2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_ADS7846
15 tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
17 depends on HWMON = n || HWMON
19 Say Y here if you have a touchscreen interface using the
20 ADS7846/TSC2046 or ADS7843 controller, and your board-specific
21 setup code includes that in its table of SPI devices.
23 If HWMON is selected, and the driver is told the reference voltage
24 on your board, you will also get hwmon interfaces for the voltage
25 (and on ads7846/tsc2046, temperature) sensors of this chip.
27 If unsure, say N (but it's safe to say "Y").
29 To compile this driver as a module, choose M here: the
30 module will be called ads7846.
32 config TOUCHSCREEN_BITSY
33 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
34 depends on SA1100_BITSY
37 Say Y here if you have the h3600 (Bitsy) touchscreen.
41 To compile this driver as a module, choose M here: the
42 module will be called h3600_ts_input.
44 config TOUCHSCREEN_CORGI
45 tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
46 depends on PXA_SHARPSL
49 Say Y here to enable the driver for the touchscreen on the
50 Sharp SL-C7xx and SL-Cxx00 series of PDAs.
54 To compile this driver as a module, choose M here: the
55 module will be called corgi_ts.
57 config TOUCHSCREEN_FUJITSU
58 tristate "Fujitsu serial touchscreen"
61 Say Y here if you have the Fujitsu touchscreen (such as one
62 installed in Lifebook P series laptop) connected to your
67 To compile this driver as a module, choose M here: the
68 module will be called fujitsu-ts.
70 config TOUCHSCREEN_GUNZE
71 tristate "Gunze AHL-51S touchscreen"
74 Say Y here if you have the Gunze AHL-51 touchscreen connected to
79 To compile this driver as a module, choose M here: the
80 module will be called gunze.
82 config TOUCHSCREEN_ELO
83 tristate "Elo serial touchscreens"
86 Say Y here if you have an Elo serial touchscreen connected to
91 To compile this driver as a module, choose M here: the
92 module will be called elo.
94 config TOUCHSCREEN_MTOUCH
95 tristate "MicroTouch serial touchscreens"
98 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
103 To compile this driver as a module, choose M here: the
104 module will be called mtouch.
106 config TOUCHSCREEN_MK712
107 tristate "ICS MicroClock MK712 touchscreen"
109 Say Y here if you have the ICS MicroClock MK712 touchscreen
110 controller chip in your system.
114 To compile this driver as a module, choose M here: the
115 module will be called mk712.
117 config TOUCHSCREEN_HP600
118 tristate "HP Jornada 6xx touchscreen"
119 depends on SH_HP6XX && SH_ADC
121 Say Y here if you have a HP Jornada 620/660/680/690 and want to
122 support the built-in touchscreen.
124 To compile this driver as a module, choose M here: the
125 module will be called hp680_ts_input.
127 config TOUCHSCREEN_HP7XX
128 tristate "HP Jornada 7xx touchscreen"
129 depends on SA1100_JORNADA720_SSP
131 Say Y here if you have a HP Jornada 710/720/728 and want
132 to support the built-in touchscreen.
134 To compile this driver as a module, choose M here: the
135 module will be called jornada720_ts.
137 config TOUCHSCREEN_PENMOUNT
138 tristate "Penmount serial touchscreen"
141 Say Y here if you have a Penmount serial touchscreen connected to
146 To compile this driver as a module, choose M here: the
147 module will be called penmount.
149 config TOUCHSCREEN_TOUCHRIGHT
150 tristate "Touchright serial touchscreen"
153 Say Y here if you have a Touchright serial touchscreen connected to
158 To compile this driver as a module, choose M here: the
159 module will be called touchright.
161 config TOUCHSCREEN_TOUCHWIN
162 tristate "Touchwin serial touchscreen"
165 Say Y here if you have a Touchwin serial touchscreen connected to
170 To compile this driver as a module, choose M here: the
171 module will be called touchwin.
173 config TOUCHSCREEN_UCB1400
174 tristate "Philips UCB1400 touchscreen"
177 This enables support for the Philips UCB1400 touchscreen interface.
178 The UCB1400 is an AC97 audio codec. The touchscreen interface
179 will be initialized only after the ALSA subsystem has been
180 brought up and the UCB1400 detected. You therefore have to
181 configure ALSA support as well (either built-in or modular,
182 independently of whether this driver is itself built-in or
183 modular) for this driver to work.
185 To compile this driver as a module, choose M here: the
186 module will be called ucb1400_ts.
188 config TOUCHSCREEN_TSC2102
189 tristate "TSC 2102 based touchscreens"
190 depends on SPI_MASTER
193 Say Y here if you have a touchscreen interface using the
194 TI TSC 2102 controller, and your board-specific initialization
195 code includes that in its table of SPI devices. Also make
196 sure the proper SPI controller is selected.
198 If unsure, say N (but it's safe to say "Y").
200 To compile this driver as a module, choose M here: the
201 module will be called tsc2102_ts.
203 config TOUCHSCREEN_TSC210X
204 tristate "TI TSC210x based touchscreens"
205 depends on SPI_MASTER
208 Say Y here if you have a touchscreen interface using a
209 TI TSC210x controller, and your board-specific initialisation
210 code includes that in its table of SPI devices.
212 If unsure, say N (but it's safe to say "Y").
214 To compile this driver as a module, choose M here: the
215 module will be called tsc210x_ts.
217 config TOUCHSCREEN_TSC2301
218 tristate "TSC2301 touchscreen support"
219 depends on SPI_TSC2301
221 Say Y here for if you are using the touchscreen features of TSC2301.
223 config TOUCHSCREEN_USB_COMPOSITE
224 tristate "USB Touchscreen Driver"
225 depends on USB_ARCH_HAS_HCD
228 USB Touchscreen driver for:
229 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
230 - PanJit TouchSet USB
231 - 3M MicroTouch USB (EX II series)
233 - some other eTurboTouch
236 - IRTOUCHSYSTEMS/UNITOP
238 - GoTop Super_Q2/GogoPen/PenPower tablets
240 Have a look at <http://linux.chapter7.ch/touchkit/> for
241 a usage description and the required user-space stuff.
243 To compile this driver as a module, choose M here: the
244 module will be called usbtouchscreen.
246 config TOUCHSCREEN_USB_EGALAX
248 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
249 depends on TOUCHSCREEN_USB_COMPOSITE
251 config TOUCHSCREEN_USB_PANJIT
253 bool "PanJit device support" if EMBEDDED
254 depends on TOUCHSCREEN_USB_COMPOSITE
256 config TOUCHSCREEN_USB_3M
258 bool "3M/Microtouch EX II series device support" if EMBEDDED
259 depends on TOUCHSCREEN_USB_COMPOSITE
261 config TOUCHSCREEN_USB_ITM
263 bool "ITM device support" if EMBEDDED
264 depends on TOUCHSCREEN_USB_COMPOSITE
266 config TOUCHSCREEN_USB_ETURBO
268 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
269 depends on TOUCHSCREEN_USB_COMPOSITE
271 config TOUCHSCREEN_USB_GUNZE
273 bool "Gunze AHL61 device support" if EMBEDDED
274 depends on TOUCHSCREEN_USB_COMPOSITE
276 config TOUCHSCREEN_USB_DMC_TSC10
278 bool "DMC TSC-10/25 device support" if EMBEDDED
279 depends on TOUCHSCREEN_USB_COMPOSITE
281 config TOUCHSCREEN_USB_IRTOUCH
283 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
284 depends on TOUCHSCREEN_USB_COMPOSITE
286 config TOUCHSCREEN_USB_IDEALTEK
288 bool "IdealTEK URTC1000 device support" if EMBEDDED
289 depends on TOUCHSCREEN_USB_COMPOSITE
291 config TOUCHSCREEN_USB_GENERAL_TOUCH
293 bool "GeneralTouch Touchscreen device support" if EMBEDDED
294 depends on TOUCHSCREEN_USB_COMPOSITE
296 config TOUCHSCREEN_USB_GOTOP
298 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
299 depends on TOUCHSCREEN_USB_COMPOSITE