X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;f=drivers%2Fserial%2Fserial_lh7a40x.c;h=eb18d429752d2d40458eb47234f3fd4649bf39fd;hb=a9cccd34372f7075e8746395609bc78f0fbaf204;hp=aa521b8e0d4e3a06a3c0c53ca7929a72d0b96763;hpb=95d465fd750897ab32462a6702fbfe1b122cbbc0;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/serial/serial_lh7a40x.c b/drivers/serial/serial_lh7a40x.c
index aa521b8e0d4..eb18d429752 100644
--- a/drivers/serial/serial_lh7a40x.c
+++ b/drivers/serial/serial_lh7a40x.c
@@ -27,7 +27,6 @@
  *
  */
 
-#include <linux/config.h>
 
 #if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
 #define SUPPORT_SYSRQ
@@ -136,23 +135,19 @@ static void lh7a40xuart_enable_ms (struct uart_port* port)
 	BIT_SET (port, UART_R_INTEN, ModemInt);
 }
 
-static void
-#ifdef SUPPORT_SYSRQ
-lh7a40xuart_rx_chars (struct uart_port* port, struct pt_regs* regs)
-#else
-lh7a40xuart_rx_chars (struct uart_port* port)
-#endif
+static void lh7a40xuart_rx_chars (struct uart_port* port)
 {
 	struct tty_struct* tty = port->info->tty;
 	int cbRxMax = 256;	/* (Gross) limit on receive */
-	unsigned int data, flag;/* Received data and status */
+	unsigned int data;	/* Received data and status */
+	unsigned int flag;
 
 	while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) {
 		data = UR (port, UART_R_DATA);
 		flag = TTY_NORMAL;
 		++port->icount.rx;
 
-		if (unlikely(data & RxError)) {	/* Quick check, short-circuit */
+		if (unlikely(data & RxError)) {
 			if (data & RxBreak) {
 				data &= ~(RxFramingError | RxParityError);
 				++port->icount.brk;
@@ -177,7 +172,7 @@ lh7a40xuart_rx_chars (struct uart_port* port)
 				flag = TTY_FRAME;
 		}
 
-		if (uart_handle_sysrq_char (port, (unsigned char) data, regs))
+		if (uart_handle_sysrq_char (port, (unsigned char) data))
 			continue;
 
 		uart_insert_char(port, data, RxOverrunError, data, flag);
@@ -248,8 +243,7 @@ static void lh7a40xuart_modem_status (struct uart_port* port)
 	wake_up_interruptible (&port->info->delta_msr_wait);
 }
 
-static irqreturn_t lh7a40xuart_int (int irq, void* dev_id,
-				    struct pt_regs* regs)
+static irqreturn_t lh7a40xuart_int (int irq, void* dev_id)
 {
 	struct uart_port* port = dev_id;
 	unsigned int cLoopLimit = ISR_LOOP_LIMIT;
@@ -258,11 +252,7 @@ static irqreturn_t lh7a40xuart_int (int irq, void* dev_id,
 
 	do {
 		if (isr & (RxInt | RxTimeoutInt))
-#ifdef SUPPORT_SYSRQ
-			lh7a40xuart_rx_chars(port, regs);
-#else
 			lh7a40xuart_rx_chars(port);
-#endif
 		if (isr & ModemInt)
 			lh7a40xuart_modem_status (port);
 		if (isr & TxInt)
@@ -303,7 +293,7 @@ static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl)
 	/* Note, kernel appears to be setting DTR and RTS on console. */
 
 	/* *** FIXME: this deserves more work.  There's some work in
-               tracing all of the IO pins. */
+	       tracing all of the IO pins. */
 #if 0
 	if( port->mapbase == UART1_PHYS) {
 		gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS);
@@ -358,8 +348,8 @@ static void lh7a40xuart_shutdown (struct uart_port* port)
 }
 
 static void lh7a40xuart_set_termios (struct uart_port* port,
-				     struct termios* termios,
-				     struct termios* old)
+				     struct ktermios* termios,
+				     struct ktermios* old)
 {
 	unsigned int con;
 	unsigned int inten;
@@ -662,9 +652,13 @@ static int __init lh7a40xuart_init(void)
 	if (ret == 0) {
 		int i;
 
-		for (i = 0; i < DEV_NR; i++)
+		for (i = 0; i < DEV_NR; i++) {
+			/* UART3, when used, requires GPIO pin reallocation */
+			if (lh7a40x_ports[i].port.mapbase == UART3_PHYS)
+				GPIO_PINMUX |= 1<<3;
 			uart_add_one_port (&lh7a40x_reg,
 					   &lh7a40x_ports[i].port);
+		}
 	}
 	return ret;
 }