xen_play_dead() is __cpuinit

[linux-2.6-omap-h63xx.git] / Documentation / usb / error-codes.txt

diff --git a/Documentation/usb/error-codes.txt b/Documentation/usb/error-codes.txt
index 1e36f1661cd0a6409a00defea1407162a9bdfa61..9cf83e8c27b8f94208d7ad0ebc4587d82430164d 100644 (file)
--- a/Documentation/usb/error-codes.txt
+++ b/Documentation/usb/error-codes.txt
@@ -46,8 +46,9 @@ USB-specific:
 
 -EMSGSIZE      (a) endpoint maxpacket size is zero; it is not usable
                    in the current interface altsetting.
 
 -EMSGSIZE      (a) endpoint maxpacket size is zero; it is not usable
                    in the current interface altsetting.

-               (b) ISO packet is biger than endpoint maxpacket
-               (c) requested data transfer size is invalid (negative)
+               (b) ISO packet is larger than the endpoint maxpacket.
+               (c) requested data transfer length is invalid: negative
+                   or too large for the host controller.

 
 -ENOSPC                This request would overcommit the usb bandwidth reserved
                for periodic transfers (interrupt, isochronous).
 
 -ENOSPC                This request would overcommit the usb bandwidth reserved
                for periodic transfers (interrupt, isochronous).


@@ -97,13 +98,13 @@ one or more packets could finish before an error stops further endpoint I/O.
                        error, a failure to respond (often caused by
                        device disconnect), or some other fault.
 
                        error, a failure to respond (often caused by
                        device disconnect), or some other fault.
 

--ETIMEDOUT (**)                No response packet received within the prescribed
+-ETIME (**)            No response packet received within the prescribed

                        bus turn-around time.  This error may instead be
                        reported as -EPROTO or -EILSEQ.
 
                        bus turn-around time.  This error may instead be
                        reported as -EPROTO or -EILSEQ.
 

-                       Note that the synchronous USB message functions
-                       also use this code to indicate timeout expired
-                       before the transfer completed.
+-ETIMEDOUT             Synchronous USB message functions use this code
+                       to indicate timeout expired before the transfer
+                       completed, and no other error was reported by HC.

 
 -EPIPE (**)            Endpoint stalled.  For non-control endpoints,
                        reset this status with usb_clear_halt().
 
 -EPIPE (**)            Endpoint stalled.  For non-control endpoints,
                        reset this status with usb_clear_halt().


@@ -125,7 +126,7 @@ one or more packets could finish before an error stops further endpoint I/O.
                        urb->transfer_flags.
 
 -ENODEV                        Device was removed.  Often preceded by a burst of
                        urb->transfer_flags.
 
 -ENODEV                        Device was removed.  Often preceded by a burst of

-                       other errors, since the hub driver does't detect
+                       other errors, since the hub driver doesn't detect

                        device removal events immediately.
 
 -EXDEV                 ISO transfer only partially completed
                        device removal events immediately.
 
 -EXDEV                 ISO transfer only partially completed


@@ -144,7 +145,7 @@ one or more packets could finish before an error stops further endpoint I/O.
 hardware problems such as bad devices (including firmware) or cables.
 
 (**) This is also one of several codes that different kinds of host
 hardware problems such as bad devices (including firmware) or cables.
 
 (**) This is also one of several codes that different kinds of host

-controller use to to indicate a transfer has failed because of device
+controller use to indicate a transfer has failed because of device

 disconnect.  In the interval before the hub driver starts disconnect
 processing, devices may receive such fault reports for every request.
 
 disconnect.  In the interval before the hub driver starts disconnect
 processing, devices may receive such fault reports for every request.
 


@@ -162,6 +163,3 @@ usb_get_*/usb_set_*():
 usb_control_msg():
 usb_bulk_msg():
 -ETIMEDOUT             Timeout expired before the transfer completed.
 usb_control_msg():
 usb_bulk_msg():
 -ETIMEDOUT             Timeout expired before the transfer completed.

-                       In the future this code may change to -ETIME,
-                       whose definition is a closer match to this sort
-                       of error.