#define TI122X_SCR_SER_STEP 0xc0000000
#define TI122X_SCR_INTRTIE 0x20000000
+#define TIXX21_SCR_TIEALL 0x10000000
#define TI122X_SCR_CBRSVD 0x00400000
#define TI122X_SCR_MRBURSTDN 0x00008000
#define TI122X_SCR_MRBURSTUP 0x00004000
/* EnE test register */
#define ENE_TEST_C9 0xc9 /* 8bit */
#define ENE_TEST_C9_TLTENABLE 0x02
+#define ENE_TEST_C9_PFENABLE_F0 0x04
+#define ENE_TEST_C9_PFENABLE_F1 0x08
+#define ENE_TEST_C9_PFENABLE (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F0)
+#define ENE_TEST_C9_WPDISALBLE_F0 0x40
+#define ENE_TEST_C9_WPDISALBLE_F1 0x80
+#define ENE_TEST_C9_WPDISALBLE (ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
/*
* Texas Instruments CardBus controller overrides.
int devfn;
unsigned int state;
int ret = 1;
+ u32 sysctl;
/* catch the two-slot controllers */
switch (socket->dev->device) {
*/
break;
+ case PCI_DEVICE_ID_TI_X515:
+ case PCI_DEVICE_ID_TI_X420:
+ case PCI_DEVICE_ID_TI_X620:
+ case PCI_DEVICE_ID_TI_XX21_XX11:
+ case PCI_DEVICE_ID_TI_7410:
+ case PCI_DEVICE_ID_TI_7610:
+ /*
+ * those are either single or dual slot CB with additional functions
+ * like 1394, smartcard reader, etc. check the TIEALL flag for them
+ * the TIEALL flag binds the IRQ of all functions toghether.
+ * we catch the single slot variants later.
+ */
+ sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+ if (sysctl & TIXX21_SCR_TIEALL)
+ return 0;
+
+ break;
+
/* single-slot controllers have the 2nd slot empty always :) */
default:
return 1;
if (!func)
return 1;
+ /*
+ * check that the device id of both slots match. this is needed for the
+ * XX21 and the XX11 controller that share the same device id for single
+ * and dual slot controllers. return '2nd slot empty'. we already checked
+ * if the interrupt is tied to another function.
+ */
+ if (socket->dev->device != func->device)
+ goto out;
+
slot2 = pci_get_drvdata(func);
if (!slot2)
goto out;
if (val_orig != val)
config_writel(socket, TI113X_SYSTEM_CONTROL, val);
- /*
- * for EnE bridges only: clear testbit TLTEnable. this makes the
- * RME Hammerfall DSP sound card working.
- */
- if (socket->dev->vendor == PCI_VENDOR_ID_ENE) {
- u8 test_c9 = config_readb(socket, ENE_TEST_C9);
- test_c9 &= ~ENE_TEST_C9_TLTENABLE;
- config_writeb(socket, ENE_TEST_C9, test_c9);
- }
-
/*
* Yenta expects controllers to use CSCINT to route
* CSC interrupts to PCI rather than INTVAL.
return ti12xx_override(socket);
}
+
+/**
+ * EnE specific part. EnE bridges are register compatible with TI bridges but
+ * have their own test registers and more important their own little problems.
+ * Some fixup code to make everybody happy (TM).
+ */
+
+#ifdef CONFIG_YENTA_ENE_TUNE
+/**
+ * set/clear various test bits:
+ * Defaults to clear the bit.
+ * - mask (u8) defines what bits to change
+ * - bits (u8) is the values to change them to
+ * -> it's
+ * current = (current & ~mask) | bits
+ */
+/* pci ids of devices that wants to have the bit set */
+#define DEVID(_vend,_dev,_subvend,_subdev,mask,bits) { \
+ .vendor = _vend, \
+ .device = _dev, \
+ .subvendor = _subvend, \
+ .subdevice = _subdev, \
+ .driver_data = ((mask) << 8 | (bits)), \
+ }
+static struct pci_device_id ene_tune_tbl[] = {
+ /* Echo Audio products based on motorola DSP56301 and DSP56361 */
+ DEVID(PCI_VENDOR_ID_MOTOROLA, 0x1801, 0xECC0, PCI_ANY_ID,
+ ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
+ DEVID(PCI_VENDOR_ID_MOTOROLA, 0x3410, 0xECC0, PCI_ANY_ID,
+ ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
+
+ {}
+};
+
+static void ene_tune_bridge(struct pcmcia_socket *sock, struct pci_bus *bus)
+{
+ struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+ struct pci_dev *dev;
+ struct pci_device_id *id = NULL;
+ u8 test_c9, old_c9, mask, bits;
+
+ list_for_each_entry(dev, &bus->devices, bus_list) {
+ id = (struct pci_device_id *) pci_match_id(ene_tune_tbl, dev);
+ if (id)
+ break;
+ }
+
+ test_c9 = old_c9 = config_readb(socket, ENE_TEST_C9);
+ if (id) {
+ mask = (id->driver_data >> 8) & 0xFF;
+ bits = id->driver_data & 0xFF;
+
+ test_c9 = (test_c9 & ~mask) | bits;
+ }
+ else
+ /* default to clear TLTEnable bit, old behaviour */
+ test_c9 &= ~ENE_TEST_C9_TLTENABLE;
+
+ printk(KERN_INFO "yenta EnE: chaning testregister 0xC9, %02x -> %02x\n", old_c9, test_c9);
+ config_writeb(socket, ENE_TEST_C9, test_c9);
+}
+
+static int ene_override(struct yenta_socket *socket)
+{
+ /* install tune_bridge() function */
+ socket->socket.tune_bridge = ene_tune_bridge;
+
+ return ti1250_override(socket);
+}
+#else
+# define ene_override ti1250_override
+#endif /* !CONFIG_YENTA_ENE_TUNE */
+
#endif /* _LINUX_TI113X_H */
projects / linux-2.6-omap-h63xx.git / blobdiff