X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;ds=sidebyside;f=include%2Flinux%2Fregulator%2Fdriver.h;h=6e957aae7629f33fe2cd4e7dc1f1ecb70a8552e4;hb=853116a10544206b6b2cf42ebc9d78fba2668888;hp=e37d80561985df64f9497e0aa26a4718e5c24ab5;hpb=55fa518867978e1f5fd8353098f80d125ac734d7;p=linux-2.6-omap-h63xx.git

diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index e37d8056198..6e957aae762 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -21,10 +21,47 @@
 struct regulator_dev;
 struct regulator_init_data;
 
+enum regulator_status {
+	REGULATOR_STATUS_OFF,
+	REGULATOR_STATUS_ON,
+	REGULATOR_STATUS_ERROR,
+	/* fast/normal/idle/standby are flavors of "on" */
+	REGULATOR_STATUS_FAST,
+	REGULATOR_STATUS_NORMAL,
+	REGULATOR_STATUS_IDLE,
+	REGULATOR_STATUS_STANDBY,
+};
+
 /**
  * struct regulator_ops - regulator operations.
  *
- * This struct describes regulator operations.
+ * This struct describes regulator operations which can be implemented by
+ * regulator chip drivers.
+ *
+ * @enable: Enable the regulator.
+ * @disable: Disable the regulator.
+ * @is_enabled: Return 1 if the regulator is enabled, 0 otherwise.
+ *
+ * @set_voltage: Set the voltage for the regulator within the range specified.
+ *               The driver should select the voltage closest to min_uV.
+ * @get_voltage: Return the currently configured voltage for the regulator.
+ *
+ * @set_current_limit: Configure a limit for a current-limited regulator.
+ * @get_current_limit: Get the limit for a current-limited regulator.
+ *
+ * @set_mode: Set the operating mode for the regulator.
+ * @get_mode: Get the current operating mode for the regulator.
+ * @get_optimum_mode: Get the most efficient operating mode for the regulator
+ *                    when running with the specified parameters.
+ *
+ * @set_suspend_voltage: Set the voltage for the regulator when the system
+ *                       is suspended.
+ * @set_suspend_enable: Mark the regulator as enabled when the system is
+ *                      suspended.
+ * @set_suspend_disable: Mark the regulator as disabled when the system is
+ *                       suspended.
+ * @set_suspend_mode: Set the operating mode for the regulator when the
+ *                    system is suspended.
  */
 struct regulator_ops {
 
@@ -46,6 +83,12 @@ struct regulator_ops {
 	int (*set_mode) (struct regulator_dev *, unsigned int mode);
 	unsigned int (*get_mode) (struct regulator_dev *);
 
+	/* report regulator status ... most other accessors report
+	 * control inputs, this reports results of combining inputs
+	 * from Linux (and other sources) with the actual load.
+	 */
+	int (*get_status)(struct regulator_dev *);
+
 	/* get most efficient regulator operating mode for load */
 	unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV,
 					  int output_uV, int load_uA);
@@ -75,6 +118,15 @@ enum regulator_type {
 /**
  * struct regulator_desc - Regulator descriptor
  *
+ * Each regulator registered with the core is described with a structure of
+ * this type.
+ *
+ * @name: Identifying name for the regulator.
+ * @id: Numerical identifier for the regulator.
+ * @ops: Regulator operations table.
+ * @irq: Interrupt number for the regulator.
+ * @type: Indicates if the regulator is a voltage or current regulator.
+ * @owner: Module providing the regulator, used for refcounting.
  */
 struct regulator_desc {
 	const char *name;