Jouni Hogander [Wed, 28 Jan 2009 02:44:38 +0000 (19:44 -0700)]
[ARM] OMAP3: PM: Emu_pwrdm is switched off by hardware even when sdti is in use
Using sdti doesn't keep emu_pwrdm on if hardware supervised pwrdm
transitions are used. This causes sdti stop to work when power
management is initialized and hardware supervised pwrdm control is
enabled. This patch disables hardware supervised pwrdm control for
emu_pwrdm. Now emu_pwrdm is switched off on boot by software when it
is not used.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:44:35 +0000 (19:44 -0700)]
[ARM] OMAP2/3 clockdomains: autodeps should respect platform flags
Fix the clockdomain autodep code to respect omap_chip platform flags.
Resolves "Unable to handle kernel paging request at virtual address 5f75706d" panic during power management initialization on OMAP2.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tomi Valkeinen [Wed, 28 Jan 2009 02:44:31 +0000 (19:44 -0700)]
[ARM] OMAP: wait for pwrdm transition after clk_enable()
Enabling clock in a disabled power domain causes the power domain to be
turned on. However, the power transition is not always finished when
clk_enable() returns and this randomly crashes the kernel when an
interrupt happens right after the clk_enable, and the kernel tries to
read the irq status register for that domain.
Why the irq status register is inaccessible, I don't know. Also it
doesn't seem to be related to the module being not powered up, but to
the transition itself.
The same could perhaps happen after clk_disable also, but I have not
witnessed that.
The problem affects at least dss, cam and sgx clocks.
This change waits for the transition to be finished before returning
from omap2_clkdm_clk_enable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:44:28 +0000 (19:44 -0700)]
[ARM] OMAP3 powerdomains: remove RET from SGX power states list
The SGX device on OMAP3 does not support retention, so remove RET from the
list of possible SGX power states. Problem debugged by Richard Woodruff
<r-woodruff2@ti.com>.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:44:18 +0000 (19:44 -0700)]
[ARM] OMAP3 PRCM: add DPLL1-5 powerdomains, clockdomains; mark clocks
Each DPLL exists in its own powerdomain (cf 34xx TRM figure 4-18) and
clockdomain; so, create powerdomain and clockdomain structures for them.
Mark each DPLL clock as belonging to their respective DPLL clockdomain.
cf. 34xx TRM Table 4-27 (among other references).
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Thu, 8 May 2008 01:19:07 +0000 (19:19 -0600)]
[ARM] OMAP3 clock: move sys_clkout2 clk to core_clkdm
sys_clkout2 belongs in the core_clkdm (3430 TRM section 4.7.2.2).
It's not clear whether it actually is in the CORE clockdomain, or whether
it is technically in a different clockdomain; but this is closer to
reality than the present configuration.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 10 Sep 2008 16:47:36 +0000 (10:47 -0600)]
[ARM] OMAP2/3 clockdomains: add CM and PRM clkdms
Add clockdomains for the CM and PRM. These will ultimately replace the
"wkup_clkdm", which appears to not actually exist on the hardware.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Tue, 3 Feb 2009 09:10:03 +0000 (02:10 -0700)]
[ARM] OMAP2/3 clockdomains: combine pwrdm, pwrdm_name into union in struct clockdomain
struct clockdomain contains a struct powerdomain *pwrdm and const char
*pwrdm_name. The pwrdm_name is only used at initialization to look up
the appropriate pwrdm pointer. Combining these into a union saves
about 100 bytes on 3430SDP. This patch should not cause any change in
kernel function.
Updated to gracefully handle autodeps that contain invalid powerdomains,
per Russell King's review comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kevin Hilman [Wed, 28 Jan 2009 02:13:38 +0000 (19:13 -0700)]
[ARM] OMAP2: Implement CPUfreq frequency table based on PRCM table
This patch adds a CPUfreq frequency-table implementation for OMAP2 by
walking the PRCM rate-table for available entries and adding them to a
CPUfreq table.
CPUfreq can then be used to manage switching between all the available
entries in the PRCM rate table. Either use the CPUfreq sysfs
interface directly, (see Section 3 of Documentation/cpu-freq/user-guide.txt)
or use the cpufrequtils package:
http://www.kernel.org/pub/linux/utils/kernel/cpufreq/cpufrequtils.html
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Updated to try to use cpufreq_table if it exists.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:13:12 +0000 (19:13 -0700)]
[ARM] OMAP: Make dpll4_m4_ck programmable with clk_set_rate()
Filling the set_rate and round_rate fields of dpll4_m4_ck makes
this clock programmable through clk_set_rate(). This is needed
to give omapfb control over the dss1_alwon_fck rate.
This patch includes a fix from Tomi Valkeinen <tomi.valkeinen@nokia.com>.
Signed-off-by: Måns Rullgård <mans@mansr.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Stone <daniel.stone@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:13:02 +0000 (19:13 -0700)]
[ARM] OMAP3 clock: fix 96MHz clocks
Fix some bugs in the OMAP3 clock tree pertaining to the 96MHz clocks.
The 96MHz portion of the clock tree should now have reasonable
fidelity to the 34xx TRM Rev I.
One remaining question mark: it's not clear exactly which 96MHz source
clock the USIM uses. This patch sticks with the previous setting, which
seems reasonable.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:12:57 +0000 (19:12 -0700)]
[ARM] OMAP3: move USBHOST SAR handling from clock framework to powerdomain layer
Remove usbhost_sar_fclk from the OMAP3 clock framework. The bit that
the clock was tweaking doesn't actually enable or disable a clock; it
controls whether the hardware will save and restore USBHOST state
when the powerdomain changes state. (That happens to coincidentally
enable a clock for the duration of the operation, hence the earlier
confusion.)
In place of the clock, mark the USBHOST powerdomain as supporting
hardware save-and-restore functionality.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:12:50 +0000 (19:12 -0700)]
[ARM] OMAP: Fix sparse, checkpatch warnings in OMAP2/3 PRCM/PM code
Fix sparse & checkpatch warnings in OMAP2/3 PRCM & PM code. This mostly
consists of:
- converting pointer comparisons to integers in form similar to
(ptr == 0) to the standard idiom (!ptr)
- labeling a few non-static private functions as static
- adding prototypes for *_init() functions in the appropriate header
files, and getting rid of the corresponding open-coded extern
prototypes in other C files
- renaming the variable 'sclk' in mach-omap2/clock.c:omap2_get_apll_clkin
to avoid shadowing an earlier declaration
Clean up checkpatch issues. This mostly involves:
- converting some asm/ includes to linux/ includes
- cleaning up some whitespace
- getting rid of braces for conditionals with single following statements
Also take care of a few odds and ends, including:
- getting rid of unlikely() and likely() - none of this code is particularly
fast-path code, so the performance impact seems slim; and some of those
likely() and unlikely() indicators are probably not as accurate as the
ARM's branch predictor
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:12:47 +0000 (19:12 -0700)]
[ARM] OMAP2/3: Add non-CORE DPLL rate set code and M, N programming
Add non-CORE DPLL rate set code and M,N programming for OMAP3.
Connect it to OMAP34xx DPLLs 1, 2, 4, 5 via the clock framework.
You may see some warnings on rate sets from the freqsel code. The
table that TI presented in the 3430 TRM Rev F does not cover Fint <
750000, which definitely occurs in practice. However, the lack of this
freqsel case does not appear to impair the DPLL rate change.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 22 Jan 2009 19:41:20 +0000 (19:41 +0000)]
[ARM] omap: spi: arrange for omap_uwire to use connection ID
... which now means no driver requests the "armxor_ck" clock directly.
Also, fix the error handling for clk_get(), ensuring that we propagate
the error returned from clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 23 Jan 2009 22:57:12 +0000 (22:57 +0000)]
[ARM] omap: i2c: remove conditional ick clocks
By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c. Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 23 Jan 2009 10:26:46 +0000 (10:26 +0000)]
[ARM] omap: mcbsp: convert to use fck/ick clocks directly
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 19 Jan 2009 20:53:30 +0000 (20:53 +0000)]
[ARM] omap: MMC: convert clocks to match by devid and conid
Convert OMAP MMC driver to match clocks using the device ID and a
connection ID rather than a clock name. This allows us to eliminate
the OMAP1/OMAP2 differences for the function clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 23 Jan 2009 22:34:09 +0000 (22:34 +0000)]
[ARM] omap: provide a dummy clock node
By providing a dummy clock node, we can eliminate the SoC conditional
clock handing in the OMAP drivers, moving this knowledge out of the
driver and into the machine clock support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 22 Jan 2009 16:08:04 +0000 (16:08 +0000)]
[ARM] omap: allow double-registering of clocks
This stops things blowing up if a 'struct clk' to be passed more
than once to clk_register(), which will be required when we decouple
struct clk's from their names.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Feb 2009 16:07:46 +0000 (16:07 +0000)]
[ARM] omap: handle RATE_CKCTL via .set_rate/.round_rate methods
It makes no sense to have the CKCTL rate selection implemented as a flag
and a special exception in the top level set_rate/round_rate methods.
Provide CKCTL set_rate/round_rate methods, and use these for where ever
RATE_CKCTL is used and they're not already overridden. This allows us
to remove the RATE_CKCTL flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 13 Nov 2008 13:44:15 +0000 (13:44 +0000)]
[ARM] omap: move propagate_rate() calls into generic omap clock code
propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion. So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 13 Nov 2008 13:07:00 +0000 (13:07 +0000)]
[ARM] omap: remove unnecessary calls to propagate_rate()
We've always called propagate_rate() in the parent function to
the .set_rate methods, so there's no point having the .set_rate
methods also call this heavy-weight function - it's mere
duplication of what's happening elsewhere.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 13 Nov 2008 13:01:32 +0000 (13:01 +0000)]
[ARM] omap: move clock propagation into core omap clock code
Move the clock propagation calls for set_parent and set_rate into
the core omap clock code, rather than having these calls scattered
throughout the OMAP1 and OMAP2 implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ingo Molnar [Thu, 5 Feb 2009 15:03:34 +0000 (16:03 +0100)]
drm/i915: select framebuffer support automatically
Migration helper.
The i915 driver recently added a 'depends on FB' rule to its
Kconfig entry - which silently turns off DRM_I915 if someone
has a working config but no CONFIG_FB selected, and upgrades
to the latest upstream kernel.
So change it to "select FB", which auto-selects framebuffer
support. This way the driver keeps working, regardless of
whether FB was enabled before or not.
Kconfig select's of interactive options can be problematic to
dependencies and can cause build breakages - but in this case
it's safe because it's a leaf entry with no dependencies of its
own.
( There is some minor circular dependency fallout as FB_I810
and FB_INTEL also used 'depends on FB' constructs - update
those to "select FB" too. )
Jesse Barnes [Fri, 6 Feb 2009 18:22:41 +0000 (10:22 -0800)]
drm/i915: add get_vblank_counter function for GM45
As discussed in the long thread about vblank related timeouts, it turns out
GM45 has different frame count registers than previous chips. This patch
adds support for them, which prevents us from waiting on really stale
sequence values in drm_wait_vblank (which rather than returning immediately
ends up timing out or getting interrupted).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@linux.ie>
Jesse Barnes [Fri, 6 Feb 2009 21:04:49 +0000 (13:04 -0800)]
drm/i915: capture last_vblank count at IRQ uninstall time too
In dc1336ff4fe08ae7cfe8301bfd7f0b2cfd31d20a (set vblank enable flag correctly
across IRQ uninstall), we made sure drivers that uninstall their interrupt
handler set the vblank enabled flag correctly, so that when interrupts are
re-enabled, vblank interrupts & counts work as expected. However I missed the
last_vblank field: it needs to be updated as well, otherwise, at the next
drm_update_vblank_count we'll end up comparing a current count to a stale
one (the last one captured by the disable function), which may trigger the
wraparound handling, leading to a jumpy counter and hangs in drm_wait_vblank.
The jumpy counter can prevent the DRM_WAIT_ON from returning success if the
difference between the current count and the requested count is greater than
2^23, leading to timeouts or hangs, if the ioctl is restarted in a loop (as
is the case in libdrm < 2.4.4).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by: Michel Dänzer <michel@daenzer.net> Tested-by: Timo Aaltonen <tjaalton@cc.hut.fi> Signed-off-by: Dave Airlie <airlied@redhat.com>
Russell King [Tue, 4 Nov 2008 21:24:00 +0000 (21:24 +0000)]
[ARM] omap: don't use clkops_omap2_dflt_wait for non-ICLK/FCLK clocks
The original code in omap2_clk_wait_ready() used to check the low 8
bits to determine whether they were within the FCLKEN or ICLKEN
registers. Specifically, the test is satisfied when these offsets
are used:
If one of these offsets isn't used, omap2_clk_wait_ready() merely
returns without doing anything. So we should use the non-wait clkops
version instead and eliminate that conditional.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 4 Nov 2008 18:59:32 +0000 (18:59 +0000)]
[ARM] omap: eliminate unnecessary conditionals in omap2_clk_wait_ready
Rather than employing run-time tests in omap2_clk_wait_ready() to
decide whether we need to wait for the clock to become ready, we
can set the .ops appropriately.
This change deals with the OMAP24xx and OMAP34xx conditionals only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 4 Nov 2008 16:48:35 +0000 (16:48 +0000)]
[ARM] omap: kill PARENT_CONTROLS_CLOCK
PARENT_CONTROLS_CLOCK just makes enable/disable no-op, and is
functionally an alias for ALWAYS_ENABLED. This can be handled
in the same way, using clkops_null.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Anholt [Tue, 3 Feb 2009 20:10:21 +0000 (12:10 -0800)]
drm/i915: Quiet the message on get/setparam ioctl with an unknown value.
Getting an unknown get/setparam used to be more significant back when they
didn't change much. However, now that we're in the git world we're using
them instead of a monotonic version number to signal feature availability,
so clients ask about unknown params on older kernels more often.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
Paul Collins [Wed, 4 Feb 2009 10:05:41 +0000 (23:05 +1300)]
drm/i915: skip LVDS initialization on Apple Mac Mini
The Apple Mac Mini falsely reports LVDS. Use DMI to check whether we
are running on a Mac Mini, and skip LVDS initialization if that proves
to be the case.
Signed-off-by: Paul Collins <paul@ondioline.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
Jesse Barnes [Tue, 27 Jan 2009 01:10:45 +0000 (17:10 -0800)]
drm/i915: add fence register management to execbuf
Adds code to set up fence registers at execbuf time on pre-965 chips as
necessary. Also fixes up a few bugs in the pre-965 tile register support
(get_order != ffs). The number of fences available to the kernel defaults
to the hw limit minus 3 (for legacy X front/back/depth), but a new parameter
allows userspace to override that as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
Eric Anholt [Tue, 27 Jan 2009 18:33:49 +0000 (10:33 -0800)]
drm/i915: Return error from i915_gem_object_get_fence_reg() when failing.
Previously, the caller would continue along without knowing that the
function failed, resulting in potential mis-rendering. Right now vm_fault
just returns SIGBUS in that case, and we may need to disable signal handling
to avoid that happening.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
Eric Anholt [Fri, 23 Jan 2009 20:57:47 +0000 (12:57 -0800)]
drm/i915: Set up an MTRR covering the GTT at driver load.
We'd love to just be using PAT, but even on chips with PAT it gets disabled
sometimes due to an errata. It would probably be better to have pat_enabled
exported and only bother with this when !pat_enabled.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
Steven Rostedt [Fri, 6 Feb 2009 06:14:26 +0000 (01:14 -0500)]
ftrace: change function graph tracer to use new in_nmi
The function graph tracer piggy backed onto the dynamic ftracer
to use the in_nmi custom code for dynamic tracing. The problem
was (as Andrew Morton pointed out) it really only wanted to bail
out if the context of the current CPU was in NMI context. But the
dynamic ftrace in_nmi custom code was true if _any_ CPU happened
to be in NMI context.
Now that we have a generic in_nmi interface, this patch changes
the function graph code to use it instead of the dynamic ftarce
custom code.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Steven Rostedt [Fri, 6 Feb 2009 05:51:37 +0000 (00:51 -0500)]
nmi: add generic nmi tracking state
This code adds an in_nmi() macro that uses the current tasks preempt count
to track when it is in NMI context. Other parts of the kernel can
use this to determine if the context is in NMI context or not.
This code was inspired by the -rt patch in_nmi version that was
written by Peter Zijlstra, who borrowed that code from
Mathieu Desnoyers.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Steven Rostedt [Fri, 6 Feb 2009 03:30:07 +0000 (22:30 -0500)]
ftrace, x86: rename in_nmi variable
Impact: clean up
The in_nmi variable in x86 arch ftrace.c is a misnomer.
Andrew Morton pointed out that the in_nmi variable is incremented
by all CPUS. It can be set when another CPU is running an NMI.
Since this is actually intentional, the fix is to rename it to
what it really is: "nmi_running"
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Steven Rostedt [Fri, 6 Feb 2009 00:54:51 +0000 (19:54 -0500)]
ring-buffer: allow tracing_off to be used in core kernel code
tracing_off() is the fastest way to stop recording to the ring buffers.
This may be used in places like panic and die, just before the
ftrace_dump is called.
This patch adds the appropriate CPP conditionals to make it a stub
function when the ring buffer is not configured it.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Steven Rostedt [Thu, 5 Feb 2009 23:43:07 +0000 (18:43 -0500)]
ring-buffer: add NMI protection for spinlocks
Impact: prevent deadlock in NMI
The ring buffers are not yet totally lockless with writing to
the buffer. When a writer crosses a page, it grabs a per cpu spinlock
to protect against a reader. The spinlocks taken by a writer are not
to protect against other writers, since a writer can only write to
its own per cpu buffer. The spinlocks protect against readers that
can touch any cpu buffer. The writers are made to be reentrant
with the spinlocks disabling interrupts.
The problem arises when an NMI writes to the buffer, and that write
crosses a page boundary. If it grabs a spinlock, it can be racing
with another writer (since disabling interrupts does not protect
against NMIs) or with a reader on the same CPU. Luckily, most of the
users are not reentrant and protects against this issue. But if a
user of the ring buffer becomes reentrant (which is what the ring
buffers do allow), if the NMI also writes to the ring buffer then
we risk the chance of a deadlock.
This patch moves the ftrace_nmi_enter called by nmi_enter() to the
ring buffer code. It replaces the current ftrace_nmi_enter that is
used by arch specific code to arch_ftrace_nmi_enter and updates
the Kconfig to handle it.
When an NMI is called, it will set a per cpu variable in the ring buffer
code and will clear it when the NMI exits. If a write to the ring buffer
crosses page boundaries inside an NMI, a trylock is used on the spin
lock instead. If the spinlock fails to be acquired, then the entry
is discarded.
This bug appeared in the ftrace work in the RT tree, where event tracing
is reentrant. This workaround solved the deadlocks that appeared there.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Steven Rostedt [Sun, 8 Feb 2009 00:38:43 +0000 (19:38 -0500)]
trace: remove deprecated entry->cpu
Impact: fix to prevent developers from using entry->cpu
With the new ring buffer infrastructure, the cpu for the entry is
implicit with which CPU buffer it is on.
The original code use to record the current cpu into the generic
entry header, which can be retrieved by entry->cpu. When the
ring buffer was introduced, the users were convert to use the
the cpu number of which cpu ring buffer was in use (this was passed
to the tracers by the iterator: iter->cpu).
Unfortunately, the cpu item in the entry structure was never removed.
This allowed for developers to use it instead of the proper iter->cpu,
unknowingly, using an uninitialized variable. This was not the fault
of the developers, since it would seem like the logical place to
retrieve the cpu identifier.
This patch removes the cpu item from the entry structure and fixes
all the users that should have been using iter->cpu.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Linus Torvalds [Sat, 7 Feb 2009 18:46:30 +0000 (10:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: make the PM core more careful with drivers using the new PM framework
PCI PM: Read power state from device after trying to change it on resume
PCI PM: Do not disable and enable bridges during suspend-resume
PCI: PCIe portdrv: Simplify suspend and resume
PCI PM: Fix saving of device state in pci_legacy_suspend
PCI PM: Check if the state has been saved before trying to restore it
PCI PM: Fix handling of devices without drivers
PCI: return error on failure to read PCI ROMs
PCI: properly clean up ASPM link state on device remove
Rusty Russell [Sat, 7 Feb 2009 07:45:56 +0000 (18:15 +1030)]
module: remove over-zealous check in __module_get()
Impact: fix spurious BUG_ON() triggered under load
module_refcount() isn't reliable outside stop_machine(), as demonstrated
by Karsten Keil <kkeil@suse.de>, networking can trigger it under load
(an inc on one cpu and dec on another while module_refcount() is tallying
can give false results, for example).
Almost noone should be using __module_get, but that's another issue.
Linus Torvalds [Sat, 7 Feb 2009 16:30:20 +0000 (08:30 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (30 commits)
ACPI: Kconfig text - Fix the ACPI_CONTAINER module name according to the real module name.
eeepc-laptop: fix oops when changing backlight brightness during eeepc-laptop init
ACPICA: Fix table entry truncation calculation
ACPI: Enable bit 11 in _PDC to advertise hw coord
ACPI: struct device - replace bus_id with dev_name(), dev_set_name()
ACPI: add missing KERN_* constants to printks
ACPI: dock: Don't eval _STA on every show_docked sysfs read
ACPI: disable ACPI cleanly when bad RSDP found
ACPI: delete CPU_IDLE=n code
ACPI: cpufreq: Remove deprecated /proc/acpi/processor/../performance proc entries
ACPI: make some IO ports off-limits to AML
ACPICA: add debug dump of BIOS _OSI strings
ACPI: proc_dir_entry 'video/VGA' already registered
ACPI: Skip the first two elements in the _BCL package
ACPI: remove BM_RLD access from idle entry path
ACPI: remove locking from PM1x_STS register reads
eeepc-laptop: use netlink interface
eeepc-laptop: Implement rfkill hotplugging in eeepc-laptop
eeepc-laptop: Check return values from rfkill_register
eeepc-laptop: Add support for extended hotkeys
...
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:23:12 +0000 (23:23 +0000)]
igb: update version number and copyright dates
Update the version number to 1.3.16 and update copyright dates for 2009.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:22:52 +0000 (23:22 +0000)]
igb: fix two minor items found during code review
This patch addresses two minor items I found while cleaning up the igb
driver for our sourceforge version.
The first clears the context index if we don't flag that we need it.
The second item is that eims_other should be used instead of bit defines
when setting all of the EICS bits prior to reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:22:32 +0000 (23:22 +0000)]
igb: update stats before doing reset in igb_down
It was seen with repeated interface up/down testing that there was a large
stray between the stats reported by the queues and the stats reported by the
HW. It was found to be an issue in that hw stats were being reset without
first being recorded. This change records the stats before wiping them from
the system via the reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:22:11 +0000 (23:22 +0000)]
igb: remove redundant count set and err_hw_init
Remove the setting of ring->count variables from igb_probe as they are
duplicating the same configuration that is done igb_alloc_queues.
Remove the err_hw_init tag as it can be replaced by err_sw_init.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:21:51 +0000 (23:21 +0000)]
igb: remove disable_av variable from mac_info struct
The disable_av variable is never used by the driver and provides no value as
it is likely a leftover debugging variable. I have removed it and replaced
the one spot that checked for it with a check for a valid address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:21:31 +0000 (23:21 +0000)]
igb: change pba size determination from if to switch statement
As additional hardware is added to the igb driver it is easier to support
the expansion via switch statements instead of using nested ifs. For
this reason I am changing this to a switch statement.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:21:10 +0000 (23:21 +0000)]
igb: move get_hw_control within igb_resume.
Move igb_get_hw_control up so that it is called just after the reset in
igb_resume. This notifies the HW sooner that the driver is reassuming
control of the device.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:20:49 +0000 (23:20 +0000)]
igb: don't read eicr when responding to legacy interrupts
The interrupt handler was reading eicr and then doing nothing with the
result. I have removed the variable and the register read since they
provide no value to the legacy interrupt handler.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:20:31 +0000 (23:20 +0000)]
igb: remove unnecessary adapter->hw calls when just hw-> will do.
There were several spots in the code making calls to adapter->hw when they
could have just been accessing hw-> directly. I cleaned up the spots where
this was visibly apparent.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:20:10 +0000 (23:20 +0000)]
igb: rename igb_update_mc_addr_list_82575 to not include the 82575
There isn't much point in having the _82575 hanging off the end of this
function since there aren't any other version of this function running
around within this driver. This also allows for a bit of whitespace
cleanup due to a shorter function name.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:19:50 +0000 (23:19 +0000)]
igb: remove redundant timer updates and cleanup watchdog_task
The igb watchdog task is modifying the watchdog timer twice duing a single
run. It only needs to be called once to reschedule itself for 2 seconds from
the last time it ran.
In addition I removed the allocation of the mac_info structure since it is
only called twice and is easier to access via the e1000_hw struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:19:29 +0000 (23:19 +0000)]
igb: cleanup igb_netpoll to be more friendly with napi & GRO
This patch cleans up igb_netpoll so that it is more friendly with both the
current napi and newly introduced GRO features.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:19:08 +0000 (23:19 +0000)]
igb: add counter for dma out of sync errors
Add a counter for dma out of sync errors reported via interrupt.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:18:48 +0000 (23:18 +0000)]
igb: update testing done by ethtool
Most of the code for the testing has pretty much become stale at this point
and is need of update. This update just streamlines most of the code,
widens the range of interrupt testing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:18:27 +0000 (23:18 +0000)]
igb: update feature flags supported in ethtool
This driver is currently using HW_CSUM which is not correct. Update this
to use the IP_CSUM and IPV6_CSUM flags. In addition consolidate the TSO
flag setting.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:18:06 +0000 (23:18 +0000)]
igb: remove unused rx_hdr_split statistic
This statistic is not used and so it is safe to remove
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:17:47 +0000 (23:17 +0000)]
igb: rename nvm ops
All of the nvm ops have the tag _nvm added to the end which is redundant
since all of the calls to the ops have to go through the nvm ops struct
anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:17:26 +0000 (23:17 +0000)]
igb: rename phy ops
This patch renames write_phy_reg to write_reg and read_phy_reg to read_reg.
It seems redundant to call out phy in an operation that is part of the
phy_ops struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 6 Feb 2009 23:17:06 +0000 (23:17 +0000)]
igb: read address from RAH/RAL instead of from EEPROM
Instead of pulling the mac address from EEPROM it is easier to pull it from
the RAL/RAH registers and then just copy it into the address structures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log