mac_control.stats_info;
6313 s2io_updt_stats(sp);
6315 (u64)le32_to_cpu(stat_info->tmac_frms_oflow) << 32 |
6316 le32_to_cpu(stat_info->tmac_frms);
6318 (u64)le32_to_cpu(stat_info->tmac_data_octets_oflow) << 32 |
6319 le32_to_cpu(stat_info->tmac_data_octets);
6320 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms);
6322 (u64)le32_to_cpu(stat_info->tmac_mcst_frms_oflow) << 32 |
6323 le32_to_cpu(stat_info->tmac_mcst_frms);
6325 (u64)le32_to_cpu(stat_info->tmac_bcst_frms_oflow) << 32 |
6326 le32_to_cpu(stat_info->tmac_bcst_frms);
6327 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_pause_ctrl_frms);
6329 (u64)le32_to_cpu(stat_info->tmac_ttl_octets_oflow) << 32 |
6330 le32_to_cpu(stat_info->tmac_ttl_octets);
6332 (u64)le32_to_cpu(stat_info->tmac_ucst_frms_oflow) << 32 |
6333 le32_to_cpu(stat_info->tmac_ucst_frms);
6335 (u64)le32_to_cpu(stat_info->tmac_nucst_frms_oflow) << 32 |
6336 le32_to_cpu(stat_info->tmac_nucst_frms);
6338 (u64)le32_to_cpu(stat_info->tmac_any_err_frms_oflow) << 32 |
6339 le32_to_cpu(stat_info->tmac_any_err_frms);
6340 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_ttl_less_fb_octets);
6341 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_vld_ip_octets);
6343 (u64)le32_to_cpu(stat_info->tmac_vld_ip_oflow) << 32 |
6344 le32_to_cpu(stat_info->tmac_vld_ip);
6346 (u64)le32_to_cpu(stat_info->tmac_drop_ip_oflow) << 32 |
6347 le32_to_cpu(stat_info->tmac_drop_ip);
6349 (u64)le32_to_cpu(stat_info->tmac_icmp_oflow) << 32 |
6350 le32_to_cpu(stat_info->tmac_icmp);
6352 (u64)le32_to_cpu(stat_info->tmac_rst_tcp_oflow) << 32 |
6353 le32_to_cpu(stat_info->tmac_rst_tcp);
6354 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_tcp);
6355 tmp_stats[i++] = (u64)le32_to_cpu(stat_info->tmac_udp_oflow) << 32 |
6356 le32_to_cpu(stat_info->tmac_udp);
6358 (u64)le32_to_cpu(stat_info->rmac_vld_frms_oflow) << 32 |
6359 le32_to_cpu(stat_info->rmac_vld_frms);
6361 (u64)le32_to_cpu(stat_info->rmac_data_octets_oflow) << 32 |
6362 le32_to_cpu(stat_info->rmac_data_octets);
6363 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_fcs_err_frms);
6364 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_drop_frms);
6366 (u64)le32_to_cpu(stat_info->rmac_vld_mcst_frms_oflow) << 32 |
6367 le32_to_cpu(stat_info->rmac_vld_mcst_frms);
6369 (u64)le32_to_cpu(stat_info->rmac_vld_bcst_frms_oflow) << 32 |
6370 le32_to_cpu(stat_info->rmac_vld_bcst_frms);
6371 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_in_rng_len_err_frms);
6372 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_out_rng_len_err_frms);
6373 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_long_frms);
6374 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_pause_ctrl_frms);
6375 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_unsup_ctrl_frms);
6377 (u64)le32_to_cpu(stat_info->rmac_ttl_octets_oflow) << 32 |
6378 le32_to_cpu(stat_info->rmac_ttl_octets);
6380 (u64)le32_to_cpu(stat_info->rmac_accepted_ucst_frms_oflow)
6381 << 32 | le32_to_cpu(stat_info->rmac_accepted_ucst_frms);
6383 (u64)le32_to_cpu(stat_info->rmac_accepted_nucst_frms_oflow)
6384 << 32 | le32_to_cpu(stat_info->rmac_accepted_nucst_frms);
6386 (u64)le32_to_cpu(stat_info->rmac_discarded_frms_oflow) << 32 |
6387 le32_to_cpu(stat_info->rmac_discarded_frms);
6389 (u64)le32_to_cpu(stat_info->rmac_drop_events_oflow)
6390 << 32 | le32_to_cpu(stat_info->rmac_drop_events);
6391 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_less_fb_octets);
6392 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_frms);
6394 (u64)le32_to_cpu(stat_info->rmac_usized_frms_oflow) << 32 |
6395 le32_to_cpu(stat_info->rmac_usized_frms);
6397 (u64)le32_to_cpu(stat_info->rmac_osized_frms_oflow) << 32 |
6398 le32_to_cpu(stat_info->rmac_osized_frms);
6400 (u64)le32_to_cpu(stat_info->rmac_frag_frms_oflow) << 32 |
6401 le32_to_cpu(stat_info->rmac_frag_frms);
6403 (u64)le32_to_cpu(stat_info->rmac_jabber_frms_oflow) << 32 |
6404 le32_to_cpu(stat_info->rmac_jabber_frms);
6405 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_64_frms);
6406 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_65_127_frms);
6407 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_128_255_frms);
6408 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_256_511_frms);
6409 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_512_1023_frms);
6410 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_1024_1518_frms);
6412 (u64)le32_to_cpu(stat_info->rmac_ip_oflow) << 32 |
6413 le32_to_cpu(stat_info->rmac_ip);
6414 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ip_octets);
6415 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_hdr_err_ip);
6417 (u64)le32_to_cpu(stat_info->rmac_drop_ip_oflow) << 32 |
6418 le32_to_cpu(stat_info->rmac_drop_ip);
6420 (u64)le32_to_cpu(stat_info->rmac_icmp_oflow) << 32 |
6421 le32_to_cpu(stat_info->rmac_icmp);
6422 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_tcp);
6424 (u64)le32_to_cpu(stat_info->rmac_udp_oflow) << 32 |
6425 le32_to_cpu(stat_info->rmac_udp);
6427 (u64)le32_to_cpu(stat_info->rmac_err_drp_udp_oflow) << 32 |
6428 le32_to_cpu(stat_info->rmac_err_drp_udp);
6429 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_err_sym);
6430 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q0);
6431 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q1);
6432 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q2);
6433 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q3);
6434 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q4);
6435 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q5);
6436 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q6);
6437 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q7);
6438 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q0);
6439 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q1);
6440 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q2);
6441 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q3);
6442 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q4);
6443 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q5);
6444 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q6);
6445 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q7);
6447 (u64)le32_to_cpu(stat_info->rmac_pause_cnt_oflow) << 32 |
6448 le32_to_cpu(stat_info->rmac_pause_cnt);
6449 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_data_err_cnt);
6450 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_ctrl_err_cnt);
6452 (u64)le32_to_cpu(stat_info->rmac_accepted_ip_oflow) << 32 |
6453 le32_to_cpu(stat_info->rmac_accepted_ip);
6454 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp);
6455 tmp_stats[i++] = le32_to_cpu(stat_info->rd_req_cnt);
6456 tmp_stats[i++] = le32_to_cpu(stat_info->new_rd_req_cnt);
6457 tmp_stats[i++] = le32_to_cpu(stat_info->new_rd_req_rtry_cnt);
6458 tmp_stats[i++] = le32_to_cpu(stat_info->rd_rtry_cnt);
6459 tmp_stats[i++] = le32_to_cpu(stat_info->wr_rtry_rd_ack_cnt);
6460 tmp_stats[i++] = le32_to_cpu(stat_info->wr_req_cnt);
6461 tmp_stats[i++] = le32_to_cpu(stat_info->new_wr_req_cnt);
6462 tmp_stats[i++] = le32_to_cpu(stat_info->new_wr_req_rtry_cnt);
6463 tmp_stats[i++] = le32_to_cpu(stat_info->wr_rtry_cnt);
6464 tmp_stats[i++] = le32_to_cpu(stat_info->wr_disc_cnt);
6465 tmp_stats[i++] = le32_to_cpu(stat_info->rd_rtry_wr_ack_cnt);
6466 tmp_stats[i++] = le32_to_cpu(stat_info->txp_wr_cnt);
6467 tmp_stats[i++] = le32_to_cpu(stat_info->txd_rd_cnt);
6468 tmp_stats[i++] = le32_to_cpu(stat_info->txd_wr_cnt);
6469 tmp_stats[i++] = le32_to_cpu(stat_info->rxd_rd_cnt);
6470 tmp_stats[i++] = le32_to_cpu(stat_info->rxd_wr_cnt);
6471 tmp_stats[i++] = le32_to_cpu(stat_info->txf_rd_cnt);
6472 tmp_stats[i++] = le32_to_cpu(stat_info->rxf_wr_cnt);
6474 /* Enhanced statistics exist only for Hercules */
6475 if(sp->device_type == XFRAME_II_DEVICE) {
6477 le64_to_cpu(stat_info->rmac_ttl_1519_4095_frms);
6479 le64_to_cpu(stat_info->rmac_ttl_4096_8191_frms);
6481 le64_to_cpu(stat_info->rmac_ttl_8192_max_frms);
6482 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_gt_max_frms);
6483 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_osized_alt_frms);
6484 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_jabber_alt_frms);
6485 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_gt_max_alt_frms);
6486 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_vlan_frms);
6487 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_len_discard);
6488 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_fcs_discard);
6489 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pf_discard);
6490 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_da_discard);
6491 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_red_discard);
6492 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_rts_discard);
6493 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_ingm_full_discard);
6494 tmp_stats[i++] = le32_to_cpu(stat_info->link_fault_cnt);
6498 tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs;
6499 tmp_stats[i++] = stat_info->sw_stat.double_ecc_errs;
6500 tmp_stats[i++] = stat_info->sw_stat.parity_err_cnt;
6501 tmp_stats[i++] = stat_info->sw_stat.serious_err_cnt;
6502 tmp_stats[i++] = stat_info->sw_stat.soft_reset_cnt;
6503 tmp_stats[i++] = stat_info->sw_stat.fifo_full_cnt;
6504 for (k = 0; k < MAX_RX_RINGS; k++)
6505 tmp_stats[i++] = stat_info->sw_stat.ring_full_cnt[k];
6506 tmp_stats[i++] = stat_info->xpak_stat.alarm_transceiver_temp_high;
6507 tmp_stats[i++] = stat_info->xpak_stat.alarm_transceiver_temp_low;
6508 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_bias_current_high;
6509 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_bias_current_low;
6510 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_output_power_high;
6511 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_output_power_low;
6512 tmp_stats[i++] = stat_info->xpak_stat.warn_transceiver_temp_high;
6513 tmp_stats[i++] = stat_info->xpak_stat.warn_transceiver_temp_low;
6514 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_bias_current_high;
6515 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_bias_current_low;
6516 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_output_power_high;
6517 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_output_power_low;
6518 tmp_stats[i++] = stat_info->sw_stat.clubbed_frms_cnt;
6519 tmp_stats[i++] = stat_info->sw_stat.sending_both;
6520 tmp_stats[i++] = stat_info->sw_stat.outof_sequence_pkts;
6521 tmp_stats[i++] = stat_info->sw_stat.flush_max_pkts;
6522 if (stat_info->sw_stat.num_aggregations) {
6523 u64 tmp = stat_info->sw_stat.sum_avg_pkts_aggregated;
6526 * Since 64-bit divide does not work on all platforms,
6527 * do repeated subtraction.
6529 while (tmp >= stat_info->sw_stat.num_aggregations) {
6530 tmp -= stat_info->sw_stat.num_aggregations;
6533 tmp_stats[i++] = count;
6537 tmp_stats[i++] = stat_info->sw_stat.mem_alloc_fail_cnt;
6538 tmp_stats[i++] = stat_info->sw_stat.pci_map_fail_cnt;
6539 tmp_stats[i++] = stat_info->sw_stat.watchdog_timer_cnt;
6540 tmp_stats[i++] = stat_info->sw_stat.mem_allocated;
6541 tmp_stats[i++] = stat_info->sw_stat.mem_freed;
6542 tmp_stats[i++] = stat_info->sw_stat.link_up_cnt;
6543 tmp_stats[i++] = stat_info->sw_stat.link_down_cnt;
6544 tmp_stats[i++] = stat_info->sw_stat.link_up_time;
6545 tmp_stats[i++] = stat_info->sw_stat.link_down_time;
6547 tmp_stats[i++] = stat_info->sw_stat.tx_buf_abort_cnt;
6548 tmp_stats[i++] = stat_info->sw_stat.tx_desc_abort_cnt;
6549 tmp_stats[i++] = stat_info->sw_stat.tx_parity_err_cnt;
6550 tmp_stats[i++] = stat_info->sw_stat.tx_link_loss_cnt;
6551 tmp_stats[i++] = stat_info->sw_stat.tx_list_proc_err_cnt;
6553 tmp_stats[i++] = stat_info->sw_stat.rx_parity_err_cnt;
6554 tmp_stats[i++] = stat_info->sw_stat.rx_abort_cnt;
6555 tmp_stats[i++] = stat_info->sw_stat.rx_parity_abort_cnt;
6556 tmp_stats[i++] = stat_info->sw_stat.rx_rda_fail_cnt;
6557 tmp_stats[i++] = stat_info->sw_stat.rx_unkn_prot_cnt;
6558 tmp_stats[i++] = stat_info->sw_stat.rx_fcs_err_cnt;
6559 tmp_stats[i++] = stat_info->sw_stat.rx_buf_size_err_cnt;
6560 tmp_stats[i++] = stat_info->sw_stat.rx_rxd_corrupt_cnt;
6561 tmp_stats[i++] = stat_info->sw_stat.rx_unkn_err_cnt;
6562 tmp_stats[i++] = stat_info->sw_stat.tda_err_cnt;
6563 tmp_stats[i++] = stat_info->sw_stat.pfc_err_cnt;
6564 tmp_stats[i++] = stat_info->sw_stat.pcc_err_cnt;
6565 tmp_stats[i++] = stat_info->sw_stat.tti_err_cnt;
6566 tmp_stats[i++] = stat_info->sw_stat.tpa_err_cnt;
6567 tmp_stats[i++] = stat_info->sw_stat.sm_err_cnt;
6568 tmp_stats[i++] = stat_info->sw_stat.lso_err_cnt;
6569 tmp_stats[i++] = stat_info->sw_stat.mac_tmac_err_cnt;
6570 tmp_stats[i++] = stat_info->sw_stat.mac_rmac_err_cnt;
6571 tmp_stats[i++] = stat_info->sw_stat.xgxs_txgxs_err_cnt;
6572 tmp_stats[i++] = stat_info->sw_stat.xgxs_rxgxs_err_cnt;
6573 tmp_stats[i++] = stat_info->sw_stat.rc_err_cnt;
6574 tmp_stats[i++] = stat_info->sw_stat.prc_pcix_err_cnt;
6575 tmp_stats[i++] = stat_info->sw_stat.rpa_err_cnt;
6576 tmp_stats[i++] = stat_info->sw_stat.rda_err_cnt;
6577 tmp_stats[i++] = stat_info->sw_stat.rti_err_cnt;
6578 tmp_stats[i++] = stat_info->sw_stat.mc_err_cnt;
6581 static int s2io_ethtool_get_regs_len(struct net_device *dev)
6583 return (XENA_REG_SPACE);
6587 static u32 s2io_ethtool_get_rx_csum(struct net_device * dev)
6589 struct s2io_nic *sp = dev->priv;
6591 return (sp->rx_csum);
6594 static int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data)
6596 struct s2io_nic *sp = dev->priv;
6606 static int s2io_get_eeprom_len(struct net_device *dev)
6608 return (XENA_EEPROM_SPACE);
6611 static int s2io_get_sset_count(struct net_device *dev, int sset)
6613 struct s2io_nic *sp = dev->priv;
6617 return S2IO_TEST_LEN;
6619 switch(sp->device_type) {
6620 case XFRAME_I_DEVICE:
6621 return XFRAME_I_STAT_LEN;
6622 case XFRAME_II_DEVICE:
6623 return XFRAME_II_STAT_LEN;
6632 static void s2io_ethtool_get_strings(struct net_device *dev,
6633 u32 stringset, u8 * data)
6636 struct s2io_nic *sp = dev->priv;
6638 switch (stringset) {
6640 memcpy(data, s2io_gstrings, S2IO_STRINGS_LEN);
6643 stat_size = sizeof(ethtool_xena_stats_keys);
6644 memcpy(data, ðtool_xena_stats_keys,stat_size);
6645 if(sp->device_type == XFRAME_II_DEVICE) {
6646 memcpy(data + stat_size,
6647 ðtool_enhanced_stats_keys,
6648 sizeof(ethtool_enhanced_stats_keys));
6649 stat_size += sizeof(ethtool_enhanced_stats_keys);
6652 memcpy(data + stat_size, ðtool_driver_stats_keys,
6653 sizeof(ethtool_driver_stats_keys));
6657 static int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data)
6660 dev->features |= NETIF_F_IP_CSUM;
6662 dev->features &= ~NETIF_F_IP_CSUM;
6667 static u32 s2io_ethtool_op_get_tso(struct net_device *dev)
6669 return (dev->features & NETIF_F_TSO) != 0;
6671 static int s2io_ethtool_op_set_tso(struct net_device *dev, u32 data)
6674 dev->features |= (NETIF_F_TSO | NETIF_F_TSO6);
6676 dev->features &= ~(NETIF_F_TSO | NETIF_F_TSO6);
6681 static const struct ethtool_ops netdev_ethtool_ops = {
6682 .get_settings = s2io_ethtool_gset,
6683 .set_settings = s2io_ethtool_sset,
6684 .get_drvinfo = s2io_ethtool_gdrvinfo,
6685 .get_regs_len = s2io_ethtool_get_regs_len,
6686 .get_regs = s2io_ethtool_gregs,
6687 .get_link = ethtool_op_get_link,
6688 .get_eeprom_len = s2io_get_eeprom_len,
6689 .get_eeprom = s2io_ethtool_geeprom,
6690 .set_eeprom = s2io_ethtool_seeprom,
6691 .get_ringparam = s2io_ethtool_gringparam,
6692 .get_pauseparam = s2io_ethtool_getpause_data,
6693 .set_pauseparam = s2io_ethtool_setpause_data,
6694 .get_rx_csum = s2io_ethtool_get_rx_csum,
6695 .set_rx_csum = s2io_ethtool_set_rx_csum,
6696 .set_tx_csum = s2io_ethtool_op_set_tx_csum,
6697 .set_sg = ethtool_op_set_sg,
6698 .get_tso = s2io_ethtool_op_get_tso,
6699 .set_tso = s2io_ethtool_op_set_tso,
6700 .set_ufo = ethtool_op_set_ufo,
6701 .self_test = s2io_ethtool_test,
6702 .get_strings = s2io_ethtool_get_strings,
6703 .phys_id = s2io_ethtool_idnic,
6704 .get_ethtool_stats = s2io_get_ethtool_stats,
6705 .get_sset_count = s2io_get_sset_count,
6709 * s2io_ioctl - Entry point for the Ioctl
6710 * @dev : Device pointer.
6711 * @ifr : An IOCTL specefic structure, that can contain a pointer to
6712 * a proprietary structure used to pass information to the driver.
6713 * @cmd : This is used to distinguish between the different commands that
6714 * can be passed to the IOCTL functions.
6716 * Currently there are no special functionality supported in IOCTL, hence
6717 * function always return EOPNOTSUPPORTED
6720 static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
6726 * s2io_change_mtu - entry point to change MTU size for the device.
6727 * @dev : device pointer.
6728 * @new_mtu : the new MTU size for the device.
6729 * Description: A driver entry point to change MTU size for the device.
6730 * Before changing the MTU the device must be stopped.
6732 * 0 on success and an appropriate (-)ve integer as defined in errno.h
6736 static int s2io_change_mtu(struct net_device *dev, int new_mtu)
6738 struct s2io_nic *sp = dev->priv;
6741 if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) {
6742 DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n",
6748 if (netif_running(dev)) {
6749 s2io_stop_all_tx_queue(sp);
6751 ret = s2io_card_up(sp);
6753 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
6757 s2io_wake_all_tx_queue(sp);
6758 } else { /* Device is down */
6759 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6760 u64 val64 = new_mtu;
6762 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
6769 * s2io_tasklet - Bottom half of the ISR.
6770 * @dev_adr : address of the device structure in dma_addr_t format.
6772 * This is the tasklet or the bottom half of the ISR. This is
6773 * an extension of the ISR which is scheduled by the scheduler to be run
6774 * when the load on the CPU is low. All low priority tasks of the ISR can
6775 * be pushed into the tasklet. For now the tasklet is used only to
6776 * replenish the Rx buffers in the Rx buffer descriptors.
6781 static void s2io_tasklet(unsigned long dev_addr)
6783 struct net_device *dev = (struct net_device *) dev_addr;
6784 struct s2io_nic *sp = dev->priv;
6786 struct mac_info *mac_control;
6787 struct config_param *config;
6789 mac_control = &sp->mac_control;
6790 config = &sp->config;
6792 if (!TASKLET_IN_USE) {
6793 for (i = 0; i < config->rx_ring_num; i++) {
6794 ret = fill_rx_buffers(sp, i);
6795 if (ret == -ENOMEM) {
6796 DBG_PRINT(INFO_DBG, "%s: Out of ",
6798 DBG_PRINT(INFO_DBG, "memory in tasklet\n");
6800 } else if (ret == -EFILL) {
6802 "%s: Rx Ring %d is full\n",
6807 clear_bit(0, (&sp->tasklet_status));
6812 * s2io_set_link - Set the LInk status
6813 * @data: long pointer to device private structue
6814 * Description: Sets the link status for the adapter
6817 static void s2io_set_link(struct work_struct *work)
6819 struct s2io_nic *nic = container_of(work, struct s2io_nic, set_link_task);
6820 struct net_device *dev = nic->dev;
6821 struct XENA_dev_config __iomem *bar0 = nic->bar0;
6827 if (!netif_running(dev))
6830 if (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(nic->state))) {
6831 /* The card is being reset, no point doing anything */
6835 subid = nic->pdev->subsystem_device;
6836 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
6838 * Allow a small delay for the NICs self initiated
6839 * cleanup to complete.
6844 val64 = readq(&bar0->adapter_status);
6845 if (LINK_IS_UP(val64)) {
6846 if (!(readq(&bar0->adapter_control) & ADAPTER_CNTL_EN)) {
6847 if (verify_xena_quiescence(nic)) {
6848 val64 = readq(&bar0->adapter_control);
6849 val64 |= ADAPTER_CNTL_EN;
6850 writeq(val64, &bar0->adapter_control);
6851 if (CARDS_WITH_FAULTY_LINK_INDICATORS(
6852 nic->device_type, subid)) {
6853 val64 = readq(&bar0->gpio_control);
6854 val64 |= GPIO_CTRL_GPIO_0;
6855 writeq(val64, &bar0->gpio_control);
6856 val64 = readq(&bar0->gpio_control);
6858 val64 |= ADAPTER_LED_ON;
6859 writeq(val64, &bar0->adapter_control);
6861 nic->device_enabled_once = TRUE;
6863 DBG_PRINT(ERR_DBG, "%s: Error: ", dev->name);
6864 DBG_PRINT(ERR_DBG, "device is not Quiescent\n");
6865 s2io_stop_all_tx_queue(nic);
6868 val64 = readq(&bar0->adapter_control);
6869 val64 |= ADAPTER_LED_ON;
6870 writeq(val64, &bar0->adapter_control);
6871 s2io_link(nic, LINK_UP);
6873 if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
6875 val64 = readq(&bar0->gpio_control);
6876 val64 &= ~GPIO_CTRL_GPIO_0;
6877 writeq(val64, &bar0->gpio_control);
6878 val64 = readq(&bar0->gpio_control);
6881 val64 = readq(&bar0->adapter_control);
6882 val64 = val64 &(~ADAPTER_LED_ON);
6883 writeq(val64, &bar0->adapter_control);
6884 s2io_link(nic, LINK_DOWN);
6886 clear_bit(__S2IO_STATE_LINK_TASK, &(nic->state));
6892 static int set_rxd_buffer_pointer(struct s2io_nic *sp, struct RxD_t *rxdp,
6894 struct sk_buff **skb, u64 *temp0, u64 *temp1,
6895 u64 *temp2, int size)
6897 struct net_device *dev = sp->dev;
6898 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
6900 if ((sp->rxd_mode == RXD_MODE_1) && (rxdp->Host_Control == 0)) {
6901 struct RxD1 *rxdp1 = (struct RxD1 *)rxdp;
6904 DBG_PRINT(INFO_DBG, "SKB is not NULL\n");
6906 * As Rx frame are not going to be processed,
6907 * using same mapped address for the Rxd
6910 rxdp1->Buffer0_ptr = *temp0;
6912 *skb = dev_alloc_skb(size);
6914 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
6915 DBG_PRINT(INFO_DBG, "memory to allocate ");
6916 DBG_PRINT(INFO_DBG, "1 buf mode SKBs\n");
6917 sp->mac_control.stats_info->sw_stat. \
6918 mem_alloc_fail_cnt++;
6921 sp->mac_control.stats_info->sw_stat.mem_allocated
6922 += (*skb)->truesize;
6923 /* storing the mapped addr in a temp variable
6924 * such it will be used for next rxd whose
6925 * Host Control is NULL
6927 rxdp1->Buffer0_ptr = *temp0 =
6928 pci_map_single( sp->pdev, (*skb)->data,
6929 size - NET_IP_ALIGN,
6930 PCI_DMA_FROMDEVICE);
6931 if( (rxdp1->Buffer0_ptr == 0) ||
6932 (rxdp1->Buffer0_ptr == DMA_ERROR_CODE)) {
6933 goto memalloc_failed;
6935 rxdp->Host_Control = (unsigned long) (*skb);
6937 } else if ((sp->rxd_mode == RXD_MODE_3B) && (rxdp->Host_Control == 0)) {
6938 struct RxD3 *rxdp3 = (struct RxD3 *)rxdp;
6939 /* Two buffer Mode */
6941 rxdp3->Buffer2_ptr = *temp2;
6942 rxdp3->Buffer0_ptr = *temp0;
6943 rxdp3->Buffer1_ptr = *temp1;
6945 *skb = dev_alloc_skb(size);
6947 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
6948 DBG_PRINT(INFO_DBG, "memory to allocate ");
6949 DBG_PRINT(INFO_DBG, "2 buf mode SKBs\n");
6950 sp->mac_control.stats_info->sw_stat. \
6951 mem_alloc_fail_cnt++;
6954 sp->mac_control.stats_info->sw_stat.mem_allocated
6955 += (*skb)->truesize;
6956 rxdp3->Buffer2_ptr = *temp2 =
6957 pci_map_single(sp->pdev, (*skb)->data,
6959 PCI_DMA_FROMDEVICE);
6960 if( (rxdp3->Buffer2_ptr == 0) ||
6961 (rxdp3->Buffer2_ptr == DMA_ERROR_CODE)) {
6962 goto memalloc_failed;
6964 rxdp3->Buffer0_ptr = *temp0 =
6965 pci_map_single( sp->pdev, ba->ba_0, BUF0_LEN,
6966 PCI_DMA_FROMDEVICE);
6967 if( (rxdp3->Buffer0_ptr == 0) ||
6968 (rxdp3->Buffer0_ptr == DMA_ERROR_CODE)) {
6969 pci_unmap_single (sp->pdev,
6970 (dma_addr_t)rxdp3->Buffer2_ptr,
6971 dev->mtu + 4, PCI_DMA_FROMDEVICE);
6972 goto memalloc_failed;
6974 rxdp->Host_Control = (unsigned long) (*skb);
6976 /* Buffer-1 will be dummy buffer not used */
6977 rxdp3->Buffer1_ptr = *temp1 =
6978 pci_map_single(sp->pdev, ba->ba_1, BUF1_LEN,
6979 PCI_DMA_FROMDEVICE);
6980 if( (rxdp3->Buffer1_ptr == 0) ||
6981 (rxdp3->Buffer1_ptr == DMA_ERROR_CODE)) {
6982 pci_unmap_single (sp->pdev,
6983 (dma_addr_t)rxdp3->Buffer0_ptr,
6984 BUF0_LEN, PCI_DMA_FROMDEVICE);
6985 pci_unmap_single (sp->pdev,
6986 (dma_addr_t)rxdp3->Buffer2_ptr,
6987 dev->mtu + 4, PCI_DMA_FROMDEVICE);
6988 goto memalloc_failed;
6994 stats->pci_map_fail_cnt++;
6995 stats->mem_freed += (*skb)->truesize;
6996 dev_kfree_skb(*skb);
7000 static void set_rxd_buffer_size(struct s2io_nic *sp, struct RxD_t *rxdp,
7003 struct net_device *dev = sp->dev;
7004 if (sp->rxd_mode == RXD_MODE_1) {
7005 rxdp->Control_2 = SET_BUFFER0_SIZE_1( size - NET_IP_ALIGN);
7006 } else if (sp->rxd_mode == RXD_MODE_3B) {
7007 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
7008 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
7009 rxdp->Control_2 |= SET_BUFFER2_SIZE_3( dev->mtu + 4);
7013 static int rxd_owner_bit_reset(struct s2io_nic *sp)
7015 int i, j, k, blk_cnt = 0, size;
7016 struct mac_info * mac_control = &sp->mac_control;
7017 struct config_param *config = &sp->config;
7018 struct net_device *dev = sp->dev;
7019 struct RxD_t *rxdp = NULL;
7020 struct sk_buff *skb = NULL;
7021 struct buffAdd *ba = NULL;
7022 u64 temp0_64 = 0, temp1_64 = 0, temp2_64 = 0;
7024 /* Calculate the size based on ring mode */
7025 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
7026 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
7027 if (sp->rxd_mode == RXD_MODE_1)
7028 size += NET_IP_ALIGN;
7029 else if (sp->rxd_mode == RXD_MODE_3B)
7030 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
7032 for (i = 0; i < config->rx_ring_num; i++) {
7033 blk_cnt = config->rx_cfg[i].num_rxd /
7034 (rxd_count[sp->rxd_mode] +1);
7036 for (j = 0; j < blk_cnt; j++) {
7037 for (k = 0; k < rxd_count[sp->rxd_mode]; k++) {
7038 rxdp = mac_control->rings[i].
7039 rx_blocks[j].rxds[k].virt_addr;
7040 if(sp->rxd_mode == RXD_MODE_3B)
7041 ba = &mac_control->rings[i].ba[j][k];
7042 if (set_rxd_buffer_pointer(sp, rxdp, ba,
7043 &skb,(u64 *)&temp0_64,
7050 set_rxd_buffer_size(sp, rxdp, size);
7052 /* flip the Ownership bit to Hardware */
7053 rxdp->Control_1 |= RXD_OWN_XENA;
7061 static int s2io_add_isr(struct s2io_nic * sp)
7064 struct net_device *dev = sp->dev;
7067 if (sp->config.intr_type == MSI_X)
7068 ret = s2io_enable_msi_x(sp);
7070 DBG_PRINT(ERR_DBG, "%s: Defaulting to INTA\n", dev->name);
7071 sp->config.intr_type = INTA;
7074 /* Store the values of the MSIX table in the struct s2io_nic structure */
7075 store_xmsi_data(sp);
7077 /* After proper initialization of H/W, register ISR */
7078 if (sp->config.intr_type == MSI_X) {
7079 int i, msix_tx_cnt=0,msix_rx_cnt=0;
7081 for (i=1; (sp->s2io_entries[i].in_use == MSIX_FLG); i++) {
7082 if (sp->s2io_entries[i].type == MSIX_FIFO_TYPE) {
7083 sprintf(sp->desc[i], "%s:MSI-X-%d-TX",
7085 err = request_irq(sp->entries[i].vector,
7086 s2io_msix_fifo_handle, 0, sp->desc[i],
7087 sp->s2io_entries[i].arg);
7088 /* If either data or addr is zero print it */
7089 if(!(sp->msix_info[i].addr &&
7090 sp->msix_info[i].data)) {
7091 DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx "
7092 "Data:0x%lx\n",sp->desc[i],
7093 (unsigned long long)
7094 sp->msix_info[i].addr,
7096 ntohl(sp->msix_info[i].data));
7101 sprintf(sp->desc[i], "%s:MSI-X-%d-RX",
7103 err = request_irq(sp->entries[i].vector,
7104 s2io_msix_ring_handle, 0, sp->desc[i],
7105 sp->s2io_entries[i].arg);
7106 /* If either data or addr is zero print it */
7107 if(!(sp->msix_info[i].addr &&
7108 sp->msix_info[i].data)) {
7109 DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx "
7110 "Data:0x%lx\n",sp->desc[i],
7111 (unsigned long long)
7112 sp->msix_info[i].addr,
7114 ntohl(sp->msix_info[i].data));
7120 remove_msix_isr(sp);
7121 DBG_PRINT(ERR_DBG,"%s:MSI-X-%d registration "
7122 "failed\n", dev->name, i);
7123 DBG_PRINT(ERR_DBG, "%s: defaulting to INTA\n",
7125 sp->config.intr_type = INTA;
7128 sp->s2io_entries[i].in_use = MSIX_REGISTERED_SUCCESS;
7131 printk(KERN_INFO "MSI-X-TX %d entries enabled\n",
7133 printk(KERN_INFO "MSI-X-RX %d entries enabled\n",
7137 if (sp->config.intr_type == INTA) {
7138 err = request_irq((int) sp->pdev->irq, s2io_isr, IRQF_SHARED,
7141 DBG_PRINT(ERR_DBG, "%s: ISR registration failed\n",
7148 static void s2io_rem_isr(struct s2io_nic * sp)
7150 if (sp->config.intr_type == MSI_X)
7151 remove_msix_isr(sp);
7153 remove_inta_isr(sp);
7156 static void do_s2io_card_down(struct s2io_nic * sp, int do_io)
7159 struct XENA_dev_config __iomem *bar0 = sp->bar0;
7160 unsigned long flags;
7161 register u64 val64 = 0;
7162 struct config_param *config;
7163 config = &sp->config;
7165 if (!is_s2io_card_up(sp))
7168 del_timer_sync(&sp->alarm_timer);
7169 /* If s2io_set_link task is executing, wait till it completes. */
7170 while (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(sp->state))) {
7173 clear_bit(__S2IO_STATE_CARD_UP, &sp->state);
7177 napi_disable(&sp->napi);
7179 /* disable Tx and Rx traffic on the NIC */
7186 tasklet_kill(&sp->task);
7188 /* Check if the device is Quiescent and then Reset the NIC */
7190 /* As per the HW requirement we need to replenish the
7191 * receive buffer to avoid the ring bump. Since there is
7192 * no intention of processing the Rx frame at this pointwe are
7193 * just settting the ownership bit of rxd in Each Rx
7194 * ring to HW and set the appropriate buffer size
7195 * based on the ring mode
7197 rxd_owner_bit_reset(sp);
7199 val64 = readq(&bar0->adapter_status);
7200 if (verify_xena_quiescence(sp)) {
7201 if(verify_pcc_quiescent(sp, sp->device_enabled_once))
7209 "s2io_close:Device not Quiescent ");
7210 DBG_PRINT(ERR_DBG, "adaper status reads 0x%llx\n",
7211 (unsigned long long) val64);
7218 /* Free all Tx buffers */
7219 free_tx_buffers(sp);
7221 /* Free all Rx buffers */
7222 spin_lock_irqsave(&sp->rx_lock, flags);
7223 free_rx_buffers(sp);
7224 spin_unlock_irqrestore(&sp->rx_lock, flags);
7226 clear_bit(__S2IO_STATE_LINK_TASK, &(sp->state));
7229 static void s2io_card_down(struct s2io_nic * sp)
7231 do_s2io_card_down(sp, 1);
7234 static int s2io_card_up(struct s2io_nic * sp)
7237 struct mac_info *mac_control;
7238 struct config_param *config;
7239 struct net_device *dev = (struct net_device *) sp->dev;
7242 /* Initialize the H/W I/O registers */
7245 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
7253 * Initializing the Rx buffers. For now we are considering only 1
7254 * Rx ring and initializing buffers into 30 Rx blocks
7256 mac_control = &sp->mac_control;
7257 config = &sp->config;
7259 for (i = 0; i < config->rx_ring_num; i++) {
7260 if ((ret = fill_rx_buffers(sp, i))) {
7261 DBG_PRINT(ERR_DBG, "%s: Out of memory in Open\n",
7264 free_rx_buffers(sp);
7267 DBG_PRINT(INFO_DBG, "Buf in ring:%d is %d:\n", i,
7268 atomic_read(&sp->rx_bufs_left[i]));
7271 /* Initialise napi */
7273 napi_enable(&sp->napi);
7275 /* Maintain the state prior to the open */
7276 if (sp->promisc_flg)
7277 sp->promisc_flg = 0;
7278 if (sp->m_cast_flg) {
7280 sp->all_multi_pos= 0;
7283 /* Setting its receive mode */
7284 s2io_set_multicast(dev);
7287 /* Initialize max aggregatable pkts per session based on MTU */
7288 sp->lro_max_aggr_per_sess = ((1<<16) - 1) / dev->mtu;
7289 /* Check if we can use(if specified) user provided value */
7290 if (lro_max_pkts < sp->lro_max_aggr_per_sess)
7291 sp->lro_max_aggr_per_sess = lro_max_pkts;
7294 /* Enable Rx Traffic and interrupts on the NIC */
7295 if (start_nic(sp)) {
7296 DBG_PRINT(ERR_DBG, "%s: Starting NIC failed\n", dev->name);
7298 free_rx_buffers(sp);
7302 /* Add interrupt service routine */
7303 if (s2io_add_isr(sp) != 0) {
7304 if (sp->config.intr_type == MSI_X)
7307 free_rx_buffers(sp);
7311 S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2));
7313 /* Enable tasklet for the device */
7314 tasklet_init(&sp->task, s2io_tasklet, (unsigned long) dev);
7316 /* Enable select interrupts */
7317 en_dis_err_alarms(sp, ENA_ALL_INTRS, ENABLE_INTRS);
7318 if (sp->config.intr_type != INTA)
7319 en_dis_able_nic_intrs(sp, ENA_ALL_INTRS, DISABLE_INTRS);
7321 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
7322 interruptible |= TX_PIC_INTR;
7323 en_dis_able_nic_intrs(sp, interruptible, ENABLE_INTRS);
7326 set_bit(__S2IO_STATE_CARD_UP, &sp->state);
7331 * s2io_restart_nic - Resets the NIC.
7332 * @data : long pointer to the device private structure
7334 * This function is scheduled to be run by the s2io_tx_watchdog
7335 * function after 0.5 secs to reset the NIC. The idea is to reduce
7336 * the run time of the watch dog routine which is run holding a
7340 static void s2io_restart_nic(struct work_struct *work)
7342 struct s2io_nic *sp = container_of(work, struct s2io_nic, rst_timer_task);
7343 struct net_device *dev = sp->dev;
7347 if (!netif_running(dev))
7351 if (s2io_card_up(sp)) {
7352 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
7355 s2io_wake_all_tx_queue(sp);
7356 DBG_PRINT(ERR_DBG, "%s: was reset by Tx watchdog timer\n",
7363 * s2io_tx_watchdog - Watchdog for transmit side.
7364 * @dev : Pointer to net device structure
7366 * This function is triggered if the Tx Queue is stopped
7367 * for a pre-defined amount of time when the Interface is still up.
7368 * If the Interface is jammed in such a situation, the hardware is
7369 * reset (by s2io_close) and restarted again (by s2io_open) to
7370 * overcome any problem that might have been caused in the hardware.
7375 static void s2io_tx_watchdog(struct net_device *dev)
7377 struct s2io_nic *sp = dev->priv;
7379 if (netif_carrier_ok(dev)) {
7380 sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt++;
7381 schedule_work(&sp->rst_timer_task);
7382 sp->mac_control.stats_info->sw_stat.soft_reset_cnt++;
7387 * rx_osm_handler - To perform some OS related operations on SKB.
7388 * @sp: private member of the device structure,pointer to s2io_nic structure.
7389 * @skb : the socket buffer pointer.
7390 * @len : length of the packet
7391 * @cksum : FCS checksum of the frame.
7392 * @ring_no : the ring from which this RxD was extracted.
7394 * This function is called by the Rx interrupt serivce routine to perform
7395 * some OS related operations on the SKB before passing it to the upper
7396 * layers. It mainly checks if the checksum is OK, if so adds it to the
7397 * SKBs cksum variable, increments the Rx packet count and passes the SKB
7398 * to the upper layer. If the checksum is wrong, it increments the Rx
7399 * packet error count, frees the SKB and returns error.
7401 * SUCCESS on success and -1 on failure.
7403 static int rx_osm_handler(struct ring_info *ring_data, struct RxD_t * rxdp)
7405 struct s2io_nic *sp = ring_data->nic;
7406 struct net_device *dev = (struct net_device *) sp->dev;
7407 struct sk_buff *skb = (struct sk_buff *)
7408 ((unsigned long) rxdp->Host_Control);
7409 int ring_no = ring_data->ring_no;
7410 u16 l3_csum, l4_csum;
7411 unsigned long long err = rxdp->Control_1 & RXD_T_CODE;
7418 /* Check for parity error */
7420 sp->mac_control.stats_info->sw_stat.parity_err_cnt++;
7422 err_mask = err >> 48;
7425 sp->mac_control.stats_info->sw_stat.
7426 rx_parity_err_cnt++;
7430 sp->mac_control.stats_info->sw_stat.
7435 sp->mac_control.stats_info->sw_stat.
7436 rx_parity_abort_cnt++;
7440 sp->mac_control.stats_info->sw_stat.
7445 sp->mac_control.stats_info->sw_stat.
7450 sp->mac_control.stats_info->sw_stat.
7455 sp->mac_control.stats_info->sw_stat.
7456 rx_buf_size_err_cnt++;
7460 sp->mac_control.stats_info->sw_stat.
7461 rx_rxd_corrupt_cnt++;
7465 sp->mac_control.stats_info->sw_stat.
7470 * Drop the packet if bad transfer code. Exception being
7471 * 0x5, which could be due to unsupported IPv6 extension header.
7472 * In this case, we let stack handle the packet.
7473 * Note that in this case, since checksum will be incorrect,
7474 * stack will validate the same.
7476 if (err_mask != 0x5) {
7477 DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%x\n",
7478 dev->name, err_mask);
7479 sp->stats.rx_crc_errors++;
7480 sp->mac_control.stats_info->sw_stat.mem_freed
7483 atomic_dec(&sp->rx_bufs_left[ring_no]);
7484 rxdp->Host_Control = 0;
7489 /* Updating statistics */
7490 sp->stats.rx_packets++;
7491 rxdp->Host_Control = 0;
7492 if (sp->rxd_mode == RXD_MODE_1) {
7493 int len = RXD_GET_BUFFER0_SIZE_1(rxdp->Control_2);
7495 sp->stats.rx_bytes += len;
7498 } else if (sp->rxd_mode == RXD_MODE_3B) {
7499 int get_block = ring_data->rx_curr_get_info.block_index;
7500 int get_off = ring_data->rx_curr_get_info.offset;
7501 int buf0_len = RXD_GET_BUFFER0_SIZE_3(rxdp->Control_2);
7502 int buf2_len = RXD_GET_BUFFER2_SIZE_3(rxdp->Control_2);
7503 unsigned char *buff = skb_push(skb, buf0_len);
7505 struct buffAdd *ba = &ring_data->ba[get_block][get_off];
7506 sp->stats.rx_bytes += buf0_len + buf2_len;
7507 memcpy(buff, ba->ba_0, buf0_len);
7508 skb_put(skb, buf2_len);
7511 if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) && ((!sp->lro) ||
7512 (sp->lro && (!(rxdp->Control_1 & RXD_FRAME_IP_FRAG)))) &&
7514 l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1);
7515 l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1);
7516 if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) {
7518 * NIC verifies if the Checksum of the received
7519 * frame is Ok or not and accordingly returns
7520 * a flag in the RxD.
7522 skb->ip_summed = CHECKSUM_UNNECESSARY;
7528 ret = s2io_club_tcp_session(skb->data, &tcp,
7532 case 3: /* Begin anew */
7535 case 1: /* Aggregate */
7537 lro_append_pkt(sp, lro,
7541 case 4: /* Flush session */
7543 lro_append_pkt(sp, lro,
7545 queue_rx_frame(lro->parent,
7547 clear_lro_session(lro);
7548 sp->mac_control.stats_info->
7549 sw_stat.flush_max_pkts++;
7552 case 2: /* Flush both */
7553 lro->parent->data_len =
7555 sp->mac_control.stats_info->
7556 sw_stat.sending_both++;
7557 queue_rx_frame(lro->parent,
7559 clear_lro_session(lro);
7561 case 0: /* sessions exceeded */
7562 case -1: /* non-TCP or not
7566 * First pkt in session not
7567 * L3/L4 aggregatable
7572 "%s: Samadhana!!\n",
7579 * Packet with erroneous checksum, let the
7580 * upper layers deal with it.
7582 skb->ip_summed = CHECKSUM_NONE;
7585 skb->ip_summed = CHECKSUM_NONE;
7587 sp->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
7589 queue_rx_frame(skb, RXD_GET_VLAN_TAG(rxdp->Control_2));
7590 dev->last_rx = jiffies;
7592 atomic_dec(&sp->rx_bufs_left[ring_no]);
7597 * s2io_link - stops/starts the Tx queue.
7598 * @sp : private member of the device structure, which is a pointer to the
7599 * s2io_nic structure.
7600 * @link : inidicates whether link is UP/DOWN.
7602 * This function stops/starts the Tx queue depending on whether the link
7603 * status of the NIC is is down or up. This is called by the Alarm
7604 * interrupt handler whenever a link change interrupt comes up.
7609 static void s2io_link(struct s2io_nic * sp, int link)
7611 struct net_device *dev = (struct net_device *) sp->dev;
7613 if (link != sp->last_link_state) {
7615 if (link == LINK_DOWN) {
7616 DBG_PRINT(ERR_DBG, "%s: Link down\n", dev->name);
7617 s2io_stop_all_tx_queue(sp);
7618 netif_carrier_off(dev);
7619 if(sp->mac_control.stats_info->sw_stat.link_up_cnt)
7620 sp->mac_control.stats_info->sw_stat.link_up_time =
7621 jiffies - sp->start_time;
7622 sp->mac_control.stats_info->sw_stat.link_down_cnt++;
7624 DBG_PRINT(ERR_DBG, "%s: Link Up\n", dev->name);
7625 if (sp->mac_control.stats_info->sw_stat.link_down_cnt)
7626 sp->mac_control.stats_info->sw_stat.link_down_time =
7627 jiffies - sp->start_time;
7628 sp->mac_control.stats_info->sw_stat.link_up_cnt++;
7629 netif_carrier_on(dev);
7630 s2io_wake_all_tx_queue(sp);
7633 sp->last_link_state = link;
7634 sp->start_time = jiffies;
7638 * s2io_init_pci -Initialization of PCI and PCI-X configuration registers .
7639 * @sp : private member of the device structure, which is a pointer to the
7640 * s2io_nic structure.
7642 * This function initializes a few of the PCI and PCI-X configuration registers
7643 * with recommended values.
7648 static void s2io_init_pci(struct s2io_nic * sp)
7650 u16 pci_cmd = 0, pcix_cmd = 0;
7652 /* Enable Data Parity Error Recovery in PCI-X command register. */
7653 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7655 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7657 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7660 /* Set the PErr Response bit in PCI command register. */
7661 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7662 pci_write_config_word(sp->pdev, PCI_COMMAND,
7663 (pci_cmd | PCI_COMMAND_PARITY));
7664 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7667 static int s2io_verify_parm(struct pci_dev *pdev, u8 *dev_intr_type,
7670 if ((tx_fifo_num > MAX_TX_FIFOS) ||
7671 (tx_fifo_num < 1)) {
7672 DBG_PRINT(ERR_DBG, "s2io: Requested number of tx fifos "
7673 "(%d) not supported\n", tx_fifo_num);
7675 if (tx_fifo_num < 1)
7678 tx_fifo_num = MAX_TX_FIFOS;
7680 DBG_PRINT(ERR_DBG, "s2io: Default to %d ", tx_fifo_num);
7681 DBG_PRINT(ERR_DBG, "tx fifos\n");
7684 #ifndef CONFIG_NETDEVICES_MULTIQUEUE
7686 DBG_PRINT(ERR_DBG, "s2io: Multiqueue support not enabled\n");
7691 *dev_multiq = multiq;
7693 if (tx_steering_type && (1 == tx_fifo_num)) {
7694 if (tx_steering_type != TX_DEFAULT_STEERING)
7696 "s2io: Tx steering is not supported with "
7697 "one fifo. Disabling Tx steering.\n");
7698 tx_steering_type = NO_STEERING;
7701 if ((tx_steering_type < NO_STEERING) ||
7702 (tx_steering_type > TX_DEFAULT_STEERING)) {
7703 DBG_PRINT(ERR_DBG, "s2io: Requested transmit steering not "
7705 DBG_PRINT(ERR_DBG, "s2io: Disabling transmit steering\n");
7706 tx_steering_type = NO_STEERING;
7709 if ( rx_ring_num > 8) {
7710 DBG_PRINT(ERR_DBG, "s2io: Requested number of Rx rings not "
7712 DBG_PRINT(ERR_DBG, "s2io: Default to 8 Rx rings\n");
7715 if (*dev_intr_type != INTA)
7718 if ((*dev_intr_type != INTA) && (*dev_intr_type != MSI_X)) {
7719 DBG_PRINT(ERR_DBG, "s2io: Wrong intr_type requested. "
7720 "Defaulting to INTA\n");
7721 *dev_intr_type = INTA;
7724 if ((*dev_intr_type == MSI_X) &&
7725 ((pdev->device != PCI_DEVICE_ID_HERC_WIN) &&
7726 (pdev->device != PCI_DEVICE_ID_HERC_UNI))) {
7727 DBG_PRINT(ERR_DBG, "s2io: Xframe I does not support MSI_X. "
7728 "Defaulting to INTA\n");
7729 *dev_intr_type = INTA;
7732 if ((rx_ring_mode != 1) && (rx_ring_mode != 2)) {
7733 DBG_PRINT(ERR_DBG, "s2io: Requested ring mode not supported\n");
7734 DBG_PRINT(ERR_DBG, "s2io: Defaulting to 1-buffer mode\n");
7741 * rts_ds_steer - Receive traffic steering based on IPv4 or IPv6 TOS
7742 * or Traffic class respectively.
7743 * @nic: device private variable
7744 * Description: The function configures the receive steering to
7745 * desired receive ring.
7746 * Return Value: SUCCESS on success and
7747 * '-1' on failure (endian settings incorrect).
7749 static int rts_ds_steer(struct s2io_nic *nic, u8 ds_codepoint, u8 ring)
7751 struct XENA_dev_config __iomem *bar0 = nic->bar0;
7752 register u64 val64 = 0;
7754 if (ds_codepoint > 63)
7757 val64 = RTS_DS_MEM_DATA(ring);
7758 writeq(val64, &bar0->rts_ds_mem_data);
7760 val64 = RTS_DS_MEM_CTRL_WE |
7761 RTS_DS_MEM_CTRL_STROBE_NEW_CMD |
7762 RTS_DS_MEM_CTRL_OFFSET(ds_codepoint);
7764 writeq(val64, &bar0->rts_ds_mem_ctrl);
7766 return wait_for_cmd_complete(&bar0->rts_ds_mem_ctrl,
7767 RTS_DS_MEM_CTRL_STROBE_CMD_BEING_EXECUTED,
7772 * s2io_init_nic - Initialization of the adapter .
7773 * @pdev : structure containing the PCI related information of the device.
7774 * @pre: List of PCI devices supported by the driver listed in s2io_tbl.
7776 * The function initializes an adapter identified by the pci_dec structure.
7777 * All OS related initialization including memory and device structure and
7778 * initlaization of the device private variable is done. Also the swapper
7779 * control register is initialized to enable read and write into the I/O
7780 * registers of the device.
7782 * returns 0 on success and negative on failure.
7785 static int __devinit
7786 s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
7788 struct s2io_nic *sp;
7789 struct net_device *dev;
7791 int dma_flag = FALSE;
7792 u32 mac_up, mac_down;
7793 u64 val64 = 0, tmp64 = 0;
7794 struct XENA_dev_config __iomem *bar0 = NULL;
7796 struct mac_info *mac_control;
7797 struct config_param *config;
7799 u8 dev_intr_type = intr_type;
7801 DECLARE_MAC_BUF(mac);
7803 ret = s2io_verify_parm(pdev, &dev_intr_type, &dev_multiq);
7807 if ((ret = pci_enable_device(pdev))) {
7809 "s2io_init_nic: pci_enable_device failed\n");
7813 if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
7814 DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 64bit DMA\n");
7816 if (pci_set_consistent_dma_mask
7817 (pdev, DMA_64BIT_MASK)) {
7819 "Unable to obtain 64bit DMA for \
7820 consistent allocations\n");
7821 pci_disable_device(pdev);
7824 } else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
7825 DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 32bit DMA\n");
7827 pci_disable_device(pdev);
7830 if ((ret = pci_request_regions(pdev, s2io_driver_name))) {
7831 DBG_PRINT(ERR_DBG, "%s: Request Regions failed - %x \n", __FUNCTION__, ret);
7832 pci_disable_device(pdev);
7835 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
7837 dev = alloc_etherdev_mq(sizeof(struct s2io_nic), tx_fifo_num);
7840 dev = alloc_etherdev(sizeof(struct s2io_nic));
7842 DBG_PRINT(ERR_DBG, "Device allocation failed\n");
7843 pci_disable_device(pdev);
7844 pci_release_regions(pdev);
7848 pci_set_master(pdev);
7849 pci_set_drvdata(pdev, dev);
7850 SET_NETDEV_DEV(dev, &pdev->dev);
7852 /* Private member variable initialized to s2io NIC structure */
7854 memset(sp, 0, sizeof(struct s2io_nic));
7857 sp->high_dma_flag = dma_flag;
7858 sp->device_enabled_once = FALSE;
7859 if (rx_ring_mode == 1)
7860 sp->rxd_mode = RXD_MODE_1;
7861 if (rx_ring_mode == 2)
7862 sp->rxd_mode = RXD_MODE_3B;
7864 sp->config.intr_type = dev_intr_type;
7866 if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) ||
7867 (pdev->device == PCI_DEVICE_ID_HERC_UNI))
7868 sp->device_type = XFRAME_II_DEVICE;
7870 sp->device_type = XFRAME_I_DEVICE;
7872 sp->lro = lro_enable;
7874 /* Initialize some PCI/PCI-X fields of the NIC. */
7878 * Setting the device configuration parameters.
7879 * Most of these parameters can be specified by the user during
7880 * module insertion as they are module loadable parameters. If
7881 * these parameters are not not specified during load time, they
7882 * are initialized with default values.
7884 mac_control = &sp->mac_control;
7885 config = &sp->config;
7887 config->napi = napi;
7888 config->tx_steering_type = tx_steering_type;
7890 /* Tx side parameters. */
7891 if (config->tx_steering_type == TX_PRIORITY_STEERING)
7892 config->tx_fifo_num = MAX_TX_FIFOS;
7894 config->tx_fifo_num = tx_fifo_num;
7896 /* Initialize the fifos used for tx steering */
7897 if (config->tx_fifo_num < 5) {
7898 if (config->tx_fifo_num == 1)
7899 sp->total_tcp_fifos = 1;
7901 sp->total_tcp_fifos = config->tx_fifo_num - 1;
7902 sp->udp_fifo_idx = config->tx_fifo_num - 1;
7903 sp->total_udp_fifos = 1;
7904 sp->other_fifo_idx = sp->total_tcp_fifos - 1;
7906 sp->total_tcp_fifos = (tx_fifo_num - FIFO_UDP_MAX_NUM -
7907 FIFO_OTHER_MAX_NUM);
7908 sp->udp_fifo_idx = sp->total_tcp_fifos;
7909 sp->total_udp_fifos = FIFO_UDP_MAX_NUM;
7910 sp->other_fifo_idx = sp->udp_fifo_idx + FIFO_UDP_MAX_NUM;
7913 config->multiq = dev_multiq;
7914 for (i = 0; i < config->tx_fifo_num; i++) {
7915 config->tx_cfg[i].fifo_len = tx_fifo_len[i];
7916 config->tx_cfg[i].fifo_priority = i;
7919 /* mapping the QoS priority to the configured fifos */
7920 for (i = 0; i < MAX_TX_FIFOS; i++)
7921 config->fifo_mapping[i] = fifo_map[config->tx_fifo_num - 1][i];
7923 /* map the hashing selector table to the configured fifos */
7924 for (i = 0; i < config->tx_fifo_num; i++)
7925 sp->fifo_selector[i] = fifo_selector[i];
7928 config->tx_intr_type = TXD_INT_TYPE_UTILZ;
7929 for (i = 0; i < config->tx_fifo_num; i++) {
7930 config->tx_cfg[i].f_no_snoop =
7931 (NO_SNOOP_TXD | NO_SNOOP_TXD_BUFFER);
7932 if (config->tx_cfg[i].fifo_len < 65) {
7933 config->tx_intr_type = TXD_INT_TYPE_PER_LIST;
7937 /* + 2 because one Txd for skb->data and one Txd for UFO */
7938 config->max_txds = MAX_SKB_FRAGS + 2;
7940 /* Rx side parameters. */
7941 config->rx_ring_num = rx_ring_num;
7942 for (i = 0; i < MAX_RX_RINGS; i++) {
7943 config->rx_cfg[i].num_rxd = rx_ring_sz[i] *
7944 (rxd_count[sp->rxd_mode] + 1);
7945 config->rx_cfg[i].ring_priority = i;
7948 for (i = 0; i < rx_ring_num; i++) {
7949 config->rx_cfg[i].ring_org = RING_ORG_BUFF1;
7950 config->rx_cfg[i].f_no_snoop =
7951 (NO_SNOOP_RXD | NO_SNOOP_RXD_BUFFER);
7954 /* Setting Mac Control parameters */
7955 mac_control->rmac_pause_time = rmac_pause_time;
7956 mac_control->mc_pause_threshold_q0q3 = mc_pause_threshold_q0q3;
7957 mac_control->mc_pause_threshold_q4q7 = mc_pause_threshold_q4q7;
7960 /* Initialize Ring buffer parameters. */
7961 for (i = 0; i < config->rx_ring_num; i++)
7962 atomic_set(&sp->rx_bufs_left[i], 0);
7964 /* initialize the shared memory used by the NIC and the host */
7965 if (init_shared_mem(sp)) {
7966 DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n",
7969 goto mem_alloc_failed;
7972 sp->bar0 = ioremap(pci_resource_start(pdev, 0),
7973 pci_resource_len(pdev, 0));
7975 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem1\n",
7978 goto bar0_remap_failed;
7981 sp->bar1 = ioremap(pci_resource_start(pdev, 2),
7982 pci_resource_len(pdev, 2));
7984 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem2\n",
7987 goto bar1_remap_failed;
7990 dev->irq = pdev->irq;
7991 dev->base_addr = (unsigned long) sp->bar0;
7993 /* Initializing the BAR1 address as the start of the FIFO pointer. */
7994 for (j = 0; j < MAX_TX_FIFOS; j++) {
7995 mac_control->tx_FIFO_start[j] = (struct TxFIFO_element __iomem *)
7996 (sp->bar1 + (j * 0x00020000));
7999 /* Driver entry points */
8000 dev->open = &s2io_open;
8001 dev->stop = &s2io_close;
8002 dev->hard_start_xmit = &s2io_xmit;
8003 dev->get_stats = &s2io_get_stats;
8004 dev->set_multicast_list = &s2io_set_multicast;
8005 dev->do_ioctl = &s2io_ioctl;
8006 dev->set_mac_address = &s2io_set_mac_addr;
8007 dev->change_mtu = &s2io_change_mtu;
8008 SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
8009 dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
8010 dev->vlan_rx_register = s2io_vlan_rx_register;
8011 dev->vlan_rx_kill_vid = (void *)s2io_vlan_rx_kill_vid;
8014 * will use eth_mac_addr() for dev->set_mac_address
8015 * mac address will be set every time dev->open() is called
8017 netif_napi_add(dev, &sp->napi, s2io_poll, 32);
8019 #ifdef CONFIG_NET_POLL_CONTROLLER
8020 dev->poll_controller = s2io_netpoll;
8023 dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
8024 if (sp->high_dma_flag == TRUE)
8025 dev->features |= NETIF_F_HIGHDMA;
8026 dev->features |= NETIF_F_TSO;
8027 dev->features |= NETIF_F_TSO6;
8028 if ((sp->device_type & XFRAME_II_DEVICE) && (ufo)) {
8029 dev->features |= NETIF_F_UFO;
8030 dev->features |= NETIF_F_HW_CSUM;
8032 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
8034 dev->features |= NETIF_F_MULTI_QUEUE;
8036 dev->tx_timeout = &s2io_tx_watchdog;
8037 dev->watchdog_timeo = WATCH_DOG_TIMEOUT;
8038 INIT_WORK(&sp->rst_timer_task, s2io_restart_nic);
8039 INIT_WORK(&sp->set_link_task, s2io_set_link);
8041 pci_save_state(sp->pdev);
8043 /* Setting swapper control on the NIC, for proper reset operation */
8044 if (s2io_set_swapper(sp)) {
8045 DBG_PRINT(ERR_DBG, "%s:swapper settings are wrong\n",
8048 goto set_swap_failed;
8051 /* Verify if the Herc works on the slot its placed into */
8052 if (sp->device_type & XFRAME_II_DEVICE) {
8053 mode = s2io_verify_pci_mode(sp);
8055 DBG_PRINT(ERR_DBG, "%s: ", __FUNCTION__);
8056 DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
8058 goto set_swap_failed;
8062 /* Not needed for Herc */
8063 if (sp->device_type & XFRAME_I_DEVICE) {
8065 * Fix for all "FFs" MAC address problems observed on
8068 fix_mac_address(sp);
8073 * MAC address initialization.
8074 * For now only one mac address will be read and used.
8077 val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
8078 RMAC_ADDR_CMD_MEM_OFFSET(0 + S2IO_MAC_ADDR_START_OFFSET);
8079 writeq(val64, &bar0->rmac_addr_cmd_mem);
8080 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
8081 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING, S2IO_BIT_RESET);
8082 tmp64 = readq(&bar0->rmac_addr_data0_mem);
8083 mac_down = (u32) tmp64;
8084 mac_up = (u32) (tmp64 >> 32);
8086 sp->def_mac_addr[0].mac_addr[3] = (u8) (mac_up);
8087 sp->def_mac_addr[0].mac_addr[2] = (u8) (mac_up >> 8);
8088 sp->def_mac_addr[0].mac_addr[1] = (u8) (mac_up >> 16);
8089 sp->def_mac_addr[0].mac_addr[0] = (u8) (mac_up >> 24);
8090 sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16);
8091 sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24);
8093 /* Set the factory defined MAC address initially */
8094 dev->addr_len = ETH_ALEN;
8095 memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN);
8096 memcpy(dev->perm_addr, dev->dev_addr, ETH_ALEN);
8098 /* initialize number of multicast & unicast MAC entries variables */
8099 if (sp->device_type == XFRAME_I_DEVICE) {
8100 config->max_mc_addr = S2IO_XENA_MAX_MC_ADDRESSES;
8101 config->max_mac_addr = S2IO_XENA_MAX_MAC_ADDRESSES;
8102 config->mc_start_offset = S2IO_XENA_MC_ADDR_START_OFFSET;
8103 } else if (sp->device_type == XFRAME_II_DEVICE) {
8104 config->max_mc_addr = S2IO_HERC_MAX_MC_ADDRESSES;
8105 config->max_mac_addr = S2IO_HERC_MAX_MAC_ADDRESSES;
8106 config->mc_start_offset = S2IO_HERC_MC_ADDR_START_OFFSET;
8109 /* store mac addresses from CAM to s2io_nic structure */
8110 do_s2io_store_unicast_mc(sp);
8112 /* Store the values of the MSIX table in the s2io_nic structure */
8113 store_xmsi_data(sp);
8114 /* reset Nic and bring it to known state */
8118 * Initialize the tasklet status and link state flags
8119 * and the card state parameter
8121 sp->tasklet_status = 0;
8124 /* Initialize spinlocks */
8125 for (i = 0; i < sp->config.tx_fifo_num; i++)
8126 spin_lock_init(&mac_control->fifos[i].tx_lock);
8129 spin_lock_init(&sp->put_lock);
8130 spin_lock_init(&sp->rx_lock);
8133 * SXE-002: Configure link and activity LED to init state
8136 subid = sp->pdev->subsystem_device;
8137 if ((subid & 0xFF) >= 0x07) {
8138 val64 = readq(&bar0->gpio_control);
8139 val64 |= 0x0000800000000000ULL;
8140 writeq(val64, &bar0->gpio_control);
8141 val64 = 0x0411040400000000ULL;
8142 writeq(val64, (void __iomem *) bar0 + 0x2700);
8143 val64 = readq(&bar0->gpio_control);
8146 sp->rx_csum = 1; /* Rx chksum verify enabled by default */
8148 if (register_netdev(dev)) {
8149 DBG_PRINT(ERR_DBG, "Device registration failed\n");
8151 goto register_failed;
8154 DBG_PRINT(ERR_DBG, "Copyright(c) 2002-2007 Neterion Inc.\n");
8155 DBG_PRINT(ERR_DBG, "%s: Neterion %s (rev %d)\n",dev->name,
8156 sp->product_name, pdev->revision);
8157 DBG_PRINT(ERR_DBG, "%s: Driver version %s\n", dev->name,
8158 s2io_driver_version);
8159 DBG_PRINT(ERR_DBG, "%s: MAC ADDR: %s\n",
8160 dev->name, print_mac(mac, dev->dev_addr));
8161 DBG_PRINT(ERR_DBG, "SERIAL NUMBER: %s\n", sp->serial_num);
8162 if (sp->device_type & XFRAME_II_DEVICE) {
8163 mode = s2io_print_pci_mode(sp);
8165 DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
8167 unregister_netdev(dev);
8168 goto set_swap_failed;
8171 switch(sp->rxd_mode) {
8173 DBG_PRINT(ERR_DBG, "%s: 1-Buffer receive mode enabled\n",
8177 DBG_PRINT(ERR_DBG, "%s: 2-Buffer receive mode enabled\n",
8183 DBG_PRINT(ERR_DBG, "%s: NAPI enabled\n", dev->name);
8185 DBG_PRINT(ERR_DBG, "%s: Using %d Tx fifo(s)\n", dev->name,
8186 sp->config.tx_fifo_num);
8188 switch(sp->config.intr_type) {
8190 DBG_PRINT(ERR_DBG, "%s: Interrupt type INTA\n", dev->name);
8193 DBG_PRINT(ERR_DBG, "%s: Interrupt type MSI-X\n", dev->name);
8196 if (sp->config.multiq) {
8197 for (i = 0; i < sp->config.tx_fifo_num; i++)
8198 mac_control->fifos[i].multiq = config->multiq;
8199 DBG_PRINT(ERR_DBG, "%s: Multiqueue support enabled\n",
8202 DBG_PRINT(ERR_DBG, "%s: Multiqueue support disabled\n",
8205 switch (sp->config.tx_steering_type) {
8207 DBG_PRINT(ERR_DBG, "%s: No steering enabled for"
8208 " transmit\n", dev->name);
8210 case TX_PRIORITY_STEERING:
8211 DBG_PRINT(ERR_DBG, "%s: Priority steering enabled for"
8212 " transmit\n", dev->name);
8214 case TX_DEFAULT_STEERING:
8215 DBG_PRINT(ERR_DBG, "%s: Default steering enabled for"
8216 " transmit\n", dev->name);
8220 DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
8223 DBG_PRINT(ERR_DBG, "%s: UDP Fragmentation Offload(UFO)"
8224 " enabled\n", dev->name);
8225 /* Initialize device name */
8226 sprintf(sp->name, "%s Neterion %s", dev->name, sp->product_name);
8229 * Make Link state as off at this point, when the Link change
8230 * interrupt comes the state will be automatically changed to
8233 netif_carrier_off(dev);
8244 free_shared_mem(sp);
8245 pci_disable_device(pdev);
8246 pci_release_regions(pdev);
8247 pci_set_drvdata(pdev, NULL);
8254 * s2io_rem_nic - Free the PCI device
8255 * @pdev: structure containing the PCI related information of the device.
8256 * Description: This function is called by the Pci subsystem to release a
8257 * PCI device and free up all resource held up by the device. This could
8258 * be in response to a Hot plug event or when the driver is to be removed
8262 static void __devexit s2io_rem_nic(struct pci_dev *pdev)
8264 struct net_device *dev =
8265 (struct net_device *) pci_get_drvdata(pdev);
8266 struct s2io_nic *sp;
8269 DBG_PRINT(ERR_DBG, "Driver Data is NULL!!\n");
8273 flush_scheduled_work();
8276 unregister_netdev(dev);
8278 free_shared_mem(sp);
8281 pci_release_regions(pdev);
8282 pci_set_drvdata(pdev, NULL);
8284 pci_disable_device(pdev);
8288 * s2io_starter - Entry point for the driver
8289 * Description: This function is the entry point for the driver. It verifies
8290 * the module loadable parameters and initializes PCI configuration space.
8293 static int __init s2io_starter(void)
8295 return pci_register_driver(&s2io_driver);
8299 * s2io_closer - Cleanup routine for the driver
8300 * Description: This function is the cleanup routine for the driver. It unregist * ers the driver.
8303 static __exit void s2io_closer(void)
8305 pci_unregister_driver(&s2io_driver);
8306 DBG_PRINT(INIT_DBG, "cleanup done\n");
8309 module_init(s2io_starter);
8310 module_exit(s2io_closer);
8312 static int check_L2_lro_capable(u8 *buffer, struct iphdr **ip,
8313 struct tcphdr **tcp, struct RxD_t *rxdp,
8314 struct s2io_nic *sp)
8317 u8 l2_type = (u8)((rxdp->Control_1 >> 37) & 0x7), ip_len;
8319 if (!(rxdp->Control_1 & RXD_FRAME_PROTO_TCP)) {
8320 DBG_PRINT(INIT_DBG,"%s: Non-TCP frames not supported for LRO\n",
8325 /* Checking for DIX type or DIX type with VLAN */
8327 || (l2_type == 4)) {
8328 ip_off = HEADER_ETHERNET_II_802_3_SIZE;
8330 * If vlan stripping is disabled and the frame is VLAN tagged,
8331 * shift the offset by the VLAN header size bytes.
8333 if ((!vlan_strip_flag) &&
8334 (rxdp->Control_1 & RXD_FRAME_VLAN_TAG))
8335 ip_off += HEADER_VLAN_SIZE;
8337 /* LLC, SNAP etc are considered non-mergeable */
8341 *ip = (struct iphdr *)((u8 *)buffer + ip_off);
8342 ip_len = (u8)((*ip)->ihl);
8344 *tcp = (struct tcphdr *)((unsigned long)*ip + ip_len);
8349 static int check_for_socket_match(struct lro *lro, struct iphdr *ip,
8352 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8353 if ((lro->iph->saddr != ip->saddr) || (lro->iph->daddr != ip->daddr) ||
8354 (lro->tcph->source != tcp->source) || (lro->tcph->dest != tcp->dest))
8359 static inline int get_l4_pyld_length(struct iphdr *ip, struct tcphdr *tcp)
8361 return(ntohs(ip->tot_len) - (ip->ihl << 2) - (tcp->doff << 2));
8364 static void initiate_new_session(struct lro *lro, u8 *l2h,
8365 struct iphdr *ip, struct tcphdr *tcp, u32 tcp_pyld_len, u16 vlan_tag)
8367 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8371 lro->tcp_next_seq = tcp_pyld_len + ntohl(tcp->seq);
8372 lro->tcp_ack = tcp->ack_seq;
8374 lro->total_len = ntohs(ip->tot_len);
8376 lro->vlan_tag = vlan_tag;
8378 * check if we saw TCP timestamp. Other consistency checks have
8379 * already been done.
8381 if (tcp->doff == 8) {
8383 ptr = (__be32 *)(tcp+1);
8385 lro->cur_tsval = ntohl(*(ptr+1));
8386 lro->cur_tsecr = *(ptr+2);
8391 static void update_L3L4_header(struct s2io_nic *sp, struct lro *lro)
8393 struct iphdr *ip = lro->iph;
8394 struct tcphdr *tcp = lro->tcph;
8396 struct stat_block *statinfo = sp->mac_control.stats_info;
8397 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8399 /* Update L3 header */
8400 ip->tot_len = htons(lro->total_len);
8402 nchk = ip_fast_csum((u8 *)lro->iph, ip->ihl);
8405 /* Update L4 header */
8406 tcp->ack_seq = lro->tcp_ack;
8407 tcp->window = lro->window;
8409 /* Update tsecr field if this session has timestamps enabled */
8411 __be32 *ptr = (__be32 *)(tcp + 1);
8412 *(ptr+2) = lro->cur_tsecr;
8415 /* Update counters required for calculation of
8416 * average no. of packets aggregated.
8418 statinfo->sw_stat.sum_avg_pkts_aggregated += lro->sg_num;
8419 statinfo->sw_stat.num_aggregations++;
8422 static void aggregate_new_rx(struct lro *lro, struct iphdr *ip,
8423 struct tcphdr *tcp, u32 l4_pyld)
8425 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8426 lro->total_len += l4_pyld;
8427 lro->frags_len += l4_pyld;
8428 lro->tcp_next_seq += l4_pyld;
8431 /* Update ack seq no. and window ad(from this pkt) in LRO object */
8432 lro->tcp_ack = tcp->ack_seq;
8433 lro->window = tcp->window;
8437 /* Update tsecr and tsval from this packet */
8438 ptr = (__be32 *)(tcp+1);
8439 lro->cur_tsval = ntohl(*(ptr+1));
8440 lro->cur_tsecr = *(ptr + 2);
8444 static int verify_l3_l4_lro_capable(struct lro *l_lro, struct iphdr *ip,
8445 struct tcphdr *tcp, u32 tcp_pyld_len)
8449 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8451 if (!tcp_pyld_len) {
8452 /* Runt frame or a pure ack */
8456 if (ip->ihl != 5) /* IP has options */
8459 /* If we see CE codepoint in IP header, packet is not mergeable */
8460 if (INET_ECN_is_ce(ipv4_get_dsfield(ip)))
8463 /* If we see ECE or CWR flags in TCP header, packet is not mergeable */
8464 if (tcp->urg || tcp->psh || tcp->rst || tcp->syn || tcp->fin ||
8465 tcp->ece || tcp->cwr || !tcp->ack) {
8467 * Currently recognize only the ack control word and
8468 * any other control field being set would result in
8469 * flushing the LRO session
8475 * Allow only one TCP timestamp option. Don't aggregate if
8476 * any other options are detected.
8478 if (tcp->doff != 5 && tcp->doff != 8)
8481 if (tcp->doff == 8) {
8482 ptr = (u8 *)(tcp + 1);
8483 while (*ptr == TCPOPT_NOP)
8485 if (*ptr != TCPOPT_TIMESTAMP || *(ptr+1) != TCPOLEN_TIMESTAMP)
8488 /* Ensure timestamp value increases monotonically */
8490 if (l_lro->cur_tsval > ntohl(*((__be32 *)(ptr+2))))
8493 /* timestamp echo reply should be non-zero */
8494 if (*((__be32 *)(ptr+6)) == 0)
8502 s2io_club_tcp_session(u8 *buffer, u8 **tcp, u32 *tcp_len, struct lro **lro,
8503 struct RxD_t *rxdp, struct s2io_nic *sp)
8506 struct tcphdr *tcph;
8510 if (!(ret = check_L2_lro_capable(buffer, &ip, (struct tcphdr **)tcp,
8512 DBG_PRINT(INFO_DBG,"IP Saddr: %x Daddr: %x\n",
8513 ip->saddr, ip->daddr);
8517 vlan_tag = RXD_GET_VLAN_TAG(rxdp->Control_2);
8518 tcph = (struct tcphdr *)*tcp;
8519 *tcp_len = get_l4_pyld_length(ip, tcph);
8520 for (i=0; i<MAX_LRO_SESSIONS; i++) {
8521 struct lro *l_lro = &sp->lro0_n[i];
8522 if (l_lro->in_use) {
8523 if (check_for_socket_match(l_lro, ip, tcph))
8525 /* Sock pair matched */
8528 if ((*lro)->tcp_next_seq != ntohl(tcph->seq)) {
8529 DBG_PRINT(INFO_DBG, "%s:Out of order. expected "
8530 "0x%x, actual 0x%x\n", __FUNCTION__,
8531 (*lro)->tcp_next_seq,
8534 sp->mac_control.stats_info->
8535 sw_stat.outof_sequence_pkts++;
8540 if (!verify_l3_l4_lro_capable(l_lro, ip, tcph,*tcp_len))
8541 ret = 1; /* Aggregate */
8543 ret = 2; /* Flush both */
8549 /* Before searching for available LRO objects,
8550 * check if the pkt is L3/L4 aggregatable. If not
8551 * don't create new LRO session. Just send this
8554 if (verify_l3_l4_lro_capable(NULL, ip, tcph, *tcp_len)) {
8558 for (i=0; i<MAX_LRO_SESSIONS; i++) {
8559 struct lro *l_lro = &sp->lro0_n[i];
8560 if (!(l_lro->in_use)) {
8562 ret = 3; /* Begin anew */
8568 if (ret == 0) { /* sessions exceeded */
8569 DBG_PRINT(INFO_DBG,"%s:All LRO sessions already in use\n",
8577 initiate_new_session(*lro, buffer, ip, tcph, *tcp_len,
8581 update_L3L4_header(sp, *lro);
8584 aggregate_new_rx(*lro, ip, tcph, *tcp_len);
8585 if ((*lro)->sg_num == sp->lro_max_aggr_per_sess) {
8586 update_L3L4_header(sp, *lro);
8587 ret = 4; /* Flush the LRO */
8591 DBG_PRINT(ERR_DBG,"%s:Dont know, can't say!!\n",
8599 static void clear_lro_session(struct lro *lro)
8601 static u16 lro_struct_size = sizeof(struct lro);
8603 memset(lro, 0, lro_struct_size);
8606 static void queue_rx_frame(struct sk_buff *skb, u16 vlan_tag)
8608 struct net_device *dev = skb->dev;
8609 struct s2io_nic *sp = dev->priv;
8611 skb->protocol = eth_type_trans(skb, dev);
8612 if (sp->vlgrp && vlan_tag
8613 && (vlan_strip_flag)) {
8614 /* Queueing the vlan frame to the upper layer */
8615 if (sp->config.napi)
8616 vlan_hwaccel_receive_skb(skb, sp->vlgrp, vlan_tag);
8618 vlan_hwaccel_rx(skb, sp->vlgrp, vlan_tag);
8620 if (sp->config.napi)
8621 netif_receive_skb(skb);
8627 static void lro_append_pkt(struct s2io_nic *sp, struct lro *lro,
8628 struct sk_buff *skb,
8631 struct sk_buff *first = lro->parent;
8633 first->len += tcp_len;
8634 first->data_len = lro->frags_len;
8635 skb_pull(skb, (skb->len - tcp_len));
8636 if (skb_shinfo(first)->frag_list)
8637 lro->last_frag->next = skb;
8639 skb_shinfo(first)->frag_list = skb;
8640 first->truesize += skb->truesize;
8641 lro->last_frag = skb;
8642 sp->mac_control.stats_info->sw_stat.clubbed_frms_cnt++;
8647 * s2io_io_error_detected - called when PCI error is detected
8648 * @pdev: Pointer to PCI device
8649 * @state: The current pci connection state
8651 * This function is called after a PCI bus error affecting
8652 * this device has been detected.
8654 static pci_ers_result_t s2io_io_error_detected(struct pci_dev *pdev,
8655 pci_channel_state_t state)
8657 struct net_device *netdev = pci_get_drvdata(pdev);
8658 struct s2io_nic *sp = netdev->priv;
8660 netif_device_detach(netdev);
8662 if (netif_running(netdev)) {
8663 /* Bring down the card, while avoiding PCI I/O */
8664 do_s2io_card_down(sp, 0);
8666 pci_disable_device(pdev);
8668 return PCI_ERS_RESULT_NEED_RESET;
8672 * s2io_io_slot_reset - called after the pci bus has been reset.
8673 * @pdev: Pointer to PCI device
8675 * Restart the card from scratch, as if from a cold-boot.
8676 * At this point, the card has exprienced a hard reset,
8677 * followed by fixups by BIOS, and has its config space
8678 * set up identically to what it was at cold boot.
8680 static pci_ers_result_t s2io_io_slot_reset(struct pci_dev *pdev)
8682 struct net_device *netdev = pci_get_drvdata(pdev);
8683 struct s2io_nic *sp = netdev->priv;
8685 if (pci_enable_device(pdev)) {
8686 printk(KERN_ERR "s2io: "
8687 "Cannot re-enable PCI device after reset.\n");
8688 return PCI_ERS_RESULT_DISCONNECT;
8691 pci_set_master(pdev);
8694 return PCI_ERS_RESULT_RECOVERED;
8698 * s2io_io_resume - called when traffic can start flowing again.
8699 * @pdev: Pointer to PCI device
8701 * This callback is called when the error recovery driver tells
8702 * us that its OK to resume normal operation.
8704 static void s2io_io_resume(struct pci_dev *pdev)
8706 struct net_device *netdev = pci_get_drvdata(pdev);
8707 struct s2io_nic *sp = netdev->priv;
8709 if (netif_running(netdev)) {
8710 if (s2io_card_up(sp)) {
8711 printk(KERN_ERR "s2io: "
8712 "Can't bring device back up after reset.\n");
8716 if (s2io_set_mac_addr(netdev, netdev->dev_addr) == FAILURE) {
8718 printk(KERN_ERR "s2io: "
8719 "Can't resetore mac addr after reset.\n");
8724 netif_device_attach(netdev);
8725 netif_wake_queue(netdev);