X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;f=drivers%2Fnet%2Fau1000_eth.c;h=3634b5fd791964d88bf42bd3785402b79e0fc44a;hb=f34ebab68a8e3c80ff4364f4c61734faec5161d4;hp=b46c5d8a77bdca845398d26a90d97d02f8ee60d6;hpb=f4921aff5b174349bc36551f142a5dbac782ea3f;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/net/au1000_eth.c b/drivers/net/au1000_eth.c
index b46c5d8a77b..3634b5fd791 100644
--- a/drivers/net/au1000_eth.c
+++ b/drivers/net/au1000_eth.c
@@ -54,13 +54,16 @@
 #include <linux/delay.h>
 #include <linux/crc32.h>
 #include <linux/phy.h>
+
+#include <asm/cpu.h>
 #include <asm/mipsregs.h>
 #include <asm/irq.h>
 #include <asm/io.h>
 #include <asm/processor.h>
 
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/cpu.h>
+#include <au1000.h>
+#include <prom.h>
+
 #include "au1000_eth.h"
 
 #ifdef AU1000_ETH_DEBUG
@@ -96,11 +99,6 @@ static void mdio_write(struct net_device *, int, int, u16);
 static void au1000_adjust_link(struct net_device *);
 static void enable_mac(struct net_device *, int);
 
-// externs
-extern int get_ethernet_addr(char *ethernet_addr);
-extern void str2eaddr(unsigned char *ea, unsigned char *str);
-extern char * prom_getcmdline(void);
-
 /*
  * Theory of operation
  *
@@ -544,7 +542,7 @@ static struct {
 static int num_ifs;
 
 /*
- * Setup the base address and interupt of the Au1xxx ethernet macs
+ * Setup the base address and interrupt of the Au1xxx ethernet macs
  * based on cpu type and whether the interface is enabled in sys_pinfunc
  * register. The last interface is enabled if SYS_PF_NI2 (bit 4) is 0.
  */
@@ -619,7 +617,6 @@ static struct net_device * au1000_probe(int port_num)
 	struct au1000_private *aup = NULL;
 	struct net_device *dev = NULL;
 	db_dest_t *pDB, *pDBfree;
-	char *pmac, *argptr;
 	char ethaddr[6];
 	int irq, i, err;
 	u32 base, macen;
@@ -677,21 +674,12 @@ static struct net_device * au1000_probe(int port_num)
 	au_macs[port_num] = aup;
 
 	if (port_num == 0) {
-		/* Check the environment variables first */
-		if (get_ethernet_addr(ethaddr) == 0)
+		if (prom_get_ethernet_addr(ethaddr) == 0)
 			memcpy(au1000_mac_addr, ethaddr, sizeof(au1000_mac_addr));
 		else {
-			/* Check command line */
-			argptr = prom_getcmdline();
-			if ((pmac = strstr(argptr, "ethaddr=")) == NULL)
-				printk(KERN_INFO "%s: No MAC address found\n",
-						 dev->name);
+			printk(KERN_INFO "%s: No MAC address found\n",
+					 dev->name);
 				/* Use the hard coded MAC addresses */
-			else {
-				str2eaddr(ethaddr, pmac + strlen("ethaddr="));
-				memcpy(au1000_mac_addr, ethaddr,
-				       sizeof(au1000_mac_addr));
-			}
 		}
 
 		setup_hw_rings(aup, MAC0_RX_DMA_ADDR, MAC0_TX_DMA_ADDR);
@@ -713,7 +701,7 @@ static struct net_device * au1000_probe(int port_num)
 	aup->mii_bus.write = mdiobus_write;
 	aup->mii_bus.reset = mdiobus_reset;
 	aup->mii_bus.name = "au1000_eth_mii";
-	aup->mii_bus.id = aup->mac_id;
+	snprintf(aup->mii_bus.id, MII_BUS_ID_SIZE, "%x", aup->mac_id);
 	aup->mii_bus.irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
 	for(i = 0; i < PHY_MAX_ADDR; ++i)
 		aup->mii_bus.irq[i] = PHY_POLL;
@@ -721,11 +709,11 @@ static struct net_device * au1000_probe(int port_num)
 	/* if known, set corresponding PHY IRQs */
 #if defined(AU1XXX_PHY_STATIC_CONFIG)
 # if defined(AU1XXX_PHY0_IRQ)
-	if (AU1XXX_PHY0_BUSID == aup->mii_bus.id)
+	if (AU1XXX_PHY0_BUSID == aup->mac_id)
 		aup->mii_bus.irq[AU1XXX_PHY0_ADDR] = AU1XXX_PHY0_IRQ;
 # endif
 # if defined(AU1XXX_PHY1_IRQ)
-	if (AU1XXX_PHY1_BUSID == aup->mii_bus.id)
+	if (AU1XXX_PHY1_BUSID == aup->mac_id)
 		aup->mii_bus.irq[AU1XXX_PHY1_ADDR] = AU1XXX_PHY1_IRQ;
 # endif
 #endif