2 * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
3 * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
4 * Copyright (c) 2007-2008 Luis Rodriguez <mcgrof@winlab.rutgers.edu>
5 * Copyright (c) 2007-2008 Pavel Roskin <proski@gnu.org>
6 * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com>
8 * Permission to use, copy, modify, and distribute this software for any
9 * purpose with or without fee is hereby granted, provided that the above
10 * copyright notice and this permission notice appear in all copies.
12 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
13 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
14 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
15 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
16 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
17 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
18 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
24 /*****************************\
25 Reset functions and helpers
26 \*****************************/
28 #include <linux/pci.h>
35 * ath5k_hw_write_ofdm_timings - set OFDM timings on AR5212
37 * @ah: the &struct ath5k_hw
38 * @channel: the currently set channel upon reset
40 * Write the OFDM timings for the AR5212 upon reset. This is a helper for
41 * ath5k_hw_reset(). This seems to tune the PLL a specified frequency
42 * depending on the bandwidth of the channel.
45 static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw *ah,
46 struct ieee80211_channel *channel)
48 /* Get exponent and mantissa and set it */
49 u32 coef_scaled, coef_exp, coef_man,
50 ds_coef_exp, ds_coef_man, clock;
52 if (!(ah->ah_version == AR5K_AR5212) ||
53 !(channel->hw_value & CHANNEL_OFDM))
56 /* Seems there are two PLLs, one for baseband sampling and one
57 * for tuning. Tuning basebands are 40 MHz or 80MHz when in
59 clock = channel->hw_value & CHANNEL_TURBO ? 80 : 40;
60 coef_scaled = ((5 * (clock << 24)) / 2) /
63 for (coef_exp = 31; coef_exp > 0; coef_exp--)
64 if ((coef_scaled >> coef_exp) & 0x1)
70 coef_exp = 14 - (coef_exp - 24);
71 coef_man = coef_scaled +
72 (1 << (24 - coef_exp - 1));
73 ds_coef_man = coef_man >> (24 - coef_exp);
74 ds_coef_exp = coef_exp - 16;
76 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_3,
77 AR5K_PHY_TIMING_3_DSC_MAN, ds_coef_man);
78 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_TIMING_3,
79 AR5K_PHY_TIMING_3_DSC_EXP, ds_coef_exp);
86 * index into rates for control rates, we can set it up like this because
87 * this is only used for AR5212 and we know it supports G mode
89 static int control_rates[] =
90 { 0, 1, 1, 1, 4, 4, 6, 6, 8, 8, 8, 8 };
93 * ath5k_hw_write_rate_duration - set rate duration during hw resets
95 * @ah: the &struct ath5k_hw
96 * @mode: one of enum ath5k_driver_mode
98 * Write the rate duration table upon hw reset. This is a helper for
99 * ath5k_hw_reset(). It seems all this is doing is setting an ACK timeout for
100 * the hardware for the current mode for each rate. The rates which are capable
101 * of short preamble (802.11b rates 2Mbps, 5.5Mbps, and 11Mbps) have another
102 * register for the short preamble ACK timeout calculation.
104 static inline void ath5k_hw_write_rate_duration(struct ath5k_hw *ah,
107 struct ath5k_softc *sc = ah->ah_sc;
108 struct ieee80211_rate *rate;
111 /* Write rate duration table */
112 for (i = 0; i < sc->sbands[IEEE80211_BAND_2GHZ].n_bitrates; i++) {
116 rate = &sc->sbands[IEEE80211_BAND_2GHZ].bitrates[control_rates[i]];
118 /* Set ACK timeout */
119 reg = AR5K_RATE_DUR(rate->hw_value);
121 /* An ACK frame consists of 10 bytes. If you add the FCS,
122 * which ieee80211_generic_frame_duration() adds,
123 * its 14 bytes. Note we use the control rate and not the
124 * actual rate for this rate. See mac80211 tx.c
125 * ieee80211_duration() for a brief description of
126 * what rate we should choose to TX ACKs. */
127 tx_time = le16_to_cpu(ieee80211_generic_frame_duration(sc->hw,
130 ath5k_hw_reg_write(ah, tx_time, reg);
132 if (!(rate->flags & IEEE80211_RATE_SHORT_PREAMBLE))
136 * We're not distinguishing short preamble here,
137 * This is true, all we'll get is a longer value here
138 * which is not necessarilly bad. We could use
139 * export ieee80211_frame_duration() but that needs to be
140 * fixed first to be properly used by mac802111 drivers:
142 * - remove erp stuff and let the routine figure ofdm
144 * - remove passing argument ieee80211_local as
145 * drivers don't have access to it
146 * - move drivers using ieee80211_generic_frame_duration()
149 ath5k_hw_reg_write(ah, tx_time,
150 reg + (AR5K_SET_SHORT_PREAMBLE << 2));
157 static int ath5k_hw_nic_reset(struct ath5k_hw *ah, u32 val)
160 u32 mask = val ? val : ~0U;
162 ATH5K_TRACE(ah->ah_sc);
164 /* Read-and-clear RX Descriptor Pointer*/
165 ath5k_hw_reg_read(ah, AR5K_RXDP);
168 * Reset the device and wait until success
170 ath5k_hw_reg_write(ah, val, AR5K_RESET_CTL);
172 /* Wait at least 128 PCI clocks */
175 if (ah->ah_version == AR5K_AR5210) {
176 val &= AR5K_RESET_CTL_CHIP;
177 mask &= AR5K_RESET_CTL_CHIP;
179 val &= AR5K_RESET_CTL_PCU | AR5K_RESET_CTL_BASEBAND;
180 mask &= AR5K_RESET_CTL_PCU | AR5K_RESET_CTL_BASEBAND;
183 ret = ath5k_hw_register_timeout(ah, AR5K_RESET_CTL, mask, val, false);
186 * Reset configuration register (for hw byte-swap). Note that this
187 * is only set for big endian. We do the necessary magic in
190 if ((val & AR5K_RESET_CTL_PCU) == 0)
191 ath5k_hw_reg_write(ah, AR5K_INIT_CFG, AR5K_CFG);
199 int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode,
200 bool set_chip, u16 sleep_duration)
205 ATH5K_TRACE(ah->ah_sc);
206 staid = ath5k_hw_reg_read(ah, AR5K_STA_ID1);
210 staid &= ~AR5K_STA_ID1_DEFAULT_ANTENNA;
212 case AR5K_PM_NETWORK_SLEEP:
214 ath5k_hw_reg_write(ah,
215 AR5K_SLEEP_CTL_SLE_ALLOW |
219 staid |= AR5K_STA_ID1_PWR_SV;
222 case AR5K_PM_FULL_SLEEP:
224 ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_SLP,
227 staid |= AR5K_STA_ID1_PWR_SV;
232 staid &= ~AR5K_STA_ID1_PWR_SV;
237 /* Preserve sleep duration */
238 data = ath5k_hw_reg_read(ah, AR5K_SLEEP_CTL);
239 if (data & 0xffc00000)
242 data = data & 0xfffcffff;
244 ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL);
247 for (i = 50; i > 0; i--) {
248 /* Check if the chip did wake up */
249 if ((ath5k_hw_reg_read(ah, AR5K_PCICFG) &
250 AR5K_PCICFG_SPWR_DN) == 0)
253 /* Wait a bit and retry */
255 ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL);
258 /* Fail if the chip didn't wake up */
269 ah->ah_power_mode = mode;
270 ath5k_hw_reg_write(ah, staid, AR5K_STA_ID1);
276 * Bring up MAC + PHY Chips
278 int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial)
280 struct pci_dev *pdev = ah->ah_sc->pdev;
281 u32 turbo, mode, clock, bus_flags;
288 ATH5K_TRACE(ah->ah_sc);
290 /* Wakeup the device */
291 ret = ath5k_hw_set_power(ah, AR5K_PM_AWAKE, true, 0);
293 ATH5K_ERR(ah->ah_sc, "failed to wakeup the MAC Chip\n");
297 if (ah->ah_version != AR5K_AR5210) {
299 * Get channel mode flags
302 if (ah->ah_radio >= AR5K_RF5112) {
303 mode = AR5K_PHY_MODE_RAD_RF5112;
304 clock = AR5K_PHY_PLL_RF5112;
306 mode = AR5K_PHY_MODE_RAD_RF5111; /*Zero*/
307 clock = AR5K_PHY_PLL_RF5111; /*Zero*/
310 if (flags & CHANNEL_2GHZ) {
311 mode |= AR5K_PHY_MODE_FREQ_2GHZ;
312 clock |= AR5K_PHY_PLL_44MHZ;
314 if (flags & CHANNEL_CCK) {
315 mode |= AR5K_PHY_MODE_MOD_CCK;
316 } else if (flags & CHANNEL_OFDM) {
317 /* XXX Dynamic OFDM/CCK is not supported by the
318 * AR5211 so we set MOD_OFDM for plain g (no
319 * CCK headers) operation. We need to test
320 * this, 5211 might support ofdm-only g after
321 * all, there are also initial register values
322 * in the code for g mode (see initvals.c). */
323 if (ah->ah_version == AR5K_AR5211)
324 mode |= AR5K_PHY_MODE_MOD_OFDM;
326 mode |= AR5K_PHY_MODE_MOD_DYN;
329 "invalid radio modulation mode\n");
332 } else if (flags & CHANNEL_5GHZ) {
333 mode |= AR5K_PHY_MODE_FREQ_5GHZ;
334 clock |= AR5K_PHY_PLL_40MHZ;
336 if (flags & CHANNEL_OFDM)
337 mode |= AR5K_PHY_MODE_MOD_OFDM;
340 "invalid radio modulation mode\n");
344 ATH5K_ERR(ah->ah_sc, "invalid radio frequency mode\n");
348 if (flags & CHANNEL_TURBO)
349 turbo = AR5K_PHY_TURBO_MODE | AR5K_PHY_TURBO_SHORT;
350 } else { /* Reset the device */
352 /* ...enable Atheros turbo mode if requested */
353 if (flags & CHANNEL_TURBO)
354 ath5k_hw_reg_write(ah, AR5K_PHY_TURBO_MODE,
358 /* reseting PCI on PCI-E cards results card to hang
359 * and always return 0xffff... so we ingore that flag
361 bus_flags = (pdev->is_pcie) ? 0 : AR5K_RESET_CTL_PCI;
364 ret = ath5k_hw_nic_reset(ah, AR5K_RESET_CTL_PCU |
365 AR5K_RESET_CTL_BASEBAND | bus_flags);
367 ATH5K_ERR(ah->ah_sc, "failed to reset the MAC Chip\n");
371 if (ah->ah_version == AR5K_AR5210)
374 /* ...wakeup again!*/
375 ret = ath5k_hw_set_power(ah, AR5K_PM_AWAKE, true, 0);
377 ATH5K_ERR(ah->ah_sc, "failed to resume the MAC Chip\n");
381 /* ...final warm reset */
382 if (ath5k_hw_nic_reset(ah, 0)) {
383 ATH5K_ERR(ah->ah_sc, "failed to warm reset the MAC Chip\n");
387 if (ah->ah_version != AR5K_AR5210) {
388 /* ...set the PHY operating mode */
389 ath5k_hw_reg_write(ah, clock, AR5K_PHY_PLL);
392 ath5k_hw_reg_write(ah, mode, AR5K_PHY_MODE);
393 ath5k_hw_reg_write(ah, turbo, AR5K_PHY_TURBO);
400 * Main reset function
402 int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
403 struct ieee80211_channel *channel, bool change_channel)
405 struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
406 struct pci_dev *pdev = ah->ah_sc->pdev;
407 u32 data, s_seq, s_ant, s_led[3], dma_size;
408 unsigned int i, mode, freq, ee_mode, ant[2];
411 ATH5K_TRACE(ah->ah_sc);
420 * Save some registers before a reset
422 /*DCU/Antenna selection not available on 5210*/
423 if (ah->ah_version != AR5K_AR5210) {
424 if (change_channel) {
425 /* Seq number for queue 0 -do this for all queues ? */
426 s_seq = ath5k_hw_reg_read(ah,
427 AR5K_QUEUE_DFS_SEQNUM(0));
429 s_ant = ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA);
434 s_led[0] = ath5k_hw_reg_read(ah, AR5K_PCICFG) & AR5K_PCICFG_LEDSTATE;
435 s_led[1] = ath5k_hw_reg_read(ah, AR5K_GPIOCR);
436 s_led[2] = ath5k_hw_reg_read(ah, AR5K_GPIODO);
438 if (change_channel && ah->ah_rf_banks != NULL)
439 ath5k_hw_get_rf_gain(ah);
442 /*Wakeup the device*/
443 ret = ath5k_hw_nic_wakeup(ah, channel->hw_value, false);
448 * Initialize operating mode
450 ah->ah_op_mode = op_mode;
454 * 5210 only comes with RF5110
456 if (ah->ah_version != AR5K_AR5210) {
457 if (ah->ah_radio != AR5K_RF5111 &&
458 ah->ah_radio != AR5K_RF5112 &&
459 ah->ah_radio != AR5K_RF5413 &&
460 ah->ah_radio != AR5K_RF2413 &&
461 ah->ah_radio != AR5K_RF2425) {
463 "invalid phy radio: %u\n", ah->ah_radio);
467 switch (channel->hw_value & CHANNEL_MODES) {
469 mode = AR5K_MODE_11A;
470 freq = AR5K_INI_RFGAIN_5GHZ;
471 ee_mode = AR5K_EEPROM_MODE_11A;
474 mode = AR5K_MODE_11G;
475 freq = AR5K_INI_RFGAIN_2GHZ;
476 ee_mode = AR5K_EEPROM_MODE_11G;
479 mode = AR5K_MODE_11B;
480 freq = AR5K_INI_RFGAIN_2GHZ;
481 ee_mode = AR5K_EEPROM_MODE_11B;
484 mode = AR5K_MODE_11A_TURBO;
485 freq = AR5K_INI_RFGAIN_5GHZ;
486 ee_mode = AR5K_EEPROM_MODE_11A;
488 /*Is this ok on 5211 too ?*/
490 mode = AR5K_MODE_11G_TURBO;
491 freq = AR5K_INI_RFGAIN_2GHZ;
492 ee_mode = AR5K_EEPROM_MODE_11G;
495 if (ah->ah_version == AR5K_AR5211) {
497 "XR mode not available on 5211");
501 freq = AR5K_INI_RFGAIN_5GHZ;
502 ee_mode = AR5K_EEPROM_MODE_11A;
506 "invalid channel: %d\n", channel->center_freq);
510 /* PHY access enable */
511 ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0));
515 ret = ath5k_hw_write_initvals(ah, mode, change_channel);
522 if (ah->ah_version != AR5K_AR5210) {
524 * Write initial RF gain settings
525 * This should work for both 5111/5112
527 ret = ath5k_hw_rfgain(ah, freq);
534 * Write some more initial register settings
536 if (ah->ah_version == AR5K_AR5212) {
537 ath5k_hw_reg_write(ah, 0x0002a002, 0x982c);
539 if (channel->hw_value == CHANNEL_G)
540 if (ah->ah_mac_srev < AR5K_SREV_VER_AR2413)
541 ath5k_hw_reg_write(ah, 0x00f80d80,
543 else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2424)
544 ath5k_hw_reg_write(ah, 0x00380140,
546 else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2425)
547 ath5k_hw_reg_write(ah, 0x00fc0ec0,
550 ath5k_hw_reg_write(ah, 0x00fc0fc0,
553 ath5k_hw_reg_write(ah, 0x00000000, 0x994c);
555 /* Some bits are disabled here, we know nothing about
556 * register 0xa228 yet, most of the times this ends up
557 * with a value 0x9b5 -haven't seen any dump with
558 * a different value- */
559 /* Got this from decompiling binary HAL */
560 data = ath5k_hw_reg_read(ah, 0xa228);
562 ath5k_hw_reg_write(ah, data, 0xa228);
564 data = ath5k_hw_reg_read(ah, 0xa228);
566 ath5k_hw_reg_write(ah, data, 0xa228);
569 /* Just write 0x9b5 ? */
570 /* ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); */
571 ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK);
572 ath5k_hw_reg_write(ah, 0x00000000, 0xa254);
573 ath5k_hw_reg_write(ah, 0x0000000e, AR5K_PHY_SCAL);
576 /* Fix for first revision of the RF5112 RF chipset */
577 if (ah->ah_radio >= AR5K_RF5112 &&
578 ah->ah_radio_5ghz_revision <
579 AR5K_SREV_RAD_5112A) {
580 ath5k_hw_reg_write(ah, AR5K_PHY_CCKTXCTL_WORLD,
582 if (channel->hw_value & CHANNEL_5GHZ)
586 ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL);
591 * Set TX power (FIXME)
593 ret = ath5k_hw_txpower(ah, channel, AR5K_TUNE_DEFAULT_TXPOWER);
597 /* Write rate duration table only on AR5212 and if
598 * virtual interface has already been brought up
599 * XXX: rethink this after new mode changes to
600 * mac80211 are integrated */
601 if (ah->ah_version == AR5K_AR5212 &&
602 ah->ah_sc->vif != NULL)
603 ath5k_hw_write_rate_duration(ah, mode);
608 ret = ath5k_hw_rfregs(ah, channel, mode);
613 * Configure additional registers
616 /* Write OFDM timings on 5212*/
617 if (ah->ah_version == AR5K_AR5212 &&
618 channel->hw_value & CHANNEL_OFDM) {
619 ret = ath5k_hw_write_ofdm_timings(ah, channel);
624 /*Enable/disable 802.11b mode on 5111
625 (enable 2111 frequency converter + CCK)*/
626 if (ah->ah_radio == AR5K_RF5111) {
627 if (mode == AR5K_MODE_11B)
628 AR5K_REG_ENABLE_BITS(ah, AR5K_TXCFG,
631 AR5K_REG_DISABLE_BITS(ah, AR5K_TXCFG,
636 * Set channel and calibrate the PHY
638 ret = ath5k_hw_channel(ah, channel);
642 /* Set antenna mode */
643 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_ANT_CTL,
644 ah->ah_antenna[ee_mode][0], 0xfffffc06);
647 * In case a fixed antenna was set as default
648 * write the same settings on both AR5K_PHY_ANT_SWITCH_TABLE
652 if (s_ant == AR5K_ANT_FIXED_A) /* 1 - Main */
653 ant[0] = ant[1] = AR5K_ANT_FIXED_A;
655 ant[0] = ant[1] = AR5K_ANT_FIXED_B;
657 ant[0] = AR5K_ANT_FIXED_A;
658 ant[1] = AR5K_ANT_FIXED_B;
661 ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[0]],
662 AR5K_PHY_ANT_SWITCH_TABLE_0);
663 ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[1]],
664 AR5K_PHY_ANT_SWITCH_TABLE_1);
666 /* Commit values from EEPROM */
667 if (ah->ah_radio == AR5K_RF5111)
668 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL,
669 AR5K_PHY_FRAME_CTL_TX_CLIP, ee->ee_tx_clip);
671 ath5k_hw_reg_write(ah,
672 AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]),
675 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_SETTLING,
676 (ee->ee_switch_settling[ee_mode] << 7) & 0x3f80,
678 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_GAIN,
679 (ee->ee_ant_tx_rx[ee_mode] << 12) & 0x3f000,
681 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_DESIRED_SIZE,
682 (ee->ee_adc_desired_size[ee_mode] & 0x00ff) |
683 ((ee->ee_pga_desired_size[ee_mode] << 8) & 0xff00),
686 ath5k_hw_reg_write(ah,
687 (ee->ee_tx_end2xpa_disable[ee_mode] << 24) |
688 (ee->ee_tx_end2xpa_disable[ee_mode] << 16) |
689 (ee->ee_tx_frm2xpa_enable[ee_mode] << 8) |
690 (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4);
692 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_RF_CTL3,
693 ee->ee_tx_end2xlna_enable[ee_mode] << 8, 0xffff00ff);
694 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_NF,
695 (ee->ee_thr_62[ee_mode] << 12) & 0x7f000, 0xfff80fff);
696 AR5K_REG_MASKED_BITS(ah, AR5K_PHY_OFDM_SELFCORR, 4, 0xffffff01);
698 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
699 AR5K_PHY_IQ_CORR_ENABLE |
700 (ee->ee_i_cal[ee_mode] << AR5K_PHY_IQ_CORR_Q_I_COFF_S) |
701 ee->ee_q_cal[ee_mode]);
703 if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_4_1)
704 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN_2GHZ,
705 AR5K_PHY_GAIN_2GHZ_MARGIN_TXRX,
706 ee->ee_margin_tx_rx[ee_mode]);
710 /* Disable phy and wait */
711 ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT);
716 * Restore saved values
718 /*DCU/Antenna selection not available on 5210*/
719 if (ah->ah_version != AR5K_AR5210) {
720 ath5k_hw_reg_write(ah, s_seq, AR5K_QUEUE_DFS_SEQNUM(0));
721 ath5k_hw_reg_write(ah, s_ant, AR5K_DEFAULT_ANTENNA);
723 AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, s_led[0]);
724 ath5k_hw_reg_write(ah, s_led[1], AR5K_GPIOCR);
725 ath5k_hw_reg_write(ah, s_led[2], AR5K_GPIODO);
730 /* XXX: add ah->aid once mac80211 gives this to us */
731 ath5k_hw_set_associd(ah, ah->ah_bssid, 0);
733 ath5k_hw_set_opmode(ah);
734 /*PISR/SISR Not available on 5210*/
735 if (ah->ah_version != AR5K_AR5210) {
736 ath5k_hw_reg_write(ah, 0xffffffff, AR5K_PISR);
737 /* If we later allow tuning for this, store into sc structure */
738 data = AR5K_TUNE_RSSI_THRES |
739 AR5K_TUNE_BMISS_THRES << AR5K_RSSI_THR_BMISS_S;
740 ath5k_hw_reg_write(ah, data, AR5K_RSSI_THR);
744 * Set Rx/Tx DMA Configuration
746 * Set maximum DMA size (512) except for PCI-E cards since
747 * it causes rx overruns and tx errors (tested on 5424 but since
748 * rx overruns also occur on 5416/5418 with madwifi we set 128
749 * for all PCI-E cards to be safe).
751 * In dumps this is 128 for allchips.
753 * XXX: need to check 5210 for this
754 * TODO: Check out tx triger level, it's always 64 on dumps but I
755 * guess we can tweak it and see how it goes ;-)
757 dma_size = (pdev->is_pcie) ? AR5K_DMASIZE_128B : AR5K_DMASIZE_512B;
758 if (ah->ah_version != AR5K_AR5210) {
759 AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG,
760 AR5K_TXCFG_SDMAMR, dma_size);
761 AR5K_REG_WRITE_BITS(ah, AR5K_RXCFG,
762 AR5K_RXCFG_SDMAMW, dma_size);
766 * Enable the PHY and wait until completion
768 ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT);
771 * On 5211+ read activation -> rx delay
774 if (ah->ah_version != AR5K_AR5210) {
775 data = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
777 data = (channel->hw_value & CHANNEL_CCK) ?
778 ((data << 2) / 22) : (data / 10);
780 udelay(100 + (2 * data));
787 * Perform ADC test (?)
789 data = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
790 ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
791 for (i = 0; i <= 20; i++) {
792 if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
796 ath5k_hw_reg_write(ah, data, AR5K_PHY_TST1);
800 * Start automatic gain calibration
802 * During AGC calibration RX path is re-routed to
803 * a signal detector so we don't receive anything.
805 * This method is used to calibrate some static offsets
806 * used together with on-the fly I/Q calibration (the
807 * one performed via ath5k_hw_phy_calibrate), that doesn't
810 * If we are in a noisy environment AGC calibration may time
813 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
814 AR5K_PHY_AGCCTL_CAL);
816 /* At the same time start I/Q calibration for QAM constellation
817 * -no need for CCK- */
818 ah->ah_calibration = false;
819 if (!(mode == AR5K_MODE_11B)) {
820 ah->ah_calibration = true;
821 AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
822 AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
823 AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
827 /* Wait for gain calibration to finish (we check for I/Q calibration
828 * during ath5k_phy_calibrate) */
829 if (ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
830 AR5K_PHY_AGCCTL_CAL, 0, false)) {
831 ATH5K_ERR(ah->ah_sc, "gain calibration timeout (%uMHz)\n",
832 channel->center_freq);
837 * Start noise floor calibration
839 * If we run NF calibration before AGC, it always times out.
840 * Binary HAL starts NF and AGC calibration at the same time
841 * and only waits for AGC to finish. I believe that's wrong because
842 * during NF calibration, rx path is also routed to a detector, so if
843 * it doesn't finish we won't have RX.
845 * XXX: Find an interval that's OK for all cards...
847 ret = ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
852 * Reset queues and start beacon timers at the end of the reset routine
854 for (i = 0; i < ah->ah_capabilities.cap_queues.q_tx_num; i++) {
856 if (ah->ah_version != AR5K_AR5210)
857 AR5K_REG_WRITE_Q(ah, AR5K_QUEUE_QCUMASK(i), i);
859 ret = ath5k_hw_reset_tx_queue(ah, i);
862 "failed to reset TX queue #%d\n", i);
867 /* Pre-enable interrupts on 5211/5212*/
868 if (ah->ah_version != AR5K_AR5210)
869 ath5k_hw_set_imr(ah, AR5K_INT_RX | AR5K_INT_TX |
873 * Set RF kill flags if supported by the device (read from the EEPROM)
874 * Disable gpio_intr for now since it results system hang.
875 * TODO: Handle this in ath5k_intr
878 if (AR5K_EEPROM_HDR_RFKILL(ah->ah_capabilities.cap_eeprom.ee_header)) {
879 ath5k_hw_set_gpio_input(ah, 0);
880 ah->ah_gpio[0] = ath5k_hw_get_gpio(ah, 0);
881 if (ah->ah_gpio[0] == 0)
882 ath5k_hw_set_gpio_intr(ah, 0, 1);
884 ath5k_hw_set_gpio_intr(ah, 0, 0);
889 * Set the 32MHz reference clock on 5212 phy clock sleep register
891 * TODO: Find out how to switch to external 32Khz clock to save power
893 if (ah->ah_version == AR5K_AR5212) {
894 ath5k_hw_reg_write(ah, AR5K_PHY_SCR_32MHZ, AR5K_PHY_SCR);
895 ath5k_hw_reg_write(ah, AR5K_PHY_SLMT_32MHZ, AR5K_PHY_SLMT);
896 ath5k_hw_reg_write(ah, AR5K_PHY_SCAL_32MHZ, AR5K_PHY_SCAL);
897 ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK);
898 ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY);
899 ath5k_hw_reg_write(ah, ah->ah_phy_spending, AR5K_PHY_SPENDING);
901 data = ath5k_hw_reg_read(ah, AR5K_USEC_5211) & 0xffffc07f ;
902 data |= (ah->ah_phy_spending == AR5K_PHY_SPENDING_18) ?
903 0x00000f80 : 0x00001380 ;
904 ath5k_hw_reg_write(ah, data, AR5K_USEC_5211);
908 if (ah->ah_version == AR5K_AR5212) {
909 ath5k_hw_reg_write(ah, 0x000100aa, 0x8118);
910 ath5k_hw_reg_write(ah, 0x00003210, 0x811c);
911 ath5k_hw_reg_write(ah, 0x00000052, 0x8108);
912 if (ah->ah_mac_srev >= AR5K_SREV_VER_AR2413)
913 ath5k_hw_reg_write(ah, 0x00000004, 0x8120);
917 * Disable beacons and reset the register
919 AR5K_REG_DISABLE_BITS(ah, AR5K_BEACON, AR5K_BEACON_ENABLE |
920 AR5K_BEACON_RESET_TSF);