#include <asm/io.h>
+#define DRV_NAME "aec62xx"
+
struct chipset_bus_clock_list_entry {
u8 xfer_speed;
u8 chipset_settings;
};
static const struct ide_port_info aec62xx_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "AEC6210",
+ { /* 0: AEC6210 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_aec62xx,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
.port_ops = &atp850_port_ops,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
- },{ /* 1 */
- .name = "AEC6260",
+ },
+ { /* 1: AEC6260 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_aec62xx,
.port_ops = &atp86x_port_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_NO_AUTODMA |
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
- },{ /* 2 */
- .name = "AEC6260R",
+ },
+ { /* 2: AEC6260R */
+ .name = DRV_NAME,
.init_chipset = init_chipset_aec62xx,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
.port_ops = &atp86x_port_ops,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
- },{ /* 3 */
- .name = "AEC6280",
+ },
+ { /* 3: AEC6280 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_aec62xx,
.port_ops = &atp86x_port_ops,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
- },{ /* 4 */
- .name = "AEC6280R",
+ },
+ { /* 4: AEC6280R */
+ .name = DRV_NAME,
.init_chipset = init_chipset_aec62xx,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
.port_ops = &atp86x_port_ops,
unsigned long dma_base = pci_resource_start(dev, 4);
if (inb(dma_base + 2) & 0x10) {
- d.name = (idx == 4) ? "AEC6880R" : "AEC6880";
+ printk(KERN_INFO DRV_NAME " %s: AEC6880%s card detected"
+ "\n", pci_name(dev), (idx == 4) ? "R" : "");
d.udma_mask = ATA_UDMA6;
}
}
#include <asm/io.h>
+#define DRV_NAME "alim15x3"
+
/*
* Allow UDMA on M1543C-E chipset for WDC disks that ignore CRC checking
* (this is DANGEROUS and could result in data corruption).
};
static const struct ide_port_info ali15x3_chipset __devinitdata = {
- .name = "ALI15X3",
+ .name = DRV_NAME,
.init_chipset = init_chipset_ali15x3,
.init_hwif = init_hwif_ali15x3,
.init_dma = init_dma_ali15x3,
#include <linux/init.h>
#include <linux/ide.h>
+#define DRV_NAME "amd74xx"
+
enum {
AMD_IDE_CONFIG = 0x41,
AMD_CABLE_DETECT = 0x42,
IDE_HFLAG_IO_32BIT | \
IDE_HFLAG_UNMASK_IRQS)
-#define DECLARE_AMD_DEV(name_str, swdma, udma) \
+#define DECLARE_AMD_DEV(swdma, udma) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_chipset = init_chipset_amd74xx, \
.init_hwif = init_hwif_amd74xx, \
.enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \
.udma_mask = udma, \
}
-#define DECLARE_NV_DEV(name_str, udma) \
+#define DECLARE_NV_DEV(udma) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_chipset = init_chipset_amd74xx, \
.init_hwif = init_hwif_amd74xx, \
.enablebits = {{0x50,0x02,0x02}, {0x50,0x01,0x01}}, \
}
static const struct ide_port_info amd74xx_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_AMD_DEV("AMD7401", 0x00, ATA_UDMA2),
- /* 1 */ DECLARE_AMD_DEV("AMD7409", ATA_SWDMA2, ATA_UDMA4),
- /* 2 */ DECLARE_AMD_DEV("AMD7411", ATA_SWDMA2, ATA_UDMA5),
- /* 3 */ DECLARE_AMD_DEV("AMD7441", ATA_SWDMA2, ATA_UDMA5),
- /* 4 */ DECLARE_AMD_DEV("AMD8111", ATA_SWDMA2, ATA_UDMA6),
-
- /* 5 */ DECLARE_NV_DEV("NFORCE", ATA_UDMA5),
- /* 6 */ DECLARE_NV_DEV("NFORCE2", ATA_UDMA6),
- /* 7 */ DECLARE_NV_DEV("NFORCE2-U400R", ATA_UDMA6),
- /* 8 */ DECLARE_NV_DEV("NFORCE2-U400R-SATA", ATA_UDMA6),
- /* 9 */ DECLARE_NV_DEV("NFORCE3-150", ATA_UDMA6),
- /* 10 */ DECLARE_NV_DEV("NFORCE3-250", ATA_UDMA6),
- /* 11 */ DECLARE_NV_DEV("NFORCE3-250-SATA", ATA_UDMA6),
- /* 12 */ DECLARE_NV_DEV("NFORCE3-250-SATA2", ATA_UDMA6),
- /* 13 */ DECLARE_NV_DEV("NFORCE-CK804", ATA_UDMA6),
- /* 14 */ DECLARE_NV_DEV("NFORCE-MCP04", ATA_UDMA6),
- /* 15 */ DECLARE_NV_DEV("NFORCE-MCP51", ATA_UDMA6),
- /* 16 */ DECLARE_NV_DEV("NFORCE-MCP55", ATA_UDMA6),
- /* 17 */ DECLARE_NV_DEV("NFORCE-MCP61", ATA_UDMA6),
- /* 18 */ DECLARE_NV_DEV("NFORCE-MCP65", ATA_UDMA6),
- /* 19 */ DECLARE_NV_DEV("NFORCE-MCP67", ATA_UDMA6),
- /* 20 */ DECLARE_NV_DEV("NFORCE-MCP73", ATA_UDMA6),
- /* 21 */ DECLARE_NV_DEV("NFORCE-MCP77", ATA_UDMA6),
-
- /* 22 */ DECLARE_AMD_DEV("AMD5536", ATA_SWDMA2, ATA_UDMA5),
+ /* 0: AMD7401 */ DECLARE_AMD_DEV(0x00, ATA_UDMA2),
+ /* 1: AMD7409 */ DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA4),
+ /* 2: AMD7411/7441 */ DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA5),
+ /* 3: AMD8111 */ DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA6),
+
+ /* 4: NFORCE */ DECLARE_NV_DEV(ATA_UDMA5),
+ /* 5: >= NFORCE2 */ DECLARE_NV_DEV(ATA_UDMA6),
+
+ /* 6: AMD5536 */ DECLARE_AMD_DEV(ATA_SWDMA2, ATA_UDMA5),
};
static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id)
if (dev->revision <= 7)
d.swdma_mask = 0;
d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
- } else if (idx == 4) {
+ } else if (idx == 3) {
if (dev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
d.udma_mask = ATA_UDMA5;
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_COBRA_7401), 0 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7409), 1 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7411), 2 },
- { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_OPUS_7441), 3 },
- { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_8111_IDE), 4 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE), 5 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE), 6 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE), 7 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_OPUS_7441), 2 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_8111_IDE), 3 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE), 4 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE), 5 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA), 5 },
#endif
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE), 9 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE), 10 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE), 5 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA), 11 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2), 12 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2), 5 },
#endif
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE), 13 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE), 14 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE), 15 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE), 16 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 17 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE), 18 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE), 19 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE), 20 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE), 21 },
- { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 22 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE), 5 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 6 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, amd74xx_pci_tbl);
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "atiixp"
+
#define ATIIXP_IDE_PIO_TIMING 0x40
#define ATIIXP_IDE_MDMA_TIMING 0x44
#define ATIIXP_IDE_PIO_CONTROL 0x48
};
static const struct ide_port_info atiixp_pci_info[] __devinitdata = {
- { /* 0 */
- .name = "ATIIXP",
+ { /* 0: IXP200/300/400/700 */
+ .name = DRV_NAME,
.enablebits = {{0x48,0x01,0x00}, {0x48,0x08,0x00}},
.port_ops = &atiixp_port_ops,
.host_flags = IDE_HFLAG_LEGACY_IRQS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
- },{ /* 1 */
- .name = "SB600_PATA",
+ },
+ { /* 1: IXP600 */
+ .name = DRV_NAME,
.enablebits = {{0x48,0x01,0x00}, {0x00,0x00,0x00}},
.port_ops = &atiixp_port_ops,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_LEGACY_IRQS,
#include <asm/io.h>
+#define DRV_NAME "cmd64x"
+
#define CMD_DEBUG 0
#if CMD_DEBUG
};
static const struct ide_port_info cmd64x_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "CMD643",
+ { /* 0: CMD643 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
.port_ops = &cmd64x_port_ops,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = 0x00, /* no udma */
- },{ /* 1 */
- .name = "CMD646",
+ },
+ { /* 1: CMD646 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.chipset = ide_cmd646,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
- },{ /* 2 */
- .name = "CMD648",
+ },
+ { /* 2: CMD648 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.port_ops = &cmd64x_port_ops,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
- },{ /* 3 */
- .name = "CMD649",
+ },
+ { /* 3: CMD649 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.port_ops = &cmd64x_port_ops,
#include <linux/ide.h>
#include <linux/dma-mapping.h>
+#define DRV_NAME "cs5520"
+
struct pio_clocks
{
int address;
.set_dma_mode = cs5520_set_dma_mode,
};
-#define DECLARE_CS_DEV(name_str) \
- { \
- .name = name_str, \
- .port_ops = &cs5520_port_ops, \
- .host_flags = IDE_HFLAG_ISA_PORTS | \
- IDE_HFLAG_CS5520, \
- .pio_mask = ATA_PIO4, \
- }
-
-static const struct ide_port_info cyrix_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_CS_DEV("Cyrix 5510"),
- /* 1 */ DECLARE_CS_DEV("Cyrix 5520")
+static const struct ide_port_info cyrix_chipset __devinitdata = {
+ .name = DRV_NAME,
+ .port_ops = &cs5520_port_ops,
+ .host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_CS5520,
+ .pio_mask = ATA_PIO4,
};
/*
static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- const struct ide_port_info *d = &cyrix_chipsets[id->driver_data];
+ const struct ide_port_info *d = &cyrix_chipset;
hw_regs_t hw[4], *hws[] = { NULL, NULL, NULL, NULL };
ide_setup_pci_noise(dev, d);
}
pci_set_master(dev);
if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) {
- printk(KERN_WARNING "cs5520: No suitable DMA available.\n");
+ printk(KERN_WARNING "%s: No suitable DMA available.\n",
+ d->name);
return -ENODEV;
}
#include <asm/io.h>
+#define DRV_NAME "cs5530"
+
/*
* Here are the standard PIO mode 0-4 timings for each "format".
* Format-0 uses fast data reg timings, with slower command reg timings.
};
static const struct ide_port_info cs5530_chipset __devinitdata = {
- .name = "CS5530",
+ .name = DRV_NAME,
.init_chipset = init_chipset_cs5530,
.init_hwif = init_hwif_cs5530,
.port_ops = &cs5530_port_ops,
#include <linux/pci.h>
#include <linux/ide.h>
+#define DRV_NAME "cs5535"
+
#define MSR_ATAC_BASE 0x51300000
#define ATAC_GLD_MSR_CAP (MSR_ATAC_BASE+0)
#define ATAC_GLD_MSR_CONFIG (MSR_ATAC_BASE+0x01)
};
static const struct ide_port_info cs5535_chipset __devinitdata = {
- .name = "CS5535",
+ .name = DRV_NAME,
.port_ops = &cs5535_port_ops,
.host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_POST_SET_MODE,
.pio_mask = ATA_PIO4,
#include <asm/io.h>
+#define DRV_NAME "cy82c693"
+
/* the current version */
#define CY82_VERSION "CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)"
};
static const struct ide_port_info cy82c693_chipset __devinitdata = {
- .name = "CY82C693",
+ .name = DRV_NAME,
.init_chipset = init_chipset_cy82c693,
.init_iops = init_iops_cy82c693,
.port_ops = &cy82c693_port_ops,
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "ide_pci_generic"
+
static int ide_generic_all; /* Set to claim all devices */
module_param_named(all_generic_ide, ide_generic_all, bool, 0444);
#define IDE_HFLAGS_UMC (IDE_HFLAG_NO_DMA | IDE_HFLAG_FORCE_LEGACY_IRQS)
-#define DECLARE_GENERIC_PCI_DEV(name_str, extra_flags) \
+#define DECLARE_GENERIC_PCI_DEV(extra_flags) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA | \
extra_flags, \
.swdma_mask = ATA_SWDMA2, \
}
static const struct ide_port_info generic_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_GENERIC_PCI_DEV("Unknown", 0),
+ /* 0: Unknown */
+ DECLARE_GENERIC_PCI_DEV(0),
- { /* 1 */
- .name = "NS87410",
+ { /* 1: NS87410 */
+ .name = DRV_NAME,
.enablebits = { {0x43, 0x08, 0x08}, {0x47, 0x08, 0x08} },
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA,
.swdma_mask = ATA_SWDMA2,
.udma_mask = ATA_UDMA6,
},
- /* 2 */ DECLARE_GENERIC_PCI_DEV("SAMURAI", 0),
- /* 3 */ DECLARE_GENERIC_PCI_DEV("HT6565", 0),
- /* 4 */ DECLARE_GENERIC_PCI_DEV("UM8673F", IDE_HFLAGS_UMC),
- /* 5 */ DECLARE_GENERIC_PCI_DEV("UM8886A", IDE_HFLAGS_UMC),
- /* 6 */ DECLARE_GENERIC_PCI_DEV("UM8886BF", IDE_HFLAGS_UMC),
- /* 7 */ DECLARE_GENERIC_PCI_DEV("HINT_IDE", 0),
- /* 8 */ DECLARE_GENERIC_PCI_DEV("VIA_IDE", IDE_HFLAG_NO_AUTODMA),
- /* 9 */ DECLARE_GENERIC_PCI_DEV("OPTI621V", IDE_HFLAG_NO_AUTODMA),
-
- { /* 10 */
- .name = "VIA8237SATA",
+ /* 2: SAMURAI / HT6565 / HINT_IDE */
+ DECLARE_GENERIC_PCI_DEV(0),
+ /* 3: UM8673F / UM8886A / UM8886BF */
+ DECLARE_GENERIC_PCI_DEV(IDE_HFLAGS_UMC),
+ /* 4: VIA_IDE / OPTI621V / Piccolo010{2,3,5} */
+ DECLARE_GENERIC_PCI_DEV(IDE_HFLAG_NO_AUTODMA),
+
+ { /* 5: VIA8237SATA */
+ .name = DRV_NAME,
.host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA |
IDE_HFLAG_OFF_BOARD,
.swdma_mask = ATA_SWDMA2,
.udma_mask = ATA_UDMA6,
},
- /* 11 */ DECLARE_GENERIC_PCI_DEV("Piccolo0102", IDE_HFLAG_NO_AUTODMA),
- /* 12 */ DECLARE_GENERIC_PCI_DEV("Piccolo0103", IDE_HFLAG_NO_AUTODMA),
- /* 13 */ DECLARE_GENERIC_PCI_DEV("Piccolo0105", IDE_HFLAG_NO_AUTODMA),
-
- { /* 14 */
- .name = "Revolution",
+ { /* 6: Revolution */
+ .name = DRV_NAME,
.host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
IDE_HFLAG_TRUST_BIOS_FOR_DMA |
IDE_HFLAG_OFF_BOARD,
static const struct pci_device_id generic_pci_tbl[] = {
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87410), 1 },
{ PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE), 2 },
- { PCI_VDEVICE(HOLTEK, PCI_DEVICE_ID_HOLTEK_6565), 3 },
- { PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8673F), 4 },
- { PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8886A), 5 },
- { PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8886BF), 6 },
- { PCI_VDEVICE(HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE), 7 },
- { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C561), 8 },
- { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C558), 9 },
+ { PCI_VDEVICE(HOLTEK, PCI_DEVICE_ID_HOLTEK_6565), 2 },
+ { PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8673F), 3 },
+ { PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8886A), 3 },
+ { PCI_VDEVICE(UMC, PCI_DEVICE_ID_UMC_UM8886BF), 3 },
+ { PCI_VDEVICE(HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE), 2 },
+ { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C561), 4 },
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C558), 4 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_8237_SATA), 10 },
+ { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_8237_SATA), 5 },
#endif
- { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO), 11 },
- { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), 12 },
- { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), 13 },
- { PCI_VDEVICE(NETCELL, PCI_DEVICE_ID_REVOLUTION), 14 },
+ { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO), 4 },
+ { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), 4 },
+ { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), 4 },
+ { PCI_VDEVICE(NETCELL, PCI_DEVICE_ID_REVOLUTION), 6 },
/*
* Must come last. If you add entries adjust
* this table and generic_chipsets[] appropriately.
#include <linux/init.h>
#include <linux/ide.h>
+#define DRV_NAME "hpt34x"
+
#define HPT343_DEBUG_DRIVE_INFO 0
static void hpt34x_set_mode(ide_drive_t *drive, const u8 speed)
IDE_HFLAG_NO_AUTODMA)
static const struct ide_port_info hpt34x_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "HPT343",
+ { /* 0: HPT343 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_hpt34x,
.port_ops = &hpt34x_port_ops,
.host_flags = IDE_HFLAGS_HPT34X | IDE_HFLAG_NON_BOOTABLE,
.pio_mask = ATA_PIO5,
},
- { /* 1 */
- .name = "HPT345",
+ { /* 1: HPT345 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_hpt34x,
.port_ops = &hpt34x_port_ops,
.host_flags = IDE_HFLAGS_HPT34X | IDE_HFLAG_OFF_BOARD,
#include <asm/uaccess.h>
#include <asm/io.h>
+#define DRV_NAME "hpt366"
+
/* various tuning parameters */
#define HPT_RESET_STATE_ENGINE
#undef HPT_DELAY_INTERRUPT
if (dev2->irq != dev->irq) {
/* FIXME: we need a core pci_set_interrupt() */
dev2->irq = dev->irq;
- printk(KERN_INFO "HPT374 %s: PCI config space interrupt "
+ printk(KERN_INFO DRV_NAME " %s: PCI config space interrupt "
"fixed\n", pci_name(dev2));
}
}
pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
if (pin1 != pin2 && dev->irq == dev2->irq) {
- printk(KERN_INFO "HPT36x %s: onboard version of chipset, "
+ printk(KERN_INFO DRV_NAME " %s: onboard version of chipset, "
"pin1=%d pin2=%d\n", pci_name(dev), pin1, pin2);
return 1;
}
};
static const struct ide_port_info hpt366_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "HPT36x",
+ { /* 0: HPT36x */
+ .name = DRV_NAME,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.host_flags = IDE_HFLAGS_HPT3XX | IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
- },{ /* 1 */
- .name = "HPT372A",
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .port_ops = &hpt3xx_port_ops,
- .dma_ops = &hpt37x_dma_ops,
- .host_flags = IDE_HFLAGS_HPT3XX,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- },{ /* 2 */
- .name = "HPT302",
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .port_ops = &hpt3xx_port_ops,
- .dma_ops = &hpt37x_dma_ops,
- .host_flags = IDE_HFLAGS_HPT3XX,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- },{ /* 3 */
- .name = "HPT371",
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .port_ops = &hpt3xx_port_ops,
- .dma_ops = &hpt37x_dma_ops,
- .host_flags = IDE_HFLAGS_HPT3XX,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- },{ /* 4 */
- .name = "HPT374",
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = ATA_UDMA5,
- .port_ops = &hpt3xx_port_ops,
- .dma_ops = &hpt37x_dma_ops,
- .host_flags = IDE_HFLAGS_HPT3XX,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- },{ /* 5 */
- .name = "HPT372N",
+ },
+ { /* 1: HPT3xx */
+ .name = DRV_NAME,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
break;
}
- d = hpt366_chipsets[idx];
+ printk(KERN_INFO DRV_NAME ": %s chipset detected\n", info->chip_name);
+
+ d = hpt366_chipsets[min_t(u8, idx, 1)];
- d.name = info->chip_name;
d.udma_mask = info->udma_mask;
/* fixup ->dma_ops for HPT370/HPT370A */
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "it8213"
+
/**
* it8213_set_pio_mode - set host controller for PIO mode
* @drive: drive
};
static const struct ide_port_info it8213_chipset __devinitdata = {
- .name = "IT8213",
+ .name = DRV_NAME,
.enablebits = { {0x41, 0x80, 0x80} },
.port_ops = &it8213_port_ops,
.host_flags = IDE_HFLAG_SINGLE,
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "it821x"
+
struct it821x_dev
{
unsigned int smart:1, /* Are we in smart raid mode */
idev->timing10 = 1;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
if (idev->smart == 0)
- printk(KERN_WARNING "it821x %s: revision 0x10, "
+ printk(KERN_WARNING DRV_NAME " %s: revision 0x10, "
"workarounds activated\n", pci_name(dev));
}
/* Force the card into bypass mode if so requested */
if (it8212_noraid) {
- printk(KERN_INFO "it821x %s: forcing bypass mode\n",
+ printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n",
pci_name(dev));
it8212_disable_raid(dev);
}
pci_read_config_byte(dev, 0x50, &conf);
- printk(KERN_INFO "it821x %s: controller in %s mode\n",
+ printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n",
pci_name(dev), mode[conf & 1]);
return 0;
}
};
static const struct ide_port_info it821x_chipset __devinitdata = {
- .name = "IT821X",
+ .name = DRV_NAME,
.init_chipset = init_chipset_it821x,
.init_hwif = init_hwif_it821x,
.port_ops = &it821x_port_ops,
itdevs = kzalloc(2 * sizeof(*itdevs), GFP_KERNEL);
if (itdevs == NULL) {
- printk(KERN_ERR "it821x %s: out of memory\n", pci_name(dev));
+ printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev));
return -ENOMEM;
}
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "jmicron"
+
typedef enum {
PORT_PATA0 = 0,
PORT_PATA1 = 1,
};
static const struct ide_port_info jmicron_chipset __devinitdata = {
- .name = "JMB",
+ .name = DRV_NAME,
.enablebits = { { 0x40, 0x01, 0x01 }, { 0x40, 0x10, 0x10 } },
.port_ops = &jmicron_port_ops,
.pio_mask = ATA_PIO5,
#include <asm/io.h>
+#define DRV_NAME "ns87415"
+
#ifdef CONFIG_SUPERIO
/* SUPERIO 87560 is a PoS chip that NatSem denies exists.
* Unfortunately, it's built-in on all Astro-based PA-RISC workstations
};
static const struct ide_port_info ns87415_chipset __devinitdata = {
- .name = "NS87415",
+ .name = DRV_NAME,
.init_hwif = init_hwif_ns87415,
.port_ops = &ns87415_port_ops,
.dma_ops = &ns87415_dma_ops,
#include <asm/io.h>
+#define DRV_NAME "opti621"
+
#define READ_REG 0 /* index of Read cycle timing register */
#define WRITE_REG 1 /* index of Write cycle timing register */
#define CNTRL_REG 3 /* index of Control register */
};
static const struct ide_port_info opti621_chipset __devinitdata = {
- .name = "OPTI621/X",
+ .name = DRV_NAME,
.enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
.port_ops = &opti621_port_ops,
.host_flags = IDE_HFLAG_NO_DMA,
#include <asm/pci-bridge.h>
#endif
+#define DRV_NAME "pdc202xx_new"
+
#undef DEBUG
#ifdef DEBUG
if (dev2->irq != dev->irq) {
dev2->irq = dev->irq;
- printk(KERN_INFO "PDC20270 %s: PCI config space "
+ printk(KERN_INFO DRV_NAME " %s: PCI config space "
"interrupt fixed\n", pci_name(dev));
}
.cable_detect = pdcnew_cable_detect,
};
-#define DECLARE_PDCNEW_DEV(name_str, udma) \
+#define DECLARE_PDCNEW_DEV(udma) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_chipset = init_chipset_pdcnew, \
.port_ops = &pdcnew_port_ops, \
.host_flags = IDE_HFLAG_POST_SET_MODE | \
}
static const struct ide_port_info pdcnew_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_PDCNEW_DEV("PDC20268", ATA_UDMA5),
- /* 1 */ DECLARE_PDCNEW_DEV("PDC20269", ATA_UDMA6),
- /* 2 */ DECLARE_PDCNEW_DEV("PDC20270", ATA_UDMA5),
- /* 3 */ DECLARE_PDCNEW_DEV("PDC20271", ATA_UDMA6),
- /* 4 */ DECLARE_PDCNEW_DEV("PDC20275", ATA_UDMA6),
- /* 5 */ DECLARE_PDCNEW_DEV("PDC20276", ATA_UDMA6),
- /* 6 */ DECLARE_PDCNEW_DEV("PDC20277", ATA_UDMA6),
+ /* 0: PDC202{68,70} */ DECLARE_PDCNEW_DEV(ATA_UDMA5),
+ /* 1: PDC202{69,71,75,76,77} */ DECLARE_PDCNEW_DEV(ATA_UDMA6),
};
/**
static int __devinit pdc202new_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- const struct ide_port_info *d;
+ const struct ide_port_info *d = &pdcnew_chipsets[id->driver_data];
struct pci_dev *bridge = dev->bus->self;
- u8 idx = id->driver_data;
-
- d = &pdcnew_chipsets[idx];
- if (idx == 2 && bridge &&
+ if (dev->device == PCI_DEVICE_ID_PROMISE_20270 && bridge &&
bridge->vendor == PCI_VENDOR_ID_DEC &&
bridge->device == PCI_DEVICE_ID_DEC_21150) {
struct pci_dev *dev2;
}
}
- if (idx == 5 && bridge &&
+ if (dev->device == PCI_DEVICE_ID_PROMISE_20276 && bridge &&
bridge->vendor == PCI_VENDOR_ID_INTEL &&
(bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
- printk(KERN_INFO "PDC20276 %s: attached to I2O RAID controller,"
+ printk(KERN_INFO DRV_NAME " %s: attached to I2O RAID controller,"
" skipping\n", pci_name(dev));
return -ENODEV;
}
static const struct pci_device_id pdc202new_pci_tbl[] = {
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), 0 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), 1 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 2 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 3 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 4 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 5 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 6 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 0 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, pdc202new_pci_tbl);
#include <asm/io.h>
+#define DRV_NAME "pdc202xx_old"
+
#define PDC202XX_DEBUG_DRIVE_INFO 0
static const char *pdc_quirk_drives[] = {
.dma_timeout = pdc202xx_dma_timeout,
};
-#define DECLARE_PDC2026X_DEV(name_str, udma, extra_flags) \
+#define DECLARE_PDC2026X_DEV(udma, extra_flags) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_chipset = init_chipset_pdc202xx, \
.port_ops = &pdc2026x_port_ops, \
.dma_ops = &pdc2026x_dma_ops, \
}
static const struct ide_port_info pdc202xx_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "PDC20246",
+ { /* 0: PDC20246 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_pdc202xx,
.port_ops = &pdc20246_port_ops,
.dma_ops = &pdc20246_dma_ops,
.udma_mask = ATA_UDMA2,
},
- /* 1 */ DECLARE_PDC2026X_DEV("PDC20262", ATA_UDMA4, 0),
- /* 2 */ DECLARE_PDC2026X_DEV("PDC20263", ATA_UDMA4, 0),
- /* 3 */ DECLARE_PDC2026X_DEV("PDC20265", ATA_UDMA5, IDE_HFLAG_RQSIZE_256),
- /* 4 */ DECLARE_PDC2026X_DEV("PDC20267", ATA_UDMA5, IDE_HFLAG_RQSIZE_256),
+ /* 1: PDC2026{2,3} */
+ DECLARE_PDC2026X_DEV(ATA_UDMA4, 0),
+ /* 2: PDC2026{5,7} */
+ DECLARE_PDC2026X_DEV(ATA_UDMA5, IDE_HFLAG_RQSIZE_256),
};
/**
d = &pdc202xx_chipsets[idx];
- if (idx < 3)
+ if (idx < 2)
pdc202ata4_fixup_irq(dev, d->name);
- if (idx == 3) {
+ if (dev->vendor == PCI_DEVICE_ID_PROMISE_20265) {
struct pci_dev *bridge = dev->bus->self;
if (bridge &&
bridge->vendor == PCI_VENDOR_ID_INTEL &&
(bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
- printk(KERN_INFO "pdc202xx_old %s: skipping Promise "
+ printk(KERN_INFO DRV_NAME " %s: skipping Promise "
"PDC20265 attached to I2O RAID controller\n",
pci_name(dev));
return -ENODEV;
static const struct pci_device_id pdc202xx_pci_tbl[] = {
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 },
{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 2 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 3 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 4 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, pdc202xx_pci_tbl);
#include <asm/io.h>
+#define DRV_NAME "piix"
+
static int no_piix_dma;
/**
#define IDE_HFLAGS_PIIX 0
#endif
-#define DECLARE_PIIX_DEV(name_str, udma) \
+#define DECLARE_PIIX_DEV(udma) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_hwif = init_hwif_piix, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
.port_ops = &piix_port_ops, \
.udma_mask = udma, \
}
-#define DECLARE_ICH_DEV(name_str, udma) \
+#define DECLARE_ICH_DEV(udma) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_chipset = init_chipset_ich, \
.init_hwif = init_hwif_ich, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
}
static const struct ide_port_info piix_pci_info[] __devinitdata = {
- /* 0 */ DECLARE_PIIX_DEV("PIIXa", 0x00), /* no udma */
- /* 1 */ DECLARE_PIIX_DEV("PIIXb", 0x00), /* no udma */
-
- /* 2 */
+ /* 0: MPIIX */
{ /*
* MPIIX actually has only a single IDE channel mapped to
* the primary or secondary ports depending on the value
* of the bit 14 of the IDETIM register at offset 0x6c
*/
- .name = "MPIIX",
+ .name = DRV_NAME,
.enablebits = {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
.host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_NO_DMA |
IDE_HFLAGS_PIIX,
.pio_mask = ATA_PIO4,
/* This is a painful system best to let it self tune for now */
},
-
- /* 3 */ DECLARE_PIIX_DEV("PIIX3", 0x00), /* no udma */
- /* 4 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA2),
- /* 5 */ DECLARE_ICH_DEV("ICH0", ATA_UDMA2),
- /* 6 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA2),
- /* 7 */ DECLARE_ICH_DEV("ICH", ATA_UDMA4),
- /* 8 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA4),
- /* 9 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA2),
- /* 10 */ DECLARE_ICH_DEV("ICH2", ATA_UDMA5),
- /* 11 */ DECLARE_ICH_DEV("ICH2M", ATA_UDMA5),
- /* 12 */ DECLARE_ICH_DEV("ICH3M", ATA_UDMA5),
- /* 13 */ DECLARE_ICH_DEV("ICH3", ATA_UDMA5),
- /* 14 */ DECLARE_ICH_DEV("ICH4", ATA_UDMA5),
- /* 15 */ DECLARE_ICH_DEV("ICH5", ATA_UDMA5),
- /* 16 */ DECLARE_ICH_DEV("C-ICH", ATA_UDMA5),
- /* 17 */ DECLARE_ICH_DEV("ICH4", ATA_UDMA5),
- /* 18 */ DECLARE_ICH_DEV("ICH5-SATA", ATA_UDMA5),
- /* 19 */ DECLARE_ICH_DEV("ICH5", ATA_UDMA5),
- /* 20 */ DECLARE_ICH_DEV("ICH6", ATA_UDMA5),
- /* 21 */ DECLARE_ICH_DEV("ICH7", ATA_UDMA5),
- /* 22 */ DECLARE_ICH_DEV("ICH4", ATA_UDMA5),
- /* 23 */ DECLARE_ICH_DEV("ESB2", ATA_UDMA5),
- /* 24 */ DECLARE_ICH_DEV("ICH8M", ATA_UDMA5),
+ /* 1: PIIXa/PIIXb/PIIX3 */
+ DECLARE_PIIX_DEV(0x00), /* no udma */
+ /* 2: PIIX4 */
+ DECLARE_PIIX_DEV(ATA_UDMA2),
+ /* 3: ICH0 */
+ DECLARE_ICH_DEV(ATA_UDMA2),
+ /* 4: ICH */
+ DECLARE_ICH_DEV(ATA_UDMA4),
+ /* 5: PIIX4 */
+ DECLARE_PIIX_DEV(ATA_UDMA4),
+ /* 6: ICH[2-7]/ICH[2-3]M/C-ICH/ICH5-SATA/ESB2/ICH8M */
+ DECLARE_ICH_DEV(ATA_UDMA5),
};
/**
no_piix_dma = 2;
}
if(no_piix_dma)
- printk(KERN_WARNING "piix: 450NX errata present, disabling IDE DMA.\n");
+ printk(KERN_WARNING DRV_NAME ": 450NX errata present, disabling IDE DMA.\n");
if(no_piix_dma == 2)
- printk(KERN_WARNING "piix: A BIOS update may resolve this.\n");
+ printk(KERN_WARNING DRV_NAME ": A BIOS update may resolve this.\n");
}
static const struct pci_device_id piix_pci_tbl[] = {
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0), 0 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1), 1 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), 2 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1), 3 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB), 4 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1), 5 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1), 6 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1), 7 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1), 8 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX), 9 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9), 10 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8), 11 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 12 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 13 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 14 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 15 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11), 16 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 17 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0), 1 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1), 1 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), 0 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1), 1 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB), 2 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1), 3 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1), 2 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1), 4 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1), 5 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX), 2 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 6 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1), 18 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1), 6 },
#endif
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2), 19 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19), 20 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21), 21 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1), 22 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18), 23 },
- { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6), 24 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6), 6 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "rz1000"
+
static void __devinit init_hwif_rz1000 (ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
}
static const struct ide_port_info rz1000_chipset __devinitdata = {
- .name = "RZ100x",
+ .name = DRV_NAME,
.init_hwif = init_hwif_rz1000,
.chipset = ide_rz1000,
.host_flags = IDE_HFLAG_NO_DMA,
#include <asm/io.h>
+#define DRV_NAME "sc1200"
+
#define SC1200_REV_A 0x00
#define SC1200_REV_B1 0x01
#define SC1200_REV_B3 0x02
};
static const struct ide_port_info sc1200_chipset __devinitdata = {
- .name = "SC1200",
+ .name = DRV_NAME,
.port_ops = &sc1200_port_ops,
.dma_ops = &sc1200_dma_ops,
.host_flags = IDE_HFLAG_SERIALIZE |
#include <asm/io.h>
+#define DRV_NAME "serverworks"
+
#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
#define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "SvrWks OSB4",
+ { /* 0: OSB4 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_svwks,
.port_ops = &osb4_port_ops,
.host_flags = IDE_HFLAGS_SVWKS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = 0x00, /* UDMA is problematic on OSB4 */
- },{ /* 1 */
- .name = "SvrWks CSB5",
+ },
+ { /* 1: CSB5 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_svwks,
.port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
- },{ /* 2 */
- .name = "SvrWks CSB6",
+ },
+ { /* 2: CSB6 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_svwks,
.port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
- },{ /* 3 */
- .name = "SvrWks CSB6",
+ },
+ { /* 3: CSB6-2 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_svwks,
.port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
- },{ /* 4 */
- .name = "SvrWks HT1000",
+ },
+ { /* 4: HT1000 */
+ .name = DRV_NAME,
.init_chipset = init_chipset_svwks,
.port_ops = &svwks_port_ops,
.host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
#include <linux/init.h>
#include <linux/io.h>
+#define DRV_NAME "siimage"
+
/**
* pdev_is_sata - check if device is SATA
* @pdev: PCI device to check
.dma_lost_irq = ide_dma_lost_irq,
};
-#define DECLARE_SII_DEV(name_str, p_ops) \
+#define DECLARE_SII_DEV(p_ops) \
{ \
- .name = name_str, \
+ .name = DRV_NAME, \
.init_chipset = init_chipset_siimage, \
.init_iops = init_iops_siimage, \
.port_ops = p_ops, \
}
static const struct ide_port_info siimage_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_SII_DEV("SiI680", &sil_pata_port_ops),
- /* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA", &sil_sata_port_ops),
- /* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA", &sil_sata_port_ops)
+ /* 0: SiI680 */ DECLARE_SII_DEV(&sil_pata_port_ops),
+ /* 1: SiI3112 */ DECLARE_SII_DEV(&sil_sata_port_ops)
};
/**
static int first = 1;
if (first) {
- printk(KERN_INFO "siimage: For full SATA support you "
+ printk(KERN_INFO DRV_NAME ": For full SATA support you "
"should use the libata sata_sil module.\n");
first = 0;
}
* seem to get terminally confused in the PCI spaces.
*/
if (!request_mem_region(bar5, barsize, d.name)) {
- printk(KERN_WARNING "siimage %s: MMIO ports not "
+ printk(KERN_WARNING DRV_NAME " %s: MMIO ports not "
"available\n", pci_name(dev));
} else {
ioaddr = ioremap(bar5, barsize);
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), 0 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112), 1 },
- { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 2 },
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 1 },
#endif
{ 0, },
};
#include <linux/init.h>
#include <linux/ide.h>
+#define DRV_NAME "sis5513"
+
/* registers layout and init values are chipset family dependant */
#define ATA_16 0x01
}
pci_dev_put(host);
- printk(KERN_INFO "SIS5513 %s: %s %s controller\n",
+ printk(KERN_INFO DRV_NAME " %s: %s %s controller\n",
pci_name(dev), SiSHostChipInfo[i].name,
chipset_capability[chipset_family]);
}
pci_write_config_dword(dev, 0x54, idemisc);
if (trueid == 0x5518) {
- printk(KERN_INFO "SIS5513 %s: SiS 962/963 MuTIOL IDE UDMA133 controller\n",
+ printk(KERN_INFO DRV_NAME " %s: SiS 962/963 MuTIOL IDE UDMA133 controller\n",
pci_name(dev));
chipset_family = ATA_133;
*/
if ((idemisc & 0x40000000) == 0) {
pci_write_config_dword(dev, 0x54, idemisc | 0x40000000);
- printk(KERN_INFO "SIS5513 %s: Switching to 5513 register mapping\n",
+ printk(KERN_INFO DRV_NAME " %s: Switching to 5513 register mapping\n",
pci_name(dev));
}
}
pci_dev_put(lpc_bridge);
if (lpc_bridge->revision == 0x10 && (prefctl & 0x80)) {
- printk(KERN_INFO "SIS5513 %s: SiS 961B MuTIOL IDE UDMA133 controller\n",
+ printk(KERN_INFO DRV_NAME " %s: SiS 961B MuTIOL IDE UDMA133 controller\n",
pci_name(dev));
chipset_family = ATA_133a;
} else {
- printk(KERN_INFO "SIS5513 %s: SiS 961 MuTIOL IDE UDMA100 controller\n",
+ printk(KERN_INFO DRV_NAME " %s: SiS 961 MuTIOL IDE UDMA100 controller\n",
pci_name(dev));
chipset_family = ATA_100;
}
};
static const struct ide_port_info sis5513_chipset __devinitdata = {
- .name = "SIS5513",
+ .name = DRV_NAME,
.init_chipset = init_chipset_sis5513,
.enablebits = { {0x4a, 0x02, 0x02}, {0x4a, 0x04, 0x04} },
.host_flags = IDE_HFLAG_LEGACY_IRQS | IDE_HFLAG_NO_AUTODMA,
#include <asm/io.h>
+#define DRV_NAME "sl82c105"
+
#undef DEBUG
#ifdef DEBUG
};
static const struct ide_port_info sl82c105_chipset __devinitdata = {
- .name = "W82C105",
+ .name = DRV_NAME,
.init_chipset = init_chipset_sl82c105,
.enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
.port_ops = &sl82c105_port_ops,
* Never ever EVER under any circumstances enable
* DMA when the bridge is this old.
*/
- printk(KERN_INFO "W82C105_IDE: Winbond W83C553 bridge "
+ printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge "
"revision %d, BM-DMA disabled\n", rev);
d.dma_ops = NULL;
d.mwdma_mask = 0;
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "slc90e66"
+
static DEFINE_SPINLOCK(slc90e66_lock);
static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
};
static const struct ide_port_info slc90e66_chipset __devinitdata = {
- .name = "SLC90E66",
+ .name = DRV_NAME,
.enablebits = { {0x41, 0x80, 0x80}, {0x43, 0x80, 0x80} },
.port_ops = &slc90e66_port_ops,
.host_flags = IDE_HFLAG_LEGACY_IRQS,
#include <linux/pci.h>
#include <linux/ide.h>
-#define DRV_NAME "TC86C001"
+#define DRV_NAME "tc86c001"
static void tc86c001_set_mode(ide_drive_t *drive, const u8 speed)
{
};
static const struct ide_port_info tc86c001_chipset __devinitdata = {
- .name = "TC86C001",
+ .name = DRV_NAME,
.init_hwif = init_hwif_tc86c001,
.port_ops = &tc86c001_port_ops,
.dma_ops = &tc86c001_dma_ops,
#include <linux/ide.h>
#include <linux/init.h>
+#define DRV_NAME "triflex"
+
static void triflex_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
};
static const struct ide_port_info triflex_device __devinitdata = {
- .name = "TRIFLEX",
+ .name = DRV_NAME,
.enablebits = {{0x80, 0x01, 0x01}, {0x80, 0x02, 0x02}},
.port_ops = &triflex_port_ops,
.pio_mask = ATA_PIO4,
#include <asm/io.h>
+#define DRV_NAME "trm290"
+
static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
{
ide_hwif_t *hwif = HWIF(drive);
u8 reg = 0;
if ((dev->class & 5) && cfg_base)
- printk(KERN_INFO "TRM290 %s: chip", pci_name(dev));
+ printk(KERN_INFO DRV_NAME " %s: chip", pci_name(dev));
else {
cfg_base = 0x3df0;
- printk(KERN_INFO "TRM290 %s: using default", pci_name(dev));
+ printk(KERN_INFO DRV_NAME " %s: using default", pci_name(dev));
}
printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
hwif->config_data = cfg_base;
};
static const struct ide_port_info trm290_chipset __devinitdata = {
- .name = "TRM290",
+ .name = DRV_NAME,
.init_hwif = init_hwif_trm290,
.chipset = ide_trm290,
.port_ops = &trm290_port_ops,
#include <asm/processor.h>
#endif
+#define DRV_NAME "via82cxxx"
+
#define VIA_IDE_ENABLE 0x40
#define VIA_IDE_CONFIG 0x41
#define VIA_FIFO_CONFIG 0x43
};
static const struct ide_port_info via82cxxx_chipset __devinitdata = {
- .name = "VP_IDE",
+ .name = DRV_NAME,
.init_chipset = init_chipset_via82cxxx,
.enablebits = { { 0x40, 0x02, 0x02 }, { 0x40, 0x01, 0x01 } },
.port_ops = &via_port_ops,
*/
via_config = via_config_find(&isa);
if (!via_config->id) {
- printk(KERN_WARNING "VP_IDE %s: unknown chipset, skipping\n",
+ printk(KERN_WARNING DRV_NAME " %s: unknown chipset, skipping\n",
pci_name(dev));
return -ENODEV;
}
/*
* Print the boot message.
*/
- printk(KERN_INFO "VP_IDE %s: VIA %s (rev %02x) IDE %sDMA%s\n",
+ printk(KERN_INFO DRV_NAME " %s: VIA %s (rev %02x) IDE %sDMA%s\n",
pci_name(dev), via_config->name, isa->revision,
via_config->udma_mask ? "U" : "MW",
via_dma[via_config->udma_mask ?
}
if (via_clock < 20000 || via_clock > 50000) {
- printk(KERN_WARNING "VP_IDE: User given PCI clock speed "
+ printk(KERN_WARNING DRV_NAME ": User given PCI clock speed "
"impossible (%d), using 33 MHz instead.\n", via_clock);
- printk(KERN_WARNING "VP_IDE: Use ide0=ata66 if you want "
+ printk(KERN_WARNING DRV_NAME ": Use ide0=ata66 if you want "
"to assume 80-wire cable.\n");
via_clock = 33333;
}
vdev = kzalloc(sizeof(*vdev), GFP_KERNEL);
if (!vdev) {
- printk(KERN_ERR "VP_IDE %s: out of memory :(\n", pci_name(dev));
+ printk(KERN_ERR DRV_NAME " %s: out of memory :(\n",
+ pci_name(dev));
return -ENOMEM;
}
projects / linux-2.6-omap-h63xx.git / commitdiff