X-Git-Url: http://pilppa.org/gitweb/?a=blobdiff_plain;f=drivers%2Fw1%2FKconfig;h=8b3d0f0c7bd540b697ae4960a1734cfb5a4ea221;hb=d120cfb544ed6161b9d32fb6c4648c471807ee6b;hp=9a1e00dd3e02a45363911ce7ee04e3a680b87796;hpb=5d54e69c68c05b162a56f9914cae72afd7e6f40a;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/w1/Kconfig b/drivers/w1/Kconfig
index 9a1e00dd3e0..8b3d0f0c7bd 100644
--- a/drivers/w1/Kconfig
+++ b/drivers/w1/Kconfig
@@ -2,8 +2,9 @@ menu "Dallas's 1-wire bus"
 
 config W1
 	tristate "Dallas's 1-wire support"
+	depends on CONNECTOR
 	---help---
-	  Dallas's 1-wire bus is usefull to connect slow 1-pin devices
+	  Dallas' 1-wire bus is useful to connect slow 1-pin devices
 	  such as iButtons and thermal sensors.
 
 	  If you want W1 support, you should say Y here.
@@ -11,63 +12,19 @@ config W1
 	  This W1 support can also be built as a module.  If so, the module
 	  will be called wire.ko.
 
-config W1_MATROX
-	tristate "Matrox G400 transport layer for 1-wire"
-	depends on W1 && PCI
-	help
-	  Say Y here if you want to communicate with your 1-wire devices
-	  using Matrox's G400 GPIO pins.
-
-	  This support is also available as a module.  If so, the module
-	  will be called matrox_w1.ko.
-
-config W1_DS9490
-	tristate "DS9490R transport layer driver"
-	depends on W1 && USB
-	help
-	  Say Y here if you want to have a driver for DS9490R UWB <-> W1 bridge.
-
-	  This support is also available as a module.  If so, the module
-	  will be called ds9490r.ko.
-
-config W1_DS9490_BRIDGE
-	tristate "DS9490R USB <-> W1 transport layer for 1-wire"
-	depends on W1_DS9490
-	help
-	  Say Y here if you want to communicate with your 1-wire devices
-	  using DS9490R USB bridge.
-
-	  This support is also available as a module.  If so, the module
-	  will be called ds_w1_bridge.ko.
-
-config W1_THERM
-	tristate "Thermal family implementation"
-	depends on W1
-	help
-	  Say Y here if you want to connect 1-wire thermal sensors to you
-	  wire.
-
-config W1_SMEM
-	tristate "Simple 64bit memory family implementation"
-	depends on W1
-	help
-	  Say Y here if you want to connect 1-wire
-	  simple 64bit memory rom(ds2401/ds2411/ds1990*) to you wire.
-
-config W1_DS2433
-	tristate "4kb EEPROM family support (DS2433)"
-	depends on W1
-	help
-	  Say Y here if you want to use a 1-wire
-	  4kb EEPROM family device (DS2433).
-
-config W1_DS2433_CRC
-	bool "Protect DS2433 data with a CRC16"
-	depends on W1_DS2433
-	select CRC16
-	help
-	  Say Y here to protect DS2433 data with a CRC16.
-	  Each block has 30 bytes of data and a two byte CRC16.
-	  Full block writes are only allowed if the CRC is valid.
+config W1_CON
+	depends on CONNECTOR && W1
+	bool "Userspace communication over connector"
+	default y
+	--- help ---
+	  This allows to communicate with userspace using connector [Documentation/connector].
+	  There are three types of messages between w1 core and userspace:
+	  1. Events. They are generated each time new master or slave device found
+		either due to automatic or requested search.
+	  2. Userspace commands. Includes read/write and search/alarm search comamnds.
+	  3. Replies to userspace commands.
+
+source drivers/w1/masters/Kconfig
+source drivers/w1/slaves/Kconfig
 
 endmenu