[PATCH] ia64: note requirement for 8250_pnp, now that 8250_acpi is gone

[linux-2.6-omap-h63xx.git] / Documentation / powerpc / booting-without-of.txt

diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index ee551c6ea235a6f63f2df48bf35e9cb97a49a5a9..5c0ba235f5a5de9416244b8ef6417ed159987857 100644 (file)
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -719,6 +719,11 @@ address which can extend beyond that limit.
     - model : this is your board name/model
     - #address-cells : address representation for "root" devices
     - #size-cells: the size representation for "root" devices
+    - device_type : This property shouldn't be necessary. However, if
+      you decide to create a device_type for your root node, make sure it
+      is _not_ "chrp" unless your platform is a pSeries or PAPR compliant
+      one for 64-bit, or a CHRP-type machine for 32-bit as this will
+      matched by the kernel this way.
 
   Additionally, some recommended properties are:
 
@@ -1131,10 +1136,10 @@ Sense and level information should be encoded as follows:
    Devices connected to openPIC-compatible controllers should encode
    sense and polarity as follows:
 
-       0 = high to low edge sensitive type enabled
+       0 = low to high edge sensitive type enabled
        1 = active low level sensitive type enabled
-       2 = low to high edge sensitive type enabled
-       3 = active high level sensitive type enabled
+       2 = active high level sensitive type enabled
+       3 = high to low edge sensitive type enabled
 
    ISA PIC interrupt controllers should adhere to the ISA PIC
    encodings listed below:
@@ -1191,7 +1196,7 @@ platforms are moved over to use the flattened-device-tree model.
     - model : Model of the device.  Can be "TSEC", "eTSEC", or "FEC"
     - compatible : Should be "gianfar"
     - reg : Offset and length of the register set for the device
-    - address : List of bytes representing the ethernet address of
+    - mac-address : List of bytes representing the ethernet address of
       this controller
     - interrupts : <a b> where a is the interrupt number and b is a
       field that represents an encoding of the sense and level
@@ -1211,7 +1216,7 @@ platforms are moved over to use the flattened-device-tree model.
                model = "TSEC";
                compatible = "gianfar";
                reg = <24000 1000>;
-               address = [ 00 E0 0C 00 73 00 ];
+               mac-address = [ 00 E0 0C 00 73 00 ];
                interrupts = <d 3 e 3 12 3>;
                interrupt-parent = <40000>;
                phy-handle = <2452000>
@@ -1431,9 +1436,9 @@ platforms are moved over to use the flattened-device-tree model.
                interrupts = <1d 3>;
                interrupt-parent = <40000>;
                num-channels = <4>;
-               channel-fifo-len = <24>;
+               channel-fifo-len = <18>;
                exec-units-mask = <000000fe>;
-               descriptor-types-mask = <073f1127>;
+               descriptor-types-mask = <012b0ebf>;
        };
 
 
@@ -1493,7 +1498,7 @@ not necessary as they are usually the same as the root node.
                        model = "TSEC";
                        compatible = "gianfar";
                        reg = <24000 1000>;
-                       address = [ 00 E0 0C 00 73 00 ];
+                       mac-address = [ 00 E0 0C 00 73 00 ];
                        interrupts = <d 3 e 3 12 3>;
                        interrupt-parent = <40000>;
                        phy-handle = <2452000>;
@@ -1506,7 +1511,7 @@ not necessary as they are usually the same as the root node.
                        model = "TSEC";
                        compatible = "gianfar";
                        reg = <25000 1000>;
-                       address = [ 00 E0 0C 00 73 01 ];
+                       mac-address = [ 00 E0 0C 00 73 01 ];
                        interrupts = <13 3 14 3 18 3>;
                        interrupt-parent = <40000>;
                        phy-handle = <2452001>;
@@ -1519,7 +1524,7 @@ not necessary as they are usually the same as the root node.
                        model = "FEC";
                        compatible = "gianfar";
                        reg = <26000 1000>;
-                       address = [ 00 E0 0C 00 73 02 ];
+                       mac-address = [ 00 E0 0C 00 73 02 ];
                        interrupts = <19 3>;
                        interrupt-parent = <40000>;
                        phy-handle = <2452002>;