/*
- * linux/drivers/ide/pci/cmd64x.c Version 1.53 Dec 24, 2007
- *
* cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
* Due to massive hardware bugs, UltraDMA is only supported
* on the 646U2 and not on the 646U.
#include <linux/module.h>
#include <linux/types.h>
#include <linux/pci.h>
-#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
*/
static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_time)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- int clock_time = 1000 / system_bus_clock();
+ struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+ int clock_time = 1000 / (ide_pci_clk ? ide_pci_clk : 33);
u8 cycle_count, active_count, recovery_count, drwtim;
static const u8 recovery_values[] =
{15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
unsigned int cycle_time;
u8 setup_count, arttim = 0;
cycle_time = ide_pio_cycle_time(drive, pio);
- program_cycle_times(drive, cycle_time,
- ide_pio_timings[pio].active_time);
+ program_cycle_times(drive, cycle_time, t->active);
- setup_count = quantize_timing(ide_pio_timings[pio].setup_time,
- 1000 / system_bus_clock());
+ setup_count = quantize_timing(t->setup,
+ 1000 / (ide_pci_clk ? ide_pci_clk : 33));
/*
* The primary channel has individual address setup timing registers
static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 unit = drive->dn & 0x01;
u8 regU = 0, pciU = hwif->channel ? UDIDETCR1 : UDIDETCR0;
(void) pci_write_config_byte(dev, pciU, regU);
}
-static int cmd648_ide_dma_end (ide_drive_t *drive)
+static int cmd648_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = hwif->dma_base - (hwif->channel * 8);
return err;
}
-static int cmd64x_ide_dma_end (ide_drive_t *drive)
+static int cmd64x_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
int irq_reg = hwif->channel ? ARTTIM23 : CFR;
u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 :
CFR_INTR_CH0;
return err;
}
-static int cmd648_ide_dma_test_irq (ide_drive_t *drive)
+static int cmd648_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long base = hwif->dma_base - (hwif->channel * 8);
u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 :
MRDMODE_INTR_CH0;
- u8 dma_stat = inb(hwif->dma_status);
+ u8 dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
u8 mrdmode = inb(base + 1);
#ifdef DEBUG
return 0;
}
-static int cmd64x_ide_dma_test_irq (ide_drive_t *drive)
+static int cmd64x_dma_test_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
int irq_reg = hwif->channel ? ARTTIM23 : CFR;
u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 :
CFR_INTR_CH0;
- u8 dma_stat = inb(hwif->dma_status);
+ u8 dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
u8 irq_stat = 0;
(void) pci_read_config_byte(dev, irq_reg, &irq_stat);
* event order for DMA transfers.
*/
-static int cmd646_1_ide_dma_end (ide_drive_t *drive)
+static int cmd646_1_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
u8 dma_stat = 0, dma_cmd = 0;
drive->waiting_for_dma = 0;
/* get DMA status */
- dma_stat = inb(hwif->dma_status);
+ dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
/* read DMA command state */
- dma_cmd = inb(hwif->dma_command);
+ dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
/* stop DMA */
- outb(dma_cmd & ~1, hwif->dma_command);
+ outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD);
/* clear the INTR & ERROR bits */
- outb(dma_stat | 6, hwif->dma_status);
+ outb(dma_stat | 6, hwif->dma_base + ATA_DMA_STATUS);
/* and free any DMA resources */
ide_destroy_dmatable(drive);
/* verify good DMA status */
{
u8 mrdmode = 0;
- if (dev->device == PCI_DEVICE_ID_CMD_646) {
-
- switch (dev->revision) {
- case 0x07:
- case 0x05:
- printk("%s: UltraDMA capable\n", name);
- break;
- case 0x03:
- default:
- printk("%s: MultiWord DMA force limited\n", name);
- break;
- case 0x01:
- printk("%s: MultiWord DMA limited, "
- "IRQ workaround enabled\n", name);
- break;
- }
- }
-
/* Set a good latency timer and cache line size value. */
(void) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
/* FIXME: pci_set_master() to ensure a good latency timer value */
return 0;
}
-static u8 __devinit ata66_cmd64x(ide_hwif_t *hwif)
+static u8 __devinit cmd64x_cable_detect(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01;
switch (dev->device) {
}
}
-static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = hwif->pci_dev;
-
- hwif->set_pio_mode = &cmd64x_set_pio_mode;
- hwif->set_dma_mode = &cmd64x_set_dma_mode;
-
- if (!hwif->dma_base)
- return;
+static const struct ide_port_ops cmd64x_port_ops = {
+ .set_pio_mode = cmd64x_set_pio_mode,
+ .set_dma_mode = cmd64x_set_dma_mode,
+ .cable_detect = cmd64x_cable_detect,
+};
- /*
- * UltraDMA only supported on PCI646U and PCI646U2, which
- * correspond to revisions 0x03, 0x05 and 0x07 respectively.
- * Actually, although the CMD tech support people won't
- * tell me the details, the 0x03 revision cannot support
- * UDMA correctly without hardware modifications, and even
- * then it only works with Quantum disks due to some
- * hold time assumptions in the 646U part which are fixed
- * in the 646U2.
- *
- * So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
- */
- if (dev->device == PCI_DEVICE_ID_CMD_646 && dev->revision < 5)
- hwif->ultra_mask = 0x00;
+static const struct ide_dma_ops cmd64x_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = cmd64x_dma_end,
+ .dma_test_irq = cmd64x_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
- if (hwif->cbl != ATA_CBL_PATA40_SHORT)
- hwif->cbl = ata66_cmd64x(hwif);
+static const struct ide_dma_ops cmd646_rev1_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = cmd646_1_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
- switch (dev->device) {
- case PCI_DEVICE_ID_CMD_648:
- case PCI_DEVICE_ID_CMD_649:
- alt_irq_bits:
- hwif->ide_dma_end = &cmd648_ide_dma_end;
- hwif->ide_dma_test_irq = &cmd648_ide_dma_test_irq;
- break;
- case PCI_DEVICE_ID_CMD_646:
- if (dev->revision == 0x01) {
- hwif->ide_dma_end = &cmd646_1_ide_dma_end;
- break;
- } else if (dev->revision >= 0x03)
- goto alt_irq_bits;
- /* fall thru */
- default:
- hwif->ide_dma_end = &cmd64x_ide_dma_end;
- hwif->ide_dma_test_irq = &cmd64x_ide_dma_test_irq;
- break;
- }
-}
+static const struct ide_dma_ops cmd648_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = cmd648_dma_end,
+ .dma_test_irq = cmd648_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
static const struct ide_port_info cmd64x_chipsets[] __devinitdata = {
{ /* 0 */
.name = "CMD643",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd64x_dma_ops,
+ .host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
+ IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = 0x00, /* no udma */
},{ /* 1 */
.name = "CMD646",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.chipset = ide_cmd646,
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd648_dma_ops,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
},{ /* 2 */
.name = "CMD648",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd648_dma_ops,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
},{ /* 3 */
.name = "CMD649",
.init_chipset = init_chipset_cmd64x,
- .init_hwif = init_hwif_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
+ .port_ops = &cmd64x_port_ops,
+ .dma_ops = &cmd648_dma_ops,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
d = cmd64x_chipsets[idx];
- /*
- * The original PCI0646 didn't have the primary channel enable bit,
- * it appeared starting with PCI0646U (i.e. revision ID 3).
- */
- if (idx == 1 && dev->revision < 3)
- d.enablebits[0].reg = 0;
+ if (idx == 1) {
+ /*
+ * UltraDMA only supported on PCI646U and PCI646U2, which
+ * correspond to revisions 0x03, 0x05 and 0x07 respectively.
+ * Actually, although the CMD tech support people won't
+ * tell me the details, the 0x03 revision cannot support
+ * UDMA correctly without hardware modifications, and even
+ * then it only works with Quantum disks due to some
+ * hold time assumptions in the 646U part which are fixed
+ * in the 646U2.
+ *
+ * So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
+ */
+ if (dev->revision < 5) {
+ d.udma_mask = 0x00;
+ /*
+ * The original PCI0646 didn't have the primary
+ * channel enable bit, it appeared starting with
+ * PCI0646U (i.e. revision ID 3).
+ */
+ if (dev->revision < 3) {
+ d.enablebits[0].reg = 0;
+ if (dev->revision == 1)
+ d.dma_ops = &cmd646_rev1_dma_ops;
+ else
+ d.dma_ops = &cmd64x_dma_ops;
+ }
+ }
+ }
- return ide_setup_pci_device(dev, &d);
+ return ide_pci_init_one(dev, &d, NULL);
}
static const struct pci_device_id cmd64x_pci_tbl[] = {
.name = "CMD64x_IDE",
.id_table = cmd64x_pci_tbl,
.probe = cmd64x_init_one,
+ .remove = ide_pci_remove,
};
static int __init cmd64x_ide_init(void)
return ide_pci_register_driver(&driver);
}
+static void __exit cmd64x_ide_exit(void)
+{
+ pci_unregister_driver(&driver);
+}
+
module_init(cmd64x_ide_init);
+module_exit(cmd64x_ide_exit);
MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick");
MODULE_DESCRIPTION("PCI driver module for CMD64x IDE");
projects / linux-2.6-omap-h63xx.git / blobdiff