/*
- * linux/drivers/ide/pci/piix.c Version 0.44 March 20, 2003
+ * linux/drivers/ide/pci/piix.c Version 0.46 December 3, 2006
*
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ * Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
*
* May be copied or modified under the terms of the GNU General Public License
*
- * PIO mode setting function for Intel chipsets.
+ * PIO mode setting function for Intel chipsets.
* For use instead of BIOS settings.
*
* 40-41
* sitre = word42 & 0x4000; secondary
*
* 44 8421|8421 hdd|hdb
- *
+ *
* 48 8421 hdd|hdc|hdb|hda udma enabled
*
* 0001 hda
* if the drive cannot see an 80pin cable.
*/
if (!eighty_ninty_three(drive))
- mode = min(mode, (u8)1);
+ mode = min_t(u8, mode, 1);
return mode;
}
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
- int is_slave = (&hwif->drives[1] == drive);
+ int is_slave = drive->dn & 1;
int master_port = hwif->channel ? 0x42 : 0x40;
int slave_port = 0x44;
unsigned long flags;
static DEFINE_SPINLOCK(tune_lock);
int control = 0;
- /* ISP RTC */
+ /* ISP RTC */
static const u8 timings[][2]= {
{ 0, 0 },
{ 0, 0 },
{ 2, 1 },
{ 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 5, NULL);
+ pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
/*
* Master vs slave is synchronized above us but the slave register is
spin_lock_irqsave(&tune_lock, flags);
pci_read_config_word(dev, master_port, &master_data);
- if (pio >= 2)
+ if (pio > 1)
control |= 1; /* Programmable timing on */
if (drive->media == ide_disk)
control |= 4; /* Prefetch, post write */
- if (pio >= 3)
+ if (pio > 2)
control |= 2; /* IORDY */
if (is_slave) {
- master_data = master_data | 0x4000;
+ master_data |= 0x4000;
+ master_data &= ~0x0070;
if (pio > 1) {
/* enable PPE, IE and TIME */
master_data = master_data | (control << 4);
- } else {
- master_data &= ~0x0070;
}
pci_read_config_byte(dev, slave_port, &slave_data);
slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
} else {
- master_data = master_data & 0xccf8;
+ master_data &= ~0x3307;
if (pio > 1) {
/* enable PPE, IE and TIME */
master_data = master_data | control;
return (ide_config_drive_speed(drive, speed));
}
-/**
- * piix_faulty_dma0 - check for DMA0 errata
- * @hwif: IDE interface to check
- *
- * If an ICH/ICH0/ICH2 interface is is operating in multi-word
- * DMA mode with 600nS cycle time the IDE PIO prefetch buffer will
- * inadvertently provide an extra piece of secondary data to the primary
- * device resulting in data corruption.
- *
- * With such a device this test function returns true. This allows
- * our tuning code to follow Intel recommendations and use PIO on
- * such devices.
- */
-
-static int piix_faulty_dma0(ide_hwif_t *hwif)
-{
- switch(hwif->pci_dev->device)
- {
- case PCI_DEVICE_ID_INTEL_82801AA_1: /* ICH */
- case PCI_DEVICE_ID_INTEL_82801AB_1: /* ICH0 */
- case PCI_DEVICE_ID_INTEL_82801BA_8: /* ICH2 */
- case PCI_DEVICE_ID_INTEL_82801BA_9: /* ICH2 */
- return 1;
- }
- return 0;
-}
-
/**
* piix_config_drive_for_dma - configure drive for DMA
* @drive: IDE drive to configure
*
* Set up a PIIX interface channel for the best available speed.
- * We prefer UDMA if it is available and then MWDMA. If DMA is
- * not available we switch to PIO and return 0.
+ * We prefer UDMA if it is available and then MWDMA. If DMA is
+ * not available we switch to PIO and return 0.
*/
static int piix_config_drive_for_dma (ide_drive_t *drive)
{
u8 speed = ide_dma_speed(drive, piix_ratemask(drive));
-
- /* Some ICH devices cannot support DMA mode 0 */
- if(speed == XFER_MW_DMA_0 && piix_faulty_dma0(HWIF(drive)))
- speed = 0;
-
- /* If no DMA speed was available or the chipset has DMA bugs
- then disable DMA and use PIO */
-
- if (!speed || no_piix_dma) {
- u8 tspeed = ide_get_best_pio_mode(drive, 255, 5, NULL);
- speed = piix_dma_2_pio(XFER_PIO_0 + tspeed);
- }
+
+ /*
+ * If no DMA speed was available or the chipset has DMA bugs
+ * then disable DMA and use PIO
+ */
+ if (!speed)
+ return 0;
(void) piix_tune_chipset(drive, speed);
return ide_dma_enable(drive);
static int piix_config_drive_xfer_rate (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- struct hd_driveid *id = drive->id;
drive->init_speed = 0;
- if ((id->capability & 1) && drive->autodma) {
-
- if (ide_use_dma(drive)) {
- if (piix_config_drive_for_dma(drive))
- return hwif->ide_dma_on(drive);
- }
-
- goto fast_ata_pio;
+ if (ide_use_dma(drive) && piix_config_drive_for_dma(drive))
+ return hwif->ide_dma_on(drive);
- } else if ((id->capability & 8) || (id->field_valid & 2)) {
-fast_ata_pio:
+ if (ide_use_fast_pio(drive)) {
/* Find best PIO mode. */
- hwif->tuneproc(drive, 255);
+ (void) hwif->speedproc(drive, XFER_PIO_0 +
+ ide_get_best_pio_mode(drive, 255, 4, NULL));
return hwif->ide_dma_off_quietly(drive);
}
/* IORDY not supported */
}
/**
- * init_chipset_piix - set up the PIIX chipset
- * @dev: PCI device to set up
- * @name: Name of the device
+ * piix_is_ichx - check if ICHx
+ * @dev: PCI device to check
*
- * Initialize the PCI device as required. For the PIIX this turns
- * out to be nice and simple
+ * returns 1 if ICHx, 0 otherwise.
*/
-
-static unsigned int __devinit init_chipset_piix (struct pci_dev *dev, const char *name)
+static int piix_is_ichx(struct pci_dev *dev)
{
- switch(dev->device) {
+ switch (dev->device) {
case PCI_DEVICE_ID_INTEL_82801EB_1:
case PCI_DEVICE_ID_INTEL_82801AA_1:
case PCI_DEVICE_ID_INTEL_82801AB_1:
case PCI_DEVICE_ID_INTEL_ICH7_21:
case PCI_DEVICE_ID_INTEL_ESB2_18:
case PCI_DEVICE_ID_INTEL_ICH8_6:
- {
- unsigned int extra = 0;
- pci_read_config_dword(dev, 0x54, &extra);
- pci_write_config_dword(dev, 0x54, extra|0x400);
- }
- default:
- break;
+ return 1;
+ }
+
+ return 0;
+}
+
+/**
+ * init_chipset_piix - set up the PIIX chipset
+ * @dev: PCI device to set up
+ * @name: Name of the device
+ *
+ * Initialize the PCI device as required. For the PIIX this turns
+ * out to be nice and simple
+ */
+
+static unsigned int __devinit init_chipset_piix (struct pci_dev *dev, const char *name)
+{
+ if (piix_is_ichx(dev)) {
+ unsigned int extra = 0;
+ pci_read_config_dword(dev, 0x54, &extra);
+ pci_write_config_dword(dev, 0x54, extra|0x400);
}
return 0;
}
+/**
+ * piix_dma_clear_irq - clear BMDMA status
+ * @drive: IDE drive to clear
+ *
+ * Called from ide_intr() for PIO interrupts
+ * to clear BMDMA status as needed by ICHx
+ */
+static void piix_dma_clear_irq(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = HWIF(drive);
+ u8 dma_stat;
+
+ /* clear the INTR & ERROR bits */
+ dma_stat = hwif->INB(hwif->dma_status);
+ /* Should we force the bit as well ? */
+ hwif->OUTB(dma_stat, hwif->dma_status);
+}
+
+static int __devinit piix_cable_detect(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = hwif->pci_dev;
+ u8 reg54h = 0, mask = hwif->channel ? 0xc0 : 0x30;
+
+ pci_read_config_byte(dev, 0x54, ®54h);
+
+ return (reg54h & mask) ? 1 : 0;
+}
+
/**
* init_hwif_piix - fill in the hwif for the PIIX
* @hwif: IDE interface
static void __devinit init_hwif_piix(ide_hwif_t *hwif)
{
- u8 reg54h = 0, reg55h = 0, ata66 = 0;
- u8 mask = hwif->channel ? 0xc0 : 0x30;
-
#ifndef CONFIG_IA64
if (!hwif->irq)
hwif->irq = hwif->channel ? 15 : 14;
if (!hwif->dma_base)
return;
+ /* ICHx need to clear the bmdma status for all interrupts */
+ if (piix_is_ichx(hwif->pci_dev))
+ hwif->ide_dma_clear_irq = &piix_dma_clear_irq;
+
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x3f;
hwif->mwdma_mask = 0x06;
hwif->swdma_mask = 0x04;
switch(hwif->pci_dev->device) {
- case PCI_DEVICE_ID_INTEL_82371MX:
- hwif->mwdma_mask = 0x80;
- hwif->swdma_mask = 0x80;
case PCI_DEVICE_ID_INTEL_82371FB_0:
case PCI_DEVICE_ID_INTEL_82371FB_1:
case PCI_DEVICE_ID_INTEL_82371SB_1:
hwif->ultra_mask = 0x07;
break;
default:
- pci_read_config_byte(hwif->pci_dev, 0x54, ®54h);
- pci_read_config_byte(hwif->pci_dev, 0x55, ®55h);
- ata66 = (reg54h & mask) ? 1 : 0;
+ if (!hwif->udma_four)
+ hwif->udma_four = piix_cable_detect(hwif);
break;
}
- if (!(hwif->udma_four))
- hwif->udma_four = ata66;
+ if (no_piix_dma)
+ hwif->ultra_mask = hwif->mwdma_mask = hwif->swdma_mask = 0;
+
hwif->ide_dma_check = &piix_config_drive_xfer_rate;
if (!noautodma)
hwif->autodma = 1;
/* 0 */ DECLARE_PIIX_DEV("PIIXa"),
/* 1 */ DECLARE_PIIX_DEV("PIIXb"),
- { /* 2 */
+ /* 2 */
+ { /*
+ * MPIIX actually has only a single IDE channel mapped to
+ * the primary or secondary ports depending on the value
+ * of the bit 14 of the IDETIM register at offset 0x6c
+ */
.name = "MPIIX",
.init_hwif = init_hwif_piix,
.channels = 2,
.autodma = NODMA,
- .enablebits = {{0x6D,0x80,0x80}, {0x6F,0x80,0x80}},
+ .enablebits = {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
.bootable = ON_BOARD,
+ .flags = IDEPCI_FLAG_ISA_PORTS
},
/* 3 */ DECLARE_PIIX_DEV("PIIX3"),