* Omit those entries for boards you don't have installed.
*
* TODO
- * Hotplug
* Merge testing
* 64-bit verification
*/
#include <linux/module.h>
+#include <linux/firmware.h>
#include <linux/kernel.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/sched.h>
#include <linux/serial.h>
#include <linux/mm.h>
-#include <linux/miscdevice.h>
#include <linux/interrupt.h>
#include <linux/timer.h>
#include <linux/delay.h>
#define isicom_paranoia_check(a, b, c) 0
#endif
+static int isicom_probe(struct pci_dev *, const struct pci_device_id *);
+static void __devexit isicom_remove(struct pci_dev *);
+
static struct pci_device_id isicom_pci_tbl[] = {
- { VENDOR_ID, 0x2028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2051, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2052, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2053, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2054, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2055, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2056, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2057, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { PCI_DEVICE(VENDOR_ID, 0x2028) },
+ { PCI_DEVICE(VENDOR_ID, 0x2051) },
+ { PCI_DEVICE(VENDOR_ID, 0x2052) },
+ { PCI_DEVICE(VENDOR_ID, 0x2053) },
+ { PCI_DEVICE(VENDOR_ID, 0x2054) },
+ { PCI_DEVICE(VENDOR_ID, 0x2055) },
+ { PCI_DEVICE(VENDOR_ID, 0x2056) },
+ { PCI_DEVICE(VENDOR_ID, 0x2057) },
+ { PCI_DEVICE(VENDOR_ID, 0x2058) },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, isicom_pci_tbl);
+static struct pci_driver isicom_driver = {
+ .name = "isicom",
+ .id_table = isicom_pci_tbl,
+ .probe = isicom_probe,
+ .remove = __devexit_p(isicom_remove)
+};
+
static int prev_card = 3; /* start servicing isi_card[0] */
static struct tty_driver *isicom_normal;
static struct timer_list tx;
static char re_schedule = 1;
-static int ISILoad_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long arg);
-
static void isicom_tx(unsigned long _data);
static void isicom_start(struct tty_struct *tty);
-static unsigned char *tmp_buf;
-
/* baud index mappings from linux defns to isi */
static signed char linuxb_to_isib[] = {
unsigned char irq;
unsigned char port_count;
unsigned short status;
- unsigned short port_status; /* each bit represents a single port */
+ unsigned short port_status; /* each bit for each port */
unsigned short shift_count;
struct isi_port * ports;
signed char count;
udelay(1000); /* 1ms */
}
}
- printk(KERN_WARNING "ISICOM: Failed to lock Card (0x%lx)\n", card->base);
- return 0; /* Failed to aquire the card! */
+ printk(KERN_WARNING "ISICOM: Failed to lock Card (0x%lx)\n",
+ card->base);
+
+ return 0; /* Failed to acquire the card! */
}
static int lock_card_at_interrupt(struct isi_board *card)
spin_unlock_irqrestore(&card->card_lock, card->flags);
}
/* Failing in interrupt is an acceptable event */
- return 0; /* Failed to aquire the card! */
+ return 0; /* Failed to acquire the card! */
}
static void unlock_card(struct isi_board *card)
unlock_card(card);
}
-
-/*
- * Firmware loader driver specific routines. This needs to mostly die
- * and be replaced with request_firmware.
- */
-
-static struct file_operations ISILoad_fops = {
- .owner = THIS_MODULE,
- .ioctl = ISILoad_ioctl,
-};
-
-static struct miscdevice isiloader_device = {
- ISILOAD_MISC_MINOR, "isictl", &ISILoad_fops
-};
-
-
-static inline int WaitTillCardIsFree(unsigned long base)
-{
- unsigned long count=0;
- while( (!(inw(base+0xe) & 0x1)) && (count++ < 6000000));
- if (inw(base+0xe)&0x1)
- return 0;
- else
- return 1;
-}
-
-static int ISILoad_ioctl(struct inode *inode, struct file *filp,
- unsigned int cmd, unsigned long arg)
-{
- unsigned int card, i, j, signature, status, portcount = 0;
- unsigned long t, base;
- u16 word_count;
- bin_frame frame;
- void __user *argp = (void __user *)arg;
- /* exec_record exec_rec; */
-
- if (get_user(card, (int __user *)argp))
- return -EFAULT;
-
- if (card < 0 || card >= BOARD_COUNT)
- return -ENXIO;
-
- base=isi_card[card].base;
-
- if (base==0)
- return -ENXIO; /* disabled or not used */
-
- switch(cmd) {
- case MIOCTL_RESET_CARD:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
- printk(KERN_DEBUG "ISILoad:Resetting Card%d at 0x%lx ",card+1,base);
-
- inw(base+0x8);
-
- for (t=jiffies+HZ/100;time_before(jiffies, t););
-
- outw(0,base+0x8); /* Reset */
-
- for (j=1;j<=3;j++) {
- for (t=jiffies+HZ;time_before(jiffies, t););
- printk(".");
- }
- signature=(inw(base+0x4)) & 0xff;
- if (isi_card[card].isa) {
-
- if (!(inw(base+0xe) & 0x1) || (inw(base+0x2))) {
-#ifdef ISICOM_DEBUG
- printk("\nbase+0x2=0x%x , base+0xe=0x%x",inw(base+0x2),inw(base+0xe));
-#endif
- printk("\nISILoad:ISA Card%d reset failure (Possible bad I/O Port Address 0x%lx).\n",card+1,base);
- return -EIO;
- }
- }
- else {
- portcount = inw(base+0x2);
- if (!(inw(base+0xe) & 0x1) || ((portcount!=0) && (portcount!=4) && (portcount!=8))) {
-#ifdef ISICOM_DEBUG
- printk("\nbase+0x2=0x%x , base+0xe=0x%x",inw(base+0x2),inw(base+0xe));
-#endif
- printk("\nISILoad:PCI Card%d reset failure (Possible bad I/O Port Address 0x%lx).\n",card+1,base);
- return -EIO;
- }
- }
- switch(signature) {
- case 0xa5:
- case 0xbb:
- case 0xdd:
- if (isi_card[card].isa)
- isi_card[card].port_count = 8;
- else {
- if (portcount == 4)
- isi_card[card].port_count = 4;
- else
- isi_card[card].port_count = 8;
- }
- isi_card[card].shift_count = 12;
- break;
-
- case 0xcc: isi_card[card].port_count = 16;
- isi_card[card].shift_count = 11;
- break;
-
- default: printk("ISILoad:Card%d reset failure (Possible bad I/O Port Address 0x%lx).\n",card+1,base);
-#ifdef ISICOM_DEBUG
- printk("Sig=0x%x\n",signature);
-#endif
- return -EIO;
- }
- printk("-Done\n");
- return put_user(signature,(unsigned __user *)argp);
-
- case MIOCTL_LOAD_FIRMWARE:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- if (copy_from_user(&frame, argp, sizeof(bin_frame)))
- return -EFAULT;
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- outw(0xf0,base); /* start upload sequence */
- outw(0x00,base);
- outw((frame.addr), base); /* lsb of adderess */
-
- word_count=(frame.count >> 1) + frame.count % 2;
- outw(word_count, base);
- InterruptTheCard(base);
-
- for (i=0;i<=0x2f;i++); /* a wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_WARNING "ISILoad:Card%d rejected load header:\nAddress:0x%x \nCount:0x%x \nStatus:0x%x \n",
- card+1, frame.addr, frame.count, status);
- return -EIO;
- }
- outsw(base, (void *) frame.bin_data, word_count);
-
- InterruptTheCard(base);
-
- for (i=0;i<=0x0f;i++); /* another wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_ERR "ISILoad:Card%d got out of sync.Card Status:0x%x\n",card+1, status);
- return -EIO;
- }
- return 0;
-
- case MIOCTL_READ_FIRMWARE:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- if (copy_from_user(&frame, argp, sizeof(bin_header)))
- return -EFAULT;
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- outw(0xf1,base); /* start download sequence */
- outw(0x00,base);
- outw((frame.addr), base); /* lsb of adderess */
-
- word_count=(frame.count >> 1) + frame.count % 2;
- outw(word_count+1, base);
- InterruptTheCard(base);
-
- for (i=0;i<=0xf;i++); /* a wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_WARNING "ISILoad:Card%d rejected verify header:\nAddress:0x%x \nCount:0x%x \nStatus:0x%x \n",
- card+1, frame.addr, frame.count, status);
- return -EIO;
- }
-
- inw(base);
- insw(base, frame.bin_data, word_count);
- InterruptTheCard(base);
-
- for (i=0;i<=0x0f;i++); /* another wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_ERR "ISILoad:Card%d verify got out of sync.Card Status:0x%x\n",card+1, status);
- return -EIO;
- }
-
- if (copy_to_user(argp, &frame, sizeof(bin_frame)))
- return -EFAULT;
- return 0;
-
- case MIOCTL_XFER_CTRL:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- outw(0xf2, base);
- outw(0x800, base);
- outw(0x0, base);
- outw(0x0, base);
- InterruptTheCard(base);
- outw(0x0, base+0x4); /* for ISI4608 cards */
-
- isi_card[card].status |= FIRMWARE_LOADED;
- return 0;
-
- default:
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISILoad: Received Ioctl cmd 0x%x.\n", cmd);
-#endif
- return -ENOIOCTLCMD;
- }
-}
-
-
/*
* ISICOM Driver specific routines ...
*
residue = NO;
wrd = 0;
while (1) {
- cnt = min_t(int, txcount, (SERIAL_XMIT_SIZE - port->xmit_tail));
+ cnt = min_t(int, txcount, (SERIAL_XMIT_SIZE
+ - port->xmit_tail));
if (residue == YES) {
residue = NO;
if (cnt > 0) {
- wrd |= (port->xmit_buf[port->xmit_tail] << 8);
- port->xmit_tail = (port->xmit_tail + 1) & (SERIAL_XMIT_SIZE - 1);
+ wrd |= (port->xmit_buf[port->xmit_tail]
+ << 8);
+ port->xmit_tail = (port->xmit_tail + 1)
+ & (SERIAL_XMIT_SIZE - 1);
port->xmit_cnt--;
txcount--;
cnt--;
outw(wrd, base);
- }
- else {
+ } else {
outw(wrd, base);
break;
}
}
if (cnt <= 0) break;
word_count = cnt >> 1;
- outsw(base, port->xmit_buf+port->xmit_tail, word_count);
- port->xmit_tail = (port->xmit_tail + (word_count << 1)) &
- (SERIAL_XMIT_SIZE - 1);
+ outsw(base, port->xmit_buf+port->xmit_tail,word_count);
+ port->xmit_tail = (port->xmit_tail
+ + (word_count << 1)) & (SERIAL_XMIT_SIZE - 1);
txcount -= (word_count << 1);
port->xmit_cnt -= (word_count << 1);
if (cnt & 0x0001) {
residue = YES;
wrd = port->xmit_buf[port->xmit_tail];
- port->xmit_tail = (port->xmit_tail + 1) & (SERIAL_XMIT_SIZE - 1);
+ port->xmit_tail = (port->xmit_tail + 1)
+ & (SERIAL_XMIT_SIZE - 1);
port->xmit_cnt--;
txcount--;
}
byte_count = header & 0xff;
if (channel + 1 > card->port_count) {
- printk(KERN_WARNING "ISICOM: isicom_interrupt(0x%lx): %d(channel) > port_count.\n",
- base, channel+1);
+ printk(KERN_WARNING "ISICOM: isicom_interrupt(0x%lx): "
+ "%d(channel) > port_count.\n", base, channel+1);
if (card->isa)
ClearInterrupt(base);
else
header = inw(base);
switch(header & 0xff) {
case 0: /* Change in EIA signals */
-
if (port->flags & ASYNC_CHECK_CD) {
if (port->status & ISI_DCD) {
if (!(header & ISI_DCD)) {
/* Carrier has been lost */
- pr_dbg("interrupt: DCD->low.\n");
+ pr_dbg("interrupt: DCD->low.\n"
+ );
port->status &= ~ISI_DCD;
schedule_work(&port->hangup_tq);
}
+ } else if (header & ISI_DCD) {
+ /* Carrier has been detected */
+ pr_dbg("interrupt: DCD->high.\n");
+ port->status |= ISI_DCD;
+ wake_up_interruptible(&port->open_wait);
}
- else {
- if (header & ISI_DCD) {
- /* Carrier has been detected */
- pr_dbg("interrupt: DCD->high.\n");
- port->status |= ISI_DCD;
- wake_up_interruptible(&port->open_wait);
- }
- }
- }
- else {
+ } else {
if (header & ISI_DCD)
port->status |= ISI_DCD;
else
if (header & ISI_CTS) {
port->tty->hw_stopped = 0;
/* start tx ing */
- port->status |= (ISI_TXOK | ISI_CTS);
+ port->status |= (ISI_TXOK
+ | ISI_CTS);
schedule_work(&port->bh_tqueue);
}
+ } else if (!(header & ISI_CTS)) {
+ port->tty->hw_stopped = 1;
+ /* stop tx ing */
+ port->status &= ~(ISI_TXOK | ISI_CTS);
}
- else {
- if (!(header & ISI_CTS)) {
- port->tty->hw_stopped = 1;
- /* stop tx ing */
- port->status &= ~(ISI_TXOK | ISI_CTS);
- }
- }
- }
- else {
+ } else {
if (header & ISI_CTS)
port->status |= ISI_CTS;
else
break;
- case 1: /* Received Break !!! */
+ case 1: /* Received Break !!! */
tty_insert_flip_char(tty, 0, TTY_BREAK);
if (port->flags & ASYNC_SAK)
do_SAK(tty);
pr_dbg("Intr: Unknown code in status packet.\n");
break;
}
- }
- else { /* Data Packet */
+ } else { /* Data Packet */
count = tty_prepare_flip_string(tty, &rp, byte_count & ~1);
pr_dbg("Intr: Can rx %d of %d bytes.\n", count, byte_count);
insw(base, rp, word_count);
byte_count -= (word_count << 1);
if (count & 0x0001) {
- tty_insert_flip_char(tty, inw(base) & 0xff, TTY_NORMAL);
+ tty_insert_flip_char(tty, inw(base) & 0xff,
+ TTY_NORMAL);
byte_count -= 2;
}
if (byte_count > 0) {
ClearInterrupt(base);
else
outw(0x0000, base+0x04); /* enable interrupts */
+
return IRQ_HANDLED;
}
return 0;
}
-static int block_til_ready(struct tty_struct *tty, struct file *filp, struct isi_port *port)
+static int block_til_ready(struct tty_struct *tty, struct file *filp,
+ struct isi_port *port)
{
struct isi_board *card = port->card;
int do_clocal = 0, retval;
/* if non-blocking mode is set ... */
- if ((filp->f_flags & O_NONBLOCK) || (tty->flags & (1 << TTY_IO_ERROR))) {
+ if ((filp->f_flags & O_NONBLOCK) ||
+ (tty->flags & (1 << TTY_IO_ERROR))) {
pr_dbg("block_til_ready: non-block mode.\n");
port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
card->count = 0;
}
- /* last port was closed , shutdown that boad too */
+ /* last port was closed, shutdown that boad too */
if (C_HUPCL(tty)) {
if (!card->count)
isicom_shutdown_board(card);
}
if (tty->count == 1 && port->count != 1) {
- printk(KERN_WARNING "ISICOM:(0x%lx) isicom_close: bad port count"
- "tty->count = 1 port count = %d.\n",
+ printk(KERN_WARNING "ISICOM:(0x%lx) isicom_close: bad port "
+ "count tty->count = 1 port count = %d.\n",
card->base, port->count);
port->count = 1;
}
if (--port->count < 0) {
- printk(KERN_WARNING "ISICOM:(0x%lx) isicom_close: bad port count for"
- "channel%d = %d", card->base, port->channel,
+ printk(KERN_WARNING "ISICOM:(0x%lx) isicom_close: bad port "
+ "count for channel%d = %d", card->base, port->channel,
port->count);
port->count = 0;
}
spin_unlock_irqrestore(&card->card_lock, flags);
if (port->close_delay) {
pr_dbg("scheduling until time out.\n");
- msleep_interruptible(jiffies_to_msecs(port->close_delay));
+ msleep_interruptible(
+ jiffies_to_msecs(port->close_delay));
}
spin_lock_irqsave(&card->card_lock, flags);
wake_up_interruptible(&port->open_wait);
if (isicom_paranoia_check(port, tty->name, "isicom_write"))
return 0;
- if (!tty || !port->xmit_buf || !tmp_buf)
+ if (!port->xmit_buf)
return 0;
spin_lock_irqsave(&card->card_lock, flags);
while(1) {
- cnt = min_t(int, count, min(SERIAL_XMIT_SIZE - port->xmit_cnt - 1,
- SERIAL_XMIT_SIZE - port->xmit_head));
+ cnt = min_t(int, count, min(SERIAL_XMIT_SIZE - port->xmit_cnt
+ - 1, SERIAL_XMIT_SIZE - port->xmit_head));
if (cnt <= 0)
break;
memcpy(port->xmit_buf + port->xmit_head, buf, cnt);
- port->xmit_head = (port->xmit_head + cnt) & (SERIAL_XMIT_SIZE - 1);
+ port->xmit_head = (port->xmit_head + cnt) & (SERIAL_XMIT_SIZE
+ - 1);
port->xmit_cnt += cnt;
buf += cnt;
count -= cnt;
if (isicom_paranoia_check(port, tty->name, "isicom_put_char"))
return;
- if (!tty || !port->xmit_buf)
+ if (!port->xmit_buf)
return;
spin_lock_irqsave(&card->card_lock, flags);
if (isicom_paranoia_check(port, tty->name, "isicom_flush_chars"))
return;
- if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || !port->xmit_buf)
+ if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
+ !port->xmit_buf)
return;
/* this tells the transmitter to consider this port for
}
/* ioctl et all */
-static inline void isicom_send_break(struct isi_port *port, unsigned long length)
+static inline void isicom_send_break(struct isi_port *port,
+ unsigned long length)
{
struct isi_board *card = port->card;
unsigned long base = card->base;
return 0;
case TIOCGSOFTCAR:
- return put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *)argp);
+ return put_user(C_CLOCAL(tty) ? 1 : 0,
+ (unsigned long __user *)argp);
case TIOCSSOFTCAR:
if (get_user(arg, (unsigned long __user *) argp))
tty_wakeup(tty);
}
+/*
+ * Driver init and deinit functions
+ */
-static int __devinit register_ioregion(void)
+static int __devinit isicom_register_ioregion(struct pci_dev *pdev,
+ const unsigned int index)
{
- int count, done=0;
- for (count=0; count < BOARD_COUNT; count++ ) {
- if (isi_card[count].base)
- if (!request_region(isi_card[count].base,16,ISICOM_NAME)) {
- printk(KERN_DEBUG "ISICOM: I/O Region 0x%lx-0x%lx is busy. Card%d will be disabled.\n",
- isi_card[count].base,isi_card[count].base+15,count+1);
- isi_card[count].base=0;
- done++;
- }
- }
- return done;
+ struct isi_board *board = pci_get_drvdata(pdev);
+
+ if (!board->base)
+ return -EINVAL;
+
+ if (!request_region(board->base, 16, ISICOM_NAME)) {
+ dev_dbg(&pdev->dev, "I/O Region 0x%lx-0x%lx is busy. Card%d "
+ "will be disabled.\n", board->base, board->base + 15,
+ index + 1);
+ return -EBUSY;
+ }
+
+ return 0;
}
-static void unregister_ioregion(void)
+static void isicom_unregister_ioregion(struct pci_dev *pdev)
{
- int count;
- for (count=0; count < BOARD_COUNT; count++ )
- if (isi_card[count].base) {
- release_region(isi_card[count].base,16);
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: I/O Region 0x%lx-0x%lx released for Card%d.\n",isi_card[count].base,isi_card[count].base+15,count+1);
-#endif
- }
+ struct isi_board *board = pci_get_drvdata(pdev);
+
+ if (!board->base)
+ return;
+
+ release_region(board->base, 16);
+ dev_dbg(&pdev->dev, "I/O Region 0x%lx-0x%lx released.\n",
+ board->base, board->base + 15);
+ board->base = 0;
}
static struct tty_operations isicom_ops = {
isicom_normal->owner = THIS_MODULE;
isicom_normal->name = "ttyM";
- isicom_normal->devfs_name = "isicom/";
isicom_normal->major = ISICOM_NMAJOR;
isicom_normal->minor_start = 0;
isicom_normal->type = TTY_DRIVER_TYPE_SERIAL;
put_tty_driver(isicom_normal);
}
-static int __devinit register_isr(void)
+static int __devinit isicom_register_isr(struct pci_dev *pdev,
+ const unsigned int index)
{
- int count, done=0;
- unsigned long irqflags;
-
- for (count=0; count < BOARD_COUNT; count++ ) {
- if (isi_card[count].base) {
- irqflags = (isi_card[count].isa == YES) ?
- SA_INTERRUPT :
- (SA_INTERRUPT | SA_SHIRQ);
-
- if (request_irq(isi_card[count].irq,
- isicom_interrupt,
- irqflags,
- ISICOM_NAME, &isi_card[count])) {
-
- printk(KERN_WARNING "ISICOM: Could not"
- " install handler at Irq %d."
- " Card%d will be disabled.\n",
- isi_card[count].irq, count+1);
-
- release_region(isi_card[count].base,16);
- isi_card[count].base=0;
- }
- else
- done++;
+ struct isi_board *board = pci_get_drvdata(pdev);
+ unsigned long irqflags = IRQF_DISABLED;
+ int retval = -EINVAL;
+
+ if (!board->base)
+ goto end;
+
+ if (board->isa == NO)
+ irqflags |= IRQF_SHARED;
+
+ retval = request_irq(board->irq, isicom_interrupt, irqflags,
+ ISICOM_NAME, board);
+ if (retval < 0)
+ dev_warn(&pdev->dev, "Could not install handler at Irq %d. "
+ "Card%d will be disabled.\n", board->irq, index + 1);
+ else
+ retval = 0;
+end:
+ return retval;
+}
+
+static int __devinit reset_card(struct pci_dev *pdev,
+ const unsigned int card, unsigned int *signature)
+{
+ struct isi_board *board = pci_get_drvdata(pdev);
+ unsigned long base = board->base;
+ unsigned int portcount = 0;
+ int retval = 0;
+
+ dev_dbg(&pdev->dev, "ISILoad:Resetting Card%d at 0x%lx\n", card + 1,
+ base);
+
+ inw(base + 0x8);
+
+ mdelay(10);
+
+ outw(0, base + 0x8); /* Reset */
+
+ msleep(3000);
+
+ *signature = inw(base + 0x4) & 0xff;
+
+ if (board->isa == YES) {
+ if (!(inw(base + 0xe) & 0x1) || (inw(base + 0x2))) {
+ dev_dbg(&pdev->dev, "base+0x2=0x%lx, base+0xe=0x%lx\n",
+ inw(base + 0x2), inw(base + 0xe));
+ dev_err(&pdev->dev, "ISILoad:ISA Card%d reset failure "
+ "(Possible bad I/O Port Address 0x%lx).\n",
+ card + 1, base);
+ retval = -EIO;
+ goto end;
+ }
+ } else {
+ portcount = inw(base + 0x2);
+ if (!(inw(base + 0xe) & 0x1) || ((portcount != 0) &&
+ (portcount != 4) && (portcount != 8))) {
+ dev_dbg(&pdev->dev, "base+0x2=0x%lx, base+0xe=0x%lx\n",
+ inw(base + 0x2), inw(base + 0xe));
+ dev_err(&pdev->dev, "ISILoad:PCI Card%d reset failure "
+ "(Possible bad I/O Port Address 0x%lx).\n",
+ card + 1, base);
+ retval = -EIO;
+ goto end;
}
}
- return done;
+
+ switch (*signature) {
+ case 0xa5:
+ case 0xbb:
+ case 0xdd:
+ board->port_count = (board->isa == NO && portcount == 4) ? 4 :
+ 8;
+ board->shift_count = 12;
+ break;
+ case 0xcc:
+ board->port_count = 16;
+ board->shift_count = 11;
+ break;
+ default:
+ dev_warn(&pdev->dev, "ISILoad:Card%d reset failure (Possible "
+ "bad I/O Port Address 0x%lx).\n", card + 1, base);
+ dev_dbg(&pdev->dev, "Sig=0x%lx\n", signature);
+ retval = -EIO;
+ }
+ dev_info(&pdev->dev, "-Done\n");
+
+end:
+ return retval;
}
-static void __exit unregister_isr(void)
+static inline int WaitTillCardIsFree(u16 base)
{
- int count;
+ unsigned long count = 0;
- for (count=0; count < BOARD_COUNT; count++ ) {
- if (isi_card[count].base)
- free_irq(isi_card[count].irq, &isi_card[count]);
- }
+ while (!(inw(base + 0xe) & 0x1) && count++ < 100)
+ msleep(5);
+
+ return !(inw(base + 0xe) & 0x1);
}
-static int __devinit isicom_init(void)
+static int __devinit load_firmware(struct pci_dev *pdev,
+ const unsigned int index, const unsigned int signature)
{
- int card, channel, base;
- struct isi_port *port;
- unsigned long page;
+ struct isi_board *board = pci_get_drvdata(pdev);
+ const struct firmware *fw;
+ unsigned long base = board->base;
+ unsigned int a;
+ u16 word_count, status;
+ int retval = -EIO;
+ char *name;
+ u8 *data;
+
+ struct stframe {
+ u16 addr;
+ u16 count;
+ u8 data[0];
+ } *frame;
+
+ switch (signature) {
+ case 0xa5:
+ name = "isi608.bin";
+ break;
+ case 0xbb:
+ name = "isi608em.bin";
+ break;
+ case 0xcc:
+ name = "isi616em.bin";
+ break;
+ case 0xdd:
+ name = "isi4608.bin";
+ break;
+ case 0xee:
+ name = "isi4616.bin";
+ break;
+ default:
+ dev_err(&pdev->dev, "Unknown signature.\n");
+ goto end;
+ }
- if (!tmp_buf) {
- page = get_zeroed_page(GFP_KERNEL);
- if (!page) {
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: Couldn't allocate page for tmp_buf.\n");
-#else
- printk(KERN_ERR "ISICOM: Not enough memory...\n");
-#endif
- return 0;
+ retval = request_firmware(&fw, name, &pdev->dev);
+ if (retval)
+ goto end;
+
+ for (frame = (struct stframe *)fw->data;
+ frame < (struct stframe *)(fw->data + fw->size);
+ frame++) {
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ outw(0xf0, base); /* start upload sequence */
+ outw(0x00, base);
+ outw(frame->addr, base); /* lsb of address */
+
+ word_count = frame->count / 2 + frame->count % 2;
+ outw(word_count, base);
+ InterruptTheCard(base);
+
+ udelay(100); /* 0x2f */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ dev_warn(&pdev->dev, "Card%d rejected load header:\n"
+ "Address:0x%x\nCount:0x%x\nStatus:0x%x\n",
+ index + 1, frame->addr, frame->count, status);
+ goto errrelfw;
}
- tmp_buf = (unsigned char *) page;
- }
+ outsw(base, frame->data, word_count);
- if (!register_ioregion())
- {
- printk(KERN_ERR "ISICOM: All required I/O space found busy.\n");
- free_page((unsigned long)tmp_buf);
- return 0;
- }
- if (isicom_register_tty_driver())
- {
- unregister_ioregion();
- free_page((unsigned long)tmp_buf);
- return 0;
- }
- if (!register_isr())
- {
- isicom_unregister_tty_driver();
- /* ioports already uregistered in register_isr */
- free_page((unsigned long)tmp_buf);
- return 0;
- }
+ InterruptTheCard(base);
- memset(isi_ports, 0, sizeof(isi_ports));
- for (card = 0; card < BOARD_COUNT; card++) {
- port = &isi_ports[card * 16];
- isi_card[card].ports = port;
- spin_lock_init(&isi_card[card].card_lock);
- base = isi_card[card].base;
- for (channel = 0; channel < 16; channel++, port++) {
- port->magic = ISICOM_MAGIC;
- port->card = &isi_card[card];
- port->channel = channel;
- port->close_delay = 50 * HZ/100;
- port->closing_wait = 3000 * HZ/100;
- INIT_WORK(&port->hangup_tq, do_isicom_hangup, port);
- INIT_WORK(&port->bh_tqueue, isicom_bottomhalf, port);
- port->status = 0;
- init_waitqueue_head(&port->open_wait);
- init_waitqueue_head(&port->close_wait);
- /* . . . */
+ udelay(50); /* 0x0f */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ dev_err(&pdev->dev, "Card%d got out of sync.Card "
+ "Status:0x%x\n", index + 1, status);
+ goto errrelfw;
+ }
+ }
+
+ retval = -EIO;
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ outw(0xf2, base);
+ outw(0x800, base);
+ outw(0x0, base);
+ outw(0x0, base);
+ InterruptTheCard(base);
+ outw(0x0, base + 0x4); /* for ISI4608 cards */
+
+/* XXX: should we test it by reading it back and comparing with original like
+ * in load firmware package? */
+ for (frame = (struct stframe*)fw->data;
+ frame < (struct stframe*)(fw->data + fw->size);
+ frame++) {
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ outw(0xf1, base); /* start download sequence */
+ outw(0x00, base);
+ outw(frame->addr, base); /* lsb of address */
+
+ word_count = (frame->count >> 1) + frame->count % 2;
+ outw(word_count + 1, base);
+ InterruptTheCard(base);
+
+ udelay(50); /* 0xf */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ dev_warn(&pdev->dev, "Card%d rejected verify header:\n"
+ "Address:0x%x\nCount:0x%x\nStatus: 0x%x\n",
+ index + 1, frame->addr, frame->count, status);
+ goto errrelfw;
+ }
+
+ data = kmalloc(word_count * 2, GFP_KERNEL);
+ inw(base);
+ insw(base, data, word_count);
+ InterruptTheCard(base);
+
+ for (a = 0; a < frame->count; a++)
+ if (data[a] != frame->data[a]) {
+ kfree(data);
+ dev_err(&pdev->dev, "Card%d, firmware upload "
+ "failed\n", index + 1);
+ goto errrelfw;
+ }
+ kfree(data);
+
+ udelay(50); /* 0xf */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ dev_err(&pdev->dev, "Card%d verify got out of sync. "
+ "Card Status:0x%x\n", index + 1, status);
+ goto errrelfw;
}
}
- return 1;
+ board->status |= FIRMWARE_LOADED;
+ retval = 0;
+
+errrelfw:
+ release_firmware(fw);
+end:
+ return retval;
}
/*
* Insmod can set static symbols so keep these static
*/
-
static int io[4];
static int irq[4];
+static int card;
+
+static int __devinit isicom_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ unsigned int ioaddr, signature, index;
+ int retval = -EPERM;
+ u8 pciirq;
+ struct isi_board *board = NULL;
+
+ if (card >= BOARD_COUNT)
+ goto err;
+
+ ioaddr = pci_resource_start(pdev, 3);
+ /* i.e at offset 0x1c in the PCI configuration register space. */
+ pciirq = pdev->irq;
+ dev_info(&pdev->dev, "ISI PCI Card(Device ID 0x%x)\n", ent->device);
+
+ /* allot the first empty slot in the array */
+ for (index = 0; index < BOARD_COUNT; index++)
+ if (isi_card[index].base == 0) {
+ board = &isi_card[index];
+ break;
+ }
+
+ board->base = ioaddr;
+ board->irq = pciirq;
+ board->isa = NO;
+ card++;
+
+ pci_set_drvdata(pdev, board);
+
+ retval = isicom_register_ioregion(pdev, index);
+ if (retval < 0)
+ goto err;
+
+ retval = isicom_register_isr(pdev, index);
+ if (retval < 0)
+ goto errunrr;
+
+ retval = reset_card(pdev, index, &signature);
+ if (retval < 0)
+ goto errunri;
+
+ retval = load_firmware(pdev, index, signature);
+ if (retval < 0)
+ goto errunri;
+
+ return 0;
+
+errunri:
+ free_irq(board->irq, board);
+errunrr:
+ isicom_unregister_ioregion(pdev);
+err:
+ board->base = 0;
+ return retval;
+}
+
+static void __devexit isicom_remove(struct pci_dev *pdev)
+{
+ struct isi_board *board = pci_get_drvdata(pdev);
+
+ free_irq(board->irq, board);
+ isicom_unregister_ioregion(pdev);
+}
static int __devinit isicom_setup(void)
{
- struct pci_dev *dev = NULL;
- int retval, card, idx, count;
- unsigned char pciirq;
- unsigned int ioaddr;
+ int retval, idx, channel;
+ struct isi_port *port;
card = 0;
- for (idx=0; idx < BOARD_COUNT; idx++) {
- if (io[idx]) {
- isi_card[idx].base=io[idx];
- isi_card[idx].irq=irq[idx];
- isi_card[idx].isa=YES;
- card++;
- }
- else {
- isi_card[idx].base = 0;
- isi_card[idx].irq = 0;
- }
- }
-
- for (idx=0 ;idx < card; idx++) {
- if (!((isi_card[idx].irq==2)||(isi_card[idx].irq==3)||
- (isi_card[idx].irq==4)||(isi_card[idx].irq==5)||
- (isi_card[idx].irq==7)||(isi_card[idx].irq==10)||
- (isi_card[idx].irq==11)||(isi_card[idx].irq==12)||
- (isi_card[idx].irq==15))) {
-
- if (isi_card[idx].base) {
- printk(KERN_ERR "ISICOM: Irq %d unsupported. Disabling Card%d...\n",
- isi_card[idx].irq, idx+1);
- isi_card[idx].base=0;
- card--;
- }
- }
- }
+ memset(isi_ports, 0, sizeof(isi_ports));
- if (card < BOARD_COUNT) {
- for (idx=0; idx < DEVID_COUNT; idx++) {
- dev = NULL;
- for (;;){
- if (!(dev = pci_find_device(VENDOR_ID, isicom_pci_tbl[idx].device, dev)))
- break;
- if (card >= BOARD_COUNT)
- break;
+ for(idx = 0; idx < BOARD_COUNT; idx++) {
+ port = &isi_ports[idx * 16];
+ isi_card[idx].ports = port;
+ spin_lock_init(&isi_card[idx].card_lock);
+ for (channel = 0; channel < 16; channel++, port++) {
+ port->magic = ISICOM_MAGIC;
+ port->card = &isi_card[idx];
+ port->channel = channel;
+ port->close_delay = 50 * HZ/100;
+ port->closing_wait = 3000 * HZ/100;
+ INIT_WORK(&port->hangup_tq, do_isicom_hangup, port);
+ INIT_WORK(&port->bh_tqueue, isicom_bottomhalf, port);
+ port->status = 0;
+ init_waitqueue_head(&port->open_wait);
+ init_waitqueue_head(&port->close_wait);
+ /* . . . */
+ }
+ isi_card[idx].base = 0;
+ isi_card[idx].irq = 0;
- if (pci_enable_device(dev))
- break;
+ if (!io[idx])
+ continue;
- /* found a PCI ISI card! */
- ioaddr = pci_resource_start (dev, 3);
- /* i.e at offset 0x1c in the
- * PCI configuration register
- * space.
- */
- pciirq = dev->irq;
- printk(KERN_INFO "ISI PCI Card(Device ID 0x%x)\n", isicom_pci_tbl[idx].device);
- /*
- * allot the first empty slot in the array
- */
- for (count=0; count < BOARD_COUNT; count++) {
- if (isi_card[count].base == 0) {
- isi_card[count].base = ioaddr;
- isi_card[count].irq = pciirq;
- isi_card[count].isa = NO;
- card++;
- break;
- }
- }
- }
- if (card >= BOARD_COUNT) break;
- }
+ if (irq[idx] == 2 || irq[idx] == 3 || irq[idx] == 4 ||
+ irq[idx] == 5 || irq[idx] == 7 ||
+ irq[idx] == 10 || irq[idx] == 11 ||
+ irq[idx] == 12 || irq[idx] == 15) {
+ printk(KERN_ERR "ISICOM: ISA not supported yet.\n");
+ retval = -EINVAL;
+ goto error;
+ } else
+ printk(KERN_ERR "ISICOM: Irq %d unsupported. "
+ "Disabling Card%d...\n", irq[idx], idx + 1);
}
- if (!(isi_card[0].base || isi_card[1].base || isi_card[2].base || isi_card[3].base)) {
- printk(KERN_ERR "ISICOM: No valid card configuration. Driver cannot be initialized...\n");
- return -EIO;
- }
+ retval = isicom_register_tty_driver();
+ if (retval < 0)
+ goto error;
- retval = misc_register(&isiloader_device);
+ retval = pci_register_driver(&isicom_driver);
if (retval < 0) {
- printk(KERN_ERR "ISICOM: Unable to register firmware loader driver.\n");
- return retval;
- }
-
- if (!isicom_init()) {
- if (misc_deregister(&isiloader_device))
- printk(KERN_ERR "ISICOM: Unable to unregister Firmware Loader driver\n");
- return -EIO;
+ printk(KERN_ERR "ISICOM: Unable to register pci driver.\n");
+ goto errtty;
}
init_timer(&tx);
add_timer(&tx);
return 0;
+errtty:
+ isicom_unregister_tty_driver();
+error:
+ return retval;
}
static void __exit isicom_exit(void)
while (re_schedule != 2 && index++ < 100)
msleep(10);
- unregister_isr();
+ pci_unregister_driver(&isicom_driver);
isicom_unregister_tty_driver();
- unregister_ioregion();
- if (tmp_buf)
- free_page((unsigned long)tmp_buf);
- if (misc_deregister(&isiloader_device))
- printk(KERN_ERR "ISICOM: Unable to unregister Firmware Loader driver\n");
}
module_init(isicom_setup);