/*
* Blackfin On-Chip Serial Driver
*
- * Copyright 2006-2007 Analog Devices Inc.
+ * Copyright 2006-2008 Analog Devices Inc.
*
* Enter bugs at http://blackfin.uclinux.org/
*
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
-#ifdef CONFIG_KGDB_UART
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
#include <linux/kgdb.h>
#include <asm/irq_regs.h>
#endif
#define BFIN_SERIAL_MAJOR 204
#define BFIN_SERIAL_MINOR 64
+static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
+static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
+
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+
+# ifndef CONFIG_SERIAL_BFIN_PIO
+# error KGDB only support UART in PIO mode.
+# endif
+
+static int kgdboc_port_line;
+static int kgdboc_break_enabled;
+#endif
/*
* Setup for console. Argument comes from the menuconfig
*/
#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
#define DMA_RX_FLUSH_JIFFIES (HZ / 50)
-#define CTS_CHECK_JIFFIES (HZ / 50)
#ifdef CONFIG_SERIAL_BFIN_DMA
static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
#endif
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
+static void bfin_serial_reset_irda(struct uart_port *port);
+
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->cts_pin < 0)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ /* CTS PIN is negative assertive. */
+ if (UART_GET_CTS(uart))
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ else
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->rts_pin < 0)
+ return;
+
+ /* RTS PIN is negative assertive. */
+ if (mctrl & TIOCM_RTS)
+ UART_ENABLE_RTS(uart);
+ else
+ UART_DISABLE_RTS(uart);
+}
+
+/*
+ * Handle any change of modem status signal.
+ */
+static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned int status;
+
+ status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ uart->scts = 1;
+ UART_CLEAR_SCTS(uart);
+ UART_CLEAR_IER(uart, EDSSI);
+#endif
+
+ return IRQ_HANDLED;
+}
+#else
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+#endif
/*
* interrupts are disabled on entry
static void bfin_serial_stop_tx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+#ifdef CONFIG_SERIAL_BFIN_DMA
struct circ_buf *xmit = &uart->port.info->xmit;
+#endif
while (!(UART_GET_LSR(uart) & TEMT))
cpu_relax();
static void bfin_serial_start_tx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ struct tty_struct *tty = uart->port.info->port.tty;
+
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
+ /*
+ * To avoid losting RX interrupt, we reset IR function
+ * before sending data.
+ */
+ if (tty->termios->c_line == N_IRDA)
+ bfin_serial_reset_irda(port);
#ifdef CONFIG_SERIAL_BFIN_DMA
if (uart->tx_done)
static void bfin_serial_stop_rx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT)
-#endif
+
UART_CLEAR_IER(uart, ERBFI);
}
{
}
-#ifdef CONFIG_KGDB_UART
-static int kgdb_entry_state;
-
-void kgdb_put_debug_char(int chr)
-{
- struct bfin_serial_port *uart;
-
- if (CONFIG_KGDB_UART_PORT < 0
- || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
- uart = &bfin_serial_ports[0];
- else
- uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-
- while (!(UART_GET_LSR(uart) & THRE)) {
- SSYNC();
- }
-
- UART_CLEAR_DLAB(uart);
- UART_PUT_CHAR(uart, (unsigned char)chr);
- SSYNC();
-}
-
-int kgdb_get_debug_char(void)
-{
- struct bfin_serial_port *uart;
- unsigned char chr;
-
- if (CONFIG_KGDB_UART_PORT < 0
- || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
- uart = &bfin_serial_ports[0];
- else
- uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-
- while(!(UART_GET_LSR(uart) & DR)) {
- SSYNC();
- }
- UART_CLEAR_DLAB(uart);
- chr = UART_GET_CHAR(uart);
- SSYNC();
-
- return chr;
-}
-#endif
#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
# define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold)
#ifdef CONFIG_SERIAL_BFIN_PIO
static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
{
- struct tty_struct *tty = uart->port.info->port.tty;
+ struct tty_struct *tty = NULL;
unsigned int status, ch, flg;
static struct timeval anomaly_start = { .tv_sec = 0 };
ch = UART_GET_CHAR(uart);
uart->port.icount.rx++;
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line == CONFIG_KGDB_UART_PORT) {
- struct pt_regs *regs = get_irq_regs();
- if (uart->port.cons->index == CONFIG_KGDB_UART_PORT && ch == 0x1) { /* Ctrl + A */
- kgdb_breakkey_pressed(regs);
- return;
- } else if (kgdb_entry_state == 0 && ch == '$') {/* connection from KGDB */
- kgdb_entry_state = 1;
- } else if (kgdb_entry_state == 1 && ch == 'q') {
- kgdb_entry_state = 0;
- kgdb_breakkey_pressed(regs);
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ if (kgdb_connected && kgdboc_port_line == uart->port.line)
+ if (ch == 0x3) {/* Ctrl + C */
+ kgdb_breakpoint();
return;
- } else if (ch == 0x3) {/* Ctrl + C */
- kgdb_entry_state = 0;
- kgdb_breakkey_pressed(regs);
- return;
- } else {
- kgdb_entry_state = 0;
}
- }
+
+ if (!uart->port.info || !uart->port.info->port.tty)
+ return;
#endif
+ tty = uart->port.info->port.tty;
if (ANOMALY_05000363) {
/* The BF533 (and BF561) family of processors have a nice anomaly
return;
known_good_char:
+ status &= ~BI;
anomaly_start.tv_sec = 0;
}
}
{
struct circ_buf *xmit = &uart->port.info->xmit;
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
- bfin_serial_stop_tx(&uart->port);
+#ifdef CONFIG_BF54x
+ /* Clear TFI bit */
+ UART_PUT_LSR(uart, TFI);
+#endif
+ UART_CLEAR_IER(uart, ETBEI);
return;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uart->port);
-
- if (uart_circ_empty(xmit))
- bfin_serial_stop_tx(&uart->port);
}
static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
spin_lock(&uart->port.lock);
if (UART_GET_LSR(uart) & THRE)
bfin_serial_tx_chars(uart);
uart->tx_done = 0;
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
uart->tx_count = 0;
uart->tx_done = 1;
else
flg = TTY_NORMAL;
- for (i = uart->rx_dma_buf.tail; i != uart->rx_dma_buf.head; i++) {
+ for (i = uart->rx_dma_buf.tail; ; i++) {
if (i >= UART_XMIT_SIZE)
i = 0;
+ if (i == uart->rx_dma_buf.head)
+ break;
if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
uart_insert_char(&uart->port, status, OE,
uart->rx_dma_buf.buf[i], flg);
void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
{
int x_pos, pos;
+ unsigned long flags;
+
+ spin_lock_irqsave(&uart->port.lock, flags);
uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
}
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+
mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
}
struct bfin_serial_port *uart = dev_id;
struct circ_buf *xmit = &uart->port.info->xmit;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
spin_lock(&uart->port.lock);
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
disable_dma(uart->tx_dma_channel);
spin_lock(&uart->port.lock);
irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
clear_dma_irqstat(uart->rx_dma_channel);
+ bfin_serial_dma_rx_chars(uart);
spin_unlock(&uart->port.lock);
- mod_timer(&(uart->rx_dma_timer), jiffies);
-
return IRQ_HANDLED;
}
#endif
return 0;
}
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->cts_pin < 0)
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-
- if (UART_GET_CTS(uart))
- return TIOCM_DSR | TIOCM_CAR;
- else
-#endif
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->rts_pin < 0)
- return;
-
- if (mctrl & TIOCM_RTS)
- UART_CLEAR_RTS(uart);
- else
- UART_SET_RTS(uart);
-#endif
-}
-
-/*
- * Handle any change of modem status signal since we were last called.
- */
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- unsigned int status;
- struct uart_info *info = uart->port.info;
- struct tty_struct *tty = info->port.tty;
-
- status = bfin_serial_get_mctrl(&uart->port);
- uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
- if (!(status & TIOCM_CTS)) {
- tty->hw_stopped = 1;
- uart->cts_timer.data = (unsigned long)(uart);
- uart->cts_timer.function = (void *)bfin_serial_mctrl_check;
- uart->cts_timer.expires = jiffies + CTS_CHECK_JIFFIES;
- add_timer(&(uart->cts_timer));
- } else {
- tty->hw_stopped = 0;
- }
-#endif
-}
-
-/*
- * Interrupts are always disabled.
- */
static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
add_timer(&(uart->rx_dma_timer));
#else
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
+ kgdboc_break_enabled = 0;
+ else {
+# endif
if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
"BFIN_UART_RX", uart)) {
-# ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT) {
-# endif
printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
return -EBUSY;
-# ifdef CONFIG_KGDB_UART
- }
-# endif
}
if (request_irq
free_irq(uart->port.irq, uart);
return -EBUSY;
}
+
+# ifdef CONFIG_BF54x
+ {
+ unsigned uart_dma_ch_rx, uart_dma_ch_tx;
+
+ switch (uart->port.irq) {
+ case IRQ_UART3_RX:
+ uart_dma_ch_rx = CH_UART3_RX;
+ uart_dma_ch_tx = CH_UART3_TX;
+ break;
+ case IRQ_UART2_RX:
+ uart_dma_ch_rx = CH_UART2_RX;
+ uart_dma_ch_tx = CH_UART2_TX;
+ break;
+ default:
+ uart_dma_ch_rx = uart_dma_ch_tx = 0;
+ break;
+ };
+
+ if (uart_dma_ch_rx &&
+ request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
+ printk(KERN_NOTICE"Fail to attach UART interrupt\n");
+ free_irq(uart->port.irq, uart);
+ free_irq(uart->port.irq + 1, uart);
+ return -EBUSY;
+ }
+ if (uart_dma_ch_tx &&
+ request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
+ printk(KERN_NOTICE "Fail to attach UART interrupt\n");
+ free_dma(uart_dma_ch_rx);
+ free_irq(uart->port.irq, uart);
+ free_irq(uart->port.irq + 1, uart);
+ return -EBUSY;
+ }
+ }
+# endif
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ }
+# endif
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0) {
+ if (request_irq(gpio_to_irq(uart->cts_pin),
+ bfin_serial_mctrl_cts_int,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
+ IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
+ uart->cts_pin = -1;
+ pr_info("Unable to attach BlackFin UART CTS interrupt.\
+ So, disable it.\n");
+ }
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (request_irq(uart->status_irq,
+ bfin_serial_mctrl_cts_int,
+ IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
+ pr_info("Unable to attach BlackFin UART Modem \
+ Status interrupt.\n");
+ }
+
+ if (uart->cts_pin >= 0) {
+ gpio_request(uart->cts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->cts_pin, 1);
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+
+ /* CTS RTS PINs are negative assertive. */
+ UART_PUT_MCR(uart, ACTS);
+ UART_SET_IER(uart, EDSSI);
+#endif
+
UART_SET_IER(uart, ERBFI);
return 0;
}
del_timer(&(uart->rx_dma_timer));
dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
#else
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT)
+#ifdef CONFIG_BF54x
+ switch (uart->port.irq) {
+ case IRQ_UART3_RX:
+ free_dma(CH_UART3_RX);
+ free_dma(CH_UART3_TX);
+ break;
+ case IRQ_UART2_RX:
+ free_dma(CH_UART2_RX);
+ free_dma(CH_UART2_TX);
+ break;
+ default:
+ break;
+ };
#endif
free_irq(uart->port.irq, uart);
free_irq(uart->port.irq+1, uart);
#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0)
+ free_irq(gpio_to_irq(uart->cts_pin), uart);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->cts_pin >= 0)
+ gpio_free(uart->cts_pin);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+ if (UART_GET_IER(uart) && EDSSI)
+ free_irq(uart->status_irq, uart);
+#endif
}
static void
}
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- quot = uart_get_divisor(port, baud);
+ quot = uart_get_divisor(port, baud) - ANOMALY_05000230;
spin_lock_irqsave(&uart->port.lock, flags);
UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
val |= UCEN;
UART_PUT_GCTL(uart, val);
+ /* Port speed changed, update the per-port timeout. */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
spin_unlock_irqrestore(&uart->port.lock, flags);
}
}
}
+static void bfin_serial_reset_irda(struct uart_port *port)
+{
+ int line = port->line;
+ unsigned short val;
+
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val &= ~(IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+ val |= (IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+ while (!(UART_GET_LSR(uart) & THRE))
+ cpu_relax();
+
+ UART_CLEAR_DLAB(uart);
+ UART_PUT_CHAR(uart, (unsigned char)chr);
+}
+
+static int bfin_serial_poll_get_char(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ unsigned char chr;
+
+ while (!(UART_GET_LSR(uart) & DR))
+ cpu_relax();
+
+ UART_CLEAR_DLAB(uart);
+ chr = UART_GET_CHAR(uart);
+
+ return chr;
+}
+#endif
+
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+static void bfin_kgdboc_port_shutdown(struct uart_port *port)
+{
+ if (kgdboc_break_enabled) {
+ kgdboc_break_enabled = 0;
+ bfin_serial_shutdown(port);
+ }
+}
+
+static int bfin_kgdboc_port_startup(struct uart_port *port)
+{
+ kgdboc_port_line = port->line;
+ kgdboc_break_enabled = !bfin_serial_startup(port);
+ return 0;
+}
+#endif
+
static struct uart_ops bfin_serial_pops = {
.tx_empty = bfin_serial_tx_empty,
.set_mctrl = bfin_serial_set_mctrl,
.request_port = bfin_serial_request_port,
.config_port = bfin_serial_config_port,
.verify_port = bfin_serial_verify_port,
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ .kgdboc_port_startup = bfin_kgdboc_port_startup,
+ .kgdboc_port_shutdown = bfin_kgdboc_port_shutdown,
+#endif
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_put_char = bfin_serial_poll_put_char,
+ .poll_get_char = bfin_serial_poll_get_char,
+#endif
};
+static void __init bfin_serial_hw_init(void)
+{
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ peripheral_request(P_UART0_TX, DRIVER_NAME);
+ peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ peripheral_request(P_UART1_TX, DRIVER_NAME);
+ peripheral_request(P_UART1_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART1_RTS, DRIVER_NAME);
+ peripheral_request(P_UART1_CTS, DRIVER_NAME);
+# endif
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART2
+ peripheral_request(P_UART2_TX, DRIVER_NAME);
+ peripheral_request(P_UART2_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART3
+ peripheral_request(P_UART3_TX, DRIVER_NAME);
+ peripheral_request(P_UART3_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART3_RTS, DRIVER_NAME);
+ peripheral_request(P_UART3_CTS, DRIVER_NAME);
+# endif
+#endif
+}
+
static void __init bfin_serial_init_ports(void)
{
static int first = 1;
return;
first = 0;
- for (i = 0; i < nr_ports; i++) {
+ bfin_serial_hw_init();
+
+ for (i = 0; i < nr_active_ports; i++) {
bfin_serial_ports[i].port.uartclk = get_sclk();
+ bfin_serial_ports[i].port.fifosize = BFIN_UART_TX_FIFO_SIZE;
bfin_serial_ports[i].port.ops = &bfin_serial_pops;
bfin_serial_ports[i].port.line = i;
bfin_serial_ports[i].port.iotype = UPIO_MEM;
bfin_serial_resource[i].uart_base_addr;
bfin_serial_ports[i].port.irq =
bfin_serial_resource[i].uart_irq;
+ bfin_serial_ports[i].status_irq =
+ bfin_serial_resource[i].uart_status_irq;
bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
#ifdef CONFIG_SERIAL_BFIN_DMA
bfin_serial_ports[i].tx_done = 1;
bfin_serial_resource[i].uart_rx_dma_channel;
init_timer(&(bfin_serial_ports[i].rx_dma_timer));
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- init_timer(&(bfin_serial_ports[i].cts_timer));
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
bfin_serial_ports[i].cts_pin =
bfin_serial_resource[i].uart_cts_pin;
bfin_serial_ports[i].rts_pin =
bfin_serial_resource[i].uart_rts_pin;
#endif
- bfin_serial_hw_init(&bfin_serial_ports[i]);
}
-
}
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
/*
* If the port was already initialised (eg, by a boot loader),
* try to determine the current setup.
}
pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
}
-#endif
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
static struct uart_driver bfin_serial_reg;
static int __init
bfin_serial_console_setup(struct console *co, char *options)
{
struct bfin_serial_port *uart;
-# ifdef CONFIG_SERIAL_BFIN_CONSOLE
int baud = 57600;
int bits = 8;
int parity = 'n';
-# ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
int flow = 'r';
-# else
+# else
int flow = 'n';
-# endif
# endif
/*
* if so, search for the first available port that does have
* console support.
*/
- if (co->index == -1 || co->index >= nr_ports)
+ if (co->index == -1 || co->index >= nr_active_ports)
co->index = 0;
uart = &bfin_serial_ports[co->index];
-# ifdef CONFIG_SERIAL_BFIN_CONSOLE
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
bfin_serial_console_get_options(uart, &baud, &parity, &bits);
return uart_set_options(&uart->port, co, baud, parity, bits, flow);
-# else
- return 0;
-# endif
}
#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
defined (CONFIG_EARLY_PRINTK) */
bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
{
struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
- int flags = 0;
+ unsigned long flags;
spin_lock_irqsave(&uart->port.lock, flags);
uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
{
bfin_serial_init_ports();
register_console(&bfin_serial_console);
-#ifdef CONFIG_KGDB_UART
- kgdb_entry_state = 0;
- init_kgdb_uart();
-#endif
+
return 0;
}
console_initcall(bfin_serial_rs_console_init);
}
}
-static struct __init console bfin_early_serial_console = {
+static struct __initdata console bfin_early_serial_console = {
.name = "early_BFuart",
.write = early_serial_write,
.device = uart_console_device,
struct bfin_serial_port *uart;
struct ktermios t;
- if (port == -1 || port >= nr_ports)
+ if (port == -1 || port >= nr_active_ports)
port = 0;
bfin_serial_init_ports();
bfin_early_serial_console.index = port;
return &bfin_early_serial_console;
}
-#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
+#endif /* CONFIG_EARLY_PRINTK */
static struct uart_driver bfin_serial_reg = {
.owner = THIS_MODULE,
static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
{
- struct bfin_serial_port *uart = platform_get_drvdata(dev);
+ int i;
- if (uart)
- uart_suspend_port(&bfin_serial_reg, &uart->port);
+ for (i = 0; i < nr_active_ports; i++) {
+ if (bfin_serial_ports[i].port.dev != &dev->dev)
+ continue;
+ uart_suspend_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ }
return 0;
}
static int bfin_serial_resume(struct platform_device *dev)
{
- struct bfin_serial_port *uart = platform_get_drvdata(dev);
+ int i;
- if (uart)
- uart_resume_port(&bfin_serial_reg, &uart->port);
+ for (i = 0; i < nr_active_ports; i++) {
+ if (bfin_serial_ports[i].port.dev != &dev->dev)
+ continue;
+ uart_resume_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ }
return 0;
}
break;
if (i < dev->num_resources) {
- for (i = 0; i < nr_ports; i++, res++) {
+ for (i = 0; i < nr_active_ports; i++, res++) {
if (bfin_serial_ports[i].port.mapbase != res->start)
continue;
bfin_serial_ports[i].port.dev = &dev->dev;
uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
- platform_set_drvdata(dev, &bfin_serial_ports[i]);
}
}
return 0;
}
-static int bfin_serial_remove(struct platform_device *pdev)
+static int bfin_serial_remove(struct platform_device *dev)
{
- struct bfin_serial_port *uart = platform_get_drvdata(pdev);
-
+ int i;
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- gpio_free(uart->cts_pin);
- gpio_free(uart->rts_pin);
+ for (i = 0; i < nr_active_ports; i++) {
+ if (bfin_serial_ports[i].port.dev != &dev->dev)
+ continue;
+ uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ bfin_serial_ports[i].port.dev = NULL;
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+ gpio_free(bfin_serial_ports[i].cts_pin);
+ gpio_free(bfin_serial_ports[i].rts_pin);
#endif
-
- platform_set_drvdata(pdev, NULL);
-
- if (uart)
- uart_remove_one_port(&bfin_serial_reg, &uart->port);
+ }
return 0;
}
static int __init bfin_serial_init(void)
{
int ret;
-#ifdef CONFIG_KGDB_UART
- struct bfin_serial_port *uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
- struct ktermios t;
-#endif
pr_info("Serial: Blackfin serial driver\n");
uart_unregister_driver(&bfin_serial_reg);
}
}
-#ifdef CONFIG_KGDB_UART
- if (uart->port.cons->index != CONFIG_KGDB_UART_PORT) {
- request_irq(uart->port.irq, bfin_serial_rx_int,
- IRQF_DISABLED, "BFIN_UART_RX", uart);
- pr_info("Request irq for kgdb uart port\n");
- UART_SET_IER(uart, ERBFI);
- SSYNC();
- t.c_cflag = CS8|B57600;
- t.c_iflag = 0;
- t.c_oflag = 0;
- t.c_lflag = ICANON;
- t.c_line = CONFIG_KGDB_UART_PORT;
- bfin_serial_set_termios(&uart->port, &t, &t);
- }
-#endif
return ret;
}
uart_unregister_driver(&bfin_serial_reg);
}
+
module_init(bfin_serial_init);
module_exit(bfin_serial_exit);