#include <mach_ipi.h>
#include <mach_apic.h>
+/* Disable local APIC timer from the kernel commandline or via dmi quirk */
static int disable_apic_timer __cpuinitdata;
static int apic_calibrate_pmtmr __initdata;
int disable_apic;
static void lapic_timer_broadcast(cpumask_t mask);
static void apic_pm_activate(void);
+/*
+ * The local apic timer can be used for any function which is CPU local.
+ */
static struct clock_event_device lapic_clockevent = {
.name = "lapic",
.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT
static DEFINE_PER_CPU(struct clock_event_device, lapic_events);
static unsigned long apic_phys;
+unsigned int __cpuinitdata maxcpus = NR_CPUS;
unsigned long mp_lapic_addr;
-unsigned int __cpuinitdata maxcpus = NR_CPUS;
/*
* Get the LAPIC version
*/
}
/*
- * Check, if the APIC is integrated or a seperate chip
+ * Check, if the APIC is integrated or a separate chip
*/
static inline int lapic_is_integrated(void)
{
+#ifdef CONFIG_X86_64
return 1;
+#else
+ return APIC_INTEGRATED(lapic_get_version());
+#endif
}
/*
return lapic_get_version() >= 0x14;
}
+/*
+ * Paravirt kernels also might be using these below ops. So we still
+ * use generic apic_read()/apic_write(), which might be pointing to different
+ * ops in PARAVIRT case.
+ */
void xapic_wait_icr_idle(void)
{
while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
void xapic_icr_write(u32 low, u32 id)
{
- apic_write(APIC_ICR2, id << 24);
+ apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(id));
apic_write(APIC_ICR, low);
}
icr2 = apic_read(APIC_ICR2);
icr1 = apic_read(APIC_ICR);
- return (icr1 | ((u64)icr2 << 32));
+ return icr1 | ((u64)icr2 << 32);
}
static struct apic_ops xapic_ops = {
};
struct apic_ops __read_mostly *apic_ops = &xapic_ops;
-
EXPORT_SYMBOL_GPL(apic_ops);
static void x2apic_wait_icr_idle(void)
/* unmask and set to NMI */
v = APIC_DM_NMI;
+
+ /* Level triggered for 82489DX (32bit mode) */
+ if (!lapic_is_integrated())
+ v |= APIC_LVT_LEVEL_TRIGGER;
+
apic_write(APIC_LVT0, v);
}
*/
int lapic_get_maxlvt(void)
{
- unsigned int v, maxlvt;
+ unsigned int v;
v = apic_read(APIC_LVR);
- maxlvt = GET_APIC_MAXLVT(v);
- return maxlvt;
+ /*
+ * - we always have APIC integrated on 64bit mode
+ * - 82489DXs do not report # of LVT entries
+ */
+ return APIC_INTEGRATED(GET_APIC_VERSION(v)) ? GET_APIC_MAXLVT(v) : 2;
}
+/*
+ * Local APIC timer
+ */
+
+/* Clock divisor is set to 1 */
+#define APIC_DIVISOR 1
+
/*
* This function sets up the local APIC timer, with a timeout of
* 'clocks' APIC bus clock. During calibration we actually call
* We do reads before writes even if unnecessary, to get around the
* P5 APIC double write bug.
*/
-
static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
{
unsigned int lvtt_value, tmp_value;
lvtt_value = LOCAL_TIMER_VECTOR;
if (!oneshot)
lvtt_value |= APIC_LVT_TIMER_PERIODIC;
+ if (!lapic_is_integrated())
+ lvtt_value |= SET_APIC_TIMER_BASE(APIC_TIMER_BASE_DIV);
+
if (!irqen)
lvtt_value |= APIC_LVT_MASKED;
| APIC_TDR_DIV_16);
if (!oneshot)
- apic_write(APIC_TMICT, clocks);
+ apic_write(APIC_TMICT, clocks / APIC_DIVISOR);
}
/*
lapic_clockevent.min_delta_ns =
clockevent_delta2ns(0xF, &lapic_clockevent);
- calibration_result = result / HZ;
+ calibration_result = (result * APIC_DIVISOR) / HZ;
/*
* Do a sanity check on the APIC calibration result
void __init setup_boot_APIC_clock(void)
{
/*
- * The local apic timer can be disabled via the kernel commandline.
- * Register the lapic timer as a dummy clock event source on SMP
- * systems, so the broadcast mechanism is used. On UP systems simply
- * ignore it.
+ * The local apic timer can be disabled via the kernel
+ * commandline or from the CPU detection code. Register the lapic
+ * timer as a dummy clock event source on SMP systems, so the
+ * broadcast mechanism is used. On UP systems simply ignore it.
*/
if (disable_apic_timer) {
printk(KERN_INFO "Disabling APIC timer\n");
return;
}
- printk(KERN_INFO "Using local APIC timer interrupts.\n");
+ apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
+ "calibrating APIC timer ...\n");
+
if (calibrate_APIC_clock()) {
/* No broadcast on UP ! */
if (num_possible_cpus() > 1)
printk(KERN_WARNING "APIC timer registered as dummy,"
" due to nmi_watchdog=%d!\n", nmi_watchdog);
+ /* Setup the lapic or request the broadcast */
setup_APIC_timer();
}
irq_enter();
local_apic_timer_interrupt();
irq_exit();
+
set_irq_regs(old_regs);
}
apic_write(APIC_LVTPC, v | APIC_LVT_MASKED);
}
+ /* lets not touch this if we didn't frob it */
+#if defined(CONFIG_X86_MCE_P4THERMAL) || defined(X86_MCE_INTEL)
+ if (maxlvt >= 5) {
+ v = apic_read(APIC_LVTTHMR);
+ apic_write(APIC_LVTTHMR, v | APIC_LVT_MASKED);
+ }
+#endif
/*
* Clean APIC state for other OSs:
*/
apic_write(APIC_LVTERR, APIC_LVT_MASKED);
if (maxlvt >= 4)
apic_write(APIC_LVTPC, APIC_LVT_MASKED);
- apic_write(APIC_ESR, 0);
- apic_read(APIC_ESR);
+
+ /* Integrated APIC (!82489DX) ? */
+ if (lapic_is_integrated()) {
+ if (maxlvt > 3)
+ /* Clear ESR due to Pentium errata 3AP and 11AP */
+ apic_write(APIC_ESR, 0);
+ apic_read(APIC_ESR);
+ }
}
/**
value = apic_read(APIC_SPIV);
value &= ~APIC_SPIV_APIC_ENABLED;
apic_write(APIC_SPIV, value);
+
+#ifdef CONFIG_X86_32
+ /*
+ * When LAPIC was disabled by the BIOS and enabled by the kernel,
+ * restore the disabled state.
+ */
+ if (enabled_via_apicbase) {
+ unsigned int l, h;
+
+ rdmsr(MSR_IA32_APICBASE, l, h);
+ l &= ~MSR_IA32_APICBASE_ENABLE;
+ wrmsr(MSR_IA32_APICBASE, l, h);
+ }
+#endif
}
+/*
+ * If Linux enabled the LAPIC against the BIOS default disable it down before
+ * re-entering the BIOS on shutdown. Otherwise the BIOS may get confused and
+ * not power-off. Additionally clear all LVT entries before disable_local_APIC
+ * for the case where Linux didn't enable the LAPIC.
+ */
void lapic_shutdown(void)
{
unsigned long flags;
local_irq_save(flags);
- disable_local_APIC();
+#ifdef CONFIG_X86_32
+ if (!enabled_via_apicbase)
+ clear_local_APIC();
+ else
+#endif
+ disable_local_APIC();
+
local_irq_restore(flags);
}
*/
void __init sync_Arb_IDs(void)
{
- /* Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 */
- if (modern_apic())
+ /*
+ * Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not
+ * needed on AMD.
+ */
+ if (modern_apic() || boot_cpu_data.x86_vendor == X86_VENDOR_AMD)
return;
/*
apic_wait_icr_idle();
apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n");
- apic_write(APIC_ICR, APIC_DEST_ALLINC | APIC_INT_LEVELTRIG
- | APIC_DM_INIT);
+ apic_write(APIC_ICR, APIC_DEST_ALLINC |
+ APIC_INT_LEVELTRIG | APIC_DM_INIT);
}
/*
if (smp_found_config || !cpu_has_apic)
return;
- value = apic_read(APIC_LVR);
-
/*
* Do not trust the local APIC being empty at bootup.
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
value |= APIC_SPIV_APIC_ENABLED;
- value |= APIC_SPIV_FOCUS_DISABLED;
+
+#ifdef CONFIG_X86_32
+ /* This bit is reserved on P4/Xeon and should be cleared */
+ if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) &&
+ (boot_cpu_data.x86 == 15))
+ value &= ~APIC_SPIV_FOCUS_DISABLED;
+ else
+#endif
+ value |= APIC_SPIV_FOCUS_DISABLED;
value |= SPURIOUS_APIC_VECTOR;
apic_write(APIC_SPIV, value);
*/
apic_write(APIC_LVT0, APIC_DM_EXTINT);
value = APIC_DM_NMI;
+ if (!lapic_is_integrated()) /* 82489DX */
+ value |= APIC_LVT_LEVEL_TRIGGER;
apic_write(APIC_LVT1, value);
}
enable_apic_mode();
}
+/**
+ * disconnect_bsp_APIC - detach the APIC from the interrupt system
+ * @virt_wire_setup: indicates, whether virtual wire mode is selected
+ *
+ * Virtual wire mode is necessary to deliver legacy interrupts even when the
+ * APIC is disabled.
+ */
void disconnect_bsp_APIC(int virt_wire_setup)
{
/* Go back to Virtual Wire compatibility mode */
#ifdef CONFIG_PM
static struct {
- /* 'active' is true if the local APIC was enabled by us and
- not the BIOS; this signifies that we are also responsible
- for disabling it before entering apm/acpi suspend */
+ /*
+ * 'active' is true if the local APIC was enabled by us and
+ * not the BIOS; this signifies that we are also responsible
+ * for disabling it before entering apm/acpi suspend
+ */
int active;
/* r/w apic fields */
unsigned int apic_id;
apic_pm_state.apic_lvterr = apic_read(APIC_LVTERR);
apic_pm_state.apic_tmict = apic_read(APIC_TMICT);
apic_pm_state.apic_tdcr = apic_read(APIC_TDCR);
-#ifdef CONFIG_X86_MCE_INTEL
+#if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL)
if (maxlvt >= 5)
apic_pm_state.apic_thmr = apic_read(APIC_LVTTHMR);
#endif
+
local_irq_save(flags);
disable_local_APIC();
local_irq_restore(flags);
maxlvt = lapic_get_maxlvt();
local_irq_save(flags);
- if (!x2apic) {
+
+#ifdef CONFIG_X86_64
+ if (x2apic)
+ enable_x2apic();
+ else
+#endif
+ {
+ /*
+ * Make sure the APICBASE points to the right address
+ *
+ * FIXME! This will be wrong if we ever support suspend on
+ * SMP! We'll need to do this as part of the CPU restore!
+ */
rdmsr(MSR_IA32_APICBASE, l, h);
l &= ~MSR_IA32_APICBASE_BASE;
l |= MSR_IA32_APICBASE_ENABLE | mp_lapic_addr;
wrmsr(MSR_IA32_APICBASE, l, h);
- } else
- enable_x2apic();
+ }
apic_write(APIC_LVTERR, ERROR_APIC_VECTOR | APIC_LVT_MASKED);
apic_write(APIC_ID, apic_pm_state.apic_id);
apic_write(APIC_SPIV, apic_pm_state.apic_spiv);
apic_write(APIC_LVT0, apic_pm_state.apic_lvt0);
apic_write(APIC_LVT1, apic_pm_state.apic_lvt1);
-#ifdef CONFIG_X86_MCE_INTEL
+#if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL)
if (maxlvt >= 5)
apic_write(APIC_LVTTHMR, apic_pm_state.apic_thmr);
#endif
apic_write(APIC_LVTERR, apic_pm_state.apic_lvterr);
apic_write(APIC_ESR, 0);
apic_read(APIC_ESR);
+
local_irq_restore(flags);
+
return 0;
}
+/*
+ * This device has no shutdown method - fully functioning local APICs
+ * are needed on every CPU up until machine_halt/restart/poweroff.
+ */
+
static struct sysdev_class lapic_sysclass = {
.name = "lapic",
.resume = lapic_resume,
static __init int setup_disableapic(char *str)
{
disable_apic = 1;
- clear_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
+ setup_clear_cpu_cap(X86_FEATURE_APIC);
return 0;
}
early_param("disableapic", setup_disableapic);
}
early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok);
-static __init int setup_noapictimer(char *str)
+static int __init parse_disable_apic_timer(char *arg)
{
- if (str[0] != ' ' && str[0] != 0)
- return 0;
disable_apic_timer = 1;
- return 1;
+ return 0;
+}
+early_param("noapictimer", parse_disable_apic_timer);
+
+static int __init parse_nolapic_timer(char *arg)
+{
+ disable_apic_timer = 1;
+ return 0;
}
-__setup("noapictimer", setup_noapictimer);
+early_param("nolapic_timer", parse_nolapic_timer);
static __init int setup_apicpmtimer(char *s)
{