/* Driver for USB Mass Storage compliant devices
* SCSI layer glue code
*
- * $Id: scsiglue.c,v 1.26 2002/04/22 03:39:43 mdharm Exp $
- *
* Current development and maintenance by:
* (c) 1999-2002 Matthew Dharm (mdharm-usb@one-eyed-alien.net)
*
static int slave_alloc (struct scsi_device *sdev)
{
struct us_data *us = host_to_us(sdev->host);
- struct usb_host_endpoint *bulk_in_ep;
/*
* Set the INQUIRY transfer length to 36. We don't use any of
*/
sdev->inquiry_len = 36;
- /* Scatter-gather buffers (all but the last) must have a length
- * divisible by the bulk maxpacket size. Otherwise a data packet
- * would end up being short, causing a premature end to the data
- * transfer. We'll use the maxpacket value of the bulk-IN pipe
- * to set the SCSI device queue's DMA alignment mask.
+ /* USB has unusual DMA-alignment requirements: Although the
+ * starting address of each scatter-gather element doesn't matter,
+ * the length of each element except the last must be divisible
+ * by the Bulk maxpacket value. There's currently no way to
+ * express this by block-layer constraints, so we'll cop out
+ * and simply require addresses to be aligned at 512-byte
+ * boundaries. This is okay since most block I/O involves
+ * hardware sectors that are multiples of 512 bytes in length,
+ * and since host controllers up through USB 2.0 have maxpacket
+ * values no larger than 512.
+ *
+ * But it doesn't suffice for Wireless USB, where Bulk maxpacket
+ * values can be as large as 2048. To make that work properly
+ * will require changes to the block layer.
*/
- bulk_in_ep = us->pusb_dev->ep_in[usb_pipeendpoint(us->recv_bulk_pipe)];
- blk_queue_update_dma_alignment(sdev->request_queue,
- le16_to_cpu(bulk_in_ep->desc.wMaxPacketSize) - 1);
- /* wMaxPacketSize must be a power of 2 */
+ blk_queue_update_dma_alignment(sdev->request_queue, (512 - 1));
/*
* The UFI spec treates the Peripheral Qualifier bits in an
* while others have trouble with more than 64K. At this time we
* are limiting both to 32K (64 sectores).
*/
- if (us->flags & (US_FL_MAX_SECTORS_64 | US_FL_MAX_SECTORS_MIN)) {
+ if (us->fflags & (US_FL_MAX_SECTORS_64 | US_FL_MAX_SECTORS_MIN)) {
unsigned int max_sectors = 64;
- if (us->flags & US_FL_MAX_SECTORS_MIN)
+ if (us->fflags & US_FL_MAX_SECTORS_MIN)
max_sectors = PAGE_CACHE_SIZE >> 9;
if (sdev->request_queue->max_sectors > max_sectors)
blk_queue_max_sectors(sdev->request_queue,
* majority of devices work fine, but a few still can't
* handle it. The sd driver will simply assume those
* devices are write-enabled. */
- if (us->flags & US_FL_NO_WP_DETECT)
+ if (us->fflags & US_FL_NO_WP_DETECT)
sdev->skip_ms_page_3f = 1;
/* A number of devices have problems with MODE SENSE for
/* Some disks return the total number of blocks in response
* to READ CAPACITY rather than the highest block number.
* If this device makes that mistake, tell the sd driver. */
- if (us->flags & US_FL_FIX_CAPACITY)
+ if (us->fflags & US_FL_FIX_CAPACITY)
sdev->fix_capacity = 1;
/* A few disks have two indistinguishable version, one of
* which reports the correct capacity and the other does not.
* The sd driver has to guess which is the case. */
- if (us->flags & US_FL_CAPACITY_HEURISTICS)
+ if (us->fflags & US_FL_CAPACITY_HEURISTICS)
sdev->guess_capacity = 1;
/* Some devices report a SCSI revision level above 2 but are
/* Some devices choke when they receive a PREVENT-ALLOW MEDIUM
* REMOVAL command, so suppress those commands. */
- if (us->flags & US_FL_NOT_LOCKABLE)
+ if (us->fflags & US_FL_NOT_LOCKABLE)
sdev->lockable = 0;
/* this is to satisfy the compiler, tho I don't think the
}
/* fail the command if we are disconnecting */
- if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) {
+ if (test_bit(US_FLIDX_DISCONNECTING, &us->dflags)) {
US_DEBUGP("Fail command during disconnect\n");
srb->result = DID_NO_CONNECT << 16;
done(srb);
/* enqueue the command and wake up the control thread */
srb->scsi_done = done;
us->srb = srb;
- up(&(us->sema));
+ complete(&us->cmnd_ready);
return 0;
}
* with the reset). Note that we must retain the host lock while
* calling usb_stor_stop_transport(); otherwise it might interfere
* with an auto-reset that begins as soon as we release the lock. */
- set_bit(US_FLIDX_TIMED_OUT, &us->flags);
- if (!test_bit(US_FLIDX_RESETTING, &us->flags)) {
- set_bit(US_FLIDX_ABORTING, &us->flags);
+ set_bit(US_FLIDX_TIMED_OUT, &us->dflags);
+ if (!test_bit(US_FLIDX_RESETTING, &us->dflags)) {
+ set_bit(US_FLIDX_ABORTING, &us->dflags);
usb_stor_stop_transport(us);
}
scsi_unlock(us_to_host(us));
struct Scsi_Host *host = us_to_host(us);
scsi_report_device_reset(host, 0, 0);
- if (us->flags & US_FL_SCM_MULT_TARG) {
+ if (us->fflags & US_FL_SCM_MULT_TARG) {
for (i = 1; i < host->max_id; ++i)
scsi_report_device_reset(host, 0, i);
}
pos += sprintf(pos, " Quirks:");
#define US_FLAG(name, value) \
- if (us->flags & value) pos += sprintf(pos, " " #name);
+ if (us->fflags & value) pos += sprintf(pos, " " #name);
US_DO_ALL_FLAGS
#undef US_FLAG
projects / linux-2.6-omap-h63xx.git / blobdiff