int address_high;
unsigned int workarounds;
unsigned int mgt_orb_timeout;
+ unsigned int max_payload;
int dont_block; /* counter for each logical unit */
int blocked; /* ditto */
dma_addr_t page_table_bus;
};
+#define SBP2_ROM_VALUE_WILDCARD ~0 /* match all */
+#define SBP2_ROM_VALUE_MISSING 0xff000000 /* not present in the unit dir. */
+
/*
* List of devices with known bugs.
*
* The firmware_revision field, masked with 0xffff00, is the best
* indicator for the type of bridge chip of a device. It yields a few
* false positives but this did not break correctly behaving devices
- * so far. We use ~0 as a wildcard, since the 24 bit values we get
- * from the config rom can never match that.
+ * so far.
*/
static const struct {
u32 firmware_revision;
},
/* Initio bridges, actually only needed for some older ones */ {
.firmware_revision = 0x000200,
- .model = ~0,
+ .model = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_INQUIRY_36,
},
/* PL-3507 bridge with Prolific firmware */ {
.firmware_revision = 0x012800,
- .model = ~0,
+ .model = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_POWER_CONDITION,
},
/* Symbios bridge */ {
.firmware_revision = 0xa0b800,
- .model = ~0,
+ .model = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_128K_MAX_TRANS,
},
/* Datafab MD2-FW2 with Symbios/LSILogic SYM13FW500 bridge */ {
.firmware_revision = 0x002600,
- .model = ~0,
+ .model = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_128K_MAX_TRANS,
},
-
/*
- * There are iPods (2nd gen, 3rd gen) with model_id == 0, but
- * these iPods do not feature the read_capacity bug according
- * to one report. Read_capacity behaviour as well as model_id
- * could change due to Apple-supplied firmware updates though.
+ * iPod 2nd generation: needs 128k max transfer size workaround
+ * iPod 3rd generation: needs fix capacity workaround
*/
-
- /* iPod 4th generation. */ {
+ {
+ .firmware_revision = 0x0a2700,
+ .model = 0x000000,
+ .workarounds = SBP2_WORKAROUND_128K_MAX_TRANS |
+ SBP2_WORKAROUND_FIX_CAPACITY,
+ },
+ /* iPod 4th generation */ {
.firmware_revision = 0x0a2700,
.model = 0x000021,
.workarounds = SBP2_WORKAROUND_FIX_CAPACITY,
continue;
if (sbp2_workarounds_table[i].model != model &&
- sbp2_workarounds_table[i].model != ~0)
+ sbp2_workarounds_table[i].model != SBP2_ROM_VALUE_WILDCARD)
continue;
w |= sbp2_workarounds_table[i].workarounds;
fw_device_get(device);
fw_unit_get(unit);
- /* Initialize to values that won't match anything in our table. */
- firmware_revision = 0xff000000;
- model = 0xff000000;
-
/* implicit directory ID */
tgt->directory_id = ((unit->directory - device->config_rom) * 4
+ CSR_CONFIG_ROM) & 0xffffff;
+ firmware_revision = SBP2_ROM_VALUE_MISSING;
+ model = SBP2_ROM_VALUE_MISSING;
+
if (sbp2_scan_unit_dir(tgt, unit->directory, &model,
&firmware_revision) < 0)
goto fail_tgt_put;
sbp2_init_workarounds(tgt, model, firmware_revision);
+ /*
+ * At S100 we can do 512 bytes per packet, at S200 1024 bytes,
+ * and so on up to 4096 bytes. The SBP-2 max_payload field
+ * specifies the max payload size as 2 ^ (max_payload + 2), so
+ * if we set this to max_speed + 7, we get the right value.
+ */
+ tgt->max_payload = min(device->max_speed + 7, 10U);
+ tgt->max_payload = min(tgt->max_payload, device->card->max_receive - 1);
+
/* Do the login in a workqueue so we can easily reschedule retries. */
list_for_each_entry(lu, &tgt->lu_list, link)
sbp2_queue_work(lu, DIV_ROUND_UP(HZ, 5));
.id_table = sbp2_id_table,
};
+static void sbp2_unmap_scatterlist(struct device *card_device,
+ struct sbp2_command_orb *orb)
+{
+ if (scsi_sg_count(orb->cmd))
+ dma_unmap_sg(card_device, scsi_sglist(orb->cmd),
+ scsi_sg_count(orb->cmd),
+ orb->cmd->sc_data_direction);
+
+ if (orb->request.misc & cpu_to_be32(COMMAND_ORB_PAGE_TABLE_PRESENT))
+ dma_unmap_single(card_device, orb->page_table_bus,
+ sizeof(orb->page_table), DMA_TO_DEVICE);
+}
+
static unsigned int
sbp2_status_to_sense_data(u8 *sbp2_status, u8 *sense_data)
{
dma_unmap_single(device->card->device, orb->base.request_bus,
sizeof(orb->request), DMA_TO_DEVICE);
-
- if (scsi_sg_count(orb->cmd) > 0)
- dma_unmap_sg(device->card->device, scsi_sglist(orb->cmd),
- scsi_sg_count(orb->cmd),
- orb->cmd->sc_data_direction);
-
- if (orb->page_table_bus != 0)
- dma_unmap_single(device->card->device, orb->page_table_bus,
- sizeof(orb->page_table), DMA_TO_DEVICE);
+ sbp2_unmap_scatterlist(device->card->device, orb);
orb->cmd->result = result;
orb->done(orb->cmd);
struct sbp2_logical_unit *lu = cmd->device->hostdata;
struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
struct sbp2_command_orb *orb;
- unsigned int max_payload;
int generation, retval = SCSI_MLQUEUE_HOST_BUSY;
/*
orb->done = done;
orb->cmd = cmd;
- orb->request.next.high = cpu_to_be32(SBP2_ORB_NULL);
- /*
- * At speed 100 we can do 512 bytes per packet, at speed 200,
- * 1024 bytes per packet etc. The SBP-2 max_payload field
- * specifies the max payload size as 2 ^ (max_payload + 2), so
- * if we set this to max_speed + 7, we get the right value.
- */
- max_payload = min(device->max_speed + 7,
- device->card->max_receive - 1);
+ orb->request.next.high = cpu_to_be32(SBP2_ORB_NULL);
orb->request.misc = cpu_to_be32(
- COMMAND_ORB_MAX_PAYLOAD(max_payload) |
+ COMMAND_ORB_MAX_PAYLOAD(lu->tgt->max_payload) |
COMMAND_ORB_SPEED(device->max_speed) |
COMMAND_ORB_NOTIFY);
orb->base.request_bus =
dma_map_single(device->card->device, &orb->request,
sizeof(orb->request), DMA_TO_DEVICE);
- if (dma_mapping_error(device->card->device, orb->base.request_bus))
+ if (dma_mapping_error(device->card->device, orb->base.request_bus)) {
+ sbp2_unmap_scatterlist(device->card->device, orb);
goto out;
+ }
sbp2_send_orb(&orb->base, lu, lu->tgt->node_id, generation,
lu->command_block_agent_address + SBP2_ORB_POINTER);
projects / linux-2.6-omap-h63xx.git / blobdiff