qlge: bugfix: Add flash offset for second port.

[linux-2.6-omap-h63xx.git] / drivers / net / sky2.c

diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 4dcd1a62fb490e95768c4cc8446b839890a12194..994703cc0db32c87229f7754f1a246c1cc44d9ea 100644 (file)
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1403,9 +1403,6 @@ static int sky2_up(struct net_device *dev)
 
        }
 
-       if (netif_msg_ifup(sky2))
-               printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
-
        netif_carrier_off(dev);
 
        /* must be power of 2 */
@@ -1484,6 +1481,9 @@ static int sky2_up(struct net_device *dev)
        sky2_write32(hw, B0_IMSK, imask);
 
        sky2_set_multicast(dev);
+
+       if (netif_msg_ifup(sky2))
+               printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
        return 0;
 
 err_out:
@@ -3979,7 +3979,7 @@ static int sky2_device_event(struct notifier_block *unused,
        struct net_device *dev = ptr;
        struct sky2_port *sky2 = netdev_priv(dev);
 
-       if (dev->open != sky2_up || !sky2_debug)
+       if (dev->netdev_ops->ndo_open != sky2_up || !sky2_debug)
                return NOTIFY_DONE;
 
        switch(event) {
@@ -4041,6 +4041,41 @@ static __exit void sky2_debug_cleanup(void)
 #define sky2_debug_cleanup()
 #endif
 
+/* Two copies of network device operations to handle special case of
+   not allowing netpoll on second port */
+static const struct net_device_ops sky2_netdev_ops[2] = {
+  {
+       .ndo_open               = sky2_up,
+       .ndo_stop               = sky2_down,
+       .ndo_start_xmit         = sky2_xmit_frame,
+       .ndo_do_ioctl           = sky2_ioctl,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_set_mac_address    = sky2_set_mac_address,
+       .ndo_set_multicast_list = sky2_set_multicast,
+       .ndo_change_mtu         = sky2_change_mtu,
+       .ndo_tx_timeout         = sky2_tx_timeout,
+#ifdef SKY2_VLAN_TAG_USED
+       .ndo_vlan_rx_register   = sky2_vlan_rx_register,
+#endif
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = sky2_netpoll,
+#endif
+  },
+  {
+       .ndo_open               = sky2_up,
+       .ndo_stop               = sky2_down,
+       .ndo_start_xmit         = sky2_xmit_frame,
+       .ndo_do_ioctl           = sky2_ioctl,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_set_mac_address    = sky2_set_mac_address,
+       .ndo_set_multicast_list = sky2_set_multicast,
+       .ndo_change_mtu         = sky2_change_mtu,
+       .ndo_tx_timeout         = sky2_tx_timeout,
+#ifdef SKY2_VLAN_TAG_USED
+       .ndo_vlan_rx_register   = sky2_vlan_rx_register,
+#endif
+  },
+};
 
 /* Initialize network device */
 static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
@@ -4057,20 +4092,9 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
 
        SET_NETDEV_DEV(dev, &hw->pdev->dev);
        dev->irq = hw->pdev->irq;
-       dev->open = sky2_up;
-       dev->stop = sky2_down;
-       dev->do_ioctl = sky2_ioctl;
-       dev->hard_start_xmit = sky2_xmit_frame;
-       dev->set_multicast_list = sky2_set_multicast;
-       dev->set_mac_address = sky2_set_mac_address;
-       dev->change_mtu = sky2_change_mtu;
        SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
-       dev->tx_timeout = sky2_tx_timeout;
        dev->watchdog_timeo = TX_WATCHDOG;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       if (port == 0)
-               dev->poll_controller = sky2_netpoll;
-#endif
+       dev->netdev_ops = &sky2_netdev_ops[port];
 
        sky2 = netdev_priv(dev);
        sky2->netdev = dev;
@@ -4104,7 +4128,6 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
        if (!(sky2->hw->chip_id == CHIP_ID_YUKON_FE_P &&
              sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0)) {
                dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
-               dev->vlan_rx_register = sky2_vlan_rx_register;
        }
 #endif