2 # Miscellaneous I2C chip drivers configuration
5 menu "Miscellaneous I2C Chip support"
8 tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
9 depends on EXPERIMENTAL
11 If you say yes here you get support for Dallas Semiconductor
12 DS1682 Total Elapsed Time Recorder.
14 This driver can also be built as a module. If so, the module
15 will be called ds1682.
18 tristate "EEPROM reader"
19 depends on EXPERIMENTAL
21 If you say yes here you get read-only access to the EEPROM data
22 available on modern memory DIMMs and Sony Vaio laptops. Such
23 EEPROMs could theoretically be available on other devices as well.
25 This driver can also be built as a module. If so, the module
26 will be called eeprom.
28 config SENSORS_PCF8574
29 tristate "Philips PCF8574 and PCF8574A"
30 depends on EXPERIMENTAL
33 If you say yes here you get support for Philips PCF8574 and
34 PCF8574A chips. These chips are 8-bit I/O expanders for the I2C bus.
36 This driver can also be built as a module. If so, the module
37 will be called pcf8574.
39 These devices are hard to detect and rarely found on mainstream
40 hardware. If unsure, say N.
43 tristate "Philips PCF8575"
46 If you say yes here you get support for Philips PCF8575 chip.
47 This chip is a 16-bit I/O expander for the I2C bus. Several other
48 chip manufacturers sell equivalent chips, e.g. Texas Instruments.
50 This driver can also be built as a module. If so, the module
51 will be called pcf8575.
53 This device is hard to detect and is rarely found on mainstream
54 hardware. If unsure, say N.
56 config SENSORS_PCA9539
57 tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
58 depends on EXPERIMENTAL && GPIO_PCA9539 = "n"
60 If you say yes here you get support for the Philips PCA9539
63 This driver can also be built as a module. If so, the module
64 will be called pca9539.
66 This driver is deprecated and will be dropped soon. Use
67 drivers/gpio/pca9539.c instead.
69 config SENSORS_PCF8591
70 tristate "Philips PCF8591"
71 depends on EXPERIMENTAL
74 If you say yes here you get support for Philips PCF8591 chips.
76 This driver can also be built as a module. If so, the module
77 will be called pcf8591.
79 These devices are hard to detect and rarely found on mainstream
80 hardware. If unsure, say N.
83 tristate "Philips ISP1301 with OMAP OTG"
84 depends on ARCH_OMAP_OTG
86 If you say yes here you get support for the Philips ISP1301
87 USB-On-The-Go transceiver working with the OMAP OTG controller.
88 The ISP1301 is used in products including H2 and H3 development
89 boards for Texas Instruments OMAP processors.
91 This driver can also be built as a module. If so, the module
92 will be called isp1301_omap.
95 tristate "TPS6501x Power Management chips"
96 default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK
98 If you say yes here you get support for the TPS6501x series of
99 Power Management chips. These include voltage regulators,
100 lithium ion/polymer battery charging, and other features that
101 are often used in portable devices like cell phones and cameras.
103 This driver can also be built as a module. If so, the module
104 will be called tps65010.
106 config SENSORS_TLV320AIC23
107 tristate "Texas Instruments TLV320AIC23 Codec"
108 depends on I2C && I2C_OMAP
110 If you say yes here you get support for the I2C control
111 interface for Texas Instruments TLV320AIC23 audio codec.
113 config GPIOEXPANDER_OMAP
114 bool "GPIO Expander PCF8574PWR for OMAP"
115 depends on I2C && (ARCH_OMAP16XX || ARCH_OMAP24XX)
117 If you say yes here you get support for I/O expander calls
118 to configure IrDA, Camera and audio devices.
121 bool "TI's TWL4030 companion chip Core Driver Support"
122 depends on I2C=y && (ARCH_OMAP24XX || ARCH_OMAP34XX)
124 Say yes here if you have TWL4030 chip on your board
127 bool "TWL4030 GPIO Driver"
128 depends on TWL4030_CORE
131 bool "TWL4030 USB Transceiver Driver"
132 depends on TWL4030_CORE
135 prompt "Transceiver mode"
136 depends on TWL4030_USB
138 TWL4030 USB transceiver can operate in various
139 mutually-exclusive modes. Select one of them.
141 config TWL4030_USB_HS_ULPI
142 depends on TWL4030_USB
143 bool "High-speed ULPI"
145 Say Y here if the TWL4030 is connected to high-speed USB
146 controller through a ULPI interface.
150 config TWL4030_POWEROFF
151 bool "TWL4030 device poweroff"
152 depends on TWL4030_CORE
154 config SENSORS_MAX6875
155 tristate "Maxim MAX6875 Power supply supervisor"
156 depends on EXPERIMENTAL
158 If you say yes here you get support for the Maxim MAX6875
159 EEPROM-programmable, quad power-supply sequencer/supervisor.
161 This provides an interface to program the EEPROM and reset the chip.
163 This driver also supports the Maxim MAX6874 hex power-supply
164 sequencer/supervisor if found at a compatible address.
166 This driver can also be built as a module. If so, the module
167 will be called max6875.
169 config SENSORS_TSL2550
170 tristate "Taos TSL2550 ambient light sensor"
171 depends on EXPERIMENTAL
173 If you say yes here you get support for the Taos TSL2550
174 ambient light sensor.
176 This driver can also be built as a module. If so, the module
177 will be called tsl2550.
180 bool "TWL92330/Menelaus PM chip"
181 depends on I2C=y && ARCH_OMAP24XX
183 If you say yes here you get support for the Texas Instruments
184 TWL92330/Menelaus Power Management chip. This include voltage
185 regulators, Dual slot memory card tranceivers, real-time clock
186 and other features that are often used in portable devices like
187 cell phones and PDAs.