#include <linux/compiler.h>
#include <linux/pci.h>
#include <linux/init.h>
-#include <linux/ioport.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/rtnetlink.h>
NETIF_MSG_LINK)
-/* enable PIO instead of MMIO, if CONFIG_8139TOO_PIO is selected */
-#ifdef CONFIG_8139TOO_PIO
-#define USE_IO_OPS 1
-#endif
-
/* define to 1, 2 or 3 to enable copious debugging info */
#define RTL8139_DEBUG 0
static int media[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
static int full_duplex[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
+/* Whether to use MMIO or PIO. Default to MMIO. */
+#ifdef CONFIG_8139TOO_PIO
+static int use_io = 1;
+#else
+static int use_io = 0;
+#endif
+
/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast).
The RTL chips use a 64 element hash table based on the Ethernet CRC. */
static int multicast_filter_limit = 32;
Cfg9346 = 0x50,
Config0 = 0x51,
Config1 = 0x52,
- FlashReg = 0x54,
+ TimerInt = 0x54,
MediaStatus = 0x58,
Config3 = 0x59,
Config4 = 0x5A, /* absent on RTL-8139A */
FIFOTMS = 0x70, /* FIFO Control and test. */
CSCR = 0x74, /* Chip Status and Configuration Register. */
PARA78 = 0x78,
+ FlashReg = 0xD4, /* Communication with Flash ROM, four bytes. */
PARA7c = 0x7c, /* Magic transceiver parameter register. */
Config5 = 0xD8, /* absent on RTL-8139A */
};
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
+module_param(use_io, int, 0);
+MODULE_PARM_DESC(use_io, "Force use of I/O access mode. 0=MMIO 1=PIO");
module_param(multicast_filter_limit, int, 0);
module_param_array(media, int, NULL, 0);
module_param_array(full_duplex, int, NULL, 0);
assert (tp->pci_dev != NULL);
pdev = tp->pci_dev;
-#ifdef USE_IO_OPS
- if (tp->mmio_addr)
- ioport_unmap (tp->mmio_addr);
-#else
if (tp->mmio_addr)
pci_iounmap (pdev, tp->mmio_addr);
-#endif /* USE_IO_OPS */
/* it's ok to call this even if we have no regions to free */
pci_release_regions (pdev);
DPRINTK("PIO region size == 0x%02X\n", pio_len);
DPRINTK("MMIO region size == 0x%02lX\n", mmio_len);
-#ifdef USE_IO_OPS
- /* make sure PCI base addr 0 is PIO */
- if (!(pio_flags & IORESOURCE_IO)) {
- dev_err(&pdev->dev, "region #0 not a PIO resource, aborting\n");
- rc = -ENODEV;
- goto err_out;
- }
- /* check for weird/broken PCI region reporting */
- if (pio_len < RTL_MIN_IO_SIZE) {
- dev_err(&pdev->dev, "Invalid PCI I/O region size(s), aborting\n");
- rc = -ENODEV;
- goto err_out;
- }
-#else
- /* make sure PCI base addr 1 is MMIO */
- if (!(mmio_flags & IORESOURCE_MEM)) {
- dev_err(&pdev->dev, "region #1 not an MMIO resource, aborting\n");
- rc = -ENODEV;
- goto err_out;
- }
- if (mmio_len < RTL_MIN_IO_SIZE) {
- dev_err(&pdev->dev, "Invalid PCI mem region size(s), aborting\n");
- rc = -ENODEV;
- goto err_out;
+retry:
+ if (use_io) {
+ /* make sure PCI base addr 0 is PIO */
+ if (!(pio_flags & IORESOURCE_IO)) {
+ dev_err(&pdev->dev, "region #0 not a PIO resource, aborting\n");
+ rc = -ENODEV;
+ goto err_out;
+ }
+ /* check for weird/broken PCI region reporting */
+ if (pio_len < RTL_MIN_IO_SIZE) {
+ dev_err(&pdev->dev, "Invalid PCI I/O region size(s), aborting\n");
+ rc = -ENODEV;
+ goto err_out;
+ }
+ } else {
+ /* make sure PCI base addr 1 is MMIO */
+ if (!(mmio_flags & IORESOURCE_MEM)) {
+ dev_err(&pdev->dev, "region #1 not an MMIO resource, aborting\n");
+ rc = -ENODEV;
+ goto err_out;
+ }
+ if (mmio_len < RTL_MIN_IO_SIZE) {
+ dev_err(&pdev->dev, "Invalid PCI mem region size(s), aborting\n");
+ rc = -ENODEV;
+ goto err_out;
+ }
}
-#endif
rc = pci_request_regions (pdev, DRV_NAME);
if (rc)
/* enable PCI bus-mastering */
pci_set_master (pdev);
-#ifdef USE_IO_OPS
- ioaddr = ioport_map(pio_start, pio_len);
- if (!ioaddr) {
- dev_err(&pdev->dev, "cannot map PIO, aborting\n");
- rc = -EIO;
- goto err_out;
- }
- dev->base_addr = pio_start;
- tp->mmio_addr = ioaddr;
- tp->regs_len = pio_len;
-#else
- /* ioremap MMIO region */
- ioaddr = pci_iomap(pdev, 1, 0);
- if (ioaddr == NULL) {
- dev_err(&pdev->dev, "cannot remap MMIO, aborting\n");
- rc = -EIO;
- goto err_out;
+ if (use_io) {
+ ioaddr = pci_iomap(pdev, 0, 0);
+ if (!ioaddr) {
+ dev_err(&pdev->dev, "cannot map PIO, aborting\n");
+ rc = -EIO;
+ goto err_out;
+ }
+ dev->base_addr = pio_start;
+ tp->regs_len = pio_len;
+ } else {
+ /* ioremap MMIO region */
+ ioaddr = pci_iomap(pdev, 1, 0);
+ if (ioaddr == NULL) {
+ dev_err(&pdev->dev, "cannot remap MMIO, trying PIO\n");
+ pci_release_regions(pdev);
+ use_io = 1;
+ goto retry;
+ }
+ dev->base_addr = (long) ioaddr;
+ tp->regs_len = mmio_len;
}
- dev->base_addr = (long) ioaddr;
tp->mmio_addr = ioaddr;
- tp->regs_len = mmio_len;
-#endif /* USE_IO_OPS */
/* Bring old chips out of low-power mode. */
RTL_W8 (HltClk, 'R');
"Use the \"8139cp\" driver for improved performance and stability.\n");
}
+ if (pdev->vendor == PCI_VENDOR_ID_REALTEK &&
+ pdev->device == PCI_DEVICE_ID_REALTEK_8139 &&
+ pdev->subsystem_vendor == PCI_VENDOR_ID_ATHEROS &&
+ pdev->subsystem_device == PCI_DEVICE_ID_REALTEK_8139) {
+ printk(KERN_INFO "8139too: OQO Model 2 detected. Forcing PIO\n");
+ use_io = 1;
+ }
+
i = rtl8139_init_board (pdev, &dev);
if (i < 0)
return i;
}
spin_lock_irqsave(&tp->lock, flags);
+ /*
+ * Writing to TxStatus triggers a DMA transfer of the data
+ * copied to tp->tx_buf[entry] above. Use a memory barrier
+ * to make sure that the device sees the updated data.
+ */
+ wmb();
RTL_W32_F (TxStatus0 + (entry * sizeof (u32)),
tp->tx_flag | max(len, (unsigned int)ETH_ZLEN));
dev->trans_start = jiffies;
tp->cur_tx++;
- wmb();
if ((tp->cur_tx - NUM_TX_DESC) == tp->dirty_tx)
netif_stop_queue (dev);
/* Malloc up new buffer, compatible with net-2e. */
/* Omit the four octet CRC from the length. */
- skb = dev_alloc_skb (pkt_size + 2);
+ skb = netdev_alloc_skb(dev, pkt_size + NET_IP_ALIGN);
if (likely(skb)) {
- skb_reserve (skb, 2); /* 16 byte align the IP fields. */
+ skb_reserve (skb, NET_IP_ALIGN); /* 16 byte align the IP fields. */
#if RX_BUF_IDX == 3
wrap_copy(skb, rx_ring, ring_offset+4, pkt_size);
#else
np->msg_enable = datum;
}
-/* TODO: we are too slack to do reg dumping for pio, for now */
-#ifdef CONFIG_8139TOO_PIO
-#define rtl8139_get_regs_len NULL
-#define rtl8139_get_regs NULL
-#else
static int rtl8139_get_regs_len(struct net_device *dev)
{
- struct rtl8139_private *np = netdev_priv(dev);
+ struct rtl8139_private *np;
+ /* TODO: we are too slack to do reg dumping for pio, for now */
+ if (use_io)
+ return 0;
+ np = netdev_priv(dev);
return np->regs_len;
}
static void rtl8139_get_regs(struct net_device *dev, struct ethtool_regs *regs, void *regbuf)
{
- struct rtl8139_private *np = netdev_priv(dev);
+ struct rtl8139_private *np;
+
+ /* TODO: we are too slack to do reg dumping for pio, for now */
+ if (use_io)
+ return;
+ np = netdev_priv(dev);
regs->version = RTL_REGS_VER;
memcpy_fromio(regbuf, np->mmio_addr, regs->len);
spin_unlock_irq(&np->lock);
}
-#endif /* CONFIG_8139TOO_MMIO */
static int rtl8139_get_sset_count(struct net_device *dev, int sset)
{
projects / linux-2.6-omap-h63xx.git / blobdiff