If you don't have this card, of course say N.
+config IP1000
+ tristate "IP1000 Gigabit Ethernet support"
+ depends on PCI && EXPERIMENTAL
+ ---help---
+ This driver supports IP1000 gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ipg. This is recommended.
+
source "drivers/net/arcnet/Kconfig"
source "drivers/net/phy/Kconfig"
If you have an Alchemy Semi AU1X00 based system
say Y. Otherwise, say N.
-config NET_SB1250_MAC
- tristate "SB1250 Ethernet support"
- depends on SIBYTE_SB1xxx_SOC
-
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
depends on PCI && SGI_IP27
tristate "Blackfin 536/537 on-chip mac support"
depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
select CRC32
+ select MII
+ select PHYLIB
select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
help
This is the driver for blackfin on-chip mac device. Say Y if you want it
<file:Documentation/networking/net-modules.txt>. The module will
be called ibmveth.
-config IBM_EMAC
- tristate "PowerPC 4xx on-chip Ethernet support"
- depends on 4xx && !PPC_MERGE
- help
- This driver supports the PowerPC 4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_RXB
- int "Number of receive buffers"
- depends on IBM_EMAC
- default "128"
-
-config IBM_EMAC_TXB
- int "Number of transmit buffers"
- depends on IBM_EMAC
- default "64"
-
-config IBM_EMAC_POLL_WEIGHT
- int "MAL NAPI polling weight"
- depends on IBM_EMAC
- default "32"
-
-config IBM_EMAC_RX_COPY_THRESHOLD
- int "RX skb copy threshold (bytes)"
- depends on IBM_EMAC
- default "256"
-
-config IBM_EMAC_RX_SKB_HEADROOM
- int "Additional RX skb headroom (bytes)"
- depends on IBM_EMAC
- default "0"
- help
- Additional receive skb headroom. Note, that driver
- will always reserve at least 2 bytes to make IP header
- aligned, so usually there is no need to add any additional
- headroom.
-
- If unsure, set to 0.
-
-config IBM_EMAC_PHY_RX_CLK_FIX
- bool "PHY Rx clock workaround"
- depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
- help
- Enable this if EMAC attached to a PHY which doesn't generate
- RX clock if there is no link, if this is the case, you will
- see "TX disable timeout" or "RX disable timeout" in the system
- log.
-
- If unsure, say N.
-
-config IBM_EMAC_DEBUG
- bool "Debugging"
- depends on IBM_EMAC
- default n
-
-config IBM_EMAC_ZMII
- bool
- depends on IBM_EMAC && (NP405H || NP405L || 44x)
- default y
-
-config IBM_EMAC_RGMII
- bool
- depends on IBM_EMAC && 440GX
- default y
-
-config IBM_EMAC_TAH
- bool
- depends on IBM_EMAC && 440GX
- default y
+source "drivers/net/ibm_emac/Kconfig"
+source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
called apricot.
config B44
- tristate "Broadcom 4400 ethernet support"
- depends on NET_PCI && PCI
+ tristate "Broadcom 440x/47xx ethernet support"
+ depends on SSB_POSSIBLE
+ select SSB
select MII
help
- If you have a network (Ethernet) controller of this type, say Y and
- read the Ethernet-HOWTO, available from
+ If you have a network (Ethernet) controller of this type, say Y
+ or M and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module will be
called b44.
+# Auto-select SSB PCI-HOST support, if possible
+config B44_PCI_AUTOSELECT
+ bool
+ depends on B44 && SSB_PCIHOST_POSSIBLE
+ select SSB_PCIHOST
+ default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B44_PCICORE_AUTOSELECT
+ bool
+ depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
+ select SSB_DRIVER_PCICORE
+ default y
+
+config B44_PCI
+ bool
+ depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
+ default y
+
config FORCEDETH
tristate "nForce Ethernet support"
depends on NET_PCI && PCI
The safe and default value for this is N.
config DL2K
- tristate "D-Link DL2000-based Gigabit Ethernet support"
+ tristate "DL2000/TC902x-based Gigabit Ethernet support"
depends on PCI
select CRC32
help
- This driver supports D-Link 2000-based gigabit ethernet cards, which
- includes
+ This driver supports DL2000/TC902x-based Gigabit ethernet cards,
+ which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
+ Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
To compile this driver as a module, choose M here: the
module will be called dl2k.
If in doubt, say Y.
+config SB1250_MAC
+ tristate "SB1250 Gigabit Ethernet support"
+ depends on SIBYTE_SB1xxx_SOC
+ ---help---
+ This driver supports Gigabit Ethernet interfaces based on the
+ Broadcom SiByte family of System-On-a-Chip parts. They include
+ the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
+ and BCM1480 chips.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sb1250-mac.
+
config SIS190
tristate "SiS190/SiS191 gigabit ethernet support"
depends on PCI
To compile the driver as a module, choose M here. The module
will be called ehea.
+config IXGBE
+ tristate "Intel(R) 10GbE PCI Express adapters support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 10GbE PCI Express family of
+ adapters. For more information on how to identify your adapter, go
+ to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbe.txt>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called ixgbe.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
---help---
- This driver supports Intel(R) PRO/10GbE family of
- adapters. For more information on how to identify your adapter, go
+ This driver supports Intel(R) PRO/10GbE family of adapters for
+ PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
+ instead. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
debug_level module parameter (which can also be set after
the driver is loaded through sysfs).
+config TEHUTI
+ tristate "Tehuti Networks 10G Ethernet"
+ depends on PCI
+ help
+ Tehuti Networks 10G Ethernet NIC
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
projects / linux-2.6-omap-h63xx.git / blobdiff