depends on ARCH_OMAP24XX
select OMAP_DM_TIMER
select ARCH_OMAP_OTG
+ select CPU_V6
config ARCH_OMAP2430
bool "OMAP2430 support"
depends on ARCH_OMAP24XX
+ select ARCH_OMAP_OTG
+ select CPU_V6
config ARCH_OMAP34XX
bool "OMAP34xx Based System"
bool "OMAP3430 support"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
select ARCH_OMAP_OTG
+ select CPU_V7
comment "OMAP Board Type"
depends on ARCH_OMAP2 || ARCH_OMAP3
bool "Generic OMAP board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
+config MACH_NOKIA_N800
+ bool "Nokia N800"
+ depends on ARCH_OMAP2420
+ select VIDEO_TCM825X if VIDEO_OMAP2 && VIDEO_HELPER_CHIPS_AUTO
+ select CBUS if VIDEO_TCM825X
+ select CBUS_RETU if VIDEO_TCM825X
+ select MENELAUS if VIDEO_TCM825X
+ select OMAP_GPIO_SWITCH
+
+config MACH_NOKIA_N810
+ bool "Nokia N810"
+ depends on MACH_NOKIA_N800
+
+config MACH_NOKIA_N810_WIMAX
+ bool "Nokia N810 WiMAX"
+ depends on MACH_NOKIA_N800
+ select MACH_NOKIA_N810
+
+config MACH_NOKIA_RX51
+ bool "Nokia RX-51 board"
+ depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
+config MACH_OMAP2_TUSB6010
+ bool
+ depends on ARCH_OMAP2 && ARCH_OMAP2420
+ default y if MACH_NOKIA_N800
+
config MACH_OMAP_H4
bool "OMAP 2420 H4 board"
- depends on ARCH_OMAP2 && ARCH_OMAP24XX
+ depends on ARCH_OMAP2 && ARCH_OMAP2420
select OMAP_DEBUG_DEVICES
+config MACH_OMAP_H4_TUSB
+ bool "TUSB 6010 EVM board"
+ depends on MACH_OMAP_H4
+ select MACH_OMAP2_TUSB6010
+ help
+ Set this if you've got a TUSB6010 high speed USB board.
+ You may need to consult the schematics for your revisions
+ of the Menelaus and TUSB boards, and make changes to be
+ sure this is set up properly for your board stack.
+
+ Be sure to select OTG mode operation, not host-only or
+ peripheral-only.
+
+config MACH_OMAP_H4_OTG
+ bool "Use USB OTG connector, not device connector (S1.10)"
+ depends on MACH_OMAP_H4
+ help
+ Set this if you've set S1.10 (on the mainboard) to use the
+ Mini-AB (OTG) connector and OTG transceiver with the USB0
+ port, instead of the Mini-B ("download") connector with its
+ non-OTG transceiver.
+
+ Note that the "download" connector can be used to bootstrap
+ the system from the OMAP mask ROM. Also, since this is a
+ development platform, you can also force the OTG port into
+ a non-OTG operational mode.
+
+config MACH_OMAP2_H4_USB1
+ bool "Use USB1 port, not UART2 (S3.3)"
+ depends on MACH_OMAP_H4
+ help
+ Set this if you've set SW3.3 (on the CPU card) so that the
+ expansion connectors receive USB1 signals instead of UART2.
+
config MACH_OMAP_APOLLON
bool "OMAP 2420 Apollon board"
- depends on ARCH_OMAP2 && ARCH_OMAP24XX
+ depends on ARCH_OMAP2 && ARCH_OMAP2420
config MACH_OMAP_2430SDP
bool "OMAP 2430 SDP board"
+ depends on ARCH_OMAP2 && ARCH_OMAP2430
+
+config MACH_OMAP_LDP
+ bool "OMAP3 LDP board"
+ depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
+config MACH_OMAP2EVM
+ bool "OMAP 2530 EVM board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
-config MACH_OMAP3_BEAGLE
- bool "OMAP3 BEAGLE board"
+config MACH_OMAP_3430SDP
+ bool "OMAP 3430 SDP board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
-config MACH_OMAP_LDP
- bool "OMAP3 LDP board"
+config MACH_OMAP3EVM
+ bool "OMAP 3530 EVM board"
+ depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
+config MACH_OMAP3_BEAGLE
+ bool "OMAP3 BEAGLE board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
config MACH_OVERO