Steven Rostedt [Sat, 14 Feb 2009 05:40:25 +0000 (00:40 -0500)]
ftrace: add command interface for function selection
Allow for other tracers to add their own commands for function
selection. This interface gives a trace the ability to name a
command for function selection. Right now it is pretty limited
in what it offers, but this is a building step for more features.
The :mod: command is converted to this interface and also serves
as a template for other implementations.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Krzysztof Helt [Mon, 16 Feb 2009 20:38:37 +0000 (21:38 +0100)]
ALSA: cs4236: cs4232 and cs4236 driver merge to solve PnP BIOS detection
cs4232 and cs4236 driver merge to solve PnP BIOS detection.
Also, the patch adds recognition if the chip is cs4236b+
or earlier part. This unifies drivers for both cs4232
and cs4236+ chips. It allows to use the PnP BIOS
detection for the cs4236+ chips. Previously, only
the snd-cs4232 could be detected by the PnP BIOS.
The cs4232+ cards reports two separate PnP BIOS ids.
The patch adds search for the second id to find out
resources assigned to a control port.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steven Rostedt [Sat, 14 Feb 2009 01:53:42 +0000 (20:53 -0500)]
ftrace: enable filtering only when a function is filtered on
Impact: fix to prevent empty set_ftrace_filter and no ftrace output
The function filter is used to only trace a given set of functions.
The filter is enabled when a function name is echoed into the
set_ftrace_filter file. But if the name has a typo and the function
is not found, the filter is enabled, but no function is listed.
This makes a confusing situation where set_ftrace_filter is empty
but no functions ever get enabled for tracing.
This patch changes that to only enable filtering if a function
is set to be filtered on. Now, the filter is not enabled if
a bad name is echoed into set_ftrace_filter.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
ALSA: usb-audio - Workaround for misdetected sample rate with CM6207
The CM6207 incorrectly advertises its 96 kHz playback setting as 48 kHz
in its USB device descriptor. This patch extends an existing workaround
in usbaudio.c to also cover the CM6207.
This resolves issue 0004249 in the ALSA bug tracker.
Steven Rostedt [Fri, 13 Feb 2009 20:56:43 +0000 (15:56 -0500)]
ftrace: break up ftrace_match_records into smaller components
Impact: clean up
ftrace_match_records does a lot of things that other features
can use. This patch breaks up ftrace_match_records and pulls
out ftrace_setup_glob and ftrace_match_record.
ftrace_setup_glob prepares a simple glob expression for use with
ftrace_match_record. ftrace_match_record compares a single record
with a glob type.
Breaking this up will allow for more features to run on individual
records.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Gregory CLEMENT [Mon, 16 Feb 2009 20:21:47 +0000 (21:21 +0100)]
[ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device controller
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Steven Rostedt [Fri, 13 Feb 2009 19:37:33 +0000 (14:37 -0500)]
ftrace: rename ftrace_match to ftrace_match_records
Impact: clean up
ftrace_match is too generic of a name. What it really does is
search all records and matches the records with the given string,
and either sets or unsets the functions to be traced depending
on if the parameter 'enable' is set or not.
This allows us to make another function called ftrace_match that
can be used to test a single record.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Steven Rostedt [Fri, 13 Feb 2009 17:43:56 +0000 (12:43 -0500)]
ftrace: add do_for_each_ftrace_rec and while_for_each_ftrace_rec
Impact: clean up
To iterate over all the functions that dynamic trace knows about
it requires two for loops. One to iterate over the pages and the
other to iterate over the records within the page.
There are several duplications of these loops in ftrace.c. This
patch creates the macros do_for_each_ftrace_rec and
while_for_each_ftrace_rec to handle this logic, and removes the
duplicate code.
While making this change, I also discovered and fixed a small
bug that one of the iterations should exit the loop after it found the
record it was searching for. This used a break when it should have
used a goto, since there were two loops it needed to break out
from. No real harm was done by this bug since it would only continue
to search the other records, and the code was in a slow path anyway.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Clemens Ladisch [Mon, 16 Feb 2009 14:22:39 +0000 (15:22 +0100)]
sound: usb-audio: fix uninitialized variable with M-Audio MIDI interfaces
Fix the snd_usbmidi_create_endpoints_midiman() function, which forgot to
set the out_interval member of the endpoint info structure for Midiman/
M-Audio devices. Since kernel 2.6.24, any non-zero value makes the
driver use interrupt transfers instead of bulk transfers. With EHCI
controllers, these random interval values result in unbearably large
latencies for output MIDI transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: David <devurandom@foobox.com> Tested-by: David <devurandom@foobox.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Force speaker pin config with model=hp-dv5 model for cases when bios
doesn't set it up properly. All reported hp laptops using model=hp-dv5
model have speaker at pin 0x0d with same config, so it's safe to add
this within hp-dv5 model.
Reference: alsa-devel mailing list thread on
http://mailman.alsa-project.org/pipermail/alsa-devel/2009-February/014390.html
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tobias Diedrich [Mon, 16 Feb 2009 08:13:20 +0000 (00:13 -0800)]
net: forcedeth: Fix wake-on-lan regression
Commit f55c21fd9a92a444e55ad1ca4e4732d56661bf2e ("forcedeth: call
restore mac addr in nv_shutdown path"), which was introduced to fix
the regression tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=11358 causes the
wake-on-lan mac to be reversed in the shutdown path. Apparently the
forcedeth situation is rather messy in that the mac we need to
writeback for a subsequent modprobe to work is exactly the reverse of
what is needed for proper wake-on-lan.
The following patch explains the situation in the comments and
makes the call to nv_restore_mac_addr() conditional (only called if
we are not really going for poweroff).
Tobias Diedrich wrote:
> Hmm, I had not tried WOL for some time.
> With 2.6.29-rc3 is see the following behaviour:
>
> State WOL Behaviour
> ------------------------------
> shutdown reversed MAC
> disk/shutdown reversed MAC
> disk/platform OK
>
> Apparently nv_restore_mac_addr() restores the MAC in the wrong order
> for WOL (at least for my PCI_DEVICE_ID_NVIDIA_NVENET_15). platform
> works, because the MAC is not touched in the nv_suspend() path.
>
> A possible fix might be to only call nv_restore_mac_addr() if
> system_state != SYSTEM_POWER_OFF.
With the following patch:
shutdown OK
disk/shutdown OK
disk/platform OK
kexec OK
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de> Tested-by: Philipp Matthias Hahn <pmhahn@titan.lahn.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 13 Feb 2009 08:33:44 +0000 (08:33 +0000)]
sctp: Inherit all socket options from parent correctly.
During peeloff/accept() sctp needs to save the parent socket state
into the new socket so that any options set on the parent are
inherited by the child socket. This was found when the
parent/listener socket issues SO_BINDTODEVICE, but the
data was misrouted after a route cache flush.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 13 Feb 2009 08:33:43 +0000 (08:33 +0000)]
sctp: Fix the RTO-doubling on idle-link heartbeats
SCTP incorrectly doubles rto ever time a Hearbeat chunk
is generated. However RFC 4960 states:
On an idle destination address that is allowed to heartbeat, it is
recommended that a HEARTBEAT chunk is sent once per RTO of that
destination address plus the protocol parameter 'HB.interval', with
jittering of +/- 50% of the RTO value, and exponential backoff of the
RTO if the previous HEARTBEAT is unanswered.
Essentially, of if the heartbean is unacknowledged, do we double the RTO.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Nussbaum [Fri, 13 Feb 2009 08:33:41 +0000 (08:33 +0000)]
sctp: Allow to disable SCTP checksums via module parameter
This is a new version of my patch, now using a module parameter instead
of a sysctl, so that the option is harder to find. Please note that,
once the module is loaded, it is still possible to change the value of
the parameter in /sys/module/sctp/parameters/, which is useful if you
want to do performance comparisons without rebooting.
Computation of SCTP checksums significantly affects the performance of
SCTP. For example, using two dual-Opteron 246 connected using a Gbe
network, it was not possible to achieve more than ~730 Mbps, compared to
941 Mbps after disabling SCTP checksums.
Unfortunately, SCTP checksum offloading in NICs is not commonly
available (yet).
By default, checksums are still enabled, of course.
Signed-off-by: Lucas Nussbaum <lucas.nussbaum@ens-lyon.fr> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 16 Feb 2009 08:00:20 +0000 (00:00 -0800)]
igb: transition driver to only using advanced descriptors
Currently the driver uses advanced descriptors for its main functionality,
but then uses legacy when testing. This patch changes this so that
advanced descriptors are used throughout and all mentions of legacy
descriptors are removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 16 Feb 2009 07:59:44 +0000 (23:59 -0800)]
igb: remove unused defines
This patch removes all of the unused defines from the .h files contained in
igb. For some defines there was a use and so I plugged them into the correct
locations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Feb 2009 14:45:17 +0000 (14:45 +0000)]
igb: misc cleanup to combine one if statement
This patch combines a pair of if statements into one.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 12 Feb 2009 18:17:42 +0000 (18:17 +0000)]
igb: cleanup incorrect comment and set IP Checksum Enable
IP Checksum enable doesn't need packet split in order to function. It only
requires the use of advanced descriptors which the current igb driver does.
So we can enable it always without any issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 12 Feb 2009 18:17:21 +0000 (18:17 +0000)]
igb: reduce size required to trigger low latency
Update the Adaptive Interrupt Moderation algorithm so that the low latency
state is triggered less easily to prevent high interrupt loads.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 12 Feb 2009 18:16:59 +0000 (18:16 +0000)]
igb: misc whitespace/formatting cleanups
This patch is intended to hold several whitespace, formatting, and
comment cleanups that have been found while cleaning up the igb driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When testing for a dom0/initial/privileged domain, make sure the
predicate evaluates to a compile-time 0 if CONFIG_XEN_DOM0 isn't
enabled. This will make most of the dom0 code evaporate without
much more effort.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
mv643xx_eth: implement ethtool rx/tx ring size query and resizing
Rename the mp->default_[rt]x_ring_size variables to ->[rt]x_ring_size,
allow them to be read via the standard ethtool ->get_ringparam() op,
and add a ->set_ringparam() op to allow resizing them at run time.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mv643xx_eth: rework interrupt coalescing, and export via ethtool
This patch:
- increases the precision of the receive/transmit interrupt
coalescing register value computations by using 64bit temporaries;
- adds functions to read the current hardware coalescing register
values and convert them back to usecs;
- exports the {get,set} {rx,tx} coal methods via the standard
ethtool coalescing interface.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mv643xx_eth: unify ethtool ops for phy'd and phy-less interfaces
It's a waste having two different versions of this structure around
when the differences between ethtool ops for phy'd and phy-less
interfaces are so minor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Thu, 12 Feb 2009 09:32:41 +0000 (09:32 +0000)]
drivers/isdn/mISDN: fix sparse warnings: make symbols static
Fix this sparse warnings:
drivers/isdn/mISDN/clock.c:44:1: warning: symbol 'iclock_lock' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:45:9: warning: symbol 'iclock_count' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:46:17: warning: symbol 'iclock_tv' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:47:9: warning: symbol 'iclock_tv_valid' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:48:20: warning: symbol 'iclock_current' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Thu, 12 Feb 2009 09:28:40 +0000 (09:28 +0000)]
drivers/isdn/hardware/mISDN: fix sparse warnings: make symbols static
Fix this sparse warnings:
drivers/isdn/hardware/mISDN/hfcpci.c:59:19: warning: symbol 'hfc_tl' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcpci.c:60:9: warning: symbol 'hfc_jiffies' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.h:201:6: warning: symbol 'conf_str' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.h:319:12: warning: symbol 'HFC_TE_LAYER1_STATES' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.h:331:12: warning: symbol 'HFC_NT_LAYER1_STATES' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.c:38:12: warning: symbol 'hfcsusb_rev' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.c:978:1: warning: symbol 'fill_isoc_urb' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.c:1724:1: warning: symbol 'setup_hfcsusb' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:38:20 +0000 (08:38 +0000)]
bnx2x: Removing unused struct
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:38:17 +0000 (08:38 +0000)]
bnx2x: Sparse endianity annotation
Resolving the majority of the issues, but there are still some left for future
patches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:38:14 +0000 (08:38 +0000)]
bnx2x: Removing redundant macros
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:37:14 +0000 (08:37 +0000)]
bnx2x: Pre emphasis configuration
Supporting non-default pre-emphasis settings for the internal and some external
PHYs
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:37:09 +0000 (08:37 +0000)]
bnx2x: Removing CL73 code
This code is disabled, so removing it to avoid confusion
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:37:07 +0000 (08:37 +0000)]
bnx2x: Using the HW 5th lane
This 1G interface (on top of the 4 lanes 10G interface) requires additional
setting to work in CL45
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:37:04 +0000 (08:37 +0000)]
bnx2x: EMAC reset
The NIG_ENABLE does not reset the emac. Replace it with explicit reset
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:37:02 +0000 (08:37 +0000)]
bnx2x: Saving PHY FW version
Some PHYs (like the BCM8726) FW version cannot be read after activating the
PHY, so we need to save this information
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:37:00 +0000 (08:37 +0000)]
bnx2x: Supporting BCM8481 PHY
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:36:58 +0000 (08:36 +0000)]
bnx2x: PHY lock list
Some dual port PHY require HW lock since they are used by both interfaces
(different driver instances). Since this list is getting longer, update a
parameter at load time instead of calculating it on runtime
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:36:55 +0000 (08:36 +0000)]
bnx2x: Supporting BCM8726 PHY
Also adding the ability to recognize the optic module and disable it if it is
not authorized for safety reasons - since this feature might upset some users
which are willing to take the risk, it is optional and can be disabled by
setting an nvram bit (or a trivial driver patch to set this bit).
This dual port PHY requires special handling if the ports are swapped.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:36:43 +0000 (08:36 +0000)]
bnx2x: Flow control enhancement
Setting better HW thresholds and enabling FW capabilities for better
enforcement. Also set the HW to more efficiently use the internal buffers if
this is a single port design
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:36:40 +0000 (08:36 +0000)]
bnx2x: BW shaper enhancements
Some of the configuration can be set when loading the device and shouldn't be
re-calculated after each link up indication since it is not dependent on the
link speed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:36:23 +0000 (08:36 +0000)]
bnx2x: Disabling interrupts after iSCSI-boot
Before initializing the chip after iSCSI boot, the interrupts of the function
that was used to boot must be disabled. That means that the driver needs to set
the chip as if it is the iSCSI PCI function - this bug is exposed only with MSI
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 12 Feb 2009 08:36:15 +0000 (08:36 +0000)]
bnx2x: MSI support
Enabling MSI on top of MSI-X and INTA. Also changing the module parameter to
allow choosing INTA or MSI even when MSI-X is available. The default status
block should not be reversed for endianity. Since MSI can issue
re-configuration, the interrupt disable function now requires mmiowb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 16 Feb 2009 07:24:08 +0000 (23:24 -0800)]
bnx2x: New FW
This is the FW blob and the relevant definitions without any logic. It
also contains the minimal mandatory code changes to work with this FW
but it does not contain enabling of the new features that this FW
provides.
This FW is needed for:
- More efficient multi-queue
- per queue statistics
- Big-endian issue with MSI
- Improved pause response
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Ohly [Thu, 12 Feb 2009 05:03:43 +0000 (05:03 +0000)]
igb: use timecompare to implement hardware time stamping
Both TX and RX hardware time stamping are implemented. Due to
hardware limitations it is not possible to verify reliably which
packet was time stamped when multiple were pending for sending; this
could be solved by only allowing one packet marked for hardware time
stamping into the queue (not implemented yet).
RX time stamping relies on the flag in the packet descriptor which
marks packets that were time stamped. In "all packet" mode this flag
is not set. TODO: also support that mode (even though it'll suffer
from race conditions).
Signed-off-by: John Ronciak <john.ronciak@intel.com> Signed-off-by: Patrick Ohly <patrick.ohly@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Ohly [Thu, 12 Feb 2009 05:03:42 +0000 (05:03 +0000)]
igb: stub support for SIOCSHWTSTAMP
Signed-off-by: John Ronciak <john.ronciak@intel.com> Signed-off-by: Patrick Ohly <patrick.ohly@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Ohly [Thu, 12 Feb 2009 05:03:41 +0000 (05:03 +0000)]
igb: access to NIC time
Adds the register definitions and code to read the time
register.
Signed-off-by: John Ronciak <john.ronciak@intel.com> Signed-off-by: Patrick Ohly <patrick.ohly@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: fix powernow-k8 when acpi=off (or other error).
There was a spurious change introduced into powernow-k8 in this patch:
so that we try to "restore" the cpus_allowed we never saved. We revert
that file.
See lkml "[PATCH] x86/powernow: fix cpus_allowed brokage when
acpi=off" from Yinghai for the bug report.
Cc: Mike Travis <travis@sgi.com> Cc: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Ingo Molnar <mingo@elte.hu>
Patrick Ohly [Thu, 12 Feb 2009 05:03:38 +0000 (05:03 +0000)]
net: socket infrastructure for SO_TIMESTAMPING
The overlap with the old SO_TIMESTAMP[NS] options is handled so
that time stamping in software (net_enable_timestamp()) is
enabled when SO_TIMESTAMP[NS] and/or SO_TIMESTAMPING_RX_SOFTWARE
is set. It's disabled if all of these are off.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Ohly [Thu, 12 Feb 2009 05:03:37 +0000 (05:03 +0000)]
net: infrastructure for hardware time stamping
The additional per-packet information (16 bytes for time stamps, 1
byte for flags) is stored for all packets in the skb_shared_info
struct. This implementation detail is hidden from users of that
information via skb_* accessor functions. A separate struct resp.
union is used for the additional information so that it can be
stored/copied easily outside of skb_shared_info.
Compared to previous implementations (reusing the tstamp field
depending on the context, optional additional structures) this
is the simplest solution. It does not extend sk_buff itself.
TX time stamping is implemented in software if the device driver
doesn't support hardware time stamping.
The new semantic for hardware/software time stamping around
ndo_start_xmit() is based on two assumptions about existing
network device drivers which don't support hardware time
stamping and know nothing about it:
- they leave the new skb_shared_tx unmodified
- the keep the connection to the originating socket in skb->sk
alive, i.e., don't call skb_orphan()
Given that skb_shared_tx is new, the first assumption is safe.
The second is only true for some drivers. As a result, software
TX time stamping currently works with the bnx2 driver, but not
with the unmodified igb driver (the two drivers this patch series
was tested with).
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Ohly [Thu, 12 Feb 2009 05:03:36 +0000 (05:03 +0000)]
net: new user space API for time stamping of incoming and outgoing packets
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log