/*
* thermal support for the cell processor
*
+ * This module adds some sysfs attributes to cpu and spu nodes.
+ * Base for measurements are the digital thermal sensors (DTS)
+ * located on the chip.
+ * The accuracy is 2 degrees, starting from 65 up to 125 degrees celsius
+ * The attributes can be found under
+ * /sys/devices/system/cpu/cpuX/thermal
+ * /sys/devices/system/spu/spuX/thermal
+ *
+ * The following attributes are added for each node:
+ * temperature:
+ * contains the current temperature measured by the DTS
+ * throttle_begin:
+ * throttling begins when temperature is greater or equal to
+ * throttle_begin. Setting this value to 125 prevents throttling.
+ * throttle_end:
+ * throttling is being ceased, if the temperature is lower than
+ * throttle_end. Due to a delay between applying throttling and
+ * a reduced temperature this value should be less than throttle_begin.
+ * A value equal to throttle_begin provides only a very little hysteresis.
+ * throttle_full_stop:
+ * If the temperatrue is greater or equal to throttle_full_stop,
+ * full throttling is applied to the cpu or spu. This value should be
+ * greater than throttle_begin and throttle_end. Setting this value to
+ * 65 prevents the unit from running code at all.
+ *
* (C) Copyright IBM Deutschland Entwicklung GmbH 2005
*
* Author: Christian Krafft <krafft@de.ibm.com>
#include <asm/spu.h>
#include <asm/io.h>
#include <asm/prom.h>
+#include <asm/cell-regs.h>
-#include "cbe_regs.h"
#include "spu_priv1_mmio.h"
+#define TEMP_MIN 65
+#define TEMP_MAX 125
+
+#define SYSDEV_PREFIX_ATTR(_prefix,_name,_mode) \
+struct sysdev_attribute attr_ ## _prefix ## _ ## _name = { \
+ .attr = { .name = __stringify(_name), .mode = _mode }, \
+ .show = _prefix ## _show_ ## _name, \
+ .store = _prefix ## _store_ ## _name, \
+};
+
+static inline u8 reg_to_temp(u8 reg_value)
+{
+ return ((reg_value & 0x3f) << 1) + TEMP_MIN;
+}
+
+static inline u8 temp_to_reg(u8 temp)
+{
+ return ((temp - TEMP_MIN) >> 1) & 0x3f;
+}
+
static struct cbe_pmd_regs __iomem *get_pmd_regs(struct sys_device *sysdev)
{
struct spu *spu;
/* returns the value for a given spu in a given register */
static u8 spu_read_register_value(struct sys_device *sysdev, union spe_reg __iomem *reg)
{
- unsigned int *id;
union spe_reg value;
struct spu *spu;
- /* getting the id from the reg attribute will not work on future device-tree layouts
- * in future we should store the id to the spu struct and use it here */
spu = container_of(sysdev, struct spu, sysdev);
- id = (unsigned int *)get_property(spu_devnode(spu), "reg", NULL);
value.val = in_be64(®->val);
- return value.spe[*id];
+ return value.spe[spu->spe_id];
}
static ssize_t spu_show_temp(struct sys_device *sysdev, char *buf)
{
- int value;
+ u8 value;
struct cbe_pmd_regs __iomem *pmd_regs;
pmd_regs = get_pmd_regs(sysdev);
value = spu_read_register_value(sysdev, &pmd_regs->ts_ctsr1);
- /* clear all other bits */
+
+ return sprintf(buf, "%d\n", reg_to_temp(value));
+}
+
+static ssize_t show_throttle(struct cbe_pmd_regs __iomem *pmd_regs, char *buf, int pos)
+{
+ u64 value;
+
+ value = in_be64(&pmd_regs->tm_tpr.val);
+ /* access the corresponding byte */
+ value >>= pos;
value &= 0x3F;
- /* temp is stored in steps of 2 degrees */
- value *= 2;
- /* base temp is 65 degrees */
- value += 65;
- return sprintf(buf, "%d\n", (int) value);
+ return sprintf(buf, "%d\n", reg_to_temp(value));
+}
+
+static ssize_t store_throttle(struct cbe_pmd_regs __iomem *pmd_regs, const char *buf, size_t size, int pos)
+{
+ u64 reg_value;
+ int temp;
+ u64 new_value;
+ int ret;
+
+ ret = sscanf(buf, "%u", &temp);
+
+ if (ret != 1 || temp < TEMP_MIN || temp > TEMP_MAX)
+ return -EINVAL;
+
+ new_value = temp_to_reg(temp);
+
+ reg_value = in_be64(&pmd_regs->tm_tpr.val);
+
+ /* zero out bits for new value */
+ reg_value &= ~(0xffull << pos);
+ /* set bits to new value */
+ reg_value |= new_value << pos;
+
+ out_be64(&pmd_regs->tm_tpr.val, reg_value);
+ return size;
+}
+
+static ssize_t spu_show_throttle_end(struct sys_device *sysdev, char *buf)
+{
+ return show_throttle(get_pmd_regs(sysdev), buf, 0);
+}
+
+static ssize_t spu_show_throttle_begin(struct sys_device *sysdev, char *buf)
+{
+ return show_throttle(get_pmd_regs(sysdev), buf, 8);
+}
+
+static ssize_t spu_show_throttle_full_stop(struct sys_device *sysdev, char *buf)
+{
+ return show_throttle(get_pmd_regs(sysdev), buf, 16);
+}
+
+static ssize_t spu_store_throttle_end(struct sys_device *sysdev, const char *buf, size_t size)
+{
+ return store_throttle(get_pmd_regs(sysdev), buf, size, 0);
+}
+
+static ssize_t spu_store_throttle_begin(struct sys_device *sysdev, const char *buf, size_t size)
+{
+ return store_throttle(get_pmd_regs(sysdev), buf, size, 8);
+}
+
+static ssize_t spu_store_throttle_full_stop(struct sys_device *sysdev, const char *buf, size_t size)
+{
+ return store_throttle(get_pmd_regs(sysdev), buf, size, 16);
}
static ssize_t ppe_show_temp(struct sys_device *sysdev, char *buf, int pos)
pmd_regs = cbe_get_cpu_pmd_regs(sysdev->id);
value = in_be64(&pmd_regs->ts_ctsr2);
- /* access the corresponding byte */
- value >>= pos;
- /* clear all other bits */
- value &= 0x3F;
- /* temp is stored in steps of 2 degrees */
- value *= 2;
- /* base temp is 65 degrees */
- value += 65;
+ value = (value >> pos) & 0x3f;
- return sprintf(buf, "%d\n", (int) value);
+ return sprintf(buf, "%d\n", reg_to_temp(value));
}
return ppe_show_temp(sysdev, buf, 0);
}
+static ssize_t ppe_show_throttle_end(struct sys_device *sysdev, char *buf)
+{
+ return show_throttle(cbe_get_cpu_pmd_regs(sysdev->id), buf, 32);
+}
+
+static ssize_t ppe_show_throttle_begin(struct sys_device *sysdev, char *buf)
+{
+ return show_throttle(cbe_get_cpu_pmd_regs(sysdev->id), buf, 40);
+}
+
+static ssize_t ppe_show_throttle_full_stop(struct sys_device *sysdev, char *buf)
+{
+ return show_throttle(cbe_get_cpu_pmd_regs(sysdev->id), buf, 48);
+}
+
+static ssize_t ppe_store_throttle_end(struct sys_device *sysdev, const char *buf, size_t size)
+{
+ return store_throttle(cbe_get_cpu_pmd_regs(sysdev->id), buf, size, 32);
+}
+
+static ssize_t ppe_store_throttle_begin(struct sys_device *sysdev, const char *buf, size_t size)
+{
+ return store_throttle(cbe_get_cpu_pmd_regs(sysdev->id), buf, size, 40);
+}
+
+static ssize_t ppe_store_throttle_full_stop(struct sys_device *sysdev, const char *buf, size_t size)
+{
+ return store_throttle(cbe_get_cpu_pmd_regs(sysdev->id), buf, size, 48);
+}
+
+
static struct sysdev_attribute attr_spu_temperature = {
.attr = {.name = "temperature", .mode = 0400 },
.show = spu_show_temp,
};
+static SYSDEV_PREFIX_ATTR(spu, throttle_end, 0600);
+static SYSDEV_PREFIX_ATTR(spu, throttle_begin, 0600);
+static SYSDEV_PREFIX_ATTR(spu, throttle_full_stop, 0600);
+
+
static struct attribute *spu_attributes[] = {
&attr_spu_temperature.attr,
+ &attr_spu_throttle_end.attr,
+ &attr_spu_throttle_begin.attr,
+ &attr_spu_throttle_full_stop.attr,
NULL,
};
.show = ppe_show_temp1,
};
+static SYSDEV_PREFIX_ATTR(ppe, throttle_end, 0600);
+static SYSDEV_PREFIX_ATTR(ppe, throttle_begin, 0600);
+static SYSDEV_PREFIX_ATTR(ppe, throttle_full_stop, 0600);
+
static struct attribute *ppe_attributes[] = {
&attr_ppe_temperature0.attr,
&attr_ppe_temperature1.attr,
+ &attr_ppe_throttle_end.attr,
+ &attr_ppe_throttle_begin.attr,
+ &attr_ppe_throttle_full_stop.attr,
NULL,
};
/*
* initialize throttling with default values
*/
-static void __init init_default_values(void)
+static int __init init_default_values(void)
{
int cpu;
struct cbe_pmd_regs __iomem *pmd_regs;
for_each_possible_cpu (cpu) {
pr_debug("processing cpu %d\n", cpu);
sysdev = get_cpu_sysdev(cpu);
+
+ if (!sysdev) {
+ pr_info("invalid sysdev pointer for cbe_thermal\n");
+ return -EINVAL;
+ }
+
pmd_regs = cbe_get_cpu_pmd_regs(sysdev->id);
+ if (!pmd_regs) {
+ pr_info("invalid CBE regs pointer for cbe_thermal\n");
+ return -EINVAL;
+ }
+
out_be64(&pmd_regs->tm_str2, str2);
out_be64(&pmd_regs->tm_str1.val, str1.val);
out_be64(&pmd_regs->tm_tpr.val, tpr.val);
out_be64(&pmd_regs->tm_cr1.val, cr1.val);
out_be64(&pmd_regs->tm_cr2, cr2);
}
+
+ return 0;
}
static int __init thermal_init(void)
{
- init_default_values();
+ int rc = init_default_values();
- spu_add_sysdev_attr_group(&spu_attribute_group);
- cpu_add_sysdev_attr_group(&ppe_attribute_group);
+ if (rc == 0) {
+ spu_add_sysdev_attr_group(&spu_attribute_group);
+ cpu_add_sysdev_attr_group(&ppe_attribute_group);
+ }
- return 0;
+ return rc;
}
module_init(thermal_init);
projects / linux-2.6-omap-h63xx.git / blobdiff