#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
+#include <linux/dmi.h>
#define DRV_NAME "ata_piix"
#define DRV_VERSION "2.11"
RV = -3, /* reserved */
PIIX_AHCI_DEVICE = 6,
+
+ /* host->flags bits */
+ PIIX_HOST_BROKEN_SUSPEND = (1 << 24),
};
struct piix_map_db {
static int piix_init_one (struct pci_dev *pdev,
const struct pci_device_id *ent);
static void piix_pata_error_handler(struct ata_port *ap);
-static void piix_sata_error_handler(struct ata_port *ap);
static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev);
static int ich_pata_cable_detect(struct ata_port *ap);
+#ifdef CONFIG_PM
+static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
+static int piix_pci_device_resume(struct pci_dev *pdev);
+#endif
static unsigned int in_module_init = 1;
/* ICH7/7-R (i945, i975) UDMA 100*/
{ 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
{ 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* ICH8 Mobile PATA Controller */
+ { 0x8086, 0x2850, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
/* NOTE: The following PCI ids must be kept in sync with the
* list in drivers/pci/quirks.c.
.probe = piix_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
- .suspend = ata_pci_device_suspend,
- .resume = ata_pci_device_resume,
+ .suspend = piix_pci_device_suspend,
+ .resume = piix_pci_device_resume,
#endif
};
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = piix_sata_error_handler,
+ .error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = ata_interrupt,
*/
.map = {
/* PM PS SM SS MAP */
- { P0, P2, RV, RV }, /* 00b */
+ { P0, P2, NA, NA }, /* 00b */
{ IDE, IDE, P1, P3 }, /* 01b */
{ P0, P2, IDE, IDE }, /* 10b */
{ RV, RV, RV, RV },
.flags = PIIX_SATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
.flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
{ 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
{ 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
{ 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
+ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */
/* end marker */
{ 0, }
};
ata_std_postreset);
}
-static void piix_sata_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, NULL,
- ata_std_postreset);
-}
-
/**
* piix_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE enable */
+ /* PIO configuration clears DTE unconditionally. It will be
+ * programmed in set_dmamode which is guaranteed to be called
+ * after set_piomode if any DMA mode is available.
+ */
pci_read_config_word(dev, master_port, &master_data);
if (is_slave) {
+ /* clear TIME1|IE1|PPE1|DTE1 */
+ master_data &= 0xff0f;
/* Enable SITRE (seperate slave timing register) */
master_data |= 0x4000;
/* enable PPE1, IE1 and TIME1 as needed */
pci_read_config_byte(dev, slave_port, &slave_data);
slave_data &= (ap->port_no ? 0x0f : 0xf0);
/* Load the timing nibble for this slave */
- slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1])
+ << (ap->port_no ? 4 : 0);
} else {
- /* Master keeps the bits in a different format */
- master_data &= 0xccf8;
+ /* clear ISP|RCT|TIME0|IE0|PPE0|DTE0 */
+ master_data &= 0xccf0;
/* Enable PPE, IE and TIME as appropriate */
master_data |= control;
+ /* load ISP and RCT */
master_data |=
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
master_data |= control << 4;
pci_read_config_byte(dev, 0x44, &slave_data);
- slave_data &= (0x0F + 0xE1 * ap->port_no);
+ slave_data &= (ap->port_no ? 0x0f : 0xf0);
/* Load the matching timing */
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
pci_write_config_byte(dev, 0x44, slave_data);
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
}
- udma_enable &= ~(1 << devid);
- pci_write_config_word(dev, master_port, master_data);
+
+ if (ap->udma_mask) {
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, master_port, master_data);
+ }
}
/* Don't scribble on 0x48 if the controller does not support UDMA */
if (ap->udma_mask)
do_pata_set_dmamode(ap, adev, 1);
}
+#ifdef CONFIG_PM
+static struct dmi_system_id piix_broken_suspend_dmi_table[] = {
+ {
+ .ident = "TECRA M5",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
+ },
+ },
+ {
+ .ident = "Satellite U200",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U200"),
+ },
+ },
+ {
+ .ident = "Satellite U205",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
+ },
+ },
+ {
+ .ident = "Portege M500",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
+ },
+ },
+ { }
+};
+
+static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ unsigned long flags;
+ int rc = 0;
+
+ rc = ata_host_suspend(host, mesg);
+ if (rc)
+ return rc;
+
+ /* Some braindamaged ACPI suspend implementations expect the
+ * controller to be awake on entry; otherwise, it burns cpu
+ * cycles and power trying to do something to the sleeping
+ * beauty.
+ */
+ if (dmi_check_system(piix_broken_suspend_dmi_table) &&
+ mesg.event == PM_EVENT_SUSPEND) {
+ pci_save_state(pdev);
+
+ /* mark its power state as "unknown", since we don't
+ * know if e.g. the BIOS will change its device state
+ * when we suspend.
+ */
+ if (pdev->current_state == PCI_D0)
+ pdev->current_state = PCI_UNKNOWN;
+
+ /* tell resume that it's waking up from broken suspend */
+ spin_lock_irqsave(&host->lock, flags);
+ host->flags |= PIIX_HOST_BROKEN_SUSPEND;
+ spin_unlock_irqrestore(&host->lock, flags);
+ } else
+ ata_pci_device_do_suspend(pdev, mesg);
+
+ return 0;
+}
+
+static int piix_pci_device_resume(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ unsigned long flags;
+ int rc;
+
+ if (host->flags & PIIX_HOST_BROKEN_SUSPEND) {
+ spin_lock_irqsave(&host->lock, flags);
+ host->flags &= ~PIIX_HOST_BROKEN_SUSPEND;
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+
+ /* PCI device wasn't disabled during suspend. Use
+ * __pci_reenable_device() to avoid affecting the
+ * enable count.
+ */
+ rc = __pci_reenable_device(pdev);
+ if (rc)
+ dev_printk(KERN_ERR, &pdev->dev, "failed to enable "
+ "device after resume (%d)\n", rc);
+ } else
+ rc = ata_pci_device_do_resume(pdev);
+
+ if (rc == 0)
+ ata_host_resume(host);
+
+ return rc;
+}
+#endif
+
#define AHCI_PCI_BAR 5
#define AHCI_GLOBAL_CTL 0x04
#define AHCI_ENABLE (1 << 31)
{
struct pci_dev *pdev = NULL;
u16 cfg;
- u8 rev;
int no_piix_dma = 0;
while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
{
/* Look for 450NX PXB. Check for problem configurations
A PCI quirk checks bit 6 already */
- pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
pci_read_config_word(pdev, 0x41, &cfg);
/* Only on the original revision: IDE DMA can hang */
- if (rev == 0x00)
+ if (pdev->revision == 0x00)
no_piix_dma = 1;
/* On all revisions below 5 PXB bus lock must be disabled for IDE */
- else if (cfg & (1<<14) && rev < 5)
+ else if (cfg & (1<<14) && pdev->revision < 5)
no_piix_dma = 2;
}
if (no_piix_dma)
projects / linux-2.6-omap-h63xx.git / blobdiff