* The main problem with OPTi is that some timings for master
* and slave must be the same. For example, if you have master
* PIO 3 and slave PIO 0, driver have to set some timings of
- * master for PIO 0. Second problem is that opti621_tune_drive
+ * master for PIO 0. Second problem is that opti621_set_pio_mode
* got only one drive to set, but have to set both drives.
* This is solved in compute_pios. If you don't set
* the second drive, compute_pios use ide_get_best_pio_mode
#include <asm/io.h>
-#define OPTI621_MAX_PIO 3
+//#define OPTI621_MAX_PIO 3
/* In fact, I do not have any PIO 4 drive
* (address: 25 ns, data: 70 ns, recovery: 35 ns),
* but OPTi 82C621 is programmable and it can do (minimal values):
#define PIO_NOT_EXIST 254
#define PIO_DONT_KNOW 255
-/* there are stored pio numbers from other calls of opti621_tune_drive */
-static void compute_pios(ide_drive_t *drive, u8 pio)
+/* there are stored pio numbers from other calls of opti621_set_pio_mode */
+static void compute_pios(ide_drive_t *drive, const u8 pio)
/* Store values into drive->drive_data
* second_contr - 0 for primary controller, 1 for secondary
* slave_drive - 0 -> pio is for master, 1 -> pio is for slave
int d;
ide_hwif_t *hwif = HWIF(drive);
- drive->drive_data = ide_get_best_pio_mode(drive, pio, OPTI621_MAX_PIO);
+ drive->drive_data = pio;
+
for (d = 0; d < 2; ++d) {
drive = &hwif->drives[d];
if (drive->present) {
if (drive->drive_data == PIO_DONT_KNOW)
- drive->drive_data = ide_get_best_pio_mode(drive, 255, OPTI621_MAX_PIO);
+ drive->drive_data = ide_get_best_pio_mode(drive, 255, 3);
#ifdef OPTI621_DEBUG
printk("%s: Selected PIO mode %d\n",
drive->name, drive->drive_data);
}
-/* Main tune procedure, called from tuneproc. */
-static void opti621_tune_drive (ide_drive_t *drive, u8 pio)
+static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
/* primary and secondary drives share some registers,
* so we have to program both drives
*/
static void __devinit init_hwif_opti621 (ide_hwif_t *hwif)
{
- hwif->autodma = 0;
hwif->drives[0].drive_data = PIO_DONT_KNOW;
hwif->drives[1].drive_data = PIO_DONT_KNOW;
- hwif->tuneproc = &opti621_tune_drive;
+
+ hwif->set_pio_mode = &opti621_set_pio_mode;
if (!(hwif->dma_base))
return;
- hwif->atapi_dma = 1;
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
-
- if (!noautodma)
- hwif->autodma = 1;
- hwif->drives[0].autodma = hwif->autodma;
- hwif->drives[1].autodma = hwif->autodma;
}
static ide_pci_device_t opti621_chipsets[] __devinitdata = {
.enablebits = {{0x45,0x80,0x00}, {0x40,0x08,0x00}},
.bootable = ON_BOARD,
.pio_mask = ATA_PIO3,
+ .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
},{ /* 1 */
.name = "OPTI621X",
.init_hwif = init_hwif_opti621,
.enablebits = {{0x45,0x80,0x00}, {0x40,0x08,0x00}},
.bootable = ON_BOARD,
.pio_mask = ATA_PIO3,
+ .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
}
};
return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]);
}
-static struct pci_device_id opti621_pci_tbl[] = {
- { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C621, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+static const struct pci_device_id opti621_pci_tbl[] = {
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);