*
* GPL LICENSE SUMMARY
*
- * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
*
* BSD LICENSE
*
- * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*****************************************************************************/
+/*
+ * Please use this file (iwl-3945-hw.h) only for hardware-related definitions.
+ * Please use iwl-3945-commands.h for uCode API definitions.
+ * Please use iwl-3945.h for driver implementation definitions.
+ */
#ifndef __iwl_3945_hw__
#define __iwl_3945_hw__
-/* uCode queue management definitions */
+/*
+ * uCode queue management definitions ...
+ * Queue #4 is the command queue for 3945 and 4965.
+ */
#define IWL_CMD_QUEUE_NUM 4
-#define IWL_CMD_FIFO_NUM 4
-#define IWL_BACK_QUEUE_FIRST_ID 7
/* Tx rates */
#define IWL_CCK_RATES 4
#define IWL_OFDM_RATES 8
-
#define IWL_HT_RATES 0
-
#define IWL_MAX_RATES (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)
/* Time constants */
#define IWL_RSSI_OFFSET 95
/*
- * This file defines EEPROM related constants, enums, and inline functions.
- *
+ * EEPROM related constants, enums, and structures.
*/
+/*
+ * EEPROM access time values:
+ *
+ * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
+ * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
+ * CSR_EEPROM_REG_BIT_CMD (0x2).
+ * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
+ * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
+ * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
+ */
#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
-/* EEPROM field values */
-#define ANTENNA_SWITCH_NORMAL 0
-#define ANTENNA_SWITCH_INVERSE 1
+/*
+ * Regulatory channel usage flags in EEPROM struct iwl_eeprom_channel.flags.
+ *
+ * IBSS and/or AP operation is allowed *only* on those channels with
+ * (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
+ * RADAR detection is not supported by the 3945 driver, but is a
+ * requirement for establishing a new network for legal operation on channels
+ * requiring RADAR detection or restricting ACTIVE scanning.
+ *
+ * NOTE: "WIDE" flag indicates that 20 MHz channel is supported;
+ * 3945 does not support FAT 40 MHz-wide channels.
+ *
+ * NOTE: Using a channel inappropriately will result in a uCode error!
+ */
enum {
EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
- EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
+ EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
/* Bit 2 Reserved */
EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
- EEPROM_CHANNEL_WIDE = (1 << 5),
- EEPROM_CHANNEL_NARROW = (1 << 6),
+ EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
+ EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */
EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
};
-/* EEPROM field lengths */
-#define EEPROM_BOARD_PBA_NUMBER_LENGTH 11
-
-/* EEPROM field lengths */
-#define EEPROM_BOARD_PBA_NUMBER_LENGTH 11
-#define EEPROM_REGULATORY_SKU_ID_LENGTH 4
-#define EEPROM_REGULATORY_BAND1_CHANNELS_LENGTH 14
-#define EEPROM_REGULATORY_BAND2_CHANNELS_LENGTH 13
-#define EEPROM_REGULATORY_BAND3_CHANNELS_LENGTH 12
-#define EEPROM_REGULATORY_BAND4_CHANNELS_LENGTH 11
-#define EEPROM_REGULATORY_BAND5_CHANNELS_LENGTH 6
-
-#define EEPROM_REGULATORY_CHANNELS_LENGTH ( \
- EEPROM_REGULATORY_BAND1_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND2_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND3_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND4_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND5_CHANNELS_LENGTH)
-
-#define EEPROM_REGULATORY_NUMBER_OF_BANDS 5
-
/* SKU Capabilities */
#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
#define EEPROM_SKU_CAP_OP_MODE_MRC (1 << 7)
/* *regulatory* channel data from eeprom, one for each channel */
-struct iwl_eeprom_channel {
+struct iwl3945_eeprom_channel {
u8 flags; /* flags copied from EEPROM */
s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
} __attribute__ ((packed));
* long packets in normal operation to provide feedback as to proper output
* level.
* Data copied from EEPROM.
+ * DO NOT ALTER THIS STRUCTURE!!!
*/
-struct iwl_eeprom_txpower_sample {
+struct iwl3945_eeprom_txpower_sample {
u8 gain_index; /* index into power (gain) setup table ... */
s8 power; /* ... for this pwr level for this chnl group */
u16 v_det; /* PA output voltage */
* Data copied from EEPROM.
* DO NOT ALTER THIS STRUCTURE!!!
*/
-struct iwl_eeprom_txpower_group {
- struct iwl_eeprom_txpower_sample samples[5]; /* 5 power levels */
+struct iwl3945_eeprom_txpower_group {
+ struct iwl3945_eeprom_txpower_sample samples[5]; /* 5 power levels */
s32 a, b, c, d, e; /* coefficients for voltage->power
* formula (signed) */
s32 Fa, Fb, Fc, Fd, Fe; /* these modify coeffs based on
- * frequency (signed) */
+ * frequency (signed) */
s8 saturation_power; /* highest power possible by h/w in this
* band */
u8 group_channel; /* "representative" channel # in this band */
* difference between current temperature and factory calib temperature.
* Data copied from EEPROM.
*/
-struct iwl_eeprom_temperature_corr {
+struct iwl3945_eeprom_temperature_corr {
u32 Ta;
u32 Tb;
u32 Tc;
u32 Te;
} __attribute__ ((packed));
-struct iwl_eeprom {
+/*
+ * EEPROM map
+ */
+struct iwl3945_eeprom {
u8 reserved0[16];
-#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
u16 device_id; /* abs.ofs: 16 */
u8 reserved1[2];
-#define EEPROM_PMC (2*0x0A) /* 2 bytes */
u16 pmc; /* abs.ofs: 20 */
u8 reserved2[20];
-#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
u8 mac_address[6]; /* abs.ofs: 42 */
u8 reserved3[58];
-#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
u16 board_revision; /* abs.ofs: 106 */
u8 reserved4[11];
-#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
u8 board_pba_number[9]; /* abs.ofs: 119 */
u8 reserved5[8];
-#define EEPROM_VERSION (2*0x44) /* 2 bytes */
u16 version; /* abs.ofs: 136 */
-#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
u8 sku_cap; /* abs.ofs: 138 */
-#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
u8 leds_mode; /* abs.ofs: 139 */
-#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
u16 oem_mode;
-#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
u16 wowlan_mode; /* abs.ofs: 142 */
-#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
u16 leds_time_interval; /* abs.ofs: 144 */
-#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
u8 leds_off_time; /* abs.ofs: 146 */
-#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
u8 leds_on_time; /* abs.ofs: 147 */
-#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
u8 almgor_m_version; /* abs.ofs: 148 */
-#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
u8 antenna_switch_type; /* abs.ofs: 149 */
u8 reserved6[42];
-#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
u8 sku_id[4]; /* abs.ofs: 192 */
-#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
+
+/*
+ * Per-channel regulatory data.
+ *
+ * Each channel that *might* be supported by 3945 or 4965 has a fixed location
+ * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
+ * txpower (MSB).
+ *
+ * Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
+ * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
+ *
+ * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
+ */
u16 band_1_count; /* abs.ofs: 196 */
-#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
- struct iwl_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
-#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
+ struct iwl3945_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
+
+/*
+ * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
+ * 5.0 GHz channels 7, 8, 11, 12, 16
+ * (4915-5080MHz) (none of these is ever supported)
+ */
u16 band_2_count; /* abs.ofs: 226 */
-#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
- struct iwl_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
-#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
+ struct iwl3945_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
+
+/*
+ * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
+ * (5170-5320MHz)
+ */
u16 band_3_count; /* abs.ofs: 254 */
-#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
- struct iwl_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
-#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */
+ struct iwl3945_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
+
+/*
+ * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
+ * (5500-5700MHz)
+ */
u16 band_4_count; /* abs.ofs: 280 */
-#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */
- struct iwl_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
-#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */
+ struct iwl3945_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
+
+/*
+ * 5.7 GHz channels 145, 149, 153, 157, 161, 165
+ * (5725-5825MHz)
+ */
u16 band_5_count; /* abs.ofs: 304 */
-#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
- struct iwl_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
+ struct iwl3945_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
u8 reserved9[194];
-#define EEPROM_TXPOWER_CALIB_GROUP0 0x200
-#define EEPROM_TXPOWER_CALIB_GROUP1 0x240
-#define EEPROM_TXPOWER_CALIB_GROUP2 0x280
-#define EEPROM_TXPOWER_CALIB_GROUP3 0x2c0
-#define EEPROM_TXPOWER_CALIB_GROUP4 0x300
+/*
+ * 3945 Txpower calibration data.
+ */
#define IWL_NUM_TX_CALIB_GROUPS 5
- struct iwl_eeprom_txpower_group groups[IWL_NUM_TX_CALIB_GROUPS];
+ struct iwl3945_eeprom_txpower_group groups[IWL_NUM_TX_CALIB_GROUPS];
/* abs.ofs: 512 */
-#define EEPROM_CALIB_TEMPERATURE_CORRECT 0x340
- struct iwl_eeprom_temperature_corr corrections; /* abs.ofs: 832 */
+ struct iwl3945_eeprom_temperature_corr corrections; /* abs.ofs: 832 */
u8 reserved16[172]; /* fill out to full 1024 byte block */
} __attribute__ ((packed));
#define IWL_EEPROM_IMAGE_SIZE 1024
+/* End of EEPROM */
+
#include "iwl-3945-commands.h"
#define PCI_REG_WUM8 0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
-/*=== CSR (control and status registers) ===*/
-#define CSR_BASE (0x000)
-
-#define CSR_SW_VER (CSR_BASE+0x000)
-#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
-#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
-#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
-#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
-#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
-#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
-#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
-#define CSR_GP_CNTRL (CSR_BASE+0x024)
-#define CSR_HW_REV (CSR_BASE+0x028)
-#define CSR_EEPROM_REG (CSR_BASE+0x02c)
-#define CSR_EEPROM_GP (CSR_BASE+0x030)
-#define CSR_GP_UCODE (CSR_BASE+0x044)
-#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
-#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
-#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
-#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_LED_REG (CSR_BASE+0x094)
-#define CSR_DRAM_INT_TBL_CTL (CSR_BASE+0x0A0)
-#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
-#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
-#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
-
-/* HW I/F configuration */
-#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB (0x00000100)
-#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM (0x00000200)
-#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400)
-#define CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800)
-#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000)
-#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000)
-#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
-
-/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
- * acknowledged (reset) by host writing "1" to flagged bits. */
-#define CSR_INT_BIT_FH_RX (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */
-#define CSR_INT_BIT_HW_ERR (1<<29) /* DMA hardware error FH_INT[31] */
-#define CSR_INT_BIT_DNLD (1<<28) /* uCode Download */
-#define CSR_INT_BIT_FH_TX (1<<27) /* Tx DMA FH_INT[1:0] */
-#define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */
-#define CSR_INT_BIT_SW_ERR (1<<25) /* uCode error */
-#define CSR_INT_BIT_RF_KILL (1<<7) /* HW RFKILL switch GP_CNTRL[27] toggled */
-#define CSR_INT_BIT_CT_KILL (1<<6) /* Critical temp (chip too hot) rfkill */
-#define CSR_INT_BIT_SW_RX (1<<3) /* Rx, command responses, 3945 */
-#define CSR_INT_BIT_WAKEUP (1<<1) /* NIC controller waking up (pwr mgmt) */
-#define CSR_INT_BIT_ALIVE (1<<0) /* uCode interrupts once it initializes */
-
-#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
- CSR_INT_BIT_HW_ERR | \
- CSR_INT_BIT_FH_TX | \
- CSR_INT_BIT_SW_ERR | \
- CSR_INT_BIT_RF_KILL | \
- CSR_INT_BIT_SW_RX | \
- CSR_INT_BIT_WAKEUP | \
- CSR_INT_BIT_ALIVE)
-
-/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
-#define CSR_FH_INT_BIT_ERR (1<<31) /* Error */
-#define CSR_FH_INT_BIT_HI_PRIOR (1<<30) /* High priority Rx, bypass coalescing */
-#define CSR_FH_INT_BIT_RX_CHNL2 (1<<18) /* Rx channel 2 (3945 only) */
-#define CSR_FH_INT_BIT_RX_CHNL1 (1<<17) /* Rx channel 1 */
-#define CSR_FH_INT_BIT_RX_CHNL0 (1<<16) /* Rx channel 0 */
-#define CSR_FH_INT_BIT_TX_CHNL6 (1<<6) /* Tx channel 6 (3945 only) */
-#define CSR_FH_INT_BIT_TX_CHNL1 (1<<1) /* Tx channel 1 */
-#define CSR_FH_INT_BIT_TX_CHNL0 (1<<0) /* Tx channel 0 */
-
-#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
- CSR_FH_INT_BIT_RX_CHNL2 | \
- CSR_FH_INT_BIT_RX_CHNL1 | \
- CSR_FH_INT_BIT_RX_CHNL0)
-
-#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL6 | \
- CSR_FH_INT_BIT_TX_CHNL1 | \
- CSR_FH_INT_BIT_TX_CHNL0 )
-
-
-/* RESET */
-#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
-#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
-#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
-#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
-#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
-
-/* GP (general purpose) CONTROL */
-#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
-#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
-#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
-
-#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
-
-#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
-#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
-
-
-/* EEPROM REG */
-#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
-#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
-
-/* EEPROM GP */
-#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
-#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
-#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
-
-/* UCODE DRV GP */
-#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
-#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
-#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
-#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
-
-/* GPIO */
-#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
-#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
-#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
-
-/* GI Chicken Bits */
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
-
-/* CSR_ANA_PLL_CFG */
-#define CSR_ANA_PLL_CFG_SH (0x00880300)
-
-#define CSR_LED_REG_TRUN_ON (0x00000078)
-#define CSR_LED_REG_TRUN_OFF (0x00000038)
-#define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF)
-
-/* DRAM_INT_TBL_CTRL */
-#define CSR_DRAM_INT_TBL_CTRL_EN (1<<31)
-#define CSR_DRAM_INT_TBL_CTRL_WRAP_CHK (1<<27)
-
-/*=== HBUS (Host-side Bus) ===*/
-#define HBUS_BASE (0x400)
-
-#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
-#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
-#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
-#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
-#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
-#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
-#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
-#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
-#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
-
-#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
-
-
-/* SCD (Scheduler) */
+/* SCD (3945 Tx Frame Scheduler) */
#define SCD_BASE (CSR_BASE + 0x2E00)
#define SCD_MODE_REG (SCD_BASE + 0x000)
#define FH_TSSR_CBB_BASE (FH_TSSR_TABLE+0x000)
#define FH_TSSR_MSG_CONFIG (FH_TSSR_TABLE+0x008)
#define FH_TSSR_TX_STATUS (FH_TSSR_TABLE+0x010)
-/* 18 - reserved */
-
-/* card static random access memory (SRAM) for processor data and instructs */
-#define RTC_INST_LOWER_BOUND (0x000000)
-#define RTC_DATA_LOWER_BOUND (0x800000)
/* DBM */
#define PCI_CFG_REV_ID_BIT_BASIC_SKU (0x40) /* bit 6 */
#define PCI_CFG_REV_ID_BIT_RTP (0x80) /* bit 7 */
-#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
-
#define TFD_QUEUE_MIN 0
#define TFD_QUEUE_MAX 6
#define TFD_QUEUE_SIZE_MAX (256)
-/* spectrum and channel data structures */
#define IWL_NUM_SCAN_RATES (2)
-#define IWL_SCAN_FLAG_24GHZ (1<<0)
-#define IWL_SCAN_FLAG_52GHZ (1<<1)
-#define IWL_SCAN_FLAG_ACTIVE (1<<2)
-#define IWL_SCAN_FLAG_DIRECT (1<<3)
-
-#define IWL_MAX_CMD_SIZE 1024
-
#define IWL_DEFAULT_TX_RETRY 15
-#define IWL_MAX_TX_RETRY 16
/*********************************************/
#define RX_QUEUE_MASK 255
#define RX_QUEUE_SIZE_LOG 8
-/* QoS definitions */
-
-#define CW_MIN_OFDM 15
-#define CW_MAX_OFDM 1023
-#define CW_MIN_CCK 31
-#define CW_MAX_CCK 1023
-
-#define QOS_TX0_CW_MIN_OFDM CW_MIN_OFDM
-#define QOS_TX1_CW_MIN_OFDM CW_MIN_OFDM
-#define QOS_TX2_CW_MIN_OFDM ((CW_MIN_OFDM + 1) / 2 - 1)
-#define QOS_TX3_CW_MIN_OFDM ((CW_MIN_OFDM + 1) / 4 - 1)
-
-#define QOS_TX0_CW_MIN_CCK CW_MIN_CCK
-#define QOS_TX1_CW_MIN_CCK CW_MIN_CCK
-#define QOS_TX2_CW_MIN_CCK ((CW_MIN_CCK + 1) / 2 - 1)
-#define QOS_TX3_CW_MIN_CCK ((CW_MIN_CCK + 1) / 4 - 1)
-
-#define QOS_TX0_CW_MAX_OFDM CW_MAX_OFDM
-#define QOS_TX1_CW_MAX_OFDM CW_MAX_OFDM
-#define QOS_TX2_CW_MAX_OFDM CW_MIN_OFDM
-#define QOS_TX3_CW_MAX_OFDM ((CW_MIN_OFDM + 1) / 2 - 1)
-
-#define QOS_TX0_CW_MAX_CCK CW_MAX_CCK
-#define QOS_TX1_CW_MAX_CCK CW_MAX_CCK
-#define QOS_TX2_CW_MAX_CCK CW_MIN_CCK
-#define QOS_TX3_CW_MAX_CCK ((CW_MIN_CCK + 1) / 2 - 1)
-
-#define QOS_TX0_AIFS 3
-#define QOS_TX1_AIFS 7
-#define QOS_TX2_AIFS 2
-#define QOS_TX3_AIFS 2
-
-#define QOS_TX0_ACM 0
-#define QOS_TX1_ACM 0
-#define QOS_TX2_ACM 0
-#define QOS_TX3_ACM 0
-
-#define QOS_TX0_TXOP_LIMIT_CCK 0
-#define QOS_TX1_TXOP_LIMIT_CCK 0
-#define QOS_TX2_TXOP_LIMIT_CCK 6016
-#define QOS_TX3_TXOP_LIMIT_CCK 3264
-
-#define QOS_TX0_TXOP_LIMIT_OFDM 0
-#define QOS_TX1_TXOP_LIMIT_OFDM 0
-#define QOS_TX2_TXOP_LIMIT_OFDM 3008
-#define QOS_TX3_TXOP_LIMIT_OFDM 1504
-
-#define DEF_TX0_CW_MIN_OFDM CW_MIN_OFDM
-#define DEF_TX1_CW_MIN_OFDM CW_MIN_OFDM
-#define DEF_TX2_CW_MIN_OFDM CW_MIN_OFDM
-#define DEF_TX3_CW_MIN_OFDM CW_MIN_OFDM
-
-#define DEF_TX0_CW_MIN_CCK CW_MIN_CCK
-#define DEF_TX1_CW_MIN_CCK CW_MIN_CCK
-#define DEF_TX2_CW_MIN_CCK CW_MIN_CCK
-#define DEF_TX3_CW_MIN_CCK CW_MIN_CCK
-
-#define DEF_TX0_CW_MAX_OFDM CW_MAX_OFDM
-#define DEF_TX1_CW_MAX_OFDM CW_MAX_OFDM
-#define DEF_TX2_CW_MAX_OFDM CW_MAX_OFDM
-#define DEF_TX3_CW_MAX_OFDM CW_MAX_OFDM
-
-#define DEF_TX0_CW_MAX_CCK CW_MAX_CCK
-#define DEF_TX1_CW_MAX_CCK CW_MAX_CCK
-#define DEF_TX2_CW_MAX_CCK CW_MAX_CCK
-#define DEF_TX3_CW_MAX_CCK CW_MAX_CCK
-
-#define DEF_TX0_AIFS (2)
-#define DEF_TX1_AIFS (2)
-#define DEF_TX2_AIFS (2)
-#define DEF_TX3_AIFS (2)
-
-#define DEF_TX0_ACM 0
-#define DEF_TX1_ACM 0
-#define DEF_TX2_ACM 0
-#define DEF_TX3_ACM 0
-
-#define DEF_TX0_TXOP_LIMIT_CCK 0
-#define DEF_TX1_TXOP_LIMIT_CCK 0
-#define DEF_TX2_TXOP_LIMIT_CCK 0
-#define DEF_TX3_TXOP_LIMIT_CCK 0
-
-#define DEF_TX0_TXOP_LIMIT_OFDM 0
-#define DEF_TX1_TXOP_LIMIT_OFDM 0
-#define DEF_TX2_TXOP_LIMIT_OFDM 0
-#define DEF_TX3_TXOP_LIMIT_OFDM 0
-
-#define QOS_QOS_SETS 3
-#define QOS_PARAM_SET_ACTIVE 0
-#define QOS_PARAM_SET_DEF_CCK 1
-#define QOS_PARAM_SET_DEF_OFDM 2
-
-#define CTRL_QOS_NO_ACK (0x0020)
-#define DCT_FLAG_EXT_QOS_ENABLED (0x10)
-
#define U32_PAD(n) ((4-(n))&0x3)
-/*
- * Generic queue structure
- *
- * Contains common data for Rx and Tx queues
- */
-#define TFD_CTL_COUNT_SET(n) (n<<24)
-#define TFD_CTL_COUNT_GET(ctl) ((ctl>>24) & 7)
-#define TFD_CTL_PAD_SET(n) (n<<28)
-#define TFD_CTL_PAD_GET(ctl) (ctl>>28)
+#define TFD_CTL_COUNT_SET(n) (n << 24)
+#define TFD_CTL_COUNT_GET(ctl) ((ctl >> 24) & 7)
+#define TFD_CTL_PAD_SET(n) (n << 28)
+#define TFD_CTL_PAD_GET(ctl) (ctl >> 28)
#define TFD_TX_CMD_SLOTS 256
#define TFD_CMD_SLOTS 32
-#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl_cmd) - \
- sizeof(struct iwl_cmd_meta))
+#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl3945_cmd) - \
+ sizeof(struct iwl3945_cmd_meta))
/*
* RX related structures and functions
#define RX_FREE_BUFFERS 64
#define RX_LOW_WATERMARK 8
-
-#define IWL_RX_BUF_SIZE 3000
-/* card static random access memory (SRAM) for processor data and instructs */
+/* Sizes and addresses for instruction and data memory (SRAM) in
+ * 3945's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */
+#define RTC_INST_LOWER_BOUND (0x000000)
#define ALM_RTC_INST_UPPER_BOUND (0x014000)
+
+#define RTC_DATA_LOWER_BOUND (0x800000)
#define ALM_RTC_DATA_UPPER_BOUND (0x808000)
#define ALM_RTC_INST_SIZE (ALM_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
#define ALM_RTC_DATA_SIZE (ALM_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
-#define IWL_MAX_BSM_SIZE ALM_RTC_INST_SIZE
#define IWL_MAX_INST_SIZE ALM_RTC_INST_SIZE
#define IWL_MAX_DATA_SIZE ALM_RTC_DATA_SIZE
+
+/* Size of uCode instruction memory in bootstrap state machine */
+#define IWL_MAX_BSM_SIZE ALM_RTC_INST_SIZE
+
#define IWL_MAX_NUM_QUEUES 8
-static inline int iwl_hw_valid_rtc_data_addr(u32 addr)
+static inline int iwl3945_hw_valid_rtc_data_addr(u32 addr)
{
return (addr >= RTC_DATA_LOWER_BOUND) &&
(addr < ALM_RTC_DATA_UPPER_BOUND);
}
-/* Base physical address of iwl_shared is provided to FH_TSSR_CBB_BASE
- * and &iwl_shared.rx_read_ptr[0] is provided to FH_RCSR_RPTR_ADDR(0) */
-struct iwl_shared {
+/* Base physical address of iwl3945_shared is provided to FH_TSSR_CBB_BASE
+ * and &iwl3945_shared.rx_read_ptr[0] is provided to FH_RCSR_RPTR_ADDR(0) */
+struct iwl3945_shared {
__le32 tx_base_ptr[8];
__le32 rx_read_ptr[3];
} __attribute__ ((packed));
-struct iwl_tfd_frame_data {
+struct iwl3945_tfd_frame_data {
__le32 addr;
__le32 len;
} __attribute__ ((packed));
-struct iwl_tfd_frame {
+struct iwl3945_tfd_frame {
__le32 control_flags;
- struct iwl_tfd_frame_data pa[4];
+ struct iwl3945_tfd_frame_data pa[4];
u8 reserved[28];
} __attribute__ ((packed));
-static inline u8 iwl_hw_get_rate(__le16 rate_n_flags)
+static inline u8 iwl3945_hw_get_rate(__le16 rate_n_flags)
{
return le16_to_cpu(rate_n_flags) & 0xFF;
}
-static inline u16 iwl_hw_get_rate_n_flags(__le16 rate_n_flags)
+static inline u16 iwl3945_hw_get_rate_n_flags(__le16 rate_n_flags)
{
return le16_to_cpu(rate_n_flags);
}
-static inline __le16 iwl_hw_set_rate_n_flags(u8 rate, u16 flags)
+static inline __le16 iwl3945_hw_set_rate_n_flags(u8 rate, u16 flags)
{
return cpu_to_le16((u16)rate|flags);
}
projects / linux-2.6-omap-h63xx.git / blobdiff