Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

[linux-2.6-omap-h63xx.git] / drivers / serial / Kconfig

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 819fc3efc4681aabc1d66d62ace1d58be033f81b..ed438bc7e98da46549a25c8caeb3e839b1c777ad 100644 (file)
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -62,11 +62,11 @@ config SERIAL_8250_CONSOLE
          kernel will automatically use the first serial line, /dev/ttyS0, as
          system console.
 
-         you can set that using a kernel command line option such as
+         You can set that using a kernel command line option such as
          "console=uart8250,io,0x3f8,9600n8"
          "console=uart8250,mmio,0xff5e0000,115200n8".
-         and it will switch to normal serial console when correponding port is
-         ready.
+         and it will switch to normal serial console when the corresponding 
+         port is ready.
          "earlycon=uart8250,io,0x3f8,9600n8"
          "earlycon=uart8250,mmio,0xff5e0000,115200n8".
          it will not only setup early console.
@@ -611,7 +611,7 @@ config SERIAL_BFIN
 
 config SERIAL_BFIN_CONSOLE
        bool "Console on Blackfin serial port"
-       depends on SERIAL_BFIN
+       depends on SERIAL_BFIN=y
        select SERIAL_CORE_CONSOLE
 
 choice
@@ -624,7 +624,7 @@ choice
 
 config SERIAL_BFIN_DMA
        bool "DMA mode"
-       depends on DMA_UNCACHED_1M && !KGDB_UART
+       depends on !DMA_UNCACHED_NONE && !KGDB_UART
        help
          This driver works under DMA mode. If this option is selected, the
          blackfin simple dma driver is also enabled.
@@ -832,10 +832,10 @@ config SERIAL_MUX
            4. Change the kernel command console parameter to: console=ttyB0
 
 config SERIAL_MUX_CONSOLE
-        bool "Support for console on serial MUX"
-        depends on SERIAL_MUX
+       bool "Support for console on serial MUX"
+       depends on SERIAL_MUX=y
        select SERIAL_CORE_CONSOLE
-        default y
+       default y
 
 config PDC_CONSOLE
        bool "PDC software console support"
@@ -986,6 +986,31 @@ config SERIAL_PMACZILOG
          PowerMac machines.
          Say Y or M if you want to be able to these serial ports.
 
+config SERIAL_PMACZILOG_TTYS
+       bool "Use ttySn device nodes for Zilog z85c30"
+       depends on SERIAL_PMACZILOG
+       help
+         The pmac_zilog driver for the z85C30 chip on many powermacs
+         historically used the device numbers for /dev/ttySn.  The
+         8250 serial port driver also uses these numbers, which means
+         the two drivers being unable to coexist; you could not use
+         both z85C30 and 8250 type ports at the same time.
+
+         If this option is not selected, the pmac_zilog driver will
+         use the device numbers allocated for /dev/ttyPZn.  This allows
+         the pmac_zilog and 8250 drivers to co-exist, but may cause
+         existing userspace setups to break.  Programs that need to
+         access the built-in serial ports on powermacs will need to
+         be reconfigured to use /dev/ttyPZn instead of /dev/ttySn.
+
+         If you enable this option, any z85c30 ports in the system will
+         be registered as ttyS0 onwards as in the past, and you will be
+         unable to use the 8250 module for PCMCIA or other 16C550-style
+         UARTs.
+
+         Say N unless you need the z85c30 ports on your powermac
+         to appear as /dev/ttySn.
+
 config SERIAL_PMACZILOG_CONSOLE
        bool "Console on PowerMac z85c30 serial port"
        depends on SERIAL_PMACZILOG=y
@@ -1191,7 +1216,7 @@ config SERIAL_VR41XX
 
 config SERIAL_VR41XX_CONSOLE
        bool "Enable NEC VR4100 series Serial Interface Unit console"
-       depends on SERIAL_VR41XX
+       depends on SERIAL_VR41XX=y
        select SERIAL_CORE_CONSOLE
        help
          If you have a NEC VR4100 series processor and you want to use