X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;f=arch%2Farm%2Fmach-at91%2Fboard-sam9g20ek.c;h=81439fe6fb3d7bc368ce1656870aa1d476d98b67;hb=e4f722fa42537bcb0ff14322a57dc3870d093cab;hp=b588ead14d68a4cb569f1ca8384c166a32bffb33;hpb=2be508d847392e431759e370d21cea9412848758;p=linux-2.6-omap-h63xx.git

diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index b588ead14d6..81439fe6fb3 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -37,7 +37,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -156,6 +158,38 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 7,
+	.write_cycle		= 7,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 3,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -195,7 +229,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */