Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
The definitions of S3C2412_IISMOD_SDF_MSB and S3C2412_IISMOD_SDF_LSB
are incorrect, being the same S3C2412_IISMOD_SDF_IIS which is the
only correct one in this series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
David Brownell [Sun, 8 Mar 2009 19:44:39 +0000 (19:44 +0000)]
omap3 boards list voltage ranges for VMMC1, VMMC2,
It seems the regulator framework is going to require boards
to explicitly configure voltage ranges, instead of letting
them just pick up the entire available range. So this patch
updates OMAP3 board handling for VMMC1, VMMC2, and VSIM.
Also, change the label for the MMC1 DAT4..DAT7 supply to
"vmmc_aux", so the label isn't specific to MMC1. Things
like SDIO and eMMC chips may also need a second voltage,
though in that case it's usually 1.8V for chip interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Xiaotian Feng [Fri, 6 Mar 2009 03:01:23 +0000 (11:01 +0800)]
cpm_uart: fix non-console port startup bug
After UART interrupt handler is installed and rx is enabled, if an rx
interrupt comes before hardware init, rx->cur will be updated. Then the
hardware init will reset BD and make rx->cur out of sync, move the hardware
init code before request_irq.
Signed-off-by: Xiaotian Feng <xiaotian.feng@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
powerpc: fix linkstation and storcenter compilation breakage
Defining flash partition table in platform code is deprecated, and due to
recent changes linkstation and storcenter do not compile any more with
their default configurations because of undefined references to
physmap_set_partitions(). Instead of fixing them by using the correct
kernel configuration macro in preprocessor conditional, remove partition
table definitions altogether. Instead add support for partition definition
on the command-line and in device tree to the default configurations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Wed, 4 Mar 2009 20:55:30 +0000 (14:55 -0600)]
powerpc: add fsl,fifo-depth property to Freescale SSI device nodes
The Freescale Serial Synchronous Interface (SSI) is an audio device present on
some Freescale SOCs. Various implementations of the SSI have a different
transmit and receive FIFO depth, but are otherwise identical. To support
these variations, add a new property fsl,fifo-depth to the SSI node that
specifies the depth of the FIFOs.
Also update the MPC8610 HPCD device tree with this property.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Chris Mason [Mon, 9 Mar 2009 15:45:38 +0000 (11:45 -0400)]
Btrfs: fix spinlock assertions on UP systems
btrfs_tree_locked was being used to make sure a given extent_buffer was
properly locked in a few places. But, it wasn't correct for UP compiled
kernels.
This switches it to using assert_spin_locked instead, and renames it to
btrfs_assert_tree_locked to better reflect how it was really being used.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Reason for this is that cpu time accounting usually only happens from
interrupt context, but acct_update_integrals gets also called from
process context with interrupts enabled.
So in acct_update_integrals we may end up with the following scenario:
Between reading tsk->stime/tsk->utime and tsk->acct_timexpd an interrupt
happens which updates accouting values. This causes acct_timexpd to be
greater than the former stime + utime. The subsequent calculation of
dtime = cputime_sub(time, tsk->acct_timexpd);
will be negative and the division performed by
cputime_to_jiffies(dtime)
will generate an exception since the result won't fit into a 32 bit
register.
In order to fix this just always disable interrupts while accessing any
of the accounting values.
Reported by: Frans Pop <elendil@planet.nl>
Tested by: Frans Pop <elendil@planet.nl> Cc: stable@kernel.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kumar Gala [Wed, 11 Feb 2009 04:26:06 +0000 (22:26 -0600)]
powerpc/fsl-booke: Add support for tlbilx instructions
The e500mc core supports the new tlbilx instructions that do core
local invalidates and also provide us the ability to take down
all TLB entries matching a given PID.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Thu, 19 Feb 2009 16:02:23 +0000 (19:02 +0300)]
powerpc/83xx: Do not configure or probe disabled FSL DR USB controllers
On MPC837X CPUs Dual-Role USB isn't always available (for example DR
USB pins can be muxed away to eSDHC).
U-Boot adds status = "disabled" property into the DR USB nodes to
indicate that we must not try to configure or probe Dual-Role USB,
otherwise we'll break eSDHC support on targets with MPC837X CPUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/83xx: Fix the interrupt loss problem on ipic
The interrupt pending register is write 1 clear. If there are more than
one external interrupts pending at the same time, acking the first
interrupt by reading pending register then OR the corresponding bit and
write back to pending register will also clear other interrupt pending
bits. That will cause loss of interrupt.
Signed-off-by: Da Yu <dayu@datangmobile.cn> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Fri, 6 Feb 2009 14:00:37 +0000 (08:00 -0600)]
i2c-mpc: do not allow interruptions when waiting for I2C to complete
The i2c_wait() function is using wait_event_interruptible_timeout() to wait for
the I2C controller to signal that it has completed an I2C bus operation. If
the process that causes the I2C operation terminated abruptly, the wait will
be interrupted, returning an error. It is better to let the I2C operation
finished before the process exits.
It is safe to use wait_event_timeout() instead, because the timeout will allow
the process to exit if the I2C bus hangs. It's also better to allow the
I2C operation to finish, because unacknowledged I2C operations can cause the
I2C bus to hang.
Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Randy Dunlap [Sat, 28 Feb 2009 16:40:18 +0000 (17:40 +0100)]
ALSA: Move ALSA docbooks to be with the rest of the kernel docbooks
Move ALSA docbooks to be with the rest of the kernel docbooks and add
them to the Makefile so that they build. Latter required a few minor
changes to alsa .tmpl files.
(I did not remove all of the trailing whitespace in the .tmpl files.)
Takashi Iwai [Mon, 23 Feb 2009 15:35:21 +0000 (16:35 +0100)]
ALSA: Clean up snd_monitor_file management
Use the standard linked list for snd_monitor_file management.
Also, move the list deletion of shutdown_list element into
snd_disconnect_release() (for simplification).
Takashi Iwai [Fri, 16 Jan 2009 17:15:22 +0000 (18:15 +0100)]
ALSA: add snd_ctl_add_slave_uncached()
Added snd_ctl_add_slave_uncached() function to add a slave element
with volatile controls. The values of normal slave elements are
supposed to be cachable, i.e. they are changed only via the put
callbacks. OTOH, when a slave element is volatile and its values may
be changed by other reason (e.g. hardware status change), the values
will get inconsistent.
The new function allows the slave elements with volatile changes.
When the slave is tied with this call, the native get callback is
issued at each time so that the values are always updated.
Eric Miao [Tue, 20 Jan 2009 02:31:55 +0000 (10:31 +0800)]
[ARM] pxa: move pxa2xx chip selects definitions out of pxa-regs.h
The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should
be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip
selects definitions are added into pxa3xx-regs.h.
Eric Miao [Mon, 19 Jan 2009 09:34:27 +0000 (17:34 +0800)]
[ARM] pxa: move PCMCIA definitions out of pxa-regs.h into pxa2xx_base.c
Move the processor specific initialization (largely resources initialization)
out of soc_common_drv_pcmcia_probe() into dedicated sa11xx_drv_pcmcia_probe()
and __pxa2xx_drv_pcmcia_probe().
By doing this, we are now able to move the PCMCIA related definitions out of
pxa-regs.h and back into pxa2xx_base.c.
As a result, remove that reference of _PCMCIA1IO in arch/arm/mach-pxa/viper.c.
BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
NOTE:
BANK 3 is only available on PXA27x and later processors.
BANK 4 and 5 are only available on PXA935
1. introduce GPIO_BANK(n) for the offset base of each bank
2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
setings, and saved register values as well, and is dynamically
allocated due to possible bank number ranging from 3 to 6
3. all accesses to GPIO registers are made through 'regbase' within
'pxa_gpio_chip', and register offset
4. introduce several inline functions to simplify the code a bit
5. change IRQ demux handler to base on gpio chips
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Eric Miao [Tue, 6 Jan 2009 10:06:25 +0000 (18:06 +0800)]
[ARM] pxa: move pxa_gpio_mode() outside of generic gpio.c
Looks like we have to live with pxa_gpio_mode() for a while, giving
its presence is actually making gpio.c not generic enough, let's
move it temporarily outside before it can be fully purged.
Eric Miao [Fri, 2 Jan 2009 11:38:42 +0000 (19:38 +0800)]
[ARM] pxa: move DMA registers definitions into <mach/dma.h>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Eric Miao [Fri, 2 Jan 2009 15:17:22 +0000 (23:17 +0800)]
[ARM] pxa: introduce pxa{25x,27x,300,320,930}.h for board usage
Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:
<mach/pxa25x.h> - for pxa25x based platforms
<mach/pxa27x.h> - for pxa27x based platforms
<mach/pxa300.h> - for pxa300 based platforms
<mach/pxa320.h> - for pxa320 based platforms
<mach/pxa930.h> - for pxa930 based platforms
NOTE:
1. one header one board file, they are not compatible (i.e. they have
conflicting definitions which won't compile if included together).
2. Unless strictly necessary, the following header files are considered
to be SoC files use _only_, and is not recommended to be included in
board code:
Takashi Iwai [Tue, 3 Mar 2009 16:00:15 +0000 (17:00 +0100)]
ALSA: Rewrite hw_ptr updaters
Clean up and improve snd_pcm_update_hw_ptr*() functions.
snd_pcm_update_hw_ptr() tries to detect the unexpected hwptr jumps
more strictly to avoid the position mess-up, which often results in
the bad quality I/O with pulseaudio.
The hw-ptr skip error messages are printed when xrun proc is set to
non-zero.
Daniel Mack [Mon, 9 Mar 2009 01:13:17 +0000 (02:13 +0100)]
ASoC: Add a driver for AK4104 S/PDIF transmitter
This adds a driver for the SPI connected AK4104 S/PDIF transmitter
device. Its features are fairly simple, but as there is need to set up
certain bits in the IEC958 information, this better goes into a real
driver.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
KOSAKI Motohiro [Mon, 9 Mar 2009 09:15:34 +0000 (18:15 +0900)]
tracing: Don't use tracing_record_cmdline() in workqueue tracer
Impact: improve workqueue tracer output
Currently, /sys/kernel/debug/tracing/trace_stat/workqueues can display
wrong and strange thread names.
Why?
Currently, ftrace has tracing_record_cmdline()/trace_find_cmdline()
convenience function that implements a task->comm string cache.
This can avoid unnecessary memcpy overhead and the workqueue tracer
uses it.
However, in general, any trace statistics feature shouldn't use
tracing_record_cmdline() because trace statistics can display
very old process. Then comm cache can return wrong string because
recent process overrides the cache.
Fortunately, workqueue trace guarantees that displayed processes
are live. Thus we can search comm string from PID at display time.
<before>
% cat workqueues
# CPU INSERTED EXECUTED NAME
# | | | |
Stuart Bennett [Sun, 8 Mar 2009 18:21:35 +0000 (20:21 +0200)]
x86 mmiotrace: fix remove_kmmio_fault_pages()
Impact: fix race+crash in mmiotrace
The list manipulation in remove_kmmio_fault_pages() was broken. If more
than one consecutive kmmio_fault_page was re-added during the grace
period between unregister_kmmio_probe() and remove_kmmio_fault_pages(),
the list manipulation failed to remove pages from the release list.
After a second grace period the pages get into rcu_free_kmmio_fault_pages()
and raise a BUG_ON() kernel crash.
The list manipulation is fixed to properly remove pages from the release
list.
This bug has been present from the very beginning of mmiotrace in the
mainline kernel. It was introduced in 0fd0e3da ("x86: mmiotrace full
patch, preview 1");
An urgent fix for Linus. Tested by Stuart (on 32-bit) and Pekka
(on amd and intel 64-bit systems, nouveau and nvidia proprietary).
Signed-off-by: Stuart Bennett <stuart@freedesktop.org> Signed-off-by: Pekka Paalanen <pq@iki.fi>
LKML-Reference: <20090308202135.34933feb@daedalus.pq.iki.fi> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Daniel Mack [Sun, 8 Mar 2009 16:51:52 +0000 (17:51 +0100)]
ASoC: bring cs4270 feature/limitations list in sync
Removes numbers from the list of features/limitations and makes it
reflect recent changes to the code.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Sun, 8 Mar 2009 17:27:13 +0000 (10:27 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pebs: correct qualifier passed to ds_write_config() from ds_request_pebs()
x86, bts: remove bad warning
x86: add Dell XPS710 reboot quirk
x86, math-emu: fix init_fpu for task != current
x86: EFI: Back efi_ioremap with init_memory_mapping instead of FIX_MAP
x86: fix DMI on EFI
Linus Torvalds [Sun, 8 Mar 2009 17:24:39 +0000 (10:24 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (28 commits)
Blackfin arch: SPI_MMC is now mainlined MMC_SPI
Blackfin arch: disable legacy /proc/scsi/ support by default
Blackfin arch: remove duplicated ANOMALY_05000448 ifdef check
Blackfin arch: add stubs for anomalies 447 and 448
Blackfin arch: cleanup bfin_sport.h header and export it to userspace
Blackfin arch: fix bug - gdb signull case make trunk kernel panic frequently
Blackfin arch: remove spurious dash when dcache is off
Blackfin arch: mark init_pda as __init as only __init funcs all it
Blackfin arch: fix bug - On bf548-ezkit, ethernet fails to work after wakeup from "mem"
Blackfin arch: Random read/write errors are a bad thing
Blackfin arch: update default kernel config, select KSZ8893M driver for BF518
Blackfin arch: Fix bug - KGDB single step into the middle of a 4 bytes instruction on bf561 after soft bp is hit
Blackfin arch: Fix bug - make ksz8893m driver available when bfin_mac is enabled
Blackfin arch: make sure people do not set the kernel load address too high
Blackfin arch: fix bug - The SPORT_HYS bit is not set for BF561 0.5
Blackfin arch: update anomaly sheets to match latest public info
Blackfin arch: Fix BUG - kernel fails to build in pm.c when allow wakeup fromi standby by GPIO
Blackfin arch: PM_BFIN_WAKE_GP: update help
Blackfin arch: fix bug - kgdb fails to continue after setting breakpoint on bf561-ezkit kernel with smp patch
Blackfin arch: Enable Write Back Cache on all Blackfin Boards
...
Linus Torvalds [Sun, 8 Mar 2009 17:23:05 +0000 (10:23 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmatest: fix use after free in dmatest_exit
ipu_idmac: fix spinlock type
iop-adma, mv_xor: fix mem leak on self-test setup failure
fsldma: fix off by one in dma_halt
I/OAT: fail self-test if callback test reaches timeout
I/OAT: update driver version and copyright dates
I/OAT: list usage cleanup
I/OAT: set tcp_dma_copybreak to 256k for I/OAT ver.3
I/OAT: cancel watchdog before dma remove
I/OAT: fail initialization on zero channels detection
I/OAT: do not set DCACTRL_CMPL_WRITE_ENABLE for I/OAT ver.3
I/OAT: add verification for proper APICID_TAG_MAP setting by BIOS
dmaengine: update kerneldoc
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ata: add CFA specific identify data words
remove stale comment from <linux/hdreg.h>
AT91: initialize Compact Flash on AT91SAM9263 cpu
ide: add at91_ide driver
ide: allow to wrap interrupt handler
ide-iops: fix odd-length ATAPI PIO transfers
ide: NULL noise: drivers/ide/ide-*.c
ide: expiry() returns int, negative expiry() return values won't be noticed
Linus Torvalds [Sun, 8 Mar 2009 17:22:01 +0000 (10:22 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Don't trust current capacity values in identify words 57-58
libata: make sure port is thawed when skipping resets
sata_nv: fix module parameter description
ahci: Add the Device IDs for MCP89 and remove IDs of MCP7B to/from ahci.c
libata: don't use on-stack sense buffer
libata: align ap->sector_buf
libata: fix dma_unmap_sg misuse
libata: change drive ready wait after hard reset to 5s
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
Squashfs: frag_size should be signed, as it can hold an error result
Squashfs: fix documentation typo, Cramfs filesystem limit is 256 MiB
Squashfs: Fix oops when reading fsfuzzer corrupted filesystems
Linus Torvalds [Sun, 8 Mar 2009 17:03:31 +0000 (10:03 -0700)]
Merge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix headphone-detect regression with multiple HP jacks
ALSA: hda - Fix typos in slave controls in patch_sigmatel.c
Ralf Baechle [Thu, 5 Mar 2009 10:45:48 +0000 (11:45 +0100)]
MIPS: compat: Implement is_compat_task.
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall
hole" (commit 5b1017404aea6d2e552e991b3fd814d839e9cd67). MIPS doesn't
have the issue that was fixed for x86-64 by that patch.
This also doesn't solve the N32 issue which is that N32 seccomp processes
will be treated as non-compat processes thus only have access to N64
syscalls.
Ben Dooks [Fri, 12 Dec 2008 00:24:34 +0000 (00:24 +0000)]
[ARM] S3C: Do not kmalloc/kfree during inner suspend code.
The PM CRC checking code kmallocs an area to save a set of
CRC values during suspend. This triggers a warning due to the
call of a function that might sleep whilst the system is not
in a valid state to do so.
Move the allocation and free to points in the suspend and resume
process where they can call a function that might-sleep.
Ben Dooks [Fri, 12 Dec 2008 00:24:36 +0000 (00:24 +0000)]
[ARM] S3C: Avoid checking the task stackpage in pm-check
When doing the CRC check of the memory, avoid checking
the page that our stack is residing in as this changes
during the execution of the suspend and resume.
projects / linux-2.6-omap-h63xx.git / log