[NET]: Improve presentation of networking driver families.

Suggestion from Sam Ravnborg <sam@ravnborg.org>

It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
  token ring, wireless, PCMCIA, WAN, ATM, and S390.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 534b598866b37258af82d83f053c9fe8c494adfa..51ef8a0f750a641c93f529d1508addd7a3ce79c1 100644 (file)
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -23,9 +23,12 @@ config NETDEVICES
 
          If unsure, say Y.
 
+# All the following symbols are dependent on NETDEVICES - do not repeat
+# that for each of the symbols.
+if NETDEVICES
+
 config DUMMY
        tristate "Dummy net driver support"
-       depends on NETDEVICES
        ---help---
          This is essentially a bit-bucket device (i.e. traffic you send to
          this device is consigned into oblivion) with a configurable IP
@@ -45,7 +48,6 @@ config DUMMY
 
 config BONDING
        tristate "Bonding driver support"
-       depends on NETDEVICES
        depends on INET
        ---help---
          Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
@@ -63,7 +65,6 @@ config BONDING
 
 config EQUALIZER
        tristate "EQL (serial line load balancing) support"
-       depends on NETDEVICES
        ---help---
          If you have two serial connections to some other computer (this
          usually requires two modems and two telephone lines) and you use
@@ -83,7 +84,6 @@ config EQUALIZER
 
 config TUN
        tristate "Universal TUN/TAP device driver support"
-       depends on NETDEVICES
        select CRC32
        ---help---
          TUN/TAP provides packet reception and transmission for user space
@@ -107,7 +107,7 @@ config TUN
 
 config NET_SB1000
        tristate "General Instruments Surfboard 1000"
-       depends on NETDEVICES && PNP
+       depends on PNP
        ---help---
          This is a driver for the General Instrument (also known as
          NextLevel) SURFboard 1000 internal
@@ -129,16 +129,14 @@ config NET_SB1000
 
          If you don't have this card, of course say N.
 
-if NETDEVICES
        source "drivers/net/arcnet/Kconfig"
-endif
 
 #
 #      Ethernet
 #
 
 menu "Ethernet (10 or 100Mbit)"
-       depends on NETDEVICES && !UML
+       depends on !UML
 
 config NET_ETHERNET
        bool "Ethernet (10 or 100Mbit)"
@@ -1137,7 +1135,7 @@ config IBMLANA
 
 config IBMVETH
        tristate "IBM LAN Virtual Ethernet support"
-       depends on NETDEVICES && NET_ETHERNET && PPC_PSERIES
+       depends on NET_ETHERNET && PPC_PSERIES
        ---help---
          This driver supports virtual ethernet adapters on newer IBM iSeries
          and pSeries systems.
@@ -1760,7 +1758,7 @@ endmenu
 #
 
 menu "Ethernet (1000 Mbit)"
-       depends on NETDEVICES && !UML
+       depends on !UML
 
 config ACENIC
        tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
@@ -2091,7 +2089,7 @@ endmenu
 #
 
 menu "Ethernet (10000 Mbit)"
-       depends on NETDEVICES && !UML
+       depends on !UML
 
 config IXGB
        tristate "Intel(R) PRO/10GbE support"
@@ -2186,11 +2184,11 @@ source "drivers/s390/net/Kconfig"
 
 config ISERIES_VETH
        tristate "iSeries Virtual Ethernet driver support"
-       depends on NETDEVICES && PPC_ISERIES
+       depends on PPC_ISERIES
 
 config FDDI
        bool "FDDI driver support"
-       depends on NETDEVICES && (PCI || EISA)
+       depends on (PCI || EISA)
        help
          Fiber Distributed Data Interface is a high speed local area network
          design; essentially a replacement for high speed Ethernet. FDDI can
@@ -2239,7 +2237,7 @@ config SKFP
 
 config HIPPI
        bool "HIPPI driver support (EXPERIMENTAL)"
-       depends on NETDEVICES && EXPERIMENTAL && INET && PCI
+       depends on EXPERIMENTAL && INET && PCI
        help
          HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
          1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
@@ -2271,7 +2269,7 @@ config ROADRUNNER_LARGE_RINGS
 
 config PLIP
        tristate "PLIP (parallel port) support"
-       depends on NETDEVICES && PARPORT
+       depends on PARPORT
        ---help---
          PLIP (Parallel Line Internet Protocol) is used to create a
          reasonably fast mini network consisting of two (or, rarely, more)
@@ -2307,7 +2305,6 @@ config PLIP
 
 config PPP
        tristate "PPP (point-to-point protocol) support"
-       depends on NETDEVICES
        ---help---
          PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
          the same purpose: sending Internet traffic over telephone (and other
@@ -2443,7 +2440,6 @@ config PPPOATM
 
 config SLIP
        tristate "SLIP (serial line) support"
-       depends on NETDEVICES
        ---help---
          Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
          connect to your Internet service provider or to connect to some
@@ -2510,7 +2506,7 @@ config SLIP_MODE_SLIP6
 
 config NET_FC
        bool "Fibre Channel driver support"
-       depends on NETDEVICES && SCSI && PCI
+       depends on SCSI && PCI
        help
          Fibre Channel is a high speed serial protocol mainly used to connect
          large storage devices to the computer; it is compatible with and
@@ -2523,7 +2519,7 @@ config NET_FC
 
 config SHAPER
        tristate "Traffic Shaper (EXPERIMENTAL)"
-       depends on NETDEVICES && EXPERIMENTAL
+       depends on EXPERIMENTAL
        ---help---
          The traffic shaper is a virtual network device that allows you to
          limit the rate of outgoing data flow over some other network device.
@@ -2544,11 +2540,13 @@ config SHAPER
 
 config NETCONSOLE
        tristate "Network console logging support (EXPERIMENTAL)"
-       depends on NETDEVICES && INET && EXPERIMENTAL
+       depends on INET && EXPERIMENTAL
        ---help---
        If you want to log kernel messages over the network, enable this.
        See <file:Documentation/networking/netconsole.txt> for details.
 
+endif #NETDEVICES
+
 config NETPOLL
        def_bool NETCONSOLE