+//kernel/linux-omap-fsample/arch/arm/mach-omap1/clock.c#2 - edit change 3808 (text)
/*
* linux/arch/arm/mach-omap1/clock.c
*
#include <linux/clk.h>
#include <asm/io.h>
+#include <asm/mach-types.h>
+#include <asm/arch/cpu.h>
#include <asm/arch/usb.h>
#include <asm/arch/clock.h>
#include <asm/arch/sram.h>
/*
* In most cases we should not need to reprogram DPLL.
* Reprogramming the DPLL is tricky, it must be done from SRAM.
+ * (on 730, bit 13 must always be 1)
*/
- omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
+ if (cpu_is_omap730())
+ omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val | 0x2000);
+ else
+ omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
ck_dpll1.rate = ptr->pll_rate;
propagate_rate(&ck_dpll1);
*/
for (dsor = 2; dsor < 96; ++dsor) {
if ((dsor & 1) && dsor > 8)
- continue;
+ continue;
if (rate >= 96000000 / dsor)
break;
}
}
if (clk->flags & CLOCK_NO_IDLE_PARENT)
- if (!cpu_is_omap24xx())
- omap1_clk_deny_idle(clk->parent);
+ omap1_clk_deny_idle(clk->parent);
}
ret = clk->enable(clk);
if (likely(clk->parent)) {
omap1_clk_disable(clk->parent);
if (clk->flags & CLOCK_NO_IDLE_PARENT)
- if (!cpu_is_omap24xx())
- omap1_clk_allow_idle(clk->parent);
+ omap1_clk_allow_idle(clk->parent);
}
}
}
if (unlikely(clk->enable_reg == 0)) {
printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
clk->name);
- return 0;
+ return -EINVAL;
}
if (clk->flags & ENABLE_REG_32BIT) {
*-------------------------------------------------------------------------*/
#ifdef CONFIG_OMAP_RESET_CLOCKS
-/*
- * Resets some clocks that may be left on from bootloader,
- * but leaves serial clocks on. See also omap_late_clk_reset().
- */
-static inline void omap1_early_clk_reset(void)
-{
- //omap_writel(0x3 << 29, MOD_CONF_CTRL_0);
-}
-static int __init omap1_late_clk_reset(void)
+static void __init omap1_clk_disable_unused(struct clk *clk)
{
- /* Turn off all unused clocks */
- struct clk *p;
__u32 regval32;
- /* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
- regval32 = omap_readw(SOFT_REQ_REG) & (1 << 4);
- omap_writew(regval32, SOFT_REQ_REG);
- omap_writew(0, SOFT_REQ_REG2);
-
- list_for_each_entry(p, &clocks, node) {
- if (p->usecount > 0 || (p->flags & ALWAYS_ENABLED) ||
- p->enable_reg == 0)
- continue;
-
- /* Clocks in the DSP domain need api_ck. Just assume bootloader
- * has not enabled any DSP clocks */
- if ((u32)p->enable_reg == DSP_IDLECT2) {
- printk(KERN_INFO "Skipping reset check for DSP domain "
- "clock \"%s\"\n", p->name);
- continue;
- }
+ /* Clocks in the DSP domain need api_ck. Just assume bootloader
+ * has not enabled any DSP clocks */
+ if ((u32)clk->enable_reg == DSP_IDLECT2) {
+ printk(KERN_INFO "Skipping reset check for DSP domain "
+ "clock \"%s\"\n", clk->name);
+ return;
+ }
- /* Is the clock already disabled? */
- if (p->flags & ENABLE_REG_32BIT) {
- if (p->flags & VIRTUAL_IO_ADDRESS)
- regval32 = __raw_readl(p->enable_reg);
- else
- regval32 = omap_readl(p->enable_reg);
- } else {
- if (p->flags & VIRTUAL_IO_ADDRESS)
- regval32 = __raw_readw(p->enable_reg);
+ /* Is the clock already disabled? */
+ if (clk->flags & ENABLE_REG_32BIT) {
+ if (clk->flags & VIRTUAL_IO_ADDRESS)
+ regval32 = __raw_readl(clk->enable_reg);
else
- regval32 = omap_readw(p->enable_reg);
- }
-
- if ((regval32 & (1 << p->enable_bit)) == 0)
- continue;
+ regval32 = omap_readl(clk->enable_reg);
+ } else {
+ if (clk->flags & VIRTUAL_IO_ADDRESS)
+ regval32 = __raw_readw(clk->enable_reg);
+ else
+ regval32 = omap_readw(clk->enable_reg);
+ }
- /* FIXME: This clock seems to be necessary but no-one
- * has asked for its activation. */
- if (p == &tc2_ck // FIX: pm.c (SRAM), CCP, Camera
- || p == &ck_dpll1out.clk // FIX: SoSSI, SSR
- || p == &arm_gpio_ck // FIX: GPIO code for 1510
- ) {
- printk(KERN_INFO "FIXME: Clock \"%s\" seems unused\n",
- p->name);
- continue;
- }
+ if ((regval32 & (1 << clk->enable_bit)) == 0)
+ return;
- printk(KERN_INFO "Disabling unused clock \"%s\"... ", p->name);
- p->disable(p);
- printk(" done\n");
+ /* FIXME: This clock seems to be necessary but no-one
+ * has asked for its activation. */
+ if (clk == &tc2_ck // FIX: pm.c (SRAM), CCP, Camera
+ || clk == &ck_dpll1out.clk // FIX: SoSSI, SSR
+ || clk == &arm_gpio_ck // FIX: GPIO code for 1510
+ ) {
+ printk(KERN_INFO "FIXME: Clock \"%s\" seems unused\n",
+ clk->name);
+ return;
}
- return 0;
+ printk(KERN_INFO "Disabling unused clock \"%s\"... ", clk->name);
+ clk->disable(clk);
+ printk(" done\n");
}
-late_initcall(omap1_late_clk_reset);
#else
-#define omap1_early_clk_reset() {}
+#define omap1_clk_disable_unused NULL
#endif
static struct clk_functions omap1_clk_functions = {
.clk_disable = omap1_clk_disable,
.clk_round_rate = omap1_clk_round_rate,
.clk_set_rate = omap1_clk_set_rate,
+ .clk_disable_unused = omap1_clk_disable_unused,
};
int __init omap1_clk_init(void)
struct clk ** clkp;
const struct omap_clock_config *info;
int crystal_type = 0; /* Default 12 MHz */
+ u32 reg;
+
+#ifdef CONFIG_DEBUG_LL
+ /* Resets some clocks that may be left on from bootloader,
+ * but leaves serial clocks on.
+ */
+ omap_writel(0x3 << 29, MOD_CONF_CTRL_0);
+#endif
+
+ /* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
+ reg = omap_readw(SOFT_REQ_REG) & (1 << 4);
+ omap_writew(reg, SOFT_REQ_REG);
+ if (!cpu_is_omap15xx())
+ omap_writew(0, SOFT_REQ_REG2);
- omap1_early_clk_reset();
clk_init(&omap1_clk_functions);
/* By default all idlect1 clocks are allowed to idle */
clk_register(*clkp);
continue;
}
+
+ if (((*clkp)->flags &CLOCK_IN_OMAP310) && cpu_is_omap310()) {
+ clk_register(*clkp);
+ continue;
+ }
}
info = omap_get_config(OMAP_TAG_CLOCK, struct omap_clock_config);
if (info != NULL) {
- if (!cpu_is_omap1510())
+ if (!cpu_is_omap15xx())
crystal_type = info->system_clock_type;
}
printk(KERN_ERR "System frequencies not set. Check your config.\n");
/* Guess sane values (60MHz) */
omap_writew(0x2290, DPLL_CTL);
- omap_writew(0x1005, ARM_CKCTL);
+ omap_writew(cpu_is_omap730() ? 0x3005 : 0x1005, ARM_CKCTL);
ck_dpll1.rate = 60000000;
propagate_rate(&ck_dpll1);
}
ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10,
arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10);
-#ifdef CONFIG_MACH_OMAP_PERSEUS2
+#if defined(CONFIG_MACH_OMAP_PERSEUS2) || defined(CONFIG_MACH_OMAP_FSAMPLE)
/* Select slicer output as OMAP input clock */
omap_writew(omap_readw(OMAP730_PCC_UPLD_CTRL) & ~0x1, OMAP730_PCC_UPLD_CTRL);
#endif
+ /* Amstrad Delta wants BCLK high when inactive */
+ if (machine_is_ams_delta())
+ omap_writel(omap_readl(ULPD_CLOCK_CTRL) |
+ (1 << SDW_MCLK_INV_BIT),
+ ULPD_CLOCK_CTRL);
+
/* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */
- omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
+ /* (on 730, bit 13 must not be cleared) */
+ if (cpu_is_omap730())
+ omap_writew(omap_readw(ARM_CKCTL) & 0x2fff, ARM_CKCTL);
+ else
+ omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
/* Put DSP/MPUI into reset until needed */
omap_writew(0, ARM_RSTCT1);
clk_enable(&armxor_ck.clk);
clk_enable(&armtim_ck.clk); /* This should be done by timer code */
- if (cpu_is_omap1510())
+ if (cpu_is_omap15xx())
clk_enable(&arm_gpio_ck);
return 0;