udelay(300);
 
-       while (limit--) {
+       while (--limit) {
                val = phy_read(phy, MII_BMCR);
                if (val >= 0 && (val & BMCR_RESET) == 0)
                        break;
 
        udelay(300);
 
-       while (limit--) {
+       while (--limit) {
                val = gpcs_phy_read(phy, MII_BMCR);
                if (val >= 0 && (val & BMCR_RESET) == 0)
                        break;
 
 
        /* make sure EEPROM has finished loading before setting GPIO_CFG */
        timeout=1000;
-       while ( timeout-- && (SMC_GET_E2P_CMD(lp) & E2P_CMD_EPC_BUSY_)) {
+       while (--timeout && (SMC_GET_E2P_CMD(lp) & E2P_CMD_EPC_BUSY_))
                udelay(10);
-       }
+
        if (timeout == 0){
                PRINTK("%s: smc911x_reset timeout waiting for EEPROM busy\n", dev->name);
                return;
 
 static void smsc9420_stop_tx(struct smsc9420_pdata *pd)
 {
        u32 dmac_control, mac_cr, dma_intr_ena;
-       int timeOut = 1000;
+       int timeout = 1000;
 
        /* disable TX DMAC */
        dmac_control = smsc9420_reg_read(pd, DMAC_CONTROL);
        smsc9420_reg_write(pd, DMAC_CONTROL, dmac_control);
 
        /* Wait max 10ms for transmit process to stop */
-       while (timeOut--) {
+       while (--timeout) {
                if (smsc9420_reg_read(pd, DMAC_STATUS) & DMAC_STS_TS_)
                        break;
                udelay(10);
        }
 
-       if (!timeOut)
+       if (!timeout)
                smsc_warn(IFDOWN, "TX DMAC failed to stop");
 
        /* ACK Tx DMAC stop bit */
 
 static void smsc9420_stop_rx(struct smsc9420_pdata *pd)
 {
-       int timeOut = 1000;
+       int timeout = 1000;
        u32 mac_cr, dmac_control, dma_intr_ena;
 
        /* mask RX DMAC interrupts */
        smsc9420_pci_flush_write(pd);
 
        /* wait up to 10ms for receive to stop */
-       while (timeOut--) {
+       while (--timeout) {
                if (smsc9420_reg_read(pd, DMAC_STATUS) & DMAC_STS_RS_)
                        break;
                udelay(10);
        }
 
-       if (!timeOut)
+       if (!timeout)
                smsc_warn(IFDOWN, "RX DMAC did not stop! timeout.");
 
        /* ACK the Rx DMAC stop bit */
 
        cmd |= (MIF_FRAME_TAMSB);
        writel(cmd, gp->regs + MIF_FRAME);
 
-       while (limit--) {
+       while (--limit) {
                cmd = readl(gp->regs + MIF_FRAME);
                if (cmd & MIF_FRAME_TALSB)
                        break;
 
        spin_lock_irqsave(&phy_lock, flags);
 
        tsi108_write_mii(data, MII_BMCR, BMCR_RESET);
-       while (i--){
+       while (--i) {
                if(!(tsi108_read_mii(data, MII_BMCR) & BMCR_RESET))
                        break;
                udelay(10);