X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;f=drivers%2Fspi%2FKconfig;h=9052f4c3493b3f9c3c567fcd4156d6e4127f1c69;hb=58a3bb59973e33a428d72fa530a3d1d81feb0e8f;hp=23334c8bc4c75e5c29fcf2415267d3c00397425c;hpb=f0cd91a68acdc9b49d7f6738b514a426da627649;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 23334c8bc4c..9052f4c3493 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -16,7 +16,7 @@ config SPI
 	  controller and a chipselect.  Most SPI slaves don't support
 	  dynamic device discovery; some are even write-only or read-only.
 
-	  SPI is widely used by microcontollers to talk with sensors,
+	  SPI is widely used by microcontrollers to talk with sensors,
 	  eeprom and flash memory, codecs and various other controller
 	  chips, analog to digital (and d-to-a) converters, and more.
 	  MMC and SD cards can be accessed using SPI protocol; and for
@@ -75,6 +75,13 @@ config SPI_BUTTERFLY
 	  inexpensive battery powered microcontroller evaluation board.
 	  This same cable can be used to flash new firmware.
 
+config SPI_IMX
+	tristate "Freescale iMX SPI controller"
+	depends on SPI_MASTER && ARCH_IMX && EXPERIMENTAL
+	help
+	  This enables using the Freescale iMX SPI controller in master
+	  mode.
+
 config SPI_MPC83xx
 	tristate "Freescale MPC83xx SPI controller"
 	depends on SPI_MASTER && PPC_83xx && EXPERIMENTAL
@@ -87,6 +94,14 @@ config SPI_MPC83xx
 	  family of PowerPC processors.  The MPC83xx uses a simple set of shift
 	  registers for data (opposed to the CPM based descriptor model).
 
+config SPI_OMAP_UWIRE
+	tristate "OMAP1 MicroWire"
+	depends on SPI_MASTER && ARCH_OMAP1
+	select SPI_BITBANG
+	help
+	  This hooks up to the MicroWire controller on OMAP1 chips.
+
+
 config SPI_PXA2XX
 	tristate "PXA2xx SSP SPI master"
 	depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL
@@ -95,6 +110,12 @@ config SPI_PXA2XX
 	  The driver can be configured to use any SSP port and additional
 	  documentation can be found a Documentation/spi/pxa2xx.
 
+config SPI_S3C24XX
+	tristate "Samsung S3C24XX series SPI"
+	depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL
+	help
+	  SPI driver for Samsung S3C24XX series ARM SoCs
+
 config SPI_S3C24XX_GPIO
 	tristate "Samsung S3C24XX series SPI by GPIO"
 	depends on SPI_MASTER && ARCH_S3C2410 && SPI_BITBANG && EXPERIMENTAL
@@ -107,13 +128,6 @@ config SPI_S3C24XX_GPIO
 # Add new SPI master controllers in alphabetical order above this line
 #
 
-
-config SPI_S3C24XX
-	tristate "Samsung S3C24XX series SPI"
-	depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL
-	help
-	  SPI driver for Samsung S3C24XX series ARM SoCs
-
 #
 # There are lots of SPI device types, with sensors and memory
 # being probably the most widely used ones.
@@ -121,6 +135,16 @@ config SPI_S3C24XX
 comment "SPI Protocol Masters"
 	depends on SPI_MASTER
 
+config SPI_AT25
+	tristate "SPI EEPROMs from most vendors"
+	depends on SPI_MASTER && SYSFS
+	help
+	  Enable this driver to get read/write support to most SPI EEPROMs,
+	  after you configure the board init code to know about each eeprom
+	  on your target board.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called at25.
 
 #
 # Add new SPI protocol masters in alphabetical order above this line