X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;f=drivers%2Fscsi%2Fsata_uli.c;h=9c06f2abe7f7950f8bd0a945cb694cc2dca399a5;hb=1a04392bd6439876b1552793389cbb5be356ea54;hp=eb202a73bc0edb9b79a972cd092ac0dc606c21be;hpb=8a60a07129fad60bba779a2a4038c7518b167fc7;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
index eb202a73bc0..9c06f2abe7f 100644
--- a/drivers/scsi/sata_uli.c
+++ b/drivers/scsi/sata_uli.c
@@ -1,21 +1,26 @@
 /*
  *  sata_uli.c - ULi Electronics SATA
  *
- *  The contents of this file are subject to the Open
- *  Software License version 1.1 that can be found at
- *  http://www.opensource.org/licenses/osl-1.1.txt and is included herein
- *  by reference.
  *
- *  Alternatively, the contents of this file may be used under the terms
- *  of the GNU General Public License version 2 (the "GPL") as distributed
- *  in the kernel source COPYING file, in which case the provisions of
- *  the GPL are applicable instead of the above.  If you wish to allow
- *  the use of your version of this file only under the terms of the
- *  GPL and not to allow others to use your version of this file under
- *  the OSL, indicate your decision by deleting the provisions above and
- *  replace them with the notice and other provisions required by the GPL.
- *  If you do not delete the provisions above, a recipient may use your
- *  version of this file under either the OSL or the GPL.
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ *  libata documentation is available via 'make {ps|pdf}docs',
+ *  as Documentation/DocBook/libata.*
+ *
+ *  Hardware documentation available under NDA.
  *
  */
 
@@ -120,8 +125,8 @@ static struct ata_port_info uli_port_info = {
 	.sht            = &uli_sht,
 	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
 			  ATA_FLAG_NO_LEGACY,
-	.pio_mask       = 0x03,		//support pio mode 4 (FIXME)
-	.udma_mask      = 0x7f,		//support udma mode 6
+	.pio_mask       = 0x1f,		/* pio0-4 */
+	.udma_mask      = 0x7f,		/* udma0-6 */
 	.port_ops       = &uli_ops,
 };
 
@@ -171,18 +176,6 @@ static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
 	uli_scr_cfg_write(ap, sc_reg, val);
 }
 
-/* move to PCI layer, integrate w/ MSI stuff */
-static void pci_enable_intx(struct pci_dev *pdev)
-{
-	u16 pci_command;
-
-	pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
-	if (pci_command & PCI_COMMAND_INTX_DISABLE) {
-		pci_command &= ~PCI_COMMAND_INTX_DISABLE;
-		pci_write_config_word(pdev, PCI_COMMAND, pci_command);
-	}
-}
-
 static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	struct ata_probe_ent *probe_ent;
@@ -209,7 +202,7 @@ static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 		goto err_out_regions;
 
 	ppi = &uli_port_info;
-	probe_ent = ata_pci_init_native_mode(pdev, &ppi);
+	probe_ent = ata_pci_init_native_mode(pdev, &ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
 	if (!probe_ent) {
 		rc = -ENOMEM;
 		goto err_out_regions;
@@ -255,7 +248,7 @@ static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 
 	pci_set_master(pdev);
-	pci_enable_intx(pdev);
+	pci_intx(pdev, 1);
 
 	/* FIXME: check ata_device_add return value */
 	ata_device_add(probe_ent);