u16 *gpio_config;
unsigned int gpio_config_num;
- unsigned int bus_shift;
-
unsigned int irq_base;
unsigned int gpio_base;
/* All offsets below are specified with this address bus shift */
#define ASIC3_DEFAULT_ADDR_SHIFT 2
-#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_Base + ASIC3_##base##_##reg)
+#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg)
#define ASIC3_GPIO_OFFSET(base, reg) \
- (ASIC3_GPIO_##base##_Base + ASIC3_GPIO_##reg)
+ (ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg)
-#define ASIC3_GPIO_A_Base 0x0000
-#define ASIC3_GPIO_B_Base 0x0100
-#define ASIC3_GPIO_C_Base 0x0200
-#define ASIC3_GPIO_D_Base 0x0300
+#define ASIC3_GPIO_A_BASE 0x0000
+#define ASIC3_GPIO_B_BASE 0x0100
+#define ASIC3_GPIO_C_BASE 0x0200
+#define ASIC3_GPIO_D_BASE 0x0300
#define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4)
#define ASIC3_GPIO_TO_BIT(gpio) ((gpio) - \
(ASIC3_GPIOS_PER_BANK * ((gpio) >> 4)))
#define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio))
-#define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_Base + (((gpio) >> 4) * 0x0100))
-#define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_Base + ((bank) * 0x100))
-
-#define ASIC3_GPIO_Mask 0x00 /* R/W 0:don't mask */
-#define ASIC3_GPIO_Direction 0x04 /* R/W 0:input */
-#define ASIC3_GPIO_Out 0x08 /* R/W 0:output low */
-#define ASIC3_GPIO_TriggerType 0x0c /* R/W 0:level */
-#define ASIC3_GPIO_EdgeTrigger 0x10 /* R/W 0:falling */
-#define ASIC3_GPIO_LevelTrigger 0x14 /* R/W 0:low level detect */
-#define ASIC3_GPIO_SleepMask 0x18 /* R/W 0:don't mask in sleep mode */
-#define ASIC3_GPIO_SleepOut 0x1c /* R/W level 0:low in sleep mode */
-#define ASIC3_GPIO_BattFaultOut 0x20 /* R/W level 0:low in batt_fault */
-#define ASIC3_GPIO_IntStatus 0x24 /* R/W 0:none, 1:detect */
-#define ASIC3_GPIO_AltFunction 0x28 /* R/W 1:LED register control */
-#define ASIC3_GPIO_SleepConf 0x2c /*
+#define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100))
+#define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100))
+
+#define ASIC3_GPIO_MASK 0x00 /* R/W 0:don't mask */
+#define ASIC3_GPIO_DIRECTION 0x04 /* R/W 0:input */
+#define ASIC3_GPIO_OUT 0x08 /* R/W 0:output low */
+#define ASIC3_GPIO_TRIGGER_TYPE 0x0c /* R/W 0:level */
+#define ASIC3_GPIO_EDGE_TRIGGER 0x10 /* R/W 0:falling */
+#define ASIC3_GPIO_LEVEL_TRIGGER 0x14 /* R/W 0:low level detect */
+#define ASIC3_GPIO_SLEEP_MASK 0x18 /* R/W 0:don't mask in sleep mode */
+#define ASIC3_GPIO_SLEEP_OUT 0x1c /* R/W level 0:low in sleep mode */
+#define ASIC3_GPIO_BAT_FAULT_OUT 0x20 /* R/W level 0:low in batt_fault */
+#define ASIC3_GPIO_INT_STATUS 0x24 /* R/W 0:none, 1:detect */
+#define ASIC3_GPIO_ALT_FUNCTION 0x28 /* R/W 1:LED register control */
+#define ASIC3_GPIO_SLEEP_CONF 0x2c /*
* R/W bit 1: autosleep
* 0: disable gposlpout in normal mode,
* enable gposlpout in sleep mode.
*/
-#define ASIC3_GPIO_Status 0x30 /* R Pin status */
+#define ASIC3_GPIO_STATUS 0x30 /* R Pin status */
/*
* ASIC3 GPIO config
#define ASIC3_CONFIG_GPIO_DEFAULT_OUT(gpio, init) \
ASIC3_CONFIG_GPIO((gpio), 0, 1, (init))
+/*
+ * Alternate functions
+ */
+#define ASIC3_GPIOA11_PWM0 ASIC3_CONFIG_GPIO(11, 1, 1, 0)
+#define ASIC3_GPIOA12_PWM1 ASIC3_CONFIG_GPIO(12, 1, 1, 0)
+#define ASIC3_GPIOA15_CONTROL_CX ASIC3_CONFIG_GPIO(15, 1, 1, 0)
+#define ASIC3_GPIOC0_LED0 ASIC3_CONFIG_GPIO(32, 1, 1, 0)
+#define ASIC3_GPIOC1_LED1 ASIC3_CONFIG_GPIO(33, 1, 1, 0)
+#define ASIC3_GPIOC2_LED2 ASIC3_CONFIG_GPIO(34, 1, 1, 0)
+#define ASIC3_GPIOC3_SPI_RXD ASIC3_CONFIG_GPIO(35, 1, 0, 0)
+#define ASIC3_GPIOC4_CF_nCD ASIC3_CONFIG_GPIO(36, 1, 0, 0)
+#define ASIC3_GPIOC4_SPI_TXD ASIC3_CONFIG_GPIO(36, 1, 1, 0)
+#define ASIC3_GPIOC5_SPI_CLK ASIC3_CONFIG_GPIO(37, 1, 1, 0)
+#define ASIC3_GPIOC5_nCIOW ASIC3_CONFIG_GPIO(37, 1, 1, 0)
+#define ASIC3_GPIOC6_nCIOR ASIC3_CONFIG_GPIO(38, 1, 1, 0)
+#define ASIC3_GPIOC7_nPCE_1 ASIC3_CONFIG_GPIO(39, 1, 0, 0)
+#define ASIC3_GPIOC8_nPCE_2 ASIC3_CONFIG_GPIO(40, 1, 0, 0)
+#define ASIC3_GPIOC9_nPOE ASIC3_CONFIG_GPIO(41, 1, 0, 0)
+#define ASIC3_GPIOC10_nPWE ASIC3_CONFIG_GPIO(42, 1, 0, 0)
+#define ASIC3_GPIOC11_PSKTSEL ASIC3_CONFIG_GPIO(43, 1, 0, 0)
+#define ASIC3_GPIOC12_nPREG ASIC3_CONFIG_GPIO(44, 1, 0, 0)
+#define ASIC3_GPIOC13_nPWAIT ASIC3_CONFIG_GPIO(45, 1, 1, 0)
+#define ASIC3_GPIOC14_nPIOIS16 ASIC3_CONFIG_GPIO(46, 1, 1, 0)
+#define ASIC3_GPIOC15_nPIOR ASIC3_CONFIG_GPIO(47, 1, 0, 0)
+#define ASIC3_GPIOD11_nCIOIS16 ASIC3_CONFIG_GPIO(59, 1, 0, 0)
+#define ASIC3_GPIOD12_nCWAIT ASIC3_CONFIG_GPIO(60, 1, 0, 0)
+#define ASIC3_GPIOD15_nPIOW ASIC3_CONFIG_GPIO(63, 1, 0, 0)
+
+
#define ASIC3_SPI_Base 0x0400
#define ASIC3_SPI_Control 0x0000
#define ASIC3_SPI_TxData 0x0004
#define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */
#define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */
-#define ASIC3_CLOCK_Base 0x0A00
+#define ASIC3_CLOCK_BASE 0x0A00
#define ASIC3_CLOCK_CDEX 0x00
#define ASIC3_CLOCK_SEL 0x04
#define CLOCK_SEL_CX (1 << 2)
-#define ASIC3_INTR_Base 0x0B00
+#define ASIC3_INTR_BASE 0x0B00
-#define ASIC3_INTR_IntMask 0x00 /* Interrupt mask control */
-#define ASIC3_INTR_PIntStat 0x04 /* Peripheral interrupt status */
-#define ASIC3_INTR_IntCPS 0x08 /* Interrupt timer clock pre-scale */
-#define ASIC3_INTR_IntTBS 0x0c /* Interrupt timer set */
+#define ASIC3_INTR_INT_MASK 0x00 /* Interrupt mask control */
+#define ASIC3_INTR_P_INT_STAT 0x04 /* Peripheral interrupt status */
+#define ASIC3_INTR_INT_CPS 0x08 /* Interrupt timer clock pre-scale */
+#define ASIC3_INTR_INT_TBS 0x0c /* Interrupt timer set */
#define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */
#define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */
#define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */
/*********************************************
- * The Onewire interface registers
- *
- * OWM_CMD
- * OWM_DAT
- * OWM_INTR
- * OWM_INTEN
- * OWM_CLKDIV
+ * The Onewire interface (DS1WM) is handled
+ * by the ds1wm driver.
*
*********************************************/
-#define ASIC3_OWM_Base 0xC00
-
-#define ASIC3_OWM_CMD 0x00
-#define ASIC3_OWM_DAT 0x04
-#define ASIC3_OWM_INTR 0x08
-#define ASIC3_OWM_INTEN 0x0C
-#define ASIC3_OWM_CLKDIV 0x10
-
-#define ASIC3_OWM_CMD_ONEWR (1 << 0)
-#define ASIC3_OWM_CMD_SRA (1 << 1)
-#define ASIC3_OWM_CMD_DQO (1 << 2)
-#define ASIC3_OWM_CMD_DQI (1 << 3)
-
-#define ASIC3_OWM_INTR_PD (1 << 0)
-#define ASIC3_OWM_INTR_PDR (1 << 1)
-#define ASIC3_OWM_INTR_TBE (1 << 2)
-#define ASIC3_OWM_INTR_TEMP (1 << 3)
-#define ASIC3_OWM_INTR_RBF (1 << 4)
-
-#define ASIC3_OWM_INTEN_EPD (1 << 0)
-#define ASIC3_OWM_INTEN_IAS (1 << 1)
-#define ASIC3_OWM_INTEN_ETBE (1 << 2)
-#define ASIC3_OWM_INTEN_ETMT (1 << 3)
-#define ASIC3_OWM_INTEN_ERBF (1 << 4)
-
-#define ASIC3_OWM_CLKDIV_PRE (3 << 0) /* two bits wide at bit 0 */
-#define ASIC3_OWM_CLKDIV_DIV (7 << 2) /* 3 bits wide at bit 2 */
-
+#define ASIC3_OWM_BASE 0xC00
/*****************************************************************************
* The SD configuration registers are at a completely different location
#define ASIC3_SDIO_CTRL_LEDCtrl 0x7C
#define ASIC3_SDIO_CTRL_SoftwareReset 0x1C0
-#define ASIC3_MAP_SIZE 0x2000
+#define ASIC3_MAP_SIZE_32BIT 0x2000
+#define ASIC3_MAP_SIZE_16BIT 0x1000
#endif /* __ASIC3_H__ */
projects / linux-2.6-omap-h63xx.git / blobdiff