2 * linux/arch/arm/mach-omap2/board-2430sdp.c
4 * Copyright (C) 2006 Texas Instruments
6 * Modified from mach-omap2/board-generic.c
8 * Initial Code : Based on a patch from Komal Shah and Richard Woodruff
9 * Updated the Code for 2430 SDP : Syed Mohammed Khasim
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License version 2 as
13 * published by the Free Software Foundation.
16 #include <linux/kernel.h>
17 #include <linux/init.h>
18 #include <linux/platform_device.h>
19 #include <linux/mtd/mtd.h>
20 #include <linux/mtd/partitions.h>
21 #include <linux/delay.h>
22 #include <linux/input.h>
23 #include <linux/i2c/twl4030.h>
24 #include <linux/err.h>
25 #include <linux/clk.h>
26 #include <linux/spi/spi.h>
27 #include <linux/spi/ads7846.h>
29 #include <mach/hardware.h>
30 #include <asm/mach-types.h>
31 #include <asm/mach/arch.h>
32 #include <asm/mach/map.h>
33 #include <asm/mach/flash.h>
35 #include <mach/gpio.h>
37 #include <mach/board.h>
38 #include <mach/usb-musb.h>
39 #include <mach/hsmmc.h>
40 #include <mach/common.h>
41 #include <mach/keypad.h>
42 #include <mach/gpmc.h>
43 #include <mach/mcspi.h>
47 #define SDP2430_FLASH_CS 0
48 #define SDP2430_SMC91X_CS 5
50 /* GPIO used for TSC2046 (touchscreen)
52 * Also note that the tsc2046 is the same silicon as the ads7846, so
53 * that driver is used for the touchscreen. */
56 #define TWL4030_MSECURE_GPIO 118
57 #define SECONDARY_LCD_GPIO 147
59 static struct mtd_partition sdp2430_partitions[] = {
60 /* bootloader (U-Boot, etc) in first sector */
65 .mask_flags = MTD_WRITEABLE, /* force read-only */
67 /* bootloader params in the next sector */
70 .offset = MTDPART_OFS_APPEND,
77 .offset = MTDPART_OFS_APPEND,
84 .offset = MTDPART_OFS_APPEND,
85 .size = MTDPART_SIZ_FULL,
90 static struct flash_platform_data sdp2430_flash_data = {
91 .map_name = "cfi_probe",
93 .parts = sdp2430_partitions,
94 .nr_parts = ARRAY_SIZE(sdp2430_partitions),
97 static struct resource sdp2430_flash_resource = {
98 .start = SDP2430_CS0_BASE,
99 .end = SDP2430_CS0_BASE + SZ_64M - 1,
100 .flags = IORESOURCE_MEM,
103 static struct platform_device sdp2430_flash_device = {
107 .platform_data = &sdp2430_flash_data,
110 .resource = &sdp2430_flash_resource,
113 static struct resource sdp2430_smc91x_resources[] = {
115 .start = SDP2430_CS0_BASE,
116 .end = SDP2430_CS0_BASE + SZ_64M - 1,
117 .flags = IORESOURCE_MEM,
120 .start = OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
121 .end = OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
122 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
126 static struct platform_device sdp2430_lcd_device = {
127 .name = "sdp2430_lcd",
131 static struct platform_device sdp2430_smc91x_device = {
134 .num_resources = ARRAY_SIZE(sdp2430_smc91x_resources),
135 .resource = sdp2430_smc91x_resources,
139 * Key mapping for 2430 SDP board
142 static int sdp2430_keymap[] = {
144 KEY(0, 1, KEY_RIGHT),
153 KEY(2, 0, KEY_ENTER),
176 static struct omap_kp_platform_data sdp2430_kp_data = {
179 .keymap = sdp2430_keymap,
180 .keymapsize = ARRAY_SIZE(sdp2430_keymap),
182 .irq = TWL4030_MODIRQ_KEYPAD,
185 static struct platform_device sdp2430_kp_device = {
186 .name = "omap_twl4030keypad",
189 .platform_data = &sdp2430_kp_data,
193 static int __init msecure_init(void)
197 #ifdef CONFIG_RTC_DRV_TWL4030
198 ret = gpio_request(TWL4030_MSECURE_GPIO, "msecure");
200 printk(KERN_ERR "msecure_init: can't reserve GPIO:%d !\n",
201 TWL4030_MSECURE_GPIO);
205 * TWL4030 will be in secure mode if msecure line from OMAP is low.
206 * Make msecure line high in order to change the TWL4030 RTC time
207 * and calender registers.
209 gpio_direction_output(TWL4030_MSECURE_GPIO, 1);
216 static struct platform_device *sdp2430_devices[] __initdata = {
217 &sdp2430_smc91x_device,
218 &sdp2430_flash_device,
223 static void ads7846_dev_init(void)
225 if (omap_request_gpio(TS_GPIO) < 0)
226 printk(KERN_ERR "can't get ads746 pen down GPIO\n");
228 omap_set_gpio_direction(TS_GPIO, 1);
230 omap_set_gpio_debounce(TS_GPIO, 1);
231 omap_set_gpio_debounce_time(TS_GPIO, 0xa);
234 static int ads7846_get_pendown_state(void)
236 return !omap_get_gpio_datain(TS_GPIO);
239 static struct ads7846_platform_data tsc2046_config __initdata = {
240 .get_pendown_state = ads7846_get_pendown_state,
244 static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
246 .single_channel = 0, /* 0: slave, 1: master */
249 static struct omap_lcd_config sdp2430_lcd_config __initdata = {
250 .ctrl_name = "internal",
253 static struct spi_board_info sdp2430_spi_board_info[] __initdata = {
256 * TSC2046 operates at a max freqency of 2MHz, so
257 * operate slightly below at 1.5MHz
259 .modalias = "ads7846",
262 .max_speed_hz = 1500000,
263 .controller_data = &tsc2046_mcspi_config,
264 .irq = OMAP_GPIO_IRQ(TS_GPIO),
265 .platform_data = &tsc2046_config,
269 static inline void __init sdp2430_init_smc91x(void)
272 unsigned long cs_mem_base;
274 struct clk *gpmc_fck;
276 eth_cs = SDP2430_SMC91X_CS;
278 gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
279 if (IS_ERR(gpmc_fck)) {
284 clk_enable(gpmc_fck);
285 rate = clk_get_rate(gpmc_fck);
287 /* Make sure CS1 timings are correct, for 2430 always muxed */
288 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
290 if (rate >= 160000000) {
291 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
292 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
293 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
294 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
295 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
296 } else if (rate >= 130000000) {
297 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
298 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
299 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
300 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
301 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
302 } else { /* rate = 100000000 */
303 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
304 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
305 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
306 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
307 gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
310 if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
311 printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
315 sdp2430_smc91x_resources[0].start = cs_mem_base + 0x300;
316 sdp2430_smc91x_resources[0].end = cs_mem_base + 0x30f;
319 if (omap_request_gpio(OMAP24XX_ETHR_GPIO_IRQ) < 0) {
320 printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
321 OMAP24XX_ETHR_GPIO_IRQ);
322 gpmc_cs_free(eth_cs);
325 omap_set_gpio_direction(OMAP24XX_ETHR_GPIO_IRQ, 1);
328 clk_disable(gpmc_fck);
332 static void __init omap_2430sdp_init_irq(void)
334 omap2_init_common_hw(NULL);
337 sdp2430_init_smc91x();
340 static struct omap_uart_config sdp2430_uart_config __initdata = {
341 .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
345 struct omap_serial_console_config sdp2430_serial_console_config __initdata = {
347 .console_speed = 115200,
350 static struct omap_board_config_kernel sdp2430_config[] __initdata = {
351 {OMAP_TAG_UART, &sdp2430_uart_config},
352 {OMAP_TAG_LCD, &sdp2430_lcd_config},
353 {OMAP_TAG_SERIAL_CONSOLE, &sdp2430_serial_console_config},
356 static int __init omap2430_i2c_init(void)
359 * Registering bus 2 first to avoid twl4030 misbehaving as 2430SDP
360 * has twl4030 on bus 2
362 omap_register_i2c_bus(2, 2600, NULL, 0);
363 omap_register_i2c_bus(1, 400, NULL, 0);
367 static void __init omap_2430sdp_init(void)
371 platform_add_devices(sdp2430_devices, ARRAY_SIZE(sdp2430_devices));
372 omap_board_config = sdp2430_config;
373 omap_board_config_size = ARRAY_SIZE(sdp2430_config);
378 sdp2430_flash_init();
381 spi_register_board_info(sdp2430_spi_board_info,
382 ARRAY_SIZE(sdp2430_spi_board_info));
386 /* turn off secondary LCD backlight */
387 omap_set_gpio_direction(SECONDARY_LCD_GPIO, 0);
388 omap_set_gpio_dataout(SECONDARY_LCD_GPIO, 0);
391 static void __init omap_2430sdp_map_io(void)
393 omap2_set_globals_243x();
394 omap2_map_common_io();
397 MACHINE_START(OMAP_2430SDP, "OMAP2430 sdp2430 board")
398 /* Maintainer: Syed Khasim - Texas Instruments Inc */
399 .phys_io = 0x48000000,
400 .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
401 .boot_params = 0x80000100,
402 .map_io = omap_2430sdp_map_io,
403 .init_irq = omap_2430sdp_init_irq,
404 .init_machine = omap_2430sdp_init,
405 .timer = &omap_timer,