1 /******************************************************************************
3 * Copyright(c) 2003 - 2008 Intel Corporation. All rights reserved.
5 * Portions of this file are derived from the ipw3945 project, as well
6 * as portions of the ieee80211 subsystem header files.
8 * This program is free software; you can redistribute it and/or modify it
9 * under the terms of version 2 of the GNU General Public License as
10 * published by the Free Software Foundation.
12 * This program is distributed in the hope that it will be useful, but WITHOUT
13 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
14 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
17 * You should have received a copy of the GNU General Public License along with
18 * this program; if not, write to the Free Software Foundation, Inc.,
19 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
21 * The full GNU General Public License is included in this distribution in the
22 * file called LICENSE.
24 * Contact Information:
25 * James P. Ketrenos <ipw2100-admin@linux.intel.com>
26 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
28 *****************************************************************************/
30 #include <linux/kernel.h>
31 #include <linux/module.h>
32 #include <linux/init.h>
33 #include <linux/pci.h>
34 #include <linux/dma-mapping.h>
35 #include <linux/delay.h>
36 #include <linux/skbuff.h>
37 #include <linux/netdevice.h>
38 #include <linux/wireless.h>
39 #include <linux/firmware.h>
40 #include <linux/etherdevice.h>
41 #include <linux/if_arp.h>
43 #include <net/ieee80211_radiotap.h>
44 #include <net/mac80211.h>
46 #include <asm/div64.h>
48 #include "iwl-3945-core.h"
50 #include "iwl-helpers.h"
52 #ifdef CONFIG_IWL3945_DEBUG
53 u32 iwl3945_debug_level;
56 static int iwl3945_tx_queue_update_write_ptr(struct iwl3945_priv *priv,
57 struct iwl3945_tx_queue *txq);
59 /******************************************************************************
63 ******************************************************************************/
65 /* module parameters */
66 static int iwl3945_param_disable_hw_scan; /* def: 0 = use 3945's h/w scan */
67 static int iwl3945_param_debug; /* def: 0 = minimal debug log messages */
68 static int iwl3945_param_disable; /* def: 0 = enable radio */
69 static int iwl3945_param_antenna; /* def: 0 = both antennas (use diversity) */
70 int iwl3945_param_hwcrypto; /* def: 0 = use software encryption */
71 static int iwl3945_param_qos_enable = 1; /* def: 1 = use quality of service */
72 int iwl3945_param_queues_num = IWL39_MAX_NUM_QUEUES; /* def: 8 Tx queues */
75 * module name, copyright, version, etc.
76 * NOTE: DRV_NAME is defined in iwlwifi.h for use by iwl-debug.h and printk
79 #define DRV_DESCRIPTION \
80 "Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux"
82 #ifdef CONFIG_IWL3945_DEBUG
88 #ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT
94 #define IWLWIFI_VERSION "1.2.26k" VD VS
95 #define DRV_COPYRIGHT "Copyright(c) 2003-2008 Intel Corporation"
96 #define DRV_VERSION IWLWIFI_VERSION
99 MODULE_DESCRIPTION(DRV_DESCRIPTION);
100 MODULE_VERSION(DRV_VERSION);
101 MODULE_AUTHOR(DRV_COPYRIGHT);
102 MODULE_LICENSE("GPL");
104 static const struct ieee80211_supported_band *iwl3945_get_band(
105 struct iwl3945_priv *priv, enum ieee80211_band band)
107 return priv->hw->wiphy->bands[band];
110 static int iwl3945_is_empty_essid(const char *essid, int essid_len)
112 /* Single white space is for Linksys APs */
113 if (essid_len == 1 && essid[0] == ' ')
116 /* Otherwise, if the entire essid is 0, we assume it is hidden */
119 if (essid[essid_len] != '\0')
126 static const char *iwl3945_escape_essid(const char *essid, u8 essid_len)
128 static char escaped[IW_ESSID_MAX_SIZE * 2 + 1];
129 const char *s = essid;
132 if (iwl3945_is_empty_essid(essid, essid_len)) {
133 memcpy(escaped, "<hidden>", sizeof("<hidden>"));
137 essid_len = min(essid_len, (u8) IW_ESSID_MAX_SIZE);
138 while (essid_len--) {
150 /*************** DMA-QUEUE-GENERAL-FUNCTIONS *****
153 * Theory of operation
155 * A Tx or Rx queue resides in host DRAM, and is comprised of a circular buffer
156 * of buffer descriptors, each of which points to one or more data buffers for
157 * the device to read from or fill. Driver and device exchange status of each
158 * queue via "read" and "write" pointers. Driver keeps minimum of 2 empty
159 * entries in each circular buffer, to protect against confusing empty and full
162 * The device reads or writes the data in the queues via the device's several
163 * DMA/FIFO channels. Each queue is mapped to a single DMA channel.
165 * For Tx queue, there are low mark and high mark limits. If, after queuing
166 * the packet for Tx, free space become < low mark, Tx queue stopped. When
167 * reclaiming packets (on 'tx done IRQ), if free space become > high mark,
170 * The 3945 operates with six queues: One receive queue, one transmit queue
171 * (#4) for sending commands to the device firmware, and four transmit queues
172 * (#0-3) for data tx via EDCA. An additional 2 HCCA queues are unused.
173 ***************************************************/
175 int iwl3945_queue_space(const struct iwl3945_queue *q)
177 int s = q->read_ptr - q->write_ptr;
179 if (q->read_ptr > q->write_ptr)
184 /* keep some reserve to not confuse empty and full situations */
191 int iwl3945_x2_queue_used(const struct iwl3945_queue *q, int i)
193 return q->write_ptr > q->read_ptr ?
194 (i >= q->read_ptr && i < q->write_ptr) :
195 !(i < q->read_ptr && i >= q->write_ptr);
199 static inline u8 get_cmd_index(struct iwl3945_queue *q, u32 index, int is_huge)
201 /* This is for scan command, the big buffer at end of command array */
203 return q->n_window; /* must be power of 2 */
205 /* Otherwise, use normal size buffers */
206 return index & (q->n_window - 1);
210 * iwl3945_queue_init - Initialize queue's high/low-water and read/write indexes
212 static int iwl3945_queue_init(struct iwl3945_priv *priv, struct iwl3945_queue *q,
213 int count, int slots_num, u32 id)
216 q->n_window = slots_num;
219 /* count must be power-of-two size, otherwise iwl_queue_inc_wrap
220 * and iwl_queue_dec_wrap are broken. */
221 BUG_ON(!is_power_of_2(count));
223 /* slots_num must be power-of-two size, otherwise
224 * get_cmd_index is broken. */
225 BUG_ON(!is_power_of_2(slots_num));
227 q->low_mark = q->n_window / 4;
231 q->high_mark = q->n_window / 8;
232 if (q->high_mark < 2)
235 q->write_ptr = q->read_ptr = 0;
241 * iwl3945_tx_queue_alloc - Alloc driver data and TFD CB for one Tx/cmd queue
243 static int iwl3945_tx_queue_alloc(struct iwl3945_priv *priv,
244 struct iwl3945_tx_queue *txq, u32 id)
246 struct pci_dev *dev = priv->pci_dev;
248 /* Driver private data, only for Tx (not command) queues,
249 * not shared with device. */
250 if (id != IWL_CMD_QUEUE_NUM) {
251 txq->txb = kmalloc(sizeof(txq->txb[0]) *
252 TFD_QUEUE_SIZE_MAX, GFP_KERNEL);
254 IWL_ERROR("kmalloc for auxiliary BD "
255 "structures failed\n");
261 /* Circular buffer of transmit frame descriptors (TFDs),
262 * shared with device */
263 txq->bd = pci_alloc_consistent(dev,
264 sizeof(txq->bd[0]) * TFD_QUEUE_SIZE_MAX,
268 IWL_ERROR("pci_alloc_consistent(%zd) failed\n",
269 sizeof(txq->bd[0]) * TFD_QUEUE_SIZE_MAX);
284 * iwl3945_tx_queue_init - Allocate and initialize one tx/cmd queue
286 int iwl3945_tx_queue_init(struct iwl3945_priv *priv,
287 struct iwl3945_tx_queue *txq, int slots_num, u32 txq_id)
289 struct pci_dev *dev = priv->pci_dev;
294 * Alloc buffer array for commands (Tx or other types of commands).
295 * For the command queue (#4), allocate command space + one big
296 * command for scan, since scan command is very huge; the system will
297 * not have two scans at the same time, so only one is needed.
298 * For data Tx queues (all other queues), no super-size command
301 len = sizeof(struct iwl3945_cmd) * slots_num;
302 if (txq_id == IWL_CMD_QUEUE_NUM)
303 len += IWL_MAX_SCAN_SIZE;
304 txq->cmd = pci_alloc_consistent(dev, len, &txq->dma_addr_cmd);
308 /* Alloc driver data array and TFD circular buffer */
309 rc = iwl3945_tx_queue_alloc(priv, txq, txq_id);
311 pci_free_consistent(dev, len, txq->cmd, txq->dma_addr_cmd);
315 txq->need_update = 0;
317 /* TFD_QUEUE_SIZE_MAX must be power-of-two size, otherwise
318 * iwl_queue_inc_wrap and iwl_queue_dec_wrap are broken. */
319 BUILD_BUG_ON(TFD_QUEUE_SIZE_MAX & (TFD_QUEUE_SIZE_MAX - 1));
321 /* Initialize queue high/low-water, head/tail indexes */
322 iwl3945_queue_init(priv, &txq->q, TFD_QUEUE_SIZE_MAX, slots_num, txq_id);
324 /* Tell device where to find queue, enable DMA channel. */
325 iwl3945_hw_tx_queue_init(priv, txq);
331 * iwl3945_tx_queue_free - Deallocate DMA queue.
332 * @txq: Transmit queue to deallocate.
334 * Empty queue by removing and destroying all BD's.
336 * 0-fill, but do not free "txq" descriptor structure.
338 void iwl3945_tx_queue_free(struct iwl3945_priv *priv, struct iwl3945_tx_queue *txq)
340 struct iwl3945_queue *q = &txq->q;
341 struct pci_dev *dev = priv->pci_dev;
347 /* first, empty all BD's */
348 for (; q->write_ptr != q->read_ptr;
349 q->read_ptr = iwl_queue_inc_wrap(q->read_ptr, q->n_bd))
350 iwl3945_hw_txq_free_tfd(priv, txq);
352 len = sizeof(struct iwl3945_cmd) * q->n_window;
353 if (q->id == IWL_CMD_QUEUE_NUM)
354 len += IWL_MAX_SCAN_SIZE;
356 /* De-alloc array of command/tx buffers */
357 pci_free_consistent(dev, len, txq->cmd, txq->dma_addr_cmd);
359 /* De-alloc circular buffer of TFDs */
361 pci_free_consistent(dev, sizeof(struct iwl3945_tfd_frame) *
362 txq->q.n_bd, txq->bd, txq->q.dma_addr);
364 /* De-alloc array of per-TFD driver data */
368 /* 0-fill queue descriptor structure */
369 memset(txq, 0, sizeof(*txq));
372 const u8 iwl3945_broadcast_addr[ETH_ALEN] = { 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF };
374 /*************** STATION TABLE MANAGEMENT ****
375 * mac80211 should be examined to determine if sta_info is duplicating
376 * the functionality provided here
379 /**************************************************************/
380 #if 0 /* temporary disable till we add real remove station */
382 * iwl3945_remove_station - Remove driver's knowledge of station.
384 * NOTE: This does not remove station from device's station table.
386 static u8 iwl3945_remove_station(struct iwl3945_priv *priv, const u8 *addr, int is_ap)
388 int index = IWL_INVALID_STATION;
392 spin_lock_irqsave(&priv->sta_lock, flags);
396 else if (is_broadcast_ether_addr(addr))
397 index = priv->hw_setting.bcast_sta_id;
399 for (i = IWL_STA_ID; i < priv->hw_setting.max_stations; i++)
400 if (priv->stations[i].used &&
401 !compare_ether_addr(priv->stations[i].sta.sta.addr,
407 if (unlikely(index == IWL_INVALID_STATION))
410 if (priv->stations[index].used) {
411 priv->stations[index].used = 0;
412 priv->num_stations--;
415 BUG_ON(priv->num_stations < 0);
418 spin_unlock_irqrestore(&priv->sta_lock, flags);
424 * iwl3945_clear_stations_table - Clear the driver's station table
426 * NOTE: This does not clear or otherwise alter the device's station table.
428 static void iwl3945_clear_stations_table(struct iwl3945_priv *priv)
432 spin_lock_irqsave(&priv->sta_lock, flags);
434 priv->num_stations = 0;
435 memset(priv->stations, 0, sizeof(priv->stations));
437 spin_unlock_irqrestore(&priv->sta_lock, flags);
441 * iwl3945_add_station - Add station to station tables in driver and device
443 u8 iwl3945_add_station(struct iwl3945_priv *priv, const u8 *addr, int is_ap, u8 flags)
446 int index = IWL_INVALID_STATION;
447 struct iwl3945_station_entry *station;
448 unsigned long flags_spin;
449 DECLARE_MAC_BUF(mac);
452 spin_lock_irqsave(&priv->sta_lock, flags_spin);
455 else if (is_broadcast_ether_addr(addr))
456 index = priv->hw_setting.bcast_sta_id;
458 for (i = IWL_STA_ID; i < priv->hw_setting.max_stations; i++) {
459 if (!compare_ether_addr(priv->stations[i].sta.sta.addr,
465 if (!priv->stations[i].used &&
466 index == IWL_INVALID_STATION)
470 /* These two conditions has the same outcome but keep them separate
471 since they have different meaning */
472 if (unlikely(index == IWL_INVALID_STATION)) {
473 spin_unlock_irqrestore(&priv->sta_lock, flags_spin);
477 if (priv->stations[index].used &&
478 !compare_ether_addr(priv->stations[index].sta.sta.addr, addr)) {
479 spin_unlock_irqrestore(&priv->sta_lock, flags_spin);
483 IWL_DEBUG_ASSOC("Add STA ID %d: %s\n", index, print_mac(mac, addr));
484 station = &priv->stations[index];
486 priv->num_stations++;
488 /* Set up the REPLY_ADD_STA command to send to device */
489 memset(&station->sta, 0, sizeof(struct iwl3945_addsta_cmd));
490 memcpy(station->sta.sta.addr, addr, ETH_ALEN);
491 station->sta.mode = 0;
492 station->sta.sta.sta_id = index;
493 station->sta.station_flags = 0;
495 if (priv->band == IEEE80211_BAND_5GHZ)
496 rate = IWL_RATE_6M_PLCP;
498 rate = IWL_RATE_1M_PLCP;
500 /* Turn on both antennas for the station... */
501 station->sta.rate_n_flags =
502 iwl3945_hw_set_rate_n_flags(rate, RATE_MCS_ANT_AB_MSK);
503 station->current_rate.rate_n_flags =
504 le16_to_cpu(station->sta.rate_n_flags);
506 spin_unlock_irqrestore(&priv->sta_lock, flags_spin);
508 /* Add station to device's station table */
509 iwl3945_send_add_station(priv, &station->sta, flags);
514 /*************** DRIVER STATUS FUNCTIONS *****/
516 static inline int iwl3945_is_ready(struct iwl3945_priv *priv)
518 /* The adapter is 'ready' if READY and GEO_CONFIGURED bits are
519 * set but EXIT_PENDING is not */
520 return test_bit(STATUS_READY, &priv->status) &&
521 test_bit(STATUS_GEO_CONFIGURED, &priv->status) &&
522 !test_bit(STATUS_EXIT_PENDING, &priv->status);
525 static inline int iwl3945_is_alive(struct iwl3945_priv *priv)
527 return test_bit(STATUS_ALIVE, &priv->status);
530 static inline int iwl3945_is_init(struct iwl3945_priv *priv)
532 return test_bit(STATUS_INIT, &priv->status);
535 static inline int iwl3945_is_rfkill_sw(struct iwl3945_priv *priv)
537 return test_bit(STATUS_RF_KILL_SW, &priv->status);
540 static inline int iwl3945_is_rfkill_hw(struct iwl3945_priv *priv)
542 return test_bit(STATUS_RF_KILL_HW, &priv->status);
545 static inline int iwl3945_is_rfkill(struct iwl3945_priv *priv)
547 return iwl3945_is_rfkill_hw(priv) ||
548 iwl3945_is_rfkill_sw(priv);
551 static inline int iwl3945_is_ready_rf(struct iwl3945_priv *priv)
554 if (iwl3945_is_rfkill(priv))
557 return iwl3945_is_ready(priv);
560 /*************** HOST COMMAND QUEUE FUNCTIONS *****/
562 #define IWL_CMD(x) case x : return #x
564 static const char *get_cmd_string(u8 cmd)
567 IWL_CMD(REPLY_ALIVE);
568 IWL_CMD(REPLY_ERROR);
570 IWL_CMD(REPLY_RXON_ASSOC);
571 IWL_CMD(REPLY_QOS_PARAM);
572 IWL_CMD(REPLY_RXON_TIMING);
573 IWL_CMD(REPLY_ADD_STA);
574 IWL_CMD(REPLY_REMOVE_STA);
575 IWL_CMD(REPLY_REMOVE_ALL_STA);
576 IWL_CMD(REPLY_3945_RX);
578 IWL_CMD(REPLY_RATE_SCALE);
579 IWL_CMD(REPLY_LEDS_CMD);
580 IWL_CMD(REPLY_TX_LINK_QUALITY_CMD);
581 IWL_CMD(RADAR_NOTIFICATION);
582 IWL_CMD(REPLY_QUIET_CMD);
583 IWL_CMD(REPLY_CHANNEL_SWITCH);
584 IWL_CMD(CHANNEL_SWITCH_NOTIFICATION);
585 IWL_CMD(REPLY_SPECTRUM_MEASUREMENT_CMD);
586 IWL_CMD(SPECTRUM_MEASURE_NOTIFICATION);
587 IWL_CMD(POWER_TABLE_CMD);
588 IWL_CMD(PM_SLEEP_NOTIFICATION);
589 IWL_CMD(PM_DEBUG_STATISTIC_NOTIFIC);
590 IWL_CMD(REPLY_SCAN_CMD);
591 IWL_CMD(REPLY_SCAN_ABORT_CMD);
592 IWL_CMD(SCAN_START_NOTIFICATION);
593 IWL_CMD(SCAN_RESULTS_NOTIFICATION);
594 IWL_CMD(SCAN_COMPLETE_NOTIFICATION);
595 IWL_CMD(BEACON_NOTIFICATION);
596 IWL_CMD(REPLY_TX_BEACON);
597 IWL_CMD(WHO_IS_AWAKE_NOTIFICATION);
598 IWL_CMD(QUIET_NOTIFICATION);
599 IWL_CMD(REPLY_TX_PWR_TABLE_CMD);
600 IWL_CMD(MEASURE_ABORT_NOTIFICATION);
601 IWL_CMD(REPLY_BT_CONFIG);
602 IWL_CMD(REPLY_STATISTICS_CMD);
603 IWL_CMD(STATISTICS_NOTIFICATION);
604 IWL_CMD(REPLY_CARD_STATE_CMD);
605 IWL_CMD(CARD_STATE_NOTIFICATION);
606 IWL_CMD(MISSED_BEACONS_NOTIFICATION);
613 #define HOST_COMPLETE_TIMEOUT (HZ / 2)
616 * iwl3945_enqueue_hcmd - enqueue a uCode command
617 * @priv: device private data point
618 * @cmd: a point to the ucode command structure
620 * The function returns < 0 values to indicate the operation is
621 * failed. On success, it turns the index (> 0) of command in the
624 static int iwl3945_enqueue_hcmd(struct iwl3945_priv *priv, struct iwl3945_host_cmd *cmd)
626 struct iwl3945_tx_queue *txq = &priv->txq[IWL_CMD_QUEUE_NUM];
627 struct iwl3945_queue *q = &txq->q;
628 struct iwl3945_tfd_frame *tfd;
630 struct iwl3945_cmd *out_cmd;
632 u16 fix_size = (u16)(cmd->len + sizeof(out_cmd->hdr));
633 dma_addr_t phys_addr;
639 /* If any of the command structures end up being larger than
640 * the TFD_MAX_PAYLOAD_SIZE, and it sent as a 'small' command then
641 * we will need to increase the size of the TFD entries */
642 BUG_ON((fix_size > TFD_MAX_PAYLOAD_SIZE) &&
643 !(cmd->meta.flags & CMD_SIZE_HUGE));
646 if (iwl3945_is_rfkill(priv)) {
647 IWL_DEBUG_INFO("Not sending command - RF KILL");
651 if (iwl3945_queue_space(q) < ((cmd->meta.flags & CMD_ASYNC) ? 2 : 1)) {
652 IWL_ERROR("No space for Tx\n");
656 spin_lock_irqsave(&priv->hcmd_lock, flags);
658 tfd = &txq->bd[q->write_ptr];
659 memset(tfd, 0, sizeof(*tfd));
661 control_flags = (u32 *) tfd;
663 idx = get_cmd_index(q, q->write_ptr, cmd->meta.flags & CMD_SIZE_HUGE);
664 out_cmd = &txq->cmd[idx];
666 out_cmd->hdr.cmd = cmd->id;
667 memcpy(&out_cmd->meta, &cmd->meta, sizeof(cmd->meta));
668 memcpy(&out_cmd->cmd.payload, cmd->data, cmd->len);
670 /* At this point, the out_cmd now has all of the incoming cmd
673 out_cmd->hdr.flags = 0;
674 out_cmd->hdr.sequence = cpu_to_le16(QUEUE_TO_SEQ(IWL_CMD_QUEUE_NUM) |
675 INDEX_TO_SEQ(q->write_ptr));
676 if (out_cmd->meta.flags & CMD_SIZE_HUGE)
677 out_cmd->hdr.sequence |= cpu_to_le16(SEQ_HUGE_FRAME);
679 phys_addr = txq->dma_addr_cmd + sizeof(txq->cmd[0]) * idx +
680 offsetof(struct iwl3945_cmd, hdr);
681 iwl3945_hw_txq_attach_buf_to_tfd(priv, tfd, phys_addr, fix_size);
683 pad = U32_PAD(cmd->len);
684 count = TFD_CTL_COUNT_GET(*control_flags);
685 *control_flags = TFD_CTL_COUNT_SET(count) | TFD_CTL_PAD_SET(pad);
687 IWL_DEBUG_HC("Sending command %s (#%x), seq: 0x%04X, "
688 "%d bytes at %d[%d]:%d\n",
689 get_cmd_string(out_cmd->hdr.cmd),
690 out_cmd->hdr.cmd, le16_to_cpu(out_cmd->hdr.sequence),
691 fix_size, q->write_ptr, idx, IWL_CMD_QUEUE_NUM);
693 txq->need_update = 1;
695 /* Increment and update queue's write index */
696 q->write_ptr = iwl_queue_inc_wrap(q->write_ptr, q->n_bd);
697 ret = iwl3945_tx_queue_update_write_ptr(priv, txq);
699 spin_unlock_irqrestore(&priv->hcmd_lock, flags);
700 return ret ? ret : idx;
703 static int iwl3945_send_cmd_async(struct iwl3945_priv *priv, struct iwl3945_host_cmd *cmd)
707 BUG_ON(!(cmd->meta.flags & CMD_ASYNC));
709 /* An asynchronous command can not expect an SKB to be set. */
710 BUG_ON(cmd->meta.flags & CMD_WANT_SKB);
712 /* An asynchronous command MUST have a callback. */
713 BUG_ON(!cmd->meta.u.callback);
715 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
718 ret = iwl3945_enqueue_hcmd(priv, cmd);
720 IWL_ERROR("Error sending %s: iwl3945_enqueue_hcmd failed: %d\n",
721 get_cmd_string(cmd->id), ret);
727 static int iwl3945_send_cmd_sync(struct iwl3945_priv *priv, struct iwl3945_host_cmd *cmd)
732 BUG_ON(cmd->meta.flags & CMD_ASYNC);
734 /* A synchronous command can not have a callback set. */
735 BUG_ON(cmd->meta.u.callback != NULL);
737 if (test_and_set_bit(STATUS_HCMD_SYNC_ACTIVE, &priv->status)) {
738 IWL_ERROR("Error sending %s: Already sending a host command\n",
739 get_cmd_string(cmd->id));
744 set_bit(STATUS_HCMD_ACTIVE, &priv->status);
746 if (cmd->meta.flags & CMD_WANT_SKB)
747 cmd->meta.source = &cmd->meta;
749 cmd_idx = iwl3945_enqueue_hcmd(priv, cmd);
752 IWL_ERROR("Error sending %s: iwl3945_enqueue_hcmd failed: %d\n",
753 get_cmd_string(cmd->id), ret);
757 ret = wait_event_interruptible_timeout(priv->wait_command_queue,
758 !test_bit(STATUS_HCMD_ACTIVE, &priv->status),
759 HOST_COMPLETE_TIMEOUT);
761 if (test_bit(STATUS_HCMD_ACTIVE, &priv->status)) {
762 IWL_ERROR("Error sending %s: time out after %dms.\n",
763 get_cmd_string(cmd->id),
764 jiffies_to_msecs(HOST_COMPLETE_TIMEOUT));
766 clear_bit(STATUS_HCMD_ACTIVE, &priv->status);
772 if (test_bit(STATUS_RF_KILL_HW, &priv->status)) {
773 IWL_DEBUG_INFO("Command %s aborted: RF KILL Switch\n",
774 get_cmd_string(cmd->id));
778 if (test_bit(STATUS_FW_ERROR, &priv->status)) {
779 IWL_DEBUG_INFO("Command %s failed: FW Error\n",
780 get_cmd_string(cmd->id));
784 if ((cmd->meta.flags & CMD_WANT_SKB) && !cmd->meta.u.skb) {
785 IWL_ERROR("Error: Response NULL in '%s'\n",
786 get_cmd_string(cmd->id));
795 if (cmd->meta.flags & CMD_WANT_SKB) {
796 struct iwl3945_cmd *qcmd;
798 /* Cancel the CMD_WANT_SKB flag for the cmd in the
799 * TX cmd queue. Otherwise in case the cmd comes
800 * in later, it will possibly set an invalid
801 * address (cmd->meta.source). */
802 qcmd = &priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_idx];
803 qcmd->meta.flags &= ~CMD_WANT_SKB;
806 if (cmd->meta.u.skb) {
807 dev_kfree_skb_any(cmd->meta.u.skb);
808 cmd->meta.u.skb = NULL;
811 clear_bit(STATUS_HCMD_SYNC_ACTIVE, &priv->status);
815 int iwl3945_send_cmd(struct iwl3945_priv *priv, struct iwl3945_host_cmd *cmd)
817 if (cmd->meta.flags & CMD_ASYNC)
818 return iwl3945_send_cmd_async(priv, cmd);
820 return iwl3945_send_cmd_sync(priv, cmd);
823 int iwl3945_send_cmd_pdu(struct iwl3945_priv *priv, u8 id, u16 len, const void *data)
825 struct iwl3945_host_cmd cmd = {
831 return iwl3945_send_cmd_sync(priv, &cmd);
834 static int __must_check iwl3945_send_cmd_u32(struct iwl3945_priv *priv, u8 id, u32 val)
836 struct iwl3945_host_cmd cmd = {
842 return iwl3945_send_cmd_sync(priv, &cmd);
845 int iwl3945_send_statistics_request(struct iwl3945_priv *priv)
847 return iwl3945_send_cmd_u32(priv, REPLY_STATISTICS_CMD, 0);
851 * iwl3945_set_rxon_channel - Set the phymode and channel values in staging RXON
852 * @band: 2.4 or 5 GHz band
853 * @channel: Any channel valid for the requested band
855 * In addition to setting the staging RXON, priv->band is also set.
857 * NOTE: Does not commit to the hardware; it sets appropriate bit fields
858 * in the staging RXON flag structure based on the band
860 static int iwl3945_set_rxon_channel(struct iwl3945_priv *priv,
861 enum ieee80211_band band,
864 if (!iwl3945_get_channel_info(priv, band, channel)) {
865 IWL_DEBUG_INFO("Could not set channel to %d [%d]\n",
870 if ((le16_to_cpu(priv->staging_rxon.channel) == channel) &&
871 (priv->band == band))
874 priv->staging_rxon.channel = cpu_to_le16(channel);
875 if (band == IEEE80211_BAND_5GHZ)
876 priv->staging_rxon.flags &= ~RXON_FLG_BAND_24G_MSK;
878 priv->staging_rxon.flags |= RXON_FLG_BAND_24G_MSK;
882 IWL_DEBUG_INFO("Staging channel set to %d [%d]\n", channel, band);
888 * iwl3945_check_rxon_cmd - validate RXON structure is valid
890 * NOTE: This is really only useful during development and can eventually
891 * be #ifdef'd out once the driver is stable and folks aren't actively
894 static int iwl3945_check_rxon_cmd(struct iwl3945_rxon_cmd *rxon)
899 if (rxon->flags & RXON_FLG_BAND_24G_MSK) {
900 error |= le32_to_cpu(rxon->flags &
901 (RXON_FLG_TGJ_NARROW_BAND_MSK |
902 RXON_FLG_RADAR_DETECT_MSK));
904 IWL_WARNING("check 24G fields %d | %d\n",
907 error |= (rxon->flags & RXON_FLG_SHORT_SLOT_MSK) ?
908 0 : le32_to_cpu(RXON_FLG_SHORT_SLOT_MSK);
910 IWL_WARNING("check 52 fields %d | %d\n",
912 error |= le32_to_cpu(rxon->flags & RXON_FLG_CCK_MSK);
914 IWL_WARNING("check 52 CCK %d | %d\n",
917 error |= (rxon->node_addr[0] | rxon->bssid_addr[0]) & 0x1;
919 IWL_WARNING("check mac addr %d | %d\n", counter++, error);
921 /* make sure basic rates 6Mbps and 1Mbps are supported */
922 error |= (((rxon->ofdm_basic_rates & IWL_RATE_6M_MASK) == 0) &&
923 ((rxon->cck_basic_rates & IWL_RATE_1M_MASK) == 0));
925 IWL_WARNING("check basic rate %d | %d\n", counter++, error);
927 error |= (le16_to_cpu(rxon->assoc_id) > 2007);
929 IWL_WARNING("check assoc id %d | %d\n", counter++, error);
931 error |= ((rxon->flags & (RXON_FLG_CCK_MSK | RXON_FLG_SHORT_SLOT_MSK))
932 == (RXON_FLG_CCK_MSK | RXON_FLG_SHORT_SLOT_MSK));
934 IWL_WARNING("check CCK and short slot %d | %d\n",
937 error |= ((rxon->flags & (RXON_FLG_CCK_MSK | RXON_FLG_AUTO_DETECT_MSK))
938 == (RXON_FLG_CCK_MSK | RXON_FLG_AUTO_DETECT_MSK));
940 IWL_WARNING("check CCK & auto detect %d | %d\n",
943 error |= ((rxon->flags & (RXON_FLG_AUTO_DETECT_MSK |
944 RXON_FLG_TGG_PROTECT_MSK)) == RXON_FLG_TGG_PROTECT_MSK);
946 IWL_WARNING("check TGG and auto detect %d | %d\n",
949 if ((rxon->flags & RXON_FLG_DIS_DIV_MSK))
950 error |= ((rxon->flags & (RXON_FLG_ANT_B_MSK |
951 RXON_FLG_ANT_A_MSK)) == 0);
953 IWL_WARNING("check antenna %d %d\n", counter++, error);
956 IWL_WARNING("Tuning to channel %d\n",
957 le16_to_cpu(rxon->channel));
960 IWL_ERROR("Not a valid iwl3945_rxon_assoc_cmd field values\n");
967 * iwl3945_full_rxon_required - check if full RXON (vs RXON_ASSOC) cmd is needed
968 * @priv: staging_rxon is compared to active_rxon
970 * If the RXON structure is changing enough to require a new tune,
971 * or is clearing the RXON_FILTER_ASSOC_MSK, then return 1 to indicate that
972 * a new tune (full RXON command, rather than RXON_ASSOC cmd) is required.
974 static int iwl3945_full_rxon_required(struct iwl3945_priv *priv)
977 /* These items are only settable from the full RXON command */
978 if (!(iwl3945_is_associated(priv)) ||
979 compare_ether_addr(priv->staging_rxon.bssid_addr,
980 priv->active_rxon.bssid_addr) ||
981 compare_ether_addr(priv->staging_rxon.node_addr,
982 priv->active_rxon.node_addr) ||
983 compare_ether_addr(priv->staging_rxon.wlap_bssid_addr,
984 priv->active_rxon.wlap_bssid_addr) ||
985 (priv->staging_rxon.dev_type != priv->active_rxon.dev_type) ||
986 (priv->staging_rxon.channel != priv->active_rxon.channel) ||
987 (priv->staging_rxon.air_propagation !=
988 priv->active_rxon.air_propagation) ||
989 (priv->staging_rxon.assoc_id != priv->active_rxon.assoc_id))
992 /* flags, filter_flags, ofdm_basic_rates, and cck_basic_rates can
993 * be updated with the RXON_ASSOC command -- however only some
994 * flag transitions are allowed using RXON_ASSOC */
996 /* Check if we are not switching bands */
997 if ((priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) !=
998 (priv->active_rxon.flags & RXON_FLG_BAND_24G_MSK))
1001 /* Check if we are switching association toggle */
1002 if ((priv->staging_rxon.filter_flags & RXON_FILTER_ASSOC_MSK) !=
1003 (priv->active_rxon.filter_flags & RXON_FILTER_ASSOC_MSK))
1009 static int iwl3945_send_rxon_assoc(struct iwl3945_priv *priv)
1012 struct iwl3945_rx_packet *res = NULL;
1013 struct iwl3945_rxon_assoc_cmd rxon_assoc;
1014 struct iwl3945_host_cmd cmd = {
1015 .id = REPLY_RXON_ASSOC,
1016 .len = sizeof(rxon_assoc),
1017 .meta.flags = CMD_WANT_SKB,
1018 .data = &rxon_assoc,
1020 const struct iwl3945_rxon_cmd *rxon1 = &priv->staging_rxon;
1021 const struct iwl3945_rxon_cmd *rxon2 = &priv->active_rxon;
1023 if ((rxon1->flags == rxon2->flags) &&
1024 (rxon1->filter_flags == rxon2->filter_flags) &&
1025 (rxon1->cck_basic_rates == rxon2->cck_basic_rates) &&
1026 (rxon1->ofdm_basic_rates == rxon2->ofdm_basic_rates)) {
1027 IWL_DEBUG_INFO("Using current RXON_ASSOC. Not resending.\n");
1031 rxon_assoc.flags = priv->staging_rxon.flags;
1032 rxon_assoc.filter_flags = priv->staging_rxon.filter_flags;
1033 rxon_assoc.ofdm_basic_rates = priv->staging_rxon.ofdm_basic_rates;
1034 rxon_assoc.cck_basic_rates = priv->staging_rxon.cck_basic_rates;
1035 rxon_assoc.reserved = 0;
1037 rc = iwl3945_send_cmd_sync(priv, &cmd);
1041 res = (struct iwl3945_rx_packet *)cmd.meta.u.skb->data;
1042 if (res->hdr.flags & IWL_CMD_FAILED_MSK) {
1043 IWL_ERROR("Bad return from REPLY_RXON_ASSOC command\n");
1047 priv->alloc_rxb_skb--;
1048 dev_kfree_skb_any(cmd.meta.u.skb);
1054 * iwl3945_commit_rxon - commit staging_rxon to hardware
1056 * The RXON command in staging_rxon is committed to the hardware and
1057 * the active_rxon structure is updated with the new data. This
1058 * function correctly transitions out of the RXON_ASSOC_MSK state if
1059 * a HW tune is required based on the RXON structure changes.
1061 static int iwl3945_commit_rxon(struct iwl3945_priv *priv)
1063 /* cast away the const for active_rxon in this function */
1064 struct iwl3945_rxon_cmd *active_rxon = (void *)&priv->active_rxon;
1066 DECLARE_MAC_BUF(mac);
1068 if (!iwl3945_is_alive(priv))
1071 /* always get timestamp with Rx frame */
1072 priv->staging_rxon.flags |= RXON_FLG_TSF2HOST_MSK;
1074 /* select antenna */
1075 priv->staging_rxon.flags &=
1076 ~(RXON_FLG_DIS_DIV_MSK | RXON_FLG_ANT_SEL_MSK);
1077 priv->staging_rxon.flags |= iwl3945_get_antenna_flags(priv);
1079 rc = iwl3945_check_rxon_cmd(&priv->staging_rxon);
1081 IWL_ERROR("Invalid RXON configuration. Not committing.\n");
1085 /* If we don't need to send a full RXON, we can use
1086 * iwl3945_rxon_assoc_cmd which is used to reconfigure filter
1087 * and other flags for the current radio configuration. */
1088 if (!iwl3945_full_rxon_required(priv)) {
1089 rc = iwl3945_send_rxon_assoc(priv);
1091 IWL_ERROR("Error setting RXON_ASSOC "
1092 "configuration (%d).\n", rc);
1096 memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
1101 /* If we are currently associated and the new config requires
1102 * an RXON_ASSOC and the new config wants the associated mask enabled,
1103 * we must clear the associated from the active configuration
1104 * before we apply the new config */
1105 if (iwl3945_is_associated(priv) &&
1106 (priv->staging_rxon.filter_flags & RXON_FILTER_ASSOC_MSK)) {
1107 IWL_DEBUG_INFO("Toggling associated bit on current RXON\n");
1108 active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;
1110 rc = iwl3945_send_cmd_pdu(priv, REPLY_RXON,
1111 sizeof(struct iwl3945_rxon_cmd),
1112 &priv->active_rxon);
1114 /* If the mask clearing failed then we set
1115 * active_rxon back to what it was previously */
1117 active_rxon->filter_flags |= RXON_FILTER_ASSOC_MSK;
1118 IWL_ERROR("Error clearing ASSOC_MSK on current "
1119 "configuration (%d).\n", rc);
1124 IWL_DEBUG_INFO("Sending RXON\n"
1125 "* with%s RXON_FILTER_ASSOC_MSK\n"
1128 ((priv->staging_rxon.filter_flags &
1129 RXON_FILTER_ASSOC_MSK) ? "" : "out"),
1130 le16_to_cpu(priv->staging_rxon.channel),
1131 print_mac(mac, priv->staging_rxon.bssid_addr));
1133 /* Apply the new configuration */
1134 rc = iwl3945_send_cmd_pdu(priv, REPLY_RXON,
1135 sizeof(struct iwl3945_rxon_cmd), &priv->staging_rxon);
1137 IWL_ERROR("Error setting new configuration (%d).\n", rc);
1141 memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
1143 iwl3945_clear_stations_table(priv);
1145 /* If we issue a new RXON command which required a tune then we must
1146 * send a new TXPOWER command or we won't be able to Tx any frames */
1147 rc = iwl3945_hw_reg_send_txpower(priv);
1149 IWL_ERROR("Error setting Tx power (%d).\n", rc);
1153 /* Add the broadcast address so we can send broadcast frames */
1154 if (iwl3945_add_station(priv, iwl3945_broadcast_addr, 0, 0) ==
1155 IWL_INVALID_STATION) {
1156 IWL_ERROR("Error adding BROADCAST address for transmit.\n");
1160 /* If we have set the ASSOC_MSK and we are in BSS mode then
1161 * add the IWL_AP_ID to the station rate table */
1162 if (iwl3945_is_associated(priv) &&
1163 (priv->iw_mode == NL80211_IFTYPE_STATION))
1164 if (iwl3945_add_station(priv, priv->active_rxon.bssid_addr, 1, 0)
1165 == IWL_INVALID_STATION) {
1166 IWL_ERROR("Error adding AP address for transmit.\n");
1170 /* Init the hardware's rate fallback order based on the band */
1171 rc = iwl3945_init_hw_rate_table(priv);
1173 IWL_ERROR("Error setting HW rate table: %02X\n", rc);
1180 static int iwl3945_send_bt_config(struct iwl3945_priv *priv)
1182 struct iwl3945_bt_cmd bt_cmd = {
1190 return iwl3945_send_cmd_pdu(priv, REPLY_BT_CONFIG,
1191 sizeof(struct iwl3945_bt_cmd), &bt_cmd);
1194 static int iwl3945_send_scan_abort(struct iwl3945_priv *priv)
1197 struct iwl3945_rx_packet *res;
1198 struct iwl3945_host_cmd cmd = {
1199 .id = REPLY_SCAN_ABORT_CMD,
1200 .meta.flags = CMD_WANT_SKB,
1203 /* If there isn't a scan actively going on in the hardware
1204 * then we are in between scan bands and not actually
1205 * actively scanning, so don't send the abort command */
1206 if (!test_bit(STATUS_SCAN_HW, &priv->status)) {
1207 clear_bit(STATUS_SCAN_ABORTING, &priv->status);
1211 rc = iwl3945_send_cmd_sync(priv, &cmd);
1213 clear_bit(STATUS_SCAN_ABORTING, &priv->status);
1217 res = (struct iwl3945_rx_packet *)cmd.meta.u.skb->data;
1218 if (res->u.status != CAN_ABORT_STATUS) {
1219 /* The scan abort will return 1 for success or
1220 * 2 for "failure". A failure condition can be
1221 * due to simply not being in an active scan which
1222 * can occur if we send the scan abort before we
1223 * the microcode has notified us that a scan is
1225 IWL_DEBUG_INFO("SCAN_ABORT returned %d.\n", res->u.status);
1226 clear_bit(STATUS_SCAN_ABORTING, &priv->status);
1227 clear_bit(STATUS_SCAN_HW, &priv->status);
1230 dev_kfree_skb_any(cmd.meta.u.skb);
1235 static int iwl3945_card_state_sync_callback(struct iwl3945_priv *priv,
1236 struct iwl3945_cmd *cmd,
1237 struct sk_buff *skb)
1245 * Use: Sets the device's internal card state to enable, disable, or halt
1247 * When in the 'enable' state the card operates as normal.
1248 * When in the 'disable' state, the card enters into a low power mode.
1249 * When in the 'halt' state, the card is shut down and must be fully
1250 * restarted to come back on.
1252 static int iwl3945_send_card_state(struct iwl3945_priv *priv, u32 flags, u8 meta_flag)
1254 struct iwl3945_host_cmd cmd = {
1255 .id = REPLY_CARD_STATE_CMD,
1258 .meta.flags = meta_flag,
1261 if (meta_flag & CMD_ASYNC)
1262 cmd.meta.u.callback = iwl3945_card_state_sync_callback;
1264 return iwl3945_send_cmd(priv, &cmd);
1267 static int iwl3945_add_sta_sync_callback(struct iwl3945_priv *priv,
1268 struct iwl3945_cmd *cmd, struct sk_buff *skb)
1270 struct iwl3945_rx_packet *res = NULL;
1273 IWL_ERROR("Error: Response NULL in REPLY_ADD_STA.\n");
1277 res = (struct iwl3945_rx_packet *)skb->data;
1278 if (res->hdr.flags & IWL_CMD_FAILED_MSK) {
1279 IWL_ERROR("Bad return from REPLY_ADD_STA (0x%08X)\n",
1284 switch (res->u.add_sta.status) {
1285 case ADD_STA_SUCCESS_MSK:
1291 /* We didn't cache the SKB; let the caller free it */
1295 int iwl3945_send_add_station(struct iwl3945_priv *priv,
1296 struct iwl3945_addsta_cmd *sta, u8 flags)
1298 struct iwl3945_rx_packet *res = NULL;
1300 struct iwl3945_host_cmd cmd = {
1301 .id = REPLY_ADD_STA,
1302 .len = sizeof(struct iwl3945_addsta_cmd),
1303 .meta.flags = flags,
1307 if (flags & CMD_ASYNC)
1308 cmd.meta.u.callback = iwl3945_add_sta_sync_callback;
1310 cmd.meta.flags |= CMD_WANT_SKB;
1312 rc = iwl3945_send_cmd(priv, &cmd);
1314 if (rc || (flags & CMD_ASYNC))
1317 res = (struct iwl3945_rx_packet *)cmd.meta.u.skb->data;
1318 if (res->hdr.flags & IWL_CMD_FAILED_MSK) {
1319 IWL_ERROR("Bad return from REPLY_ADD_STA (0x%08X)\n",
1325 switch (res->u.add_sta.status) {
1326 case ADD_STA_SUCCESS_MSK:
1327 IWL_DEBUG_INFO("REPLY_ADD_STA PASSED\n");
1331 IWL_WARNING("REPLY_ADD_STA failed\n");
1336 priv->alloc_rxb_skb--;
1337 dev_kfree_skb_any(cmd.meta.u.skb);
1342 static int iwl3945_update_sta_key_info(struct iwl3945_priv *priv,
1343 struct ieee80211_key_conf *keyconf,
1346 unsigned long flags;
1347 __le16 key_flags = 0;
1349 switch (keyconf->alg) {
1351 key_flags |= STA_KEY_FLG_CCMP;
1352 key_flags |= cpu_to_le16(
1353 keyconf->keyidx << STA_KEY_FLG_KEYID_POS);
1354 key_flags &= ~STA_KEY_FLG_INVALID;
1361 spin_lock_irqsave(&priv->sta_lock, flags);
1362 priv->stations[sta_id].keyinfo.alg = keyconf->alg;
1363 priv->stations[sta_id].keyinfo.keylen = keyconf->keylen;
1364 memcpy(priv->stations[sta_id].keyinfo.key, keyconf->key,
1367 memcpy(priv->stations[sta_id].sta.key.key, keyconf->key,
1369 priv->stations[sta_id].sta.key.key_flags = key_flags;
1370 priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK;
1371 priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK;
1373 spin_unlock_irqrestore(&priv->sta_lock, flags);
1375 IWL_DEBUG_INFO("hwcrypto: modify ucode station key info\n");
1376 iwl3945_send_add_station(priv, &priv->stations[sta_id].sta, 0);
1380 static int iwl3945_clear_sta_key_info(struct iwl3945_priv *priv, u8 sta_id)
1382 unsigned long flags;
1384 spin_lock_irqsave(&priv->sta_lock, flags);
1385 memset(&priv->stations[sta_id].keyinfo, 0, sizeof(struct iwl3945_hw_key));
1386 memset(&priv->stations[sta_id].sta.key, 0, sizeof(struct iwl3945_keyinfo));
1387 priv->stations[sta_id].sta.key.key_flags = STA_KEY_FLG_NO_ENC;
1388 priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK;
1389 priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK;
1390 spin_unlock_irqrestore(&priv->sta_lock, flags);
1392 IWL_DEBUG_INFO("hwcrypto: clear ucode station key info\n");
1393 iwl3945_send_add_station(priv, &priv->stations[sta_id].sta, 0);
1397 static void iwl3945_clear_free_frames(struct iwl3945_priv *priv)
1399 struct list_head *element;
1401 IWL_DEBUG_INFO("%d frames on pre-allocated heap on clear.\n",
1402 priv->frames_count);
1404 while (!list_empty(&priv->free_frames)) {
1405 element = priv->free_frames.next;
1407 kfree(list_entry(element, struct iwl3945_frame, list));
1408 priv->frames_count--;
1411 if (priv->frames_count) {
1412 IWL_WARNING("%d frames still in use. Did we lose one?\n",
1413 priv->frames_count);
1414 priv->frames_count = 0;
1418 static struct iwl3945_frame *iwl3945_get_free_frame(struct iwl3945_priv *priv)
1420 struct iwl3945_frame *frame;
1421 struct list_head *element;
1422 if (list_empty(&priv->free_frames)) {
1423 frame = kzalloc(sizeof(*frame), GFP_KERNEL);
1425 IWL_ERROR("Could not allocate frame!\n");
1429 priv->frames_count++;
1433 element = priv->free_frames.next;
1435 return list_entry(element, struct iwl3945_frame, list);
1438 static void iwl3945_free_frame(struct iwl3945_priv *priv, struct iwl3945_frame *frame)
1440 memset(frame, 0, sizeof(*frame));
1441 list_add(&frame->list, &priv->free_frames);
1444 unsigned int iwl3945_fill_beacon_frame(struct iwl3945_priv *priv,
1445 struct ieee80211_hdr *hdr,
1446 const u8 *dest, int left)
1449 if (!iwl3945_is_associated(priv) || !priv->ibss_beacon ||
1450 ((priv->iw_mode != NL80211_IFTYPE_ADHOC) &&
1451 (priv->iw_mode != NL80211_IFTYPE_AP)))
1454 if (priv->ibss_beacon->len > left)
1457 memcpy(hdr, priv->ibss_beacon->data, priv->ibss_beacon->len);
1459 return priv->ibss_beacon->len;
1462 static u8 iwl3945_rate_get_lowest_plcp(int rate_mask)
1466 for (i = IWL_RATE_1M_INDEX; i != IWL_RATE_INVALID;
1467 i = iwl3945_rates[i].next_ieee) {
1468 if (rate_mask & (1 << i))
1469 return iwl3945_rates[i].plcp;
1472 return IWL_RATE_INVALID;
1475 static int iwl3945_send_beacon_cmd(struct iwl3945_priv *priv)
1477 struct iwl3945_frame *frame;
1478 unsigned int frame_size;
1482 frame = iwl3945_get_free_frame(priv);
1485 IWL_ERROR("Could not obtain free frame buffer for beacon "
1490 if (!(priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK)) {
1491 rate = iwl3945_rate_get_lowest_plcp(priv->active_rate_basic &
1493 if (rate == IWL_INVALID_RATE)
1494 rate = IWL_RATE_6M_PLCP;
1496 rate = iwl3945_rate_get_lowest_plcp(priv->active_rate_basic & 0xF);
1497 if (rate == IWL_INVALID_RATE)
1498 rate = IWL_RATE_1M_PLCP;
1501 frame_size = iwl3945_hw_get_beacon_cmd(priv, frame, rate);
1503 rc = iwl3945_send_cmd_pdu(priv, REPLY_TX_BEACON, frame_size,
1506 iwl3945_free_frame(priv, frame);
1511 /******************************************************************************
1513 * EEPROM related functions
1515 ******************************************************************************/
1517 static void get_eeprom_mac(struct iwl3945_priv *priv, u8 *mac)
1519 memcpy(mac, priv->eeprom.mac_address, 6);
1523 * Clear the OWNER_MSK, to establish driver (instead of uCode running on
1524 * embedded controller) as EEPROM reader; each read is a series of pulses
1525 * to/from the EEPROM chip, not a single event, so even reads could conflict
1526 * if they weren't arbitrated by some ownership mechanism. Here, the driver
1527 * simply claims ownership, which should be safe when this function is called
1528 * (i.e. before loading uCode!).
1530 static inline int iwl3945_eeprom_acquire_semaphore(struct iwl3945_priv *priv)
1532 _iwl3945_clear_bit(priv, CSR_EEPROM_GP, CSR_EEPROM_GP_IF_OWNER_MSK);
1537 * iwl3945_eeprom_init - read EEPROM contents
1539 * Load the EEPROM contents from adapter into priv->eeprom
1541 * NOTE: This routine uses the non-debug IO access functions.
1543 int iwl3945_eeprom_init(struct iwl3945_priv *priv)
1545 u16 *e = (u16 *)&priv->eeprom;
1546 u32 gp = iwl3945_read32(priv, CSR_EEPROM_GP);
1548 int sz = sizeof(priv->eeprom);
1553 /* The EEPROM structure has several padding buffers within it
1554 * and when adding new EEPROM maps is subject to programmer errors
1555 * which may be very difficult to identify without explicitly
1556 * checking the resulting size of the eeprom map. */
1557 BUILD_BUG_ON(sizeof(priv->eeprom) != IWL_EEPROM_IMAGE_SIZE);
1559 if ((gp & CSR_EEPROM_GP_VALID_MSK) == CSR_EEPROM_GP_BAD_SIGNATURE) {
1560 IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x\n", gp);
1564 /* Make sure driver (instead of uCode) is allowed to read EEPROM */
1565 rc = iwl3945_eeprom_acquire_semaphore(priv);
1567 IWL_ERROR("Failed to acquire EEPROM semaphore.\n");
1571 /* eeprom is an array of 16bit values */
1572 for (addr = 0; addr < sz; addr += sizeof(u16)) {
1573 _iwl3945_write32(priv, CSR_EEPROM_REG, addr << 1);
1574 _iwl3945_clear_bit(priv, CSR_EEPROM_REG, CSR_EEPROM_REG_BIT_CMD);
1576 for (i = 0; i < IWL_EEPROM_ACCESS_TIMEOUT;
1577 i += IWL_EEPROM_ACCESS_DELAY) {
1578 r = _iwl3945_read_direct32(priv, CSR_EEPROM_REG);
1579 if (r & CSR_EEPROM_REG_READ_VALID_MSK)
1581 udelay(IWL_EEPROM_ACCESS_DELAY);
1584 if (!(r & CSR_EEPROM_REG_READ_VALID_MSK)) {
1585 IWL_ERROR("Time out reading EEPROM[%d]\n", addr);
1588 e[addr / 2] = le16_to_cpu((__force __le16)(r >> 16));
1594 static void iwl3945_unset_hw_setting(struct iwl3945_priv *priv)
1596 if (priv->hw_setting.shared_virt)
1597 pci_free_consistent(priv->pci_dev,
1598 sizeof(struct iwl3945_shared),
1599 priv->hw_setting.shared_virt,
1600 priv->hw_setting.shared_phys);
1604 * iwl3945_supported_rate_to_ie - fill in the supported rate in IE field
1606 * return : set the bit for each supported rate insert in ie
1608 static u16 iwl3945_supported_rate_to_ie(u8 *ie, u16 supported_rate,
1609 u16 basic_rate, int *left)
1611 u16 ret_rates = 0, bit;
1616 for (bit = 1, i = 0; i < IWL_RATE_COUNT; i++, bit <<= 1) {
1617 if (bit & supported_rate) {
1619 rates[*cnt] = iwl3945_rates[i].ieee |
1620 ((bit & basic_rate) ? 0x80 : 0x00);
1624 (*cnt >= IWL_SUPPORTED_RATES_IE_LEN))
1633 * iwl3945_fill_probe_req - fill in all required fields and IE for probe request
1635 static u16 iwl3945_fill_probe_req(struct iwl3945_priv *priv,
1636 struct ieee80211_mgmt *frame,
1637 int left, int is_direct)
1641 u16 active_rates, ret_rates, cck_rates;
1643 /* Make sure there is enough space for the probe request,
1644 * two mandatory IEs and the data */
1650 frame->frame_control = cpu_to_le16(IEEE80211_STYPE_PROBE_REQ);
1651 memcpy(frame->da, iwl3945_broadcast_addr, ETH_ALEN);
1652 memcpy(frame->sa, priv->mac_addr, ETH_ALEN);
1653 memcpy(frame->bssid, iwl3945_broadcast_addr, ETH_ALEN);
1654 frame->seq_ctrl = 0;
1656 /* fill in our indirect SSID IE */
1663 pos = &(frame->u.probe_req.variable[0]);
1664 *pos++ = WLAN_EID_SSID;
1667 /* fill in our direct SSID IE... */
1670 left -= 2 + priv->essid_len;
1673 /* ... fill it in... */
1674 *pos++ = WLAN_EID_SSID;
1675 *pos++ = priv->essid_len;
1676 memcpy(pos, priv->essid, priv->essid_len);
1677 pos += priv->essid_len;
1678 len += 2 + priv->essid_len;
1681 /* fill in supported rate */
1687 /* ... fill it in... */
1688 *pos++ = WLAN_EID_SUPP_RATES;
1691 priv->active_rate = priv->rates_mask;
1692 active_rates = priv->active_rate;
1693 priv->active_rate_basic = priv->rates_mask & IWL_BASIC_RATES_MASK;
1695 cck_rates = IWL_CCK_RATES_MASK & active_rates;
1696 ret_rates = iwl3945_supported_rate_to_ie(pos, cck_rates,
1697 priv->active_rate_basic, &left);
1698 active_rates &= ~ret_rates;
1700 ret_rates = iwl3945_supported_rate_to_ie(pos, active_rates,
1701 priv->active_rate_basic, &left);
1702 active_rates &= ~ret_rates;
1706 if (active_rates == 0)
1709 /* fill in supported extended rate */
1714 /* ... fill it in... */
1715 *pos++ = WLAN_EID_EXT_SUPP_RATES;
1717 iwl3945_supported_rate_to_ie(pos, active_rates,
1718 priv->active_rate_basic, &left);
1729 static int iwl3945_send_qos_params_command(struct iwl3945_priv *priv,
1730 struct iwl3945_qosparam_cmd *qos)
1733 return iwl3945_send_cmd_pdu(priv, REPLY_QOS_PARAM,
1734 sizeof(struct iwl3945_qosparam_cmd), qos);
1737 static void iwl3945_reset_qos(struct iwl3945_priv *priv)
1743 unsigned long flags;
1746 spin_lock_irqsave(&priv->lock, flags);
1747 priv->qos_data.qos_active = 0;
1749 if (priv->iw_mode == NL80211_IFTYPE_ADHOC) {
1750 if (priv->qos_data.qos_enable)
1751 priv->qos_data.qos_active = 1;
1752 if (!(priv->active_rate & 0xfff0)) {
1756 } else if (priv->iw_mode == NL80211_IFTYPE_AP) {
1757 if (priv->qos_data.qos_enable)
1758 priv->qos_data.qos_active = 1;
1759 } else if (!(priv->staging_rxon.flags & RXON_FLG_SHORT_SLOT_MSK)) {
1764 if (priv->qos_data.qos_active)
1767 priv->qos_data.def_qos_parm.ac[0].cw_min = cpu_to_le16(cw_min);
1768 priv->qos_data.def_qos_parm.ac[0].cw_max = cpu_to_le16(cw_max);
1769 priv->qos_data.def_qos_parm.ac[0].aifsn = aifs;
1770 priv->qos_data.def_qos_parm.ac[0].edca_txop = 0;
1771 priv->qos_data.def_qos_parm.ac[0].reserved1 = 0;
1773 if (priv->qos_data.qos_active) {
1775 priv->qos_data.def_qos_parm.ac[i].cw_min = cpu_to_le16(cw_min);
1776 priv->qos_data.def_qos_parm.ac[i].cw_max = cpu_to_le16(cw_max);
1777 priv->qos_data.def_qos_parm.ac[i].aifsn = 7;
1778 priv->qos_data.def_qos_parm.ac[i].edca_txop = 0;
1779 priv->qos_data.def_qos_parm.ac[i].reserved1 = 0;
1782 priv->qos_data.def_qos_parm.ac[i].cw_min =
1783 cpu_to_le16((cw_min + 1) / 2 - 1);
1784 priv->qos_data.def_qos_parm.ac[i].cw_max =
1785 cpu_to_le16(cw_max);
1786 priv->qos_data.def_qos_parm.ac[i].aifsn = 2;
1788 priv->qos_data.def_qos_parm.ac[i].edca_txop =
1791 priv->qos_data.def_qos_parm.ac[i].edca_txop =
1793 priv->qos_data.def_qos_parm.ac[i].reserved1 = 0;
1796 priv->qos_data.def_qos_parm.ac[i].cw_min =
1797 cpu_to_le16((cw_min + 1) / 4 - 1);
1798 priv->qos_data.def_qos_parm.ac[i].cw_max =
1799 cpu_to_le16((cw_max + 1) / 2 - 1);
1800 priv->qos_data.def_qos_parm.ac[i].aifsn = 2;
1801 priv->qos_data.def_qos_parm.ac[i].reserved1 = 0;
1803 priv->qos_data.def_qos_parm.ac[i].edca_txop =
1806 priv->qos_data.def_qos_parm.ac[i].edca_txop =
1809 for (i = 1; i < 4; i++) {
1810 priv->qos_data.def_qos_parm.ac[i].cw_min =
1811 cpu_to_le16(cw_min);
1812 priv->qos_data.def_qos_parm.ac[i].cw_max =
1813 cpu_to_le16(cw_max);
1814 priv->qos_data.def_qos_parm.ac[i].aifsn = aifs;
1815 priv->qos_data.def_qos_parm.ac[i].edca_txop = 0;
1816 priv->qos_data.def_qos_parm.ac[i].reserved1 = 0;
1819 IWL_DEBUG_QOS("set QoS to default \n");
1821 spin_unlock_irqrestore(&priv->lock, flags);
1824 static void iwl3945_activate_qos(struct iwl3945_priv *priv, u8 force)
1826 unsigned long flags;
1828 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1831 if (!priv->qos_data.qos_enable)
1834 spin_lock_irqsave(&priv->lock, flags);
1835 priv->qos_data.def_qos_parm.qos_flags = 0;
1837 if (priv->qos_data.qos_cap.q_AP.queue_request &&
1838 !priv->qos_data.qos_cap.q_AP.txop_request)
1839 priv->qos_data.def_qos_parm.qos_flags |=
1840 QOS_PARAM_FLG_TXOP_TYPE_MSK;
1842 if (priv->qos_data.qos_active)
1843 priv->qos_data.def_qos_parm.qos_flags |=
1844 QOS_PARAM_FLG_UPDATE_EDCA_MSK;
1846 spin_unlock_irqrestore(&priv->lock, flags);
1848 if (force || iwl3945_is_associated(priv)) {
1849 IWL_DEBUG_QOS("send QoS cmd with Qos active %d \n",
1850 priv->qos_data.qos_active);
1852 iwl3945_send_qos_params_command(priv,
1853 &(priv->qos_data.def_qos_parm));
1858 * Power management (not Tx power!) functions
1860 #define MSEC_TO_USEC 1024
1862 #define NOSLP __constant_cpu_to_le32(0)
1863 #define SLP IWL_POWER_DRIVER_ALLOW_SLEEP_MSK
1864 #define SLP_TIMEOUT(T) __constant_cpu_to_le32((T) * MSEC_TO_USEC)
1865 #define SLP_VEC(X0, X1, X2, X3, X4) {__constant_cpu_to_le32(X0), \
1866 __constant_cpu_to_le32(X1), \
1867 __constant_cpu_to_le32(X2), \
1868 __constant_cpu_to_le32(X3), \
1869 __constant_cpu_to_le32(X4)}
1872 /* default power management (not Tx power) table values */
1874 static struct iwl3945_power_vec_entry range_0[IWL_POWER_AC] = {
1875 {{NOSLP, SLP_TIMEOUT(0), SLP_TIMEOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
1876 {{SLP, SLP_TIMEOUT(200), SLP_TIMEOUT(500), SLP_VEC(1, 2, 3, 4, 4)}, 0},
1877 {{SLP, SLP_TIMEOUT(200), SLP_TIMEOUT(300), SLP_VEC(2, 4, 6, 7, 7)}, 0},
1878 {{SLP, SLP_TIMEOUT(50), SLP_TIMEOUT(100), SLP_VEC(2, 6, 9, 9, 10)}, 0},
1879 {{SLP, SLP_TIMEOUT(50), SLP_TIMEOUT(25), SLP_VEC(2, 7, 9, 9, 10)}, 1},
1880 {{SLP, SLP_TIMEOUT(25), SLP_TIMEOUT(25), SLP_VEC(4, 7, 10, 10, 10)}, 1}
1884 static struct iwl3945_power_vec_entry range_1[IWL_POWER_AC] = {
1885 {{NOSLP, SLP_TIMEOUT(0), SLP_TIMEOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
1886 {{SLP, SLP_TIMEOUT(200), SLP_TIMEOUT(500),
1887 SLP_VEC(1, 2, 3, 4, 0xFF)}, 0},
1888 {{SLP, SLP_TIMEOUT(200), SLP_TIMEOUT(300),
1889 SLP_VEC(2, 4, 6, 7, 0xFF)}, 0},
1890 {{SLP, SLP_TIMEOUT(50), SLP_TIMEOUT(100),
1891 SLP_VEC(2, 6, 9, 9, 0xFF)}, 0},
1892 {{SLP, SLP_TIMEOUT(50), SLP_TIMEOUT(25), SLP_VEC(2, 7, 9, 9, 0xFF)}, 0},
1893 {{SLP, SLP_TIMEOUT(25), SLP_TIMEOUT(25),
1894 SLP_VEC(4, 7, 10, 10, 0xFF)}, 0}
1897 int iwl3945_power_init_handle(struct iwl3945_priv *priv)
1900 struct iwl3945_power_mgr *pow_data;
1901 int size = sizeof(struct iwl3945_power_vec_entry) * IWL_POWER_AC;
1904 IWL_DEBUG_POWER("Initialize power \n");
1906 pow_data = &(priv->power_data);
1908 memset(pow_data, 0, sizeof(*pow_data));
1910 pow_data->active_index = IWL_POWER_RANGE_0;
1911 pow_data->dtim_val = 0xffff;
1913 memcpy(&pow_data->pwr_range_0[0], &range_0[0], size);
1914 memcpy(&pow_data->pwr_range_1[0], &range_1[0], size);
1916 rc = pci_read_config_word(priv->pci_dev, PCI_LINK_CTRL, &pci_pm);
1920 struct iwl3945_powertable_cmd *cmd;
1922 IWL_DEBUG_POWER("adjust power command flags\n");
1924 for (i = 0; i < IWL_POWER_AC; i++) {
1925 cmd = &pow_data->pwr_range_0[i].cmd;
1928 cmd->flags &= ~IWL_POWER_PCI_PM_MSK;
1930 cmd->flags |= IWL_POWER_PCI_PM_MSK;
1936 static int iwl3945_update_power_cmd(struct iwl3945_priv *priv,
1937 struct iwl3945_powertable_cmd *cmd, u32 mode)
1942 struct iwl3945_power_vec_entry *range;
1944 struct iwl3945_power_mgr *pow_data;
1946 if (mode > IWL_POWER_INDEX_5) {
1947 IWL_DEBUG_POWER("Error invalid power mode \n");
1950 pow_data = &(priv->power_data);
1952 if (pow_data->active_index == IWL_POWER_RANGE_0)
1953 range = &pow_data->pwr_range_0[0];
1955 range = &pow_data->pwr_range_1[1];
1957 memcpy(cmd, &range[mode].cmd, sizeof(struct iwl3945_powertable_cmd));
1959 #ifdef IWL_MAC80211_DISABLE
1960 if (priv->assoc_network != NULL) {
1961 unsigned long flags;
1963 period = priv->assoc_network->tim.tim_period;
1965 #endif /*IWL_MAC80211_DISABLE */
1966 skip = range[mode].no_dtim;
1975 cmd->flags &= ~IWL_POWER_SLEEP_OVER_DTIM_MSK;
1977 __le32 slp_itrvl = cmd->sleep_interval[IWL_POWER_VEC_SIZE - 1];
1978 max_sleep = (le32_to_cpu(slp_itrvl) / period) * period;
1979 cmd->flags |= IWL_POWER_SLEEP_OVER_DTIM_MSK;
1982 for (i = 0; i < IWL_POWER_VEC_SIZE; i++) {
1983 if (le32_to_cpu(cmd->sleep_interval[i]) > max_sleep)
1984 cmd->sleep_interval[i] = cpu_to_le32(max_sleep);
1987 IWL_DEBUG_POWER("Flags value = 0x%08X\n", cmd->flags);
1988 IWL_DEBUG_POWER("Tx timeout = %u\n", le32_to_cpu(cmd->tx_data_timeout));
1989 IWL_DEBUG_POWER("Rx timeout = %u\n", le32_to_cpu(cmd->rx_data_timeout));
1990 IWL_DEBUG_POWER("Sleep interval vector = { %d , %d , %d , %d , %d }\n",
1991 le32_to_cpu(cmd->sleep_interval[0]),
1992 le32_to_cpu(cmd->sleep_interval[1]),
1993 le32_to_cpu(cmd->sleep_interval[2]),
1994 le32_to_cpu(cmd->sleep_interval[3]),
1995 le32_to_cpu(cmd->sleep_interval[4]));
2000 static int iwl3945_send_power_mode(struct iwl3945_priv *priv, u32 mode)
2002 u32 uninitialized_var(final_mode);
2004 struct iwl3945_powertable_cmd cmd;
2006 /* If on battery, set to 3,
2007 * if plugged into AC power, set to CAM ("continuously aware mode"),
2008 * else user level */
2010 case IWL_POWER_BATTERY:
2011 final_mode = IWL_POWER_INDEX_3;
2014 final_mode = IWL_POWER_MODE_CAM;
2021 iwl3945_update_power_cmd(priv, &cmd, final_mode);
2023 rc = iwl3945_send_cmd_pdu(priv, POWER_TABLE_CMD, sizeof(cmd), &cmd);
2025 if (final_mode == IWL_POWER_MODE_CAM)
2026 clear_bit(STATUS_POWER_PMI, &priv->status);
2028 set_bit(STATUS_POWER_PMI, &priv->status);
2034 * iwl3945_scan_cancel - Cancel any currently executing HW scan
2036 * NOTE: priv->mutex is not required before calling this function
2038 static int iwl3945_scan_cancel(struct iwl3945_priv *priv)
2040 if (!test_bit(STATUS_SCAN_HW, &priv->status)) {
2041 clear_bit(STATUS_SCANNING, &priv->status);
2045 if (test_bit(STATUS_SCANNING, &priv->status)) {
2046 if (!test_bit(STATUS_SCAN_ABORTING, &priv->status)) {
2047 IWL_DEBUG_SCAN("Queuing scan abort.\n");
2048 set_bit(STATUS_SCAN_ABORTING, &priv->status);
2049 queue_work(priv->workqueue, &priv->abort_scan);
2052 IWL_DEBUG_SCAN("Scan abort already in progress.\n");
2054 return test_bit(STATUS_SCANNING, &priv->status);
2061 * iwl3945_scan_cancel_timeout - Cancel any currently executing HW scan
2062 * @ms: amount of time to wait (in milliseconds) for scan to abort
2064 * NOTE: priv->mutex must be held before calling this function
2066 static int iwl3945_scan_cancel_timeout(struct iwl3945_priv *priv, unsigned long ms)
2068 unsigned long now = jiffies;
2071 ret = iwl3945_scan_cancel(priv);
2073 mutex_unlock(&priv->mutex);
2074 while (!time_after(jiffies, now + msecs_to_jiffies(ms)) &&
2075 test_bit(STATUS_SCANNING, &priv->status))
2077 mutex_lock(&priv->mutex);
2079 return test_bit(STATUS_SCANNING, &priv->status);
2085 #define MAX_UCODE_BEACON_INTERVAL 1024
2086 #define INTEL_CONN_LISTEN_INTERVAL __constant_cpu_to_le16(0xA)
2088 static __le16 iwl3945_adjust_beacon_interval(u16 beacon_val)
2091 u16 beacon_factor = 0;
2094 (beacon_val + MAX_UCODE_BEACON_INTERVAL)
2095 / MAX_UCODE_BEACON_INTERVAL;
2096 new_val = beacon_val / beacon_factor;
2098 return cpu_to_le16(new_val);
2101 static void iwl3945_setup_rxon_timing(struct iwl3945_priv *priv)
2103 u64 interval_tm_unit;
2105 unsigned long flags;
2106 struct ieee80211_conf *conf = NULL;
2109 conf = ieee80211_get_hw_conf(priv->hw);
2111 spin_lock_irqsave(&priv->lock, flags);
2112 priv->rxon_timing.timestamp.dw[1] = cpu_to_le32(priv->timestamp1);
2113 priv->rxon_timing.timestamp.dw[0] = cpu_to_le32(priv->timestamp0);
2115 priv->rxon_timing.listen_interval = INTEL_CONN_LISTEN_INTERVAL;
2117 tsf = priv->timestamp1;
2118 tsf = ((tsf << 32) | priv->timestamp0);
2120 beacon_int = priv->beacon_int;
2121 spin_unlock_irqrestore(&priv->lock, flags);
2123 if (priv->iw_mode == NL80211_IFTYPE_STATION) {
2124 if (beacon_int == 0) {
2125 priv->rxon_timing.beacon_interval = cpu_to_le16(100);
2126 priv->rxon_timing.beacon_init_val = cpu_to_le32(102400);
2128 priv->rxon_timing.beacon_interval =
2129 cpu_to_le16(beacon_int);
2130 priv->rxon_timing.beacon_interval =
2131 iwl3945_adjust_beacon_interval(
2132 le16_to_cpu(priv->rxon_timing.beacon_interval));
2135 priv->rxon_timing.atim_window = 0;
2137 priv->rxon_timing.beacon_interval =
2138 iwl3945_adjust_beacon_interval(conf->beacon_int);
2139 /* TODO: we need to get atim_window from upper stack
2140 * for now we set to 0 */
2141 priv->rxon_timing.atim_window = 0;
2145 (le16_to_cpu(priv->rxon_timing.beacon_interval) * 1024);
2146 result = do_div(tsf, interval_tm_unit);
2147 priv->rxon_timing.beacon_init_val =
2148 cpu_to_le32((u32) ((u64) interval_tm_unit - result));
2151 ("beacon interval %d beacon timer %d beacon tim %d\n",
2152 le16_to_cpu(priv->rxon_timing.beacon_interval),
2153 le32_to_cpu(priv->rxon_timing.beacon_init_val),
2154 le16_to_cpu(priv->rxon_timing.atim_window));
2157 static int iwl3945_scan_initiate(struct iwl3945_priv *priv)
2159 if (priv->iw_mode == NL80211_IFTYPE_AP) {
2160 IWL_ERROR("APs don't scan.\n");
2164 if (!iwl3945_is_ready_rf(priv)) {
2165 IWL_DEBUG_SCAN("Aborting scan due to not ready.\n");
2169 if (test_bit(STATUS_SCANNING, &priv->status)) {
2170 IWL_DEBUG_SCAN("Scan already in progress.\n");
2174 if (test_bit(STATUS_SCAN_ABORTING, &priv->status)) {
2175 IWL_DEBUG_SCAN("Scan request while abort pending. "
2180 IWL_DEBUG_INFO("Starting scan...\n");
2181 if (priv->cfg->sku & IWL_SKU_G)
2182 priv->scan_bands |= BIT(IEEE80211_BAND_2GHZ);
2183 if (priv->cfg->sku & IWL_SKU_A)
2184 priv->scan_bands |= BIT(IEEE80211_BAND_5GHZ);
2185 set_bit(STATUS_SCANNING, &priv->status);
2186 priv->scan_start = jiffies;
2187 priv->scan_pass_start = priv->scan_start;
2189 queue_work(priv->workqueue, &priv->request_scan);
2194 static int iwl3945_set_rxon_hwcrypto(struct iwl3945_priv *priv, int hw_decrypt)
2196 struct iwl3945_rxon_cmd *rxon = &priv->staging_rxon;
2199 rxon->filter_flags &= ~RXON_FILTER_DIS_DECRYPT_MSK;
2201 rxon->filter_flags |= RXON_FILTER_DIS_DECRYPT_MSK;
2206 static void iwl3945_set_flags_for_phymode(struct iwl3945_priv *priv,
2207 enum ieee80211_band band)
2209 if (band == IEEE80211_BAND_5GHZ) {
2210 priv->staging_rxon.flags &=
2211 ~(RXON_FLG_BAND_24G_MSK | RXON_FLG_AUTO_DETECT_MSK
2212 | RXON_FLG_CCK_MSK);
2213 priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
2215 /* Copied from iwl3945_bg_post_associate() */
2216 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_SLOT_TIME)
2217 priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
2219 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
2221 if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
2222 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
2224 priv->staging_rxon.flags |= RXON_FLG_BAND_24G_MSK;
2225 priv->staging_rxon.flags |= RXON_FLG_AUTO_DETECT_MSK;
2226 priv->staging_rxon.flags &= ~RXON_FLG_CCK_MSK;
2231 * initialize rxon structure with default values from eeprom
2233 static void iwl3945_connection_init_rx_config(struct iwl3945_priv *priv)
2235 const struct iwl3945_channel_info *ch_info;
2237 memset(&priv->staging_rxon, 0, sizeof(priv->staging_rxon));
2239 switch (priv->iw_mode) {
2240 case NL80211_IFTYPE_AP:
2241 priv->staging_rxon.dev_type = RXON_DEV_TYPE_AP;
2244 case NL80211_IFTYPE_STATION:
2245 priv->staging_rxon.dev_type = RXON_DEV_TYPE_ESS;
2246 priv->staging_rxon.filter_flags = RXON_FILTER_ACCEPT_GRP_MSK;
2249 case NL80211_IFTYPE_ADHOC:
2250 priv->staging_rxon.dev_type = RXON_DEV_TYPE_IBSS;
2251 priv->staging_rxon.flags = RXON_FLG_SHORT_PREAMBLE_MSK;
2252 priv->staging_rxon.filter_flags = RXON_FILTER_BCON_AWARE_MSK |
2253 RXON_FILTER_ACCEPT_GRP_MSK;
2256 case NL80211_IFTYPE_MONITOR:
2257 priv->staging_rxon.dev_type = RXON_DEV_TYPE_SNIFFER;
2258 priv->staging_rxon.filter_flags = RXON_FILTER_PROMISC_MSK |
2259 RXON_FILTER_CTL2HOST_MSK | RXON_FILTER_ACCEPT_GRP_MSK;
2262 IWL_ERROR("Unsupported interface type %d\n", priv->iw_mode);
2267 /* TODO: Figure out when short_preamble would be set and cache from
2269 if (!hw_to_local(priv->hw)->short_preamble)
2270 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
2272 priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
2275 ch_info = iwl3945_get_channel_info(priv, priv->band,
2276 le16_to_cpu(priv->active_rxon.channel));
2279 ch_info = &priv->channel_info[0];
2282 * in some case A channels are all non IBSS
2283 * in this case force B/G channel
2285 if ((priv->iw_mode == NL80211_IFTYPE_ADHOC) &&
2286 !(is_channel_ibss(ch_info)))
2287 ch_info = &priv->channel_info[0];
2289 priv->staging_rxon.channel = cpu_to_le16(ch_info->channel);
2290 if (is_channel_a_band(ch_info))
2291 priv->band = IEEE80211_BAND_5GHZ;
2293 priv->band = IEEE80211_BAND_2GHZ;
2295 iwl3945_set_flags_for_phymode(priv, priv->band);
2297 priv->staging_rxon.ofdm_basic_rates =
2298 (IWL_OFDM_RATES_MASK >> IWL_FIRST_OFDM_RATE) & 0xFF;
2299 priv->staging_rxon.cck_basic_rates =
2300 (IWL_CCK_RATES_MASK >> IWL_FIRST_CCK_RATE) & 0xF;
2303 static int iwl3945_set_mode(struct iwl3945_priv *priv, int mode)
2305 if (mode == NL80211_IFTYPE_ADHOC) {
2306 const struct iwl3945_channel_info *ch_info;
2308 ch_info = iwl3945_get_channel_info(priv,
2310 le16_to_cpu(priv->staging_rxon.channel));
2312 if (!ch_info || !is_channel_ibss(ch_info)) {
2313 IWL_ERROR("channel %d not IBSS channel\n",
2314 le16_to_cpu(priv->staging_rxon.channel));
2319 priv->iw_mode = mode;
2321 iwl3945_connection_init_rx_config(priv);
2322 memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
2324 iwl3945_clear_stations_table(priv);
2326 /* dont commit rxon if rf-kill is on*/
2327 if (!iwl3945_is_ready_rf(priv))
2330 cancel_delayed_work(&priv->scan_check);
2331 if (iwl3945_scan_cancel_timeout(priv, 100)) {
2332 IWL_WARNING("Aborted scan still in progress after 100ms\n");
2333 IWL_DEBUG_MAC80211("leaving - scan abort failed.\n");
2337 iwl3945_commit_rxon(priv);
2342 static void iwl3945_build_tx_cmd_hwcrypto(struct iwl3945_priv *priv,
2343 struct ieee80211_tx_info *info,
2344 struct iwl3945_cmd *cmd,
2345 struct sk_buff *skb_frag,
2348 struct iwl3945_hw_key *keyinfo =
2349 &priv->stations[info->control.hw_key->hw_key_idx].keyinfo;
2351 switch (keyinfo->alg) {
2353 cmd->cmd.tx.sec_ctl = TX_CMD_SEC_CCM;
2354 memcpy(cmd->cmd.tx.key, keyinfo->key, keyinfo->keylen);
2355 IWL_DEBUG_TX("tx_cmd with aes hwcrypto\n");
2360 cmd->cmd.tx.sec_ctl = TX_CMD_SEC_TKIP;
2363 memcpy(cmd->cmd.tx.tkip_mic.byte, skb_frag->tail - 8,
2366 memset(cmd->cmd.tx.tkip_mic.byte, 0, 8);
2371 cmd->cmd.tx.sec_ctl = TX_CMD_SEC_WEP |
2372 (info->control.hw_key->hw_key_idx & TX_CMD_SEC_MSK) << TX_CMD_SEC_SHIFT;
2374 if (keyinfo->keylen == 13)
2375 cmd->cmd.tx.sec_ctl |= TX_CMD_SEC_KEY128;
2377 memcpy(&cmd->cmd.tx.key[3], keyinfo->key, keyinfo->keylen);
2379 IWL_DEBUG_TX("Configuring packet for WEP encryption "
2380 "with key %d\n", info->control.hw_key->hw_key_idx);
2384 printk(KERN_ERR "Unknown encode alg %d\n", keyinfo->alg);
2390 * handle build REPLY_TX command notification.
2392 static void iwl3945_build_tx_cmd_basic(struct iwl3945_priv *priv,
2393 struct iwl3945_cmd *cmd,
2394 struct ieee80211_tx_info *info,
2395 struct ieee80211_hdr *hdr,
2396 int is_unicast, u8 std_id)
2398 __le16 fc = hdr->frame_control;
2399 __le32 tx_flags = cmd->cmd.tx.tx_flags;
2401 cmd->cmd.tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
2402 if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
2403 tx_flags |= TX_CMD_FLG_ACK_MSK;
2404 if (ieee80211_is_mgmt(fc))
2405 tx_flags |= TX_CMD_FLG_SEQ_CTL_MSK;
2406 if (ieee80211_is_probe_resp(fc) &&
2407 !(le16_to_cpu(hdr->seq_ctrl) & 0xf))
2408 tx_flags |= TX_CMD_FLG_TSF_MSK;
2410 tx_flags &= (~TX_CMD_FLG_ACK_MSK);
2411 tx_flags |= TX_CMD_FLG_SEQ_CTL_MSK;
2414 cmd->cmd.tx.sta_id = std_id;
2415 if (ieee80211_has_morefrags(fc))
2416 tx_flags |= TX_CMD_FLG_MORE_FRAG_MSK;
2418 if (ieee80211_is_data_qos(fc)) {
2419 u8 *qc = ieee80211_get_qos_ctl(hdr);
2420 cmd->cmd.tx.tid_tspec = qc[0] & 0xf;
2421 tx_flags &= ~TX_CMD_FLG_SEQ_CTL_MSK;
2423 tx_flags |= TX_CMD_FLG_SEQ_CTL_MSK;
2426 if (info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) {
2427 tx_flags |= TX_CMD_FLG_RTS_MSK;
2428 tx_flags &= ~TX_CMD_FLG_CTS_MSK;
2429 } else if (info->flags & IEEE80211_TX_CTL_USE_CTS_PROTECT) {
2430 tx_flags &= ~TX_CMD_FLG_RTS_MSK;
2431 tx_flags |= TX_CMD_FLG_CTS_MSK;
2434 if ((tx_flags & TX_CMD_FLG_RTS_MSK) || (tx_flags & TX_CMD_FLG_CTS_MSK))
2435 tx_flags |= TX_CMD_FLG_FULL_TXOP_PROT_MSK;
2437 tx_flags &= ~(TX_CMD_FLG_ANT_SEL_MSK);
2438 if (ieee80211_is_mgmt(fc)) {
2439 if (ieee80211_is_assoc_req(fc) || ieee80211_is_reassoc_req(fc))
2440 cmd->cmd.tx.timeout.pm_frame_timeout = cpu_to_le16(3);
2442 cmd->cmd.tx.timeout.pm_frame_timeout = cpu_to_le16(2);
2444 cmd->cmd.tx.timeout.pm_frame_timeout = 0;
2445 #ifdef CONFIG_IWL3945_LEDS
2446 priv->rxtxpackets += le16_to_cpu(cmd->cmd.tx.len);
2450 cmd->cmd.tx.driver_txop = 0;
2451 cmd->cmd.tx.tx_flags = tx_flags;
2452 cmd->cmd.tx.next_frame_len = 0;
2456 * iwl3945_get_sta_id - Find station's index within station table
2458 static int iwl3945_get_sta_id(struct iwl3945_priv *priv, struct ieee80211_hdr *hdr)
2461 u16 fc = le16_to_cpu(hdr->frame_control);
2463 /* If this frame is broadcast or management, use broadcast station id */
2464 if (((fc & IEEE80211_FCTL_FTYPE) != IEEE80211_FTYPE_DATA) ||
2465 is_multicast_ether_addr(hdr->addr1))
2466 return priv->hw_setting.bcast_sta_id;
2468 switch (priv->iw_mode) {
2470 /* If we are a client station in a BSS network, use the special
2471 * AP station entry (that's the only station we communicate with) */
2472 case NL80211_IFTYPE_STATION:
2475 /* If we are an AP, then find the station, or use BCAST */
2476 case NL80211_IFTYPE_AP:
2477 sta_id = iwl3945_hw_find_station(priv, hdr->addr1);
2478 if (sta_id != IWL_INVALID_STATION)
2480 return priv->hw_setting.bcast_sta_id;
2482 /* If this frame is going out to an IBSS network, find the station,
2483 * or create a new station table entry */
2484 case NL80211_IFTYPE_ADHOC: {
2485 DECLARE_MAC_BUF(mac);
2487 /* Create new station table entry */
2488 sta_id = iwl3945_hw_find_station(priv, hdr->addr1);
2489 if (sta_id != IWL_INVALID_STATION)
2492 sta_id = iwl3945_add_station(priv, hdr->addr1, 0, CMD_ASYNC);
2494 if (sta_id != IWL_INVALID_STATION)
2497 IWL_DEBUG_DROP("Station %s not in station map. "
2498 "Defaulting to broadcast...\n",
2499 print_mac(mac, hdr->addr1));
2500 iwl3945_print_hex_dump(IWL_DL_DROP, (u8 *) hdr, sizeof(*hdr));
2501 return priv->hw_setting.bcast_sta_id;
2503 /* If we are in monitor mode, use BCAST. This is required for
2504 * packet injection. */
2505 case NL80211_IFTYPE_MONITOR:
2506 return priv->hw_setting.bcast_sta_id;
2509 IWL_WARNING("Unknown mode of operation: %d\n", priv->iw_mode);
2510 return priv->hw_setting.bcast_sta_id;
2515 * start REPLY_TX command process
2517 static int iwl3945_tx_skb(struct iwl3945_priv *priv, struct sk_buff *skb)
2519 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
2520 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
2521 struct iwl3945_tfd_frame *tfd;
2523 int txq_id = skb_get_queue_mapping(skb);
2524 struct iwl3945_tx_queue *txq = NULL;
2525 struct iwl3945_queue *q = NULL;
2526 dma_addr_t phys_addr;
2527 dma_addr_t txcmd_phys;
2528 struct iwl3945_cmd *out_cmd = NULL;
2529 u16 len, idx, len_org, hdr_len;
2536 u8 wait_write_ptr = 0;
2538 unsigned long flags;
2541 spin_lock_irqsave(&priv->lock, flags);
2542 if (iwl3945_is_rfkill(priv)) {
2543 IWL_DEBUG_DROP("Dropping - RF KILL\n");
2547 if ((ieee80211_get_tx_rate(priv->hw, info)->hw_value & 0xFF) == IWL_INVALID_RATE) {
2548 IWL_ERROR("ERROR: No TX rate available.\n");
2552 unicast = !is_multicast_ether_addr(hdr->addr1);
2555 fc = hdr->frame_control;
2557 #ifdef CONFIG_IWL3945_DEBUG
2558 if (ieee80211_is_auth(fc))
2559 IWL_DEBUG_TX("Sending AUTH frame\n");
2560 else if (ieee80211_is_assoc_req(fc))
2561 IWL_DEBUG_TX("Sending ASSOC frame\n");
2562 else if (ieee80211_is_reassoc_req(fc))
2563 IWL_DEBUG_TX("Sending REASSOC frame\n");
2566 /* drop all data frame if we are not associated */
2567 if (ieee80211_is_data(fc) &&
2568 (priv->iw_mode != NL80211_IFTYPE_MONITOR) && /* packet injection */
2569 (!iwl3945_is_associated(priv) ||
2570 ((priv->iw_mode == NL80211_IFTYPE_STATION) && !priv->assoc_id))) {
2571 IWL_DEBUG_DROP("Dropping - !iwl3945_is_associated\n");
2575 spin_unlock_irqrestore(&priv->lock, flags);
2577 hdr_len = ieee80211_hdrlen(fc);
2579 /* Find (or create) index into station table for destination station */
2580 sta_id = iwl3945_get_sta_id(priv, hdr);
2581 if (sta_id == IWL_INVALID_STATION) {
2582 DECLARE_MAC_BUF(mac);
2584 IWL_DEBUG_DROP("Dropping - INVALID STATION: %s\n",
2585 print_mac(mac, hdr->addr1));
2589 IWL_DEBUG_RATE("station Id %d\n", sta_id);
2591 if (ieee80211_is_data_qos(fc)) {
2592 qc = ieee80211_get_qos_ctl(hdr);
2593 tid = qc[0] & IEEE80211_QOS_CTL_TID_MASK;
2594 seq_number = priv->stations[sta_id].tid[tid].seq_number &
2596 hdr->seq_ctrl = cpu_to_le16(seq_number) |
2598 __constant_cpu_to_le16(IEEE80211_SCTL_FRAG));
2602 /* Descriptor for chosen Tx queue */
2603 txq = &priv->txq[txq_id];
2606 spin_lock_irqsave(&priv->lock, flags);
2608 /* Set up first empty TFD within this queue's circular TFD buffer */
2609 tfd = &txq->bd[q->write_ptr];
2610 memset(tfd, 0, sizeof(*tfd));
2611 control_flags = (u32 *) tfd;
2612 idx = get_cmd_index(q, q->write_ptr, 0);
2614 /* Set up driver data for this TFD */
2615 memset(&(txq->txb[q->write_ptr]), 0, sizeof(struct iwl3945_tx_info));
2616 txq->txb[q->write_ptr].skb[0] = skb;
2618 /* Init first empty entry in queue's array of Tx/cmd buffers */
2619 out_cmd = &txq->cmd[idx];
2620 memset(&out_cmd->hdr, 0, sizeof(out_cmd->hdr));
2621 memset(&out_cmd->cmd.tx, 0, sizeof(out_cmd->cmd.tx));
2624 * Set up the Tx-command (not MAC!) header.
2625 * Store the chosen Tx queue and TFD index within the sequence field;
2626 * after Tx, uCode's Tx response will return this value so driver can
2627 * locate the frame within the tx queue and do post-tx processing.
2629 out_cmd->hdr.cmd = REPLY_TX;
2630 out_cmd->hdr.sequence = cpu_to_le16((u16)(QUEUE_TO_SEQ(txq_id) |
2631 INDEX_TO_SEQ(q->write_ptr)));
2633 /* Copy MAC header from skb into command buffer */
2634 memcpy(out_cmd->cmd.tx.hdr, hdr, hdr_len);
2637 * Use the first empty entry in this queue's command buffer array
2638 * to contain the Tx command and MAC header concatenated together
2639 * (payload data will be in another buffer).
2640 * Size of this varies, due to varying MAC header length.
2641 * If end is not dword aligned, we'll have 2 extra bytes at the end
2642 * of the MAC header (device reads on dword boundaries).
2643 * We'll tell device about this padding later.
2645 len = priv->hw_setting.tx_cmd_len +
2646 sizeof(struct iwl3945_cmd_header) + hdr_len;
2649 len = (len + 3) & ~3;
2656 /* Physical address of this Tx command's header (not MAC header!),
2657 * within command buffer array. */
2658 txcmd_phys = txq->dma_addr_cmd + sizeof(struct iwl3945_cmd) * idx +
2659 offsetof(struct iwl3945_cmd, hdr);
2661 /* Add buffer containing Tx command and MAC(!) header to TFD's
2663 iwl3945_hw_txq_attach_buf_to_tfd(priv, tfd, txcmd_phys, len);
2665 if (info->control.hw_key)
2666 iwl3945_build_tx_cmd_hwcrypto(priv, info, out_cmd, skb, 0);
2668 /* Set up TFD's 2nd entry to point directly to remainder of skb,
2669 * if any (802.11 null frames have no payload). */
2670 len = skb->len - hdr_len;
2672 phys_addr = pci_map_single(priv->pci_dev, skb->data + hdr_len,
2673 len, PCI_DMA_TODEVICE);
2674 iwl3945_hw_txq_attach_buf_to_tfd(priv, tfd, phys_addr, len);
2678 /* If there is no payload, then we use only one Tx buffer */
2679 *control_flags = TFD_CTL_COUNT_SET(1);
2681 /* Else use 2 buffers.
2682 * Tell 3945 about any padding after MAC header */
2683 *control_flags = TFD_CTL_COUNT_SET(2) |
2684 TFD_CTL_PAD_SET(U32_PAD(len));
2686 /* Total # bytes to be transmitted */
2687 len = (u16)skb->len;
2688 out_cmd->cmd.tx.len = cpu_to_le16(len);
2690 /* TODO need this for burst mode later on */
2691 iwl3945_build_tx_cmd_basic(priv, out_cmd, info, hdr, unicast, sta_id);
2693 /* set is_hcca to 0; it probably will never be implemented */
2694 iwl3945_hw_build_tx_cmd_rate(priv, out_cmd, info, hdr, sta_id, 0);
2696 out_cmd->cmd.tx.tx_flags &= ~TX_CMD_FLG_ANT_A_MSK;
2697 out_cmd->cmd.tx.tx_flags &= ~TX_CMD_FLG_ANT_B_MSK;
2699 if (!ieee80211_has_morefrags(hdr->frame_control)) {
2700 txq->need_update = 1;
2702 priv->stations[sta_id].tid[tid].seq_number = seq_number;
2705 txq->need_update = 0;
2708 iwl3945_print_hex_dump(IWL_DL_TX, out_cmd->cmd.payload,
2709 sizeof(out_cmd->cmd.tx));
2711 iwl3945_print_hex_dump(IWL_DL_TX, (u8 *)out_cmd->cmd.tx.hdr,
2712 ieee80211_hdrlen(fc));
2714 /* Tell device the write index *just past* this latest filled TFD */
2715 q->write_ptr = iwl_queue_inc_wrap(q->write_ptr, q->n_bd);
2716 rc = iwl3945_tx_queue_update_write_ptr(priv, txq);
2717 spin_unlock_irqrestore(&priv->lock, flags);
2722 if ((iwl3945_queue_space(q) < q->high_mark)
2723 && priv->mac80211_registered) {
2724 if (wait_write_ptr) {
2725 spin_lock_irqsave(&priv->lock, flags);
2726 txq->need_update = 1;
2727 iwl3945_tx_queue_update_write_ptr(priv, txq);
2728 spin_unlock_irqrestore(&priv->lock, flags);
2731 ieee80211_stop_queue(priv->hw, skb_get_queue_mapping(skb));
2737 spin_unlock_irqrestore(&priv->lock, flags);
2742 static void iwl3945_set_rate(struct iwl3945_priv *priv)
2744 const struct ieee80211_supported_band *sband = NULL;
2745 struct ieee80211_rate *rate;
2748 sband = iwl3945_get_band(priv, priv->band);
2750 IWL_ERROR("Failed to set rate: unable to get hw mode\n");
2754 priv->active_rate = 0;
2755 priv->active_rate_basic = 0;
2757 IWL_DEBUG_RATE("Setting rates for %s GHz\n",
2758 sband->band == IEEE80211_BAND_2GHZ ? "2.4" : "5");
2760 for (i = 0; i < sband->n_bitrates; i++) {
2761 rate = &sband->bitrates[i];
2762 if ((rate->hw_value < IWL_RATE_COUNT) &&
2763 !(rate->flags & IEEE80211_CHAN_DISABLED)) {
2764 IWL_DEBUG_RATE("Adding rate index %d (plcp %d)\n",
2765 rate->hw_value, iwl3945_rates[rate->hw_value].plcp);
2766 priv->active_rate |= (1 << rate->hw_value);
2770 IWL_DEBUG_RATE("Set active_rate = %0x, active_rate_basic = %0x\n",
2771 priv->active_rate, priv->active_rate_basic);
2774 * If a basic rate is configured, then use it (adding IWL_RATE_1M_MASK)
2775 * otherwise set it to the default of all CCK rates and 6, 12, 24 for
2778 if (priv->active_rate_basic & IWL_CCK_BASIC_RATES_MASK)
2779 priv->staging_rxon.cck_basic_rates =
2780 ((priv->active_rate_basic &
2781 IWL_CCK_RATES_MASK) >> IWL_FIRST_CCK_RATE) & 0xF;
2783 priv->staging_rxon.cck_basic_rates =
2784 (IWL_CCK_BASIC_RATES_MASK >> IWL_FIRST_CCK_RATE) & 0xF;
2786 if (priv->active_rate_basic & IWL_OFDM_BASIC_RATES_MASK)
2787 priv->staging_rxon.ofdm_basic_rates =
2788 ((priv->active_rate_basic &
2789 (IWL_OFDM_BASIC_RATES_MASK | IWL_RATE_6M_MASK)) >>
2790 IWL_FIRST_OFDM_RATE) & 0xFF;
2792 priv->staging_rxon.ofdm_basic_rates =
2793 (IWL_OFDM_BASIC_RATES_MASK >> IWL_FIRST_OFDM_RATE) & 0xFF;
2796 static void iwl3945_radio_kill_sw(struct iwl3945_priv *priv, int disable_radio)
2798 unsigned long flags;
2800 if (!!disable_radio == test_bit(STATUS_RF_KILL_SW, &priv->status))
2803 IWL_DEBUG_RF_KILL("Manual SW RF KILL set to: RADIO %s\n",
2804 disable_radio ? "OFF" : "ON");
2806 if (disable_radio) {
2807 iwl3945_scan_cancel(priv);
2808 /* FIXME: This is a workaround for AP */
2809 if (priv->iw_mode != NL80211_IFTYPE_AP) {
2810 spin_lock_irqsave(&priv->lock, flags);
2811 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_SET,
2812 CSR_UCODE_SW_BIT_RFKILL);
2813 spin_unlock_irqrestore(&priv->lock, flags);
2814 iwl3945_send_card_state(priv, CARD_STATE_CMD_DISABLE, 0);
2815 set_bit(STATUS_RF_KILL_SW, &priv->status);
2820 spin_lock_irqsave(&priv->lock, flags);
2821 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
2823 clear_bit(STATUS_RF_KILL_SW, &priv->status);
2824 spin_unlock_irqrestore(&priv->lock, flags);
2829 spin_lock_irqsave(&priv->lock, flags);
2830 iwl3945_read32(priv, CSR_UCODE_DRV_GP1);
2831 if (!iwl3945_grab_nic_access(priv))
2832 iwl3945_release_nic_access(priv);
2833 spin_unlock_irqrestore(&priv->lock, flags);
2835 if (test_bit(STATUS_RF_KILL_HW, &priv->status)) {
2836 IWL_DEBUG_RF_KILL("Can not turn radio back on - "
2837 "disabled by HW switch\n");
2842 queue_work(priv->workqueue, &priv->restart);
2846 void iwl3945_set_decrypted_flag(struct iwl3945_priv *priv, struct sk_buff *skb,
2847 u32 decrypt_res, struct ieee80211_rx_status *stats)
2850 le16_to_cpu(((struct ieee80211_hdr *)skb->data)->frame_control);
2852 if (priv->active_rxon.filter_flags & RXON_FILTER_DIS_DECRYPT_MSK)
2855 if (!(fc & IEEE80211_FCTL_PROTECTED))
2858 IWL_DEBUG_RX("decrypt_res:0x%x\n", decrypt_res);
2859 switch (decrypt_res & RX_RES_STATUS_SEC_TYPE_MSK) {
2860 case RX_RES_STATUS_SEC_TYPE_TKIP:
2861 if ((decrypt_res & RX_RES_STATUS_DECRYPT_TYPE_MSK) ==
2862 RX_RES_STATUS_BAD_ICV_MIC)
2863 stats->flag |= RX_FLAG_MMIC_ERROR;
2864 case RX_RES_STATUS_SEC_TYPE_WEP:
2865 case RX_RES_STATUS_SEC_TYPE_CCMP:
2866 if ((decrypt_res & RX_RES_STATUS_DECRYPT_TYPE_MSK) ==
2867 RX_RES_STATUS_DECRYPT_OK) {
2868 IWL_DEBUG_RX("hw decrypt successfully!!!\n");
2869 stats->flag |= RX_FLAG_DECRYPTED;
2878 #ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT
2880 #include "iwl-spectrum.h"
2882 #define BEACON_TIME_MASK_LOW 0x00FFFFFF
2883 #define BEACON_TIME_MASK_HIGH 0xFF000000
2884 #define TIME_UNIT 1024
2887 * extended beacon time format
2888 * time in usec will be changed into a 32-bit value in 8:24 format
2889 * the high 1 byte is the beacon counts
2890 * the lower 3 bytes is the time in usec within one beacon interval
2893 static u32 iwl3945_usecs_to_beacons(u32 usec, u32 beacon_interval)
2897 u32 interval = beacon_interval * 1024;
2899 if (!interval || !usec)
2902 quot = (usec / interval) & (BEACON_TIME_MASK_HIGH >> 24);
2903 rem = (usec % interval) & BEACON_TIME_MASK_LOW;
2905 return (quot << 24) + rem;
2908 /* base is usually what we get from ucode with each received frame,
2909 * the same as HW timer counter counting down
2912 static __le32 iwl3945_add_beacon_time(u32 base, u32 addon, u32 beacon_interval)
2914 u32 base_low = base & BEACON_TIME_MASK_LOW;
2915 u32 addon_low = addon & BEACON_TIME_MASK_LOW;
2916 u32 interval = beacon_interval * TIME_UNIT;
2917 u32 res = (base & BEACON_TIME_MASK_HIGH) +
2918 (addon & BEACON_TIME_MASK_HIGH);
2920 if (base_low > addon_low)
2921 res += base_low - addon_low;
2922 else if (base_low < addon_low) {
2923 res += interval + base_low - addon_low;
2928 return cpu_to_le32(res);
2931 static int iwl3945_get_measurement(struct iwl3945_priv *priv,
2932 struct ieee80211_measurement_params *params,
2935 struct iwl3945_spectrum_cmd spectrum;
2936 struct iwl3945_rx_packet *res;
2937 struct iwl3945_host_cmd cmd = {
2938 .id = REPLY_SPECTRUM_MEASUREMENT_CMD,
2939 .data = (void *)&spectrum,
2940 .meta.flags = CMD_WANT_SKB,
2942 u32 add_time = le64_to_cpu(params->start_time);
2944 int spectrum_resp_status;
2945 int duration = le16_to_cpu(params->duration);
2947 if (iwl3945_is_associated(priv))
2949 iwl3945_usecs_to_beacons(
2950 le64_to_cpu(params->start_time) - priv->last_tsf,
2951 le16_to_cpu(priv->rxon_timing.beacon_interval));
2953 memset(&spectrum, 0, sizeof(spectrum));
2955 spectrum.channel_count = cpu_to_le16(1);
2957 RXON_FLG_TSF2HOST_MSK | RXON_FLG_ANT_A_MSK | RXON_FLG_DIS_DIV_MSK;
2958 spectrum.filter_flags = MEASUREMENT_FILTER_FLAG;
2959 cmd.len = sizeof(spectrum);
2960 spectrum.len = cpu_to_le16(cmd.len - sizeof(spectrum.len));
2962 if (iwl3945_is_associated(priv))
2963 spectrum.start_time =
2964 iwl3945_add_beacon_time(priv->last_beacon_time,
2966 le16_to_cpu(priv->rxon_timing.beacon_interval));
2968 spectrum.start_time = 0;
2970 spectrum.channels[0].duration = cpu_to_le32(duration * TIME_UNIT);
2971 spectrum.channels[0].channel = params->channel;
2972 spectrum.channels[0].type = type;
2973 if (priv->active_rxon.flags & RXON_FLG_BAND_24G_MSK)
2974 spectrum.flags |= RXON_FLG_BAND_24G_MSK |
2975 RXON_FLG_AUTO_DETECT_MSK | RXON_FLG_TGG_PROTECT_MSK;
2977 rc = iwl3945_send_cmd_sync(priv, &cmd);
2981 res = (struct iwl3945_rx_packet *)cmd.meta.u.skb->data;
2982 if (res->hdr.flags & IWL_CMD_FAILED_MSK) {
2983 IWL_ERROR("Bad return from REPLY_RX_ON_ASSOC command\n");
2987 spectrum_resp_status = le16_to_cpu(res->u.spectrum.status);
2988 switch (spectrum_resp_status) {
2989 case 0: /* Command will be handled */
2990 if (res->u.spectrum.id != 0xff) {
2991 IWL_DEBUG_INFO("Replaced existing measurement: %d\n",
2992 res->u.spectrum.id);
2993 priv->measurement_status &= ~MEASUREMENT_READY;
2995 priv->measurement_status |= MEASUREMENT_ACTIVE;
2999 case 1: /* Command will not be handled */
3004 dev_kfree_skb_any(cmd.meta.u.skb);
3010 static void iwl3945_rx_reply_alive(struct iwl3945_priv *priv,
3011 struct iwl3945_rx_mem_buffer *rxb)
3013 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3014 struct iwl3945_alive_resp *palive;
3015 struct delayed_work *pwork;
3017 palive = &pkt->u.alive_frame;
3019 IWL_DEBUG_INFO("Alive ucode status 0x%08X revision "
3021 palive->is_valid, palive->ver_type,
3022 palive->ver_subtype);
3024 if (palive->ver_subtype == INITIALIZE_SUBTYPE) {
3025 IWL_DEBUG_INFO("Initialization Alive received.\n");
3026 memcpy(&priv->card_alive_init,
3027 &pkt->u.alive_frame,
3028 sizeof(struct iwl3945_init_alive_resp));
3029 pwork = &priv->init_alive_start;
3031 IWL_DEBUG_INFO("Runtime Alive received.\n");
3032 memcpy(&priv->card_alive, &pkt->u.alive_frame,
3033 sizeof(struct iwl3945_alive_resp));
3034 pwork = &priv->alive_start;
3035 iwl3945_disable_events(priv);
3038 /* We delay the ALIVE response by 5ms to
3039 * give the HW RF Kill time to activate... */
3040 if (palive->is_valid == UCODE_VALID_OK)
3041 queue_delayed_work(priv->workqueue, pwork,
3042 msecs_to_jiffies(5));
3044 IWL_WARNING("uCode did not respond OK.\n");
3047 static void iwl3945_rx_reply_add_sta(struct iwl3945_priv *priv,
3048 struct iwl3945_rx_mem_buffer *rxb)
3050 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3052 IWL_DEBUG_RX("Received REPLY_ADD_STA: 0x%02X\n", pkt->u.status);
3056 static void iwl3945_rx_reply_error(struct iwl3945_priv *priv,
3057 struct iwl3945_rx_mem_buffer *rxb)
3059 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3061 IWL_ERROR("Error Reply type 0x%08X cmd %s (0x%02X) "
3062 "seq 0x%04X ser 0x%08X\n",
3063 le32_to_cpu(pkt->u.err_resp.error_type),
3064 get_cmd_string(pkt->u.err_resp.cmd_id),
3065 pkt->u.err_resp.cmd_id,
3066 le16_to_cpu(pkt->u.err_resp.bad_cmd_seq_num),
3067 le32_to_cpu(pkt->u.err_resp.error_info));
3070 #define TX_STATUS_ENTRY(x) case TX_STATUS_FAIL_ ## x: return #x
3072 static void iwl3945_rx_csa(struct iwl3945_priv *priv, struct iwl3945_rx_mem_buffer *rxb)
3074 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3075 struct iwl3945_rxon_cmd *rxon = (void *)&priv->active_rxon;
3076 struct iwl3945_csa_notification *csa = &(pkt->u.csa_notif);
3077 IWL_DEBUG_11H("CSA notif: channel %d, status %d\n",
3078 le16_to_cpu(csa->channel), le32_to_cpu(csa->status));
3079 rxon->channel = csa->channel;
3080 priv->staging_rxon.channel = csa->channel;
3083 static void iwl3945_rx_spectrum_measure_notif(struct iwl3945_priv *priv,
3084 struct iwl3945_rx_mem_buffer *rxb)
3086 #ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT
3087 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3088 struct iwl3945_spectrum_notification *report = &(pkt->u.spectrum_notif);
3090 if (!report->state) {
3091 IWL_DEBUG(IWL_DL_11H | IWL_DL_INFO,
3092 "Spectrum Measure Notification: Start\n");
3096 memcpy(&priv->measure_report, report, sizeof(*report));
3097 priv->measurement_status |= MEASUREMENT_READY;
3101 static void iwl3945_rx_pm_sleep_notif(struct iwl3945_priv *priv,
3102 struct iwl3945_rx_mem_buffer *rxb)
3104 #ifdef CONFIG_IWL3945_DEBUG
3105 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3106 struct iwl3945_sleep_notification *sleep = &(pkt->u.sleep_notif);
3107 IWL_DEBUG_RX("sleep mode: %d, src: %d\n",
3108 sleep->pm_sleep_mode, sleep->pm_wakeup_src);
3112 static void iwl3945_rx_pm_debug_statistics_notif(struct iwl3945_priv *priv,
3113 struct iwl3945_rx_mem_buffer *rxb)
3115 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3116 IWL_DEBUG_RADIO("Dumping %d bytes of unhandled "
3117 "notification for %s:\n",
3118 le32_to_cpu(pkt->len), get_cmd_string(pkt->hdr.cmd));
3119 iwl3945_print_hex_dump(IWL_DL_RADIO, pkt->u.raw, le32_to_cpu(pkt->len));
3122 static void iwl3945_bg_beacon_update(struct work_struct *work)
3124 struct iwl3945_priv *priv =
3125 container_of(work, struct iwl3945_priv, beacon_update);
3126 struct sk_buff *beacon;
3128 /* Pull updated AP beacon from mac80211. will fail if not in AP mode */
3129 beacon = ieee80211_beacon_get(priv->hw, priv->vif);
3132 IWL_ERROR("update beacon failed\n");
3136 mutex_lock(&priv->mutex);
3137 /* new beacon skb is allocated every time; dispose previous.*/
3138 if (priv->ibss_beacon)
3139 dev_kfree_skb(priv->ibss_beacon);
3141 priv->ibss_beacon = beacon;
3142 mutex_unlock(&priv->mutex);
3144 iwl3945_send_beacon_cmd(priv);
3147 static void iwl3945_rx_beacon_notif(struct iwl3945_priv *priv,
3148 struct iwl3945_rx_mem_buffer *rxb)
3150 #ifdef CONFIG_IWL3945_DEBUG
3151 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3152 struct iwl3945_beacon_notif *beacon = &(pkt->u.beacon_status);
3153 u8 rate = beacon->beacon_notify_hdr.rate;
3155 IWL_DEBUG_RX("beacon status %x retries %d iss %d "
3156 "tsf %d %d rate %d\n",
3157 le32_to_cpu(beacon->beacon_notify_hdr.status) & TX_STATUS_MSK,
3158 beacon->beacon_notify_hdr.failure_frame,
3159 le32_to_cpu(beacon->ibss_mgr_status),
3160 le32_to_cpu(beacon->high_tsf),
3161 le32_to_cpu(beacon->low_tsf), rate);
3164 if ((priv->iw_mode == NL80211_IFTYPE_AP) &&
3165 (!test_bit(STATUS_EXIT_PENDING, &priv->status)))
3166 queue_work(priv->workqueue, &priv->beacon_update);
3169 /* Service response to REPLY_SCAN_CMD (0x80) */
3170 static void iwl3945_rx_reply_scan(struct iwl3945_priv *priv,
3171 struct iwl3945_rx_mem_buffer *rxb)
3173 #ifdef CONFIG_IWL3945_DEBUG
3174 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3175 struct iwl3945_scanreq_notification *notif =
3176 (struct iwl3945_scanreq_notification *)pkt->u.raw;
3178 IWL_DEBUG_RX("Scan request status = 0x%x\n", notif->status);
3182 /* Service SCAN_START_NOTIFICATION (0x82) */
3183 static void iwl3945_rx_scan_start_notif(struct iwl3945_priv *priv,
3184 struct iwl3945_rx_mem_buffer *rxb)
3186 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3187 struct iwl3945_scanstart_notification *notif =
3188 (struct iwl3945_scanstart_notification *)pkt->u.raw;
3189 priv->scan_start_tsf = le32_to_cpu(notif->tsf_low);
3190 IWL_DEBUG_SCAN("Scan start: "
3192 "(TSF: 0x%08X:%08X) - %d (beacon timer %u)\n",
3194 notif->band ? "bg" : "a",
3196 notif->tsf_low, notif->status, notif->beacon_timer);
3199 /* Service SCAN_RESULTS_NOTIFICATION (0x83) */
3200 static void iwl3945_rx_scan_results_notif(struct iwl3945_priv *priv,
3201 struct iwl3945_rx_mem_buffer *rxb)
3203 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3204 struct iwl3945_scanresults_notification *notif =
3205 (struct iwl3945_scanresults_notification *)pkt->u.raw;
3207 IWL_DEBUG_SCAN("Scan ch.res: "
3209 "(TSF: 0x%08X:%08X) - %d "
3210 "elapsed=%lu usec (%dms since last)\n",
3212 notif->band ? "bg" : "a",
3213 le32_to_cpu(notif->tsf_high),
3214 le32_to_cpu(notif->tsf_low),
3215 le32_to_cpu(notif->statistics[0]),
3216 le32_to_cpu(notif->tsf_low) - priv->scan_start_tsf,
3217 jiffies_to_msecs(elapsed_jiffies
3218 (priv->last_scan_jiffies, jiffies)));
3220 priv->last_scan_jiffies = jiffies;
3221 priv->next_scan_jiffies = 0;
3224 /* Service SCAN_COMPLETE_NOTIFICATION (0x84) */
3225 static void iwl3945_rx_scan_complete_notif(struct iwl3945_priv *priv,
3226 struct iwl3945_rx_mem_buffer *rxb)
3228 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3229 struct iwl3945_scancomplete_notification *scan_notif = (void *)pkt->u.raw;
3231 IWL_DEBUG_SCAN("Scan complete: %d channels (TSF 0x%08X:%08X) - %d\n",
3232 scan_notif->scanned_channels,
3233 scan_notif->tsf_low,
3234 scan_notif->tsf_high, scan_notif->status);
3236 /* The HW is no longer scanning */
3237 clear_bit(STATUS_SCAN_HW, &priv->status);
3239 /* The scan completion notification came in, so kill that timer... */
3240 cancel_delayed_work(&priv->scan_check);
3242 IWL_DEBUG_INFO("Scan pass on %sGHz took %dms\n",
3243 (priv->scan_bands & BIT(IEEE80211_BAND_2GHZ)) ?
3245 jiffies_to_msecs(elapsed_jiffies
3246 (priv->scan_pass_start, jiffies)));
3248 /* Remove this scanned band from the list of pending
3249 * bands to scan, band G precedes A in order of scanning
3250 * as seen in iwl3945_bg_request_scan */
3251 if (priv->scan_bands & BIT(IEEE80211_BAND_2GHZ))
3252 priv->scan_bands &= ~BIT(IEEE80211_BAND_2GHZ);
3253 else if (priv->scan_bands & BIT(IEEE80211_BAND_5GHZ))
3254 priv->scan_bands &= ~BIT(IEEE80211_BAND_5GHZ);
3256 /* If a request to abort was given, or the scan did not succeed
3257 * then we reset the scan state machine and terminate,
3258 * re-queuing another scan if one has been requested */
3259 if (test_bit(STATUS_SCAN_ABORTING, &priv->status)) {
3260 IWL_DEBUG_INFO("Aborted scan completed.\n");
3261 clear_bit(STATUS_SCAN_ABORTING, &priv->status);
3263 /* If there are more bands on this scan pass reschedule */
3264 if (priv->scan_bands > 0)
3268 priv->last_scan_jiffies = jiffies;
3269 priv->next_scan_jiffies = 0;
3270 IWL_DEBUG_INFO("Setting scan to off\n");
3272 clear_bit(STATUS_SCANNING, &priv->status);
3274 IWL_DEBUG_INFO("Scan took %dms\n",
3275 jiffies_to_msecs(elapsed_jiffies(priv->scan_start, jiffies)));
3277 queue_work(priv->workqueue, &priv->scan_completed);
3282 priv->scan_pass_start = jiffies;
3283 queue_work(priv->workqueue, &priv->request_scan);
3286 /* Handle notification from uCode that card's power state is changing
3287 * due to software, hardware, or critical temperature RFKILL */
3288 static void iwl3945_rx_card_state_notif(struct iwl3945_priv *priv,
3289 struct iwl3945_rx_mem_buffer *rxb)
3291 struct iwl3945_rx_packet *pkt = (void *)rxb->skb->data;
3292 u32 flags = le32_to_cpu(pkt->u.card_state_notif.flags);
3293 unsigned long status = priv->status;
3295 IWL_DEBUG_RF_KILL("Card state received: HW:%s SW:%s\n",
3296 (flags & HW_CARD_DISABLED) ? "Kill" : "On",
3297 (flags & SW_CARD_DISABLED) ? "Kill" : "On");
3299 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_SET,
3300 CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
3302 if (flags & HW_CARD_DISABLED)
3303 set_bit(STATUS_RF_KILL_HW, &priv->status);
3305 clear_bit(STATUS_RF_KILL_HW, &priv->status);
3308 if (flags & SW_CARD_DISABLED)
3309 set_bit(STATUS_RF_KILL_SW, &priv->status);
3311 clear_bit(STATUS_RF_KILL_SW, &priv->status);
3313 iwl3945_scan_cancel(priv);
3315 if ((test_bit(STATUS_RF_KILL_HW, &status) !=
3316 test_bit(STATUS_RF_KILL_HW, &priv->status)) ||
3317 (test_bit(STATUS_RF_KILL_SW, &status) !=
3318 test_bit(STATUS_RF_KILL_SW, &priv->status)))
3319 queue_work(priv->workqueue, &priv->rf_kill);
3321 wake_up_interruptible(&priv->wait_command_queue);
3325 * iwl3945_setup_rx_handlers - Initialize Rx handler callbacks
3327 * Setup the RX handlers for each of the reply types sent from the uCode
3330 * This function chains into the hardware specific files for them to setup
3331 * any hardware specific handlers as well.
3333 static void iwl3945_setup_rx_handlers(struct iwl3945_priv *priv)
3335 priv->rx_handlers[REPLY_ALIVE] = iwl3945_rx_reply_alive;
3336 priv->rx_handlers[REPLY_ADD_STA] = iwl3945_rx_reply_add_sta;
3337 priv->rx_handlers[REPLY_ERROR] = iwl3945_rx_reply_error;
3338 priv->rx_handlers[CHANNEL_SWITCH_NOTIFICATION] = iwl3945_rx_csa;
3339 priv->rx_handlers[SPECTRUM_MEASURE_NOTIFICATION] =
3340 iwl3945_rx_spectrum_measure_notif;
3341 priv->rx_handlers[PM_SLEEP_NOTIFICATION] = iwl3945_rx_pm_sleep_notif;
3342 priv->rx_handlers[PM_DEBUG_STATISTIC_NOTIFIC] =
3343 iwl3945_rx_pm_debug_statistics_notif;
3344 priv->rx_handlers[BEACON_NOTIFICATION] = iwl3945_rx_beacon_notif;
3347 * The same handler is used for both the REPLY to a discrete
3348 * statistics request from the host as well as for the periodic
3349 * statistics notifications (after received beacons) from the uCode.
3351 priv->rx_handlers[REPLY_STATISTICS_CMD] = iwl3945_hw_rx_statistics;
3352 priv->rx_handlers[STATISTICS_NOTIFICATION] = iwl3945_hw_rx_statistics;
3354 priv->rx_handlers[REPLY_SCAN_CMD] = iwl3945_rx_reply_scan;
3355 priv->rx_handlers[SCAN_START_NOTIFICATION] = iwl3945_rx_scan_start_notif;
3356 priv->rx_handlers[SCAN_RESULTS_NOTIFICATION] =
3357 iwl3945_rx_scan_results_notif;
3358 priv->rx_handlers[SCAN_COMPLETE_NOTIFICATION] =
3359 iwl3945_rx_scan_complete_notif;
3360 priv->rx_handlers[CARD_STATE_NOTIFICATION] = iwl3945_rx_card_state_notif;
3362 /* Set up hardware specific Rx handlers */
3363 iwl3945_hw_rx_handler_setup(priv);
3367 * iwl3945_cmd_queue_reclaim - Reclaim CMD queue entries
3368 * When FW advances 'R' index, all entries between old and new 'R' index
3369 * need to be reclaimed.
3371 static void iwl3945_cmd_queue_reclaim(struct iwl3945_priv *priv,
3372 int txq_id, int index)
3374 struct iwl3945_tx_queue *txq = &priv->txq[txq_id];
3375 struct iwl3945_queue *q = &txq->q;
3378 if ((index >= q->n_bd) || (iwl3945_x2_queue_used(q, index) == 0)) {
3379 IWL_ERROR("Read index for DMA queue txq id (%d), index %d, "
3380 "is out of range [0-%d] %d %d.\n", txq_id,
3381 index, q->n_bd, q->write_ptr, q->read_ptr);
3385 for (index = iwl_queue_inc_wrap(index, q->n_bd); q->read_ptr != index;
3386 q->read_ptr = iwl_queue_inc_wrap(q->read_ptr, q->n_bd)) {
3388 IWL_ERROR("HCMD skipped: index (%d) %d %d\n", index,
3389 q->write_ptr, q->read_ptr);
3390 queue_work(priv->workqueue, &priv->restart);
3399 * iwl3945_tx_cmd_complete - Pull unused buffers off the queue and reclaim them
3400 * @rxb: Rx buffer to reclaim
3402 * If an Rx buffer has an async callback associated with it the callback
3403 * will be executed. The attached skb (if present) will only be freed
3404 * if the callback returns 1
3406 static void iwl3945_tx_cmd_complete(struct iwl3945_priv *priv,
3407 struct iwl3945_rx_mem_buffer *rxb)
3409 struct iwl3945_rx_packet *pkt = (struct iwl3945_rx_packet *)rxb->skb->data;
3410 u16 sequence = le16_to_cpu(pkt->hdr.sequence);
3411 int txq_id = SEQ_TO_QUEUE(sequence);
3412 int index = SEQ_TO_INDEX(sequence);
3413 int huge = sequence & SEQ_HUGE_FRAME;
3415 struct iwl3945_cmd *cmd;
3417 BUG_ON(txq_id != IWL_CMD_QUEUE_NUM);
3419 cmd_index = get_cmd_index(&priv->txq[IWL_CMD_QUEUE_NUM].q, index, huge);
3420 cmd = &priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_index];
3422 /* Input error checking is done when commands are added to queue. */
3423 if (cmd->meta.flags & CMD_WANT_SKB) {
3424 cmd->meta.source->u.skb = rxb->skb;
3426 } else if (cmd->meta.u.callback &&
3427 !cmd->meta.u.callback(priv, cmd, rxb->skb))
3430 iwl3945_cmd_queue_reclaim(priv, txq_id, index);
3432 if (!(cmd->meta.flags & CMD_ASYNC)) {
3433 clear_bit(STATUS_HCMD_ACTIVE, &priv->status);
3434 wake_up_interruptible(&priv->wait_command_queue);
3438 /************************** RX-FUNCTIONS ****************************/
3440 * Rx theory of operation
3442 * The host allocates 32 DMA target addresses and passes the host address
3443 * to the firmware at register IWL_RFDS_TABLE_LOWER + N * RFD_SIZE where N is
3447 * The host/firmware share two index registers for managing the Rx buffers.
3449 * The READ index maps to the first position that the firmware may be writing
3450 * to -- the driver can read up to (but not including) this position and get
3452 * The READ index is managed by the firmware once the card is enabled.
3454 * The WRITE index maps to the last position the driver has read from -- the
3455 * position preceding WRITE is the last slot the firmware can place a packet.
3457 * The queue is empty (no good data) if WRITE = READ - 1, and is full if
3460 * During initialization, the host sets up the READ queue position to the first
3461 * INDEX position, and WRITE to the last (READ - 1 wrapped)
3463 * When the firmware places a packet in a buffer, it will advance the READ index
3464 * and fire the RX interrupt. The driver can then query the READ index and
3465 * process as many packets as possible, moving the WRITE index forward as it
3466 * resets the Rx queue buffers with new memory.
3468 * The management in the driver is as follows:
3469 * + A list of pre-allocated SKBs is stored in iwl->rxq->rx_free. When
3470 * iwl->rxq->free_count drops to or below RX_LOW_WATERMARK, work is scheduled
3471 * to replenish the iwl->rxq->rx_free.
3472 * + In iwl3945_rx_replenish (scheduled) if 'processed' != 'read' then the
3473 * iwl->rxq is replenished and the READ INDEX is updated (updating the
3474 * 'processed' and 'read' driver indexes as well)
3475 * + A received packet is processed and handed to the kernel network stack,
3476 * detached from the iwl->rxq. The driver 'processed' index is updated.
3477 * + The Host/Firmware iwl->rxq is replenished at tasklet time from the rx_free
3478 * list. If there are no allocated buffers in iwl->rxq->rx_free, the READ
3479 * INDEX is not incremented and iwl->status(RX_STALLED) is set. If there
3480 * were enough free buffers and RX_STALLED is set it is cleared.
3485 * iwl3945_rx_queue_alloc() Allocates rx_free
3486 * iwl3945_rx_replenish() Replenishes rx_free list from rx_used, and calls
3487 * iwl3945_rx_queue_restock
3488 * iwl3945_rx_queue_restock() Moves available buffers from rx_free into Rx
3489 * queue, updates firmware pointers, and updates
3490 * the WRITE index. If insufficient rx_free buffers
3491 * are available, schedules iwl3945_rx_replenish
3493 * -- enable interrupts --
3494 * ISR - iwl3945_rx() Detach iwl3945_rx_mem_buffers from pool up to the
3495 * READ INDEX, detaching the SKB from the pool.
3496 * Moves the packet buffer from queue to rx_used.
3497 * Calls iwl3945_rx_queue_restock to refill any empty
3504 * iwl3945_rx_queue_space - Return number of free slots available in queue.
3506 static int iwl3945_rx_queue_space(const struct iwl3945_rx_queue *q)
3508 int s = q->read - q->write;
3511 /* keep some buffer to not confuse full and empty queue */
3519 * iwl3945_rx_queue_update_write_ptr - Update the write pointer for the RX queue
3521 int iwl3945_rx_queue_update_write_ptr(struct iwl3945_priv *priv, struct iwl3945_rx_queue *q)
3525 unsigned long flags;
3527 spin_lock_irqsave(&q->lock, flags);
3529 if (q->need_update == 0)
3532 /* If power-saving is in use, make sure device is awake */
3533 if (test_bit(STATUS_POWER_PMI, &priv->status)) {
3534 reg = iwl3945_read32(priv, CSR_UCODE_DRV_GP1);
3536 if (reg & CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP) {
3537 iwl3945_set_bit(priv, CSR_GP_CNTRL,
3538 CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
3542 rc = iwl3945_grab_nic_access(priv);
3546 /* Device expects a multiple of 8 */
3547 iwl3945_write_direct32(priv, FH_RSCSR_CHNL0_WPTR,
3549 iwl3945_release_nic_access(priv);
3551 /* Else device is assumed to be awake */
3553 /* Device expects a multiple of 8 */
3554 iwl3945_write32(priv, FH_RSCSR_CHNL0_WPTR, q->write & ~0x7);
3560 spin_unlock_irqrestore(&q->lock, flags);
3565 * iwl3945_dma_addr2rbd_ptr - convert a DMA address to a uCode read buffer ptr
3567 static inline __le32 iwl3945_dma_addr2rbd_ptr(struct iwl3945_priv *priv,
3568 dma_addr_t dma_addr)
3570 return cpu_to_le32((u32)dma_addr);
3574 * iwl3945_rx_queue_restock - refill RX queue from pre-allocated pool
3576 * If there are slots in the RX queue that need to be restocked,
3577 * and we have free pre-allocated buffers, fill the ranks as much
3578 * as we can, pulling from rx_free.
3580 * This moves the 'write' index forward to catch up with 'processed', and
3581 * also updates the memory address in the firmware to reference the new
3584 static int iwl3945_rx_queue_restock(struct iwl3945_priv *priv)
3586 struct iwl3945_rx_queue *rxq = &priv->rxq;
3587 struct list_head *element;
3588 struct iwl3945_rx_mem_buffer *rxb;
3589 unsigned long flags;
3592 spin_lock_irqsave(&rxq->lock, flags);
3593 write = rxq->write & ~0x7;
3594 while ((iwl3945_rx_queue_space(rxq) > 0) && (rxq->free_count)) {
3595 /* Get next free Rx buffer, remove from free list */
3596 element = rxq->rx_free.next;
3597 rxb = list_entry(element, struct iwl3945_rx_mem_buffer, list);
3600 /* Point to Rx buffer via next RBD in circular buffer */
3601 rxq->bd[rxq->write] = iwl3945_dma_addr2rbd_ptr(priv, rxb->dma_addr);
3602 rxq->queue[rxq->write] = rxb;
3603 rxq->write = (rxq->write + 1) & RX_QUEUE_MASK;
3606 spin_unlock_irqrestore(&rxq->lock, flags);
3607 /* If the pre-allocated buffer pool is dropping low, schedule to
3609 if (rxq->free_count <= RX_LOW_WATERMARK)
3610 queue_work(priv->workqueue, &priv->rx_replenish);
3613 /* If we've added more space for the firmware to place data, tell it.
3614 * Increment device's write pointer in multiples of 8. */
3615 if ((write != (rxq->write & ~0x7))
3616 || (abs(rxq->write - rxq->read) > 7)) {
3617 spin_lock_irqsave(&rxq->lock, flags);
3618 rxq->need_update = 1;
3619 spin_unlock_irqrestore(&rxq->lock, flags);
3620 rc = iwl3945_rx_queue_update_write_ptr(priv, rxq);
3629 * iwl3945_rx_replenish - Move all used packet from rx_used to rx_free
3631 * When moving to rx_free an SKB is allocated for the slot.
3633 * Also restock the Rx queue via iwl3945_rx_queue_restock.
3634 * This is called as a scheduled work item (except for during initialization)
3636 static void iwl3945_rx_allocate(struct iwl3945_priv *priv)
3638 struct iwl3945_rx_queue *rxq = &priv->rxq;
3639 struct list_head *element;
3640 struct iwl3945_rx_mem_buffer *rxb;
3641 unsigned long flags;
3642 spin_lock_irqsave(&rxq->lock, flags);
3643 while (!list_empty(&rxq->rx_used)) {
3644 element = rxq->rx_used.next;
3645 rxb = list_entry(element, struct iwl3945_rx_mem_buffer, list);
3647 /* Alloc a new receive buffer */
3649 alloc_skb(IWL_RX_BUF_SIZE, __GFP_NOWARN | GFP_ATOMIC);
3651 if (net_ratelimit())
3652 printk(KERN_CRIT DRV_NAME
3653 ": Can not allocate SKB buffers\n");
3654 /* We don't reschedule replenish work here -- we will
3655 * call the restock method and if it still needs
3656 * more buffers it will schedule replenish */
3660 /* If radiotap head is required, reserve some headroom here.
3661 * The physical head count is a variable rx_stats->phy_count.
3662 * We reserve 4 bytes here. Plus these extra bytes, the
3663 * headroom of the physical head should be enough for the
3664 * radiotap head that iwl3945 supported. See iwl3945_rt.
3666 skb_reserve(rxb->skb, 4);
3668 priv->alloc_rxb_skb++;
3671 /* Get physical address of RB/SKB */
3673 pci_map_single(priv->pci_dev, rxb->skb->data,
3674 IWL_RX_BUF_SIZE, PCI_DMA_FROMDEVICE);
3675 list_add_tail(&rxb->list, &rxq->rx_free);
3678 spin_unlock_irqrestore(&rxq->lock, flags);
3682 * this should be called while priv->lock is locked
3684 static void __iwl3945_rx_replenish(void *data)
3686 struct iwl3945_priv *priv = data;
3688 iwl3945_rx_allocate(priv);
3689 iwl3945_rx_queue_restock(priv);
3693 void iwl3945_rx_replenish(void *data)
3695 struct iwl3945_priv *priv = data;
3696 unsigned long flags;
3698 iwl3945_rx_allocate(priv);
3700 spin_lock_irqsave(&priv->lock, flags);
3701 iwl3945_rx_queue_restock(priv);
3702 spin_unlock_irqrestore(&priv->lock, flags);
3705 /* Assumes that the skb field of the buffers in 'pool' is kept accurate.
3706 * If an SKB has been detached, the POOL needs to have its SKB set to NULL
3707 * This free routine walks the list of POOL entries and if SKB is set to
3708 * non NULL it is unmapped and freed
3710 static void iwl3945_rx_queue_free(struct iwl3945_priv *priv, struct iwl3945_rx_queue *rxq)
3713 for (i = 0; i < RX_QUEUE_SIZE + RX_FREE_BUFFERS; i++) {
3714 if (rxq->pool[i].skb != NULL) {
3715 pci_unmap_single(priv->pci_dev,
3716 rxq->pool[i].dma_addr,
3717 IWL_RX_BUF_SIZE, PCI_DMA_FROMDEVICE);
3718 dev_kfree_skb(rxq->pool[i].skb);
3722 pci_free_consistent(priv->pci_dev, 4 * RX_QUEUE_SIZE, rxq->bd,
3727 int iwl3945_rx_queue_alloc(struct iwl3945_priv *priv)
3729 struct iwl3945_rx_queue *rxq = &priv->rxq;
3730 struct pci_dev *dev = priv->pci_dev;
3733 spin_lock_init(&rxq->lock);
3734 INIT_LIST_HEAD(&rxq->rx_free);
3735 INIT_LIST_HEAD(&rxq->rx_used);
3737 /* Alloc the circular buffer of Read Buffer Descriptors (RBDs) */
3738 rxq->bd = pci_alloc_consistent(dev, 4 * RX_QUEUE_SIZE, &rxq->dma_addr);
3742 /* Fill the rx_used queue with _all_ of the Rx buffers */
3743 for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++)
3744 list_add_tail(&rxq->pool[i].list, &rxq->rx_used);
3746 /* Set us so that we have processed and used all buffers, but have
3747 * not restocked the Rx queue with fresh buffers */
3748 rxq->read = rxq->write = 0;
3749 rxq->free_count = 0;
3750 rxq->need_update = 0;
3754 void iwl3945_rx_queue_reset(struct iwl3945_priv *priv, struct iwl3945_rx_queue *rxq)
3756 unsigned long flags;
3758 spin_lock_irqsave(&rxq->lock, flags);
3759 INIT_LIST_HEAD(&rxq->rx_free);
3760 INIT_LIST_HEAD(&rxq->rx_used);
3761 /* Fill the rx_used queue with _all_ of the Rx buffers */
3762 for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++) {
3763 /* In the reset function, these buffers may have been allocated
3764 * to an SKB, so we need to unmap and free potential storage */
3765 if (rxq->pool[i].skb != NULL) {
3766 pci_unmap_single(priv->pci_dev,
3767 rxq->pool[i].dma_addr,
3768 IWL_RX_BUF_SIZE, PCI_DMA_FROMDEVICE);
3769 priv->alloc_rxb_skb--;
3770 dev_kfree_skb(rxq->pool[i].skb);
3771 rxq->pool[i].skb = NULL;
3773 list_add_tail(&rxq->pool[i].list, &rxq->rx_used);
3776 /* Set us so that we have processed and used all buffers, but have
3777 * not restocked the Rx queue with fresh buffers */
3778 rxq->read = rxq->write = 0;
3779 rxq->free_count = 0;
3780 spin_unlock_irqrestore(&rxq->lock, flags);
3783 /* Convert linear signal-to-noise ratio into dB */
3784 static u8 ratio2dB[100] = {
3785 /* 0 1 2 3 4 5 6 7 8 9 */
3786 0, 0, 6, 10, 12, 14, 16, 17, 18, 19, /* 00 - 09 */
3787 20, 21, 22, 22, 23, 23, 24, 25, 26, 26, /* 10 - 19 */
3788 26, 26, 26, 27, 27, 28, 28, 28, 29, 29, /* 20 - 29 */
3789 29, 30, 30, 30, 31, 31, 31, 31, 32, 32, /* 30 - 39 */
3790 32, 32, 32, 33, 33, 33, 33, 33, 34, 34, /* 40 - 49 */
3791 34, 34, 34, 34, 35, 35, 35, 35, 35, 35, /* 50 - 59 */
3792 36, 36, 36, 36, 36, 36, 36, 37, 37, 37, /* 60 - 69 */
3793 37, 37, 37, 37, 37, 38, 38, 38, 38, 38, /* 70 - 79 */
3794 38, 38, 38, 38, 38, 39, 39, 39, 39, 39, /* 80 - 89 */
3795 39, 39, 39, 39, 39, 40, 40, 40, 40, 40 /* 90 - 99 */
3798 /* Calculates a relative dB value from a ratio of linear
3799 * (i.e. not dB) signal levels.
3800 * Conversion assumes that levels are voltages (20*log), not powers (10*log). */
3801 int iwl3945_calc_db_from_ratio(int sig_ratio)
3803 /* 1000:1 or higher just report as 60 dB */
3804 if (sig_ratio >= 1000)
3807 /* 100:1 or higher, divide by 10 and use table,
3808 * add 20 dB to make up for divide by 10 */
3809 if (sig_ratio >= 100)
3810 return 20 + (int)ratio2dB[sig_ratio/10];
3812 /* We shouldn't see this */
3816 /* Use table for ratios 1:1 - 99:1 */
3817 return (int)ratio2dB[sig_ratio];
3820 #define PERFECT_RSSI (-20) /* dBm */
3821 #define WORST_RSSI (-95) /* dBm */
3822 #define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI)
3824 /* Calculate an indication of rx signal quality (a percentage, not dBm!).
3825 * See http://www.ces.clemson.edu/linux/signal_quality.shtml for info
3826 * about formulas used below. */
3827 int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm)
3830 int degradation = PERFECT_RSSI - rssi_dbm;
3832 /* If we get a noise measurement, use signal-to-noise ratio (SNR)
3833 * as indicator; formula is (signal dbm - noise dbm).
3834 * SNR at or above 40 is a great signal (100%).
3835 * Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator.
3836 * Weakest usable signal is usually 10 - 15 dB SNR. */
3838 if (rssi_dbm - noise_dbm >= 40)
3840 else if (rssi_dbm < noise_dbm)
3842 sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2;
3844 /* Else use just the signal level.
3845 * This formula is a least squares fit of data points collected and
3846 * compared with a reference system that had a percentage (%) display
3847 * for signal quality. */
3849 sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation *
3850 (15 * RSSI_RANGE + 62 * degradation)) /
3851 (RSSI_RANGE * RSSI_RANGE);
3855 else if (sig_qual < 1)
3862 * iwl3945_rx_handle - Main entry function for receiving responses from uCode
3864 * Uses the priv->rx_handlers callback function array to invoke
3865 * the appropriate handlers, including command responses,
3866 * frame-received notifications, and other notifications.
3868 static void iwl3945_rx_handle(struct iwl3945_priv *priv)
3870 struct iwl3945_rx_mem_buffer *rxb;
3871 struct iwl3945_rx_packet *pkt;
3872 struct iwl3945_rx_queue *rxq = &priv->rxq;
3875 unsigned long flags;
3879 /* uCode's read index (stored in shared DRAM) indicates the last Rx
3880 * buffer that the driver may process (last buffer filled by ucode). */
3881 r = iwl3945_hw_get_rx_read(priv);
3884 if (iwl3945_rx_queue_space(rxq) > (RX_QUEUE_SIZE / 2))
3886 /* Rx interrupt, but nothing sent from uCode */
3888 IWL_DEBUG(IWL_DL_RX | IWL_DL_ISR, "r = %d, i = %d\n", r, i);
3891 rxb = rxq->queue[i];
3893 /* If an RXB doesn't have a Rx queue slot associated with it,
3894 * then a bug has been introduced in the queue refilling
3895 * routines -- catch it here */
3896 BUG_ON(rxb == NULL);
3898 rxq->queue[i] = NULL;
3900 pci_dma_sync_single_for_cpu(priv->pci_dev, rxb->dma_addr,
3902 PCI_DMA_FROMDEVICE);
3903 pkt = (struct iwl3945_rx_packet *)rxb->skb->data;
3905 /* Reclaim a command buffer only if this packet is a response
3906 * to a (driver-originated) command.
3907 * If the packet (e.g. Rx frame) originated from uCode,
3908 * there is no command buffer to reclaim.
3909 * Ucode should set SEQ_RX_FRAME bit if ucode-originated,
3910 * but apparently a few don't get set; catch them here. */
3911 reclaim = !(pkt->hdr.sequence & SEQ_RX_FRAME) &&
3912 (pkt->hdr.cmd != STATISTICS_NOTIFICATION) &&
3913 (pkt->hdr.cmd != REPLY_TX);
3915 /* Based on type of command response or notification,
3916 * handle those that need handling via function in
3917 * rx_handlers table. See iwl3945_setup_rx_handlers() */
3918 if (priv->rx_handlers[pkt->hdr.cmd]) {
3919 IWL_DEBUG(IWL_DL_HOST_COMMAND | IWL_DL_RX | IWL_DL_ISR,
3920 "r = %d, i = %d, %s, 0x%02x\n", r, i,
3921 get_cmd_string(pkt->hdr.cmd), pkt->hdr.cmd);
3922 priv->rx_handlers[pkt->hdr.cmd] (priv, rxb);
3924 /* No handling needed */
3925 IWL_DEBUG(IWL_DL_HOST_COMMAND | IWL_DL_RX | IWL_DL_ISR,
3926 "r %d i %d No handler needed for %s, 0x%02x\n",
3927 r, i, get_cmd_string(pkt->hdr.cmd),
3932 /* Invoke any callbacks, transfer the skb to caller, and
3933 * fire off the (possibly) blocking iwl3945_send_cmd()
3934 * as we reclaim the driver command queue */
3935 if (rxb && rxb->skb)
3936 iwl3945_tx_cmd_complete(priv, rxb);
3938 IWL_WARNING("Claim null rxb?\n");
3941 /* For now we just don't re-use anything. We can tweak this
3942 * later to try and re-use notification packets and SKBs that
3943 * fail to Rx correctly */
3944 if (rxb->skb != NULL) {
3945 priv->alloc_rxb_skb--;
3946 dev_kfree_skb_any(rxb->skb);
3950 pci_unmap_single(priv->pci_dev, rxb->dma_addr,
3951 IWL_RX_BUF_SIZE, PCI_DMA_FROMDEVICE);
3952 spin_lock_irqsave(&rxq->lock, flags);
3953 list_add_tail(&rxb->list, &priv->rxq.rx_used);
3954 spin_unlock_irqrestore(&rxq->lock, flags);
3955 i = (i + 1) & RX_QUEUE_MASK;
3956 /* If there are a lot of unused frames,
3957 * restock the Rx queue so ucode won't assert. */
3962 __iwl3945_rx_replenish(priv);
3968 /* Backtrack one entry */
3970 iwl3945_rx_queue_restock(priv);
3974 * iwl3945_tx_queue_update_write_ptr - Send new write index to hardware
3976 static int iwl3945_tx_queue_update_write_ptr(struct iwl3945_priv *priv,
3977 struct iwl3945_tx_queue *txq)
3981 int txq_id = txq->q.id;
3983 if (txq->need_update == 0)
3986 /* if we're trying to save power */
3987 if (test_bit(STATUS_POWER_PMI, &priv->status)) {
3988 /* wake up nic if it's powered down ...
3989 * uCode will wake up, and interrupt us again, so next
3990 * time we'll skip this part. */
3991 reg = iwl3945_read32(priv, CSR_UCODE_DRV_GP1);
3993 if (reg & CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP) {
3994 IWL_DEBUG_INFO("Requesting wakeup, GP1 = 0x%x\n", reg);
3995 iwl3945_set_bit(priv, CSR_GP_CNTRL,
3996 CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
4000 /* restore this queue's parameters in nic hardware. */
4001 rc = iwl3945_grab_nic_access(priv);
4004 iwl3945_write_direct32(priv, HBUS_TARG_WRPTR,
4005 txq->q.write_ptr | (txq_id << 8));
4006 iwl3945_release_nic_access(priv);
4008 /* else not in power-save mode, uCode will never sleep when we're
4009 * trying to tx (during RFKILL, we're not trying to tx). */
4011 iwl3945_write32(priv, HBUS_TARG_WRPTR,
4012 txq->q.write_ptr | (txq_id << 8));
4014 txq->need_update = 0;
4019 #ifdef CONFIG_IWL3945_DEBUG
4020 static void iwl3945_print_rx_config_cmd(struct iwl3945_rxon_cmd *rxon)
4022 DECLARE_MAC_BUF(mac);
4024 IWL_DEBUG_RADIO("RX CONFIG:\n");
4025 iwl3945_print_hex_dump(IWL_DL_RADIO, (u8 *) rxon, sizeof(*rxon));
4026 IWL_DEBUG_RADIO("u16 channel: 0x%x\n", le16_to_cpu(rxon->channel));
4027 IWL_DEBUG_RADIO("u32 flags: 0x%08X\n", le32_to_cpu(rxon->flags));
4028 IWL_DEBUG_RADIO("u32 filter_flags: 0x%08x\n",
4029 le32_to_cpu(rxon->filter_flags));
4030 IWL_DEBUG_RADIO("u8 dev_type: 0x%x\n", rxon->dev_type);
4031 IWL_DEBUG_RADIO("u8 ofdm_basic_rates: 0x%02x\n",
4032 rxon->ofdm_basic_rates);
4033 IWL_DEBUG_RADIO("u8 cck_basic_rates: 0x%02x\n", rxon->cck_basic_rates);
4034 IWL_DEBUG_RADIO("u8[6] node_addr: %s\n",
4035 print_mac(mac, rxon->node_addr));
4036 IWL_DEBUG_RADIO("u8[6] bssid_addr: %s\n",
4037 print_mac(mac, rxon->bssid_addr));
4038 IWL_DEBUG_RADIO("u16 assoc_id: 0x%x\n", le16_to_cpu(rxon->assoc_id));
4042 static void iwl3945_enable_interrupts(struct iwl3945_priv *priv)
4044 IWL_DEBUG_ISR("Enabling interrupts\n");
4045 set_bit(STATUS_INT_ENABLED, &priv->status);
4046 iwl3945_write32(priv, CSR_INT_MASK, CSR_INI_SET_MASK);
4050 /* call this function to flush any scheduled tasklet */
4051 static inline void iwl_synchronize_irq(struct iwl3945_priv *priv)
4053 /* wait to make sure we flush pedding tasklet*/
4054 synchronize_irq(priv->pci_dev->irq);
4055 tasklet_kill(&priv->irq_tasklet);
4059 static inline void iwl3945_disable_interrupts(struct iwl3945_priv *priv)
4061 clear_bit(STATUS_INT_ENABLED, &priv->status);
4063 /* disable interrupts from uCode/NIC to host */
4064 iwl3945_write32(priv, CSR_INT_MASK, 0x00000000);
4066 /* acknowledge/clear/reset any interrupts still pending
4067 * from uCode or flow handler (Rx/Tx DMA) */
4068 iwl3945_write32(priv, CSR_INT, 0xffffffff);
4069 iwl3945_write32(priv, CSR_FH_INT_STATUS, 0xffffffff);
4070 IWL_DEBUG_ISR("Disabled interrupts\n");
4073 static const char *desc_lookup(int i)
4081 return "BAD_CHECKSUM";
4083 return "NMI_INTERRUPT";
4087 return "FATAL_ERROR";
4093 #define ERROR_START_OFFSET (1 * sizeof(u32))
4094 #define ERROR_ELEM_SIZE (7 * sizeof(u32))
4096 static void iwl3945_dump_nic_error_log(struct iwl3945_priv *priv)
4099 u32 desc, time, count, base, data1;
4100 u32 blink1, blink2, ilink1, ilink2;
4103 base = le32_to_cpu(priv->card_alive.error_event_table_ptr);
4105 if (!iwl3945_hw_valid_rtc_data_addr(base)) {
4106 IWL_ERROR("Not valid error log pointer 0x%08X\n", base);
4110 rc = iwl3945_grab_nic_access(priv);
4112 IWL_WARNING("Can not read from adapter at this time.\n");
4116 count = iwl3945_read_targ_mem(priv, base);
4118 if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) {
4119 IWL_ERROR("Start IWL Error Log Dump:\n");
4120 IWL_ERROR("Status: 0x%08lX, count: %d\n", priv->status, count);
4123 IWL_ERROR("Desc Time asrtPC blink2 "
4124 "ilink1 nmiPC Line\n");
4125 for (i = ERROR_START_OFFSET;
4126 i < (count * ERROR_ELEM_SIZE) + ERROR_START_OFFSET;
4127 i += ERROR_ELEM_SIZE) {
4128 desc = iwl3945_read_targ_mem(priv, base + i);
4130 iwl3945_read_targ_mem(priv, base + i + 1 * sizeof(u32));
4132 iwl3945_read_targ_mem(priv, base + i + 2 * sizeof(u32));
4134 iwl3945_read_targ_mem(priv, base + i + 3 * sizeof(u32));
4136 iwl3945_read_targ_mem(priv, base + i + 4 * sizeof(u32));
4138 iwl3945_read_targ_mem(priv, base + i + 5 * sizeof(u32));
4140 iwl3945_read_targ_mem(priv, base + i + 6 * sizeof(u32));
4143 ("%-13s (#%d) %010u 0x%05X 0x%05X 0x%05X 0x%05X %u\n\n",
4144 desc_lookup(desc), desc, time, blink1, blink2,
4145 ilink1, ilink2, data1);
4148 iwl3945_release_nic_access(priv);
4152 #define EVENT_START_OFFSET (6 * sizeof(u32))
4155 * iwl3945_print_event_log - Dump error event log to syslog
4157 * NOTE: Must be called with iwl3945_grab_nic_access() already obtained!
4159 static void iwl3945_print_event_log(struct iwl3945_priv *priv, u32 start_idx,
4160 u32 num_events, u32 mode)
4163 u32 base; /* SRAM byte address of event log header */
4164 u32 event_size; /* 2 u32s, or 3 u32s if timestamp recorded */
4165 u32 ptr; /* SRAM byte address of log data */
4166 u32 ev, time, data; /* event log data */
4168 if (num_events == 0)
4171 base = le32_to_cpu(priv->card_alive.log_event_table_ptr);
4174 event_size = 2 * sizeof(u32);
4176 event_size = 3 * sizeof(u32);
4178 ptr = base + EVENT_START_OFFSET + (start_idx * event_size);
4180 /* "time" is actually "data" for mode 0 (no timestamp).
4181 * place event id # at far right for easier visual parsing. */
4182 for (i = 0; i < num_events; i++) {
4183 ev = iwl3945_read_targ_mem(priv, ptr);
4185 time = iwl3945_read_targ_mem(priv, ptr);
4188 IWL_ERROR("0x%08x\t%04u\n", time, ev); /* data, ev */
4190 data = iwl3945_read_targ_mem(priv, ptr);
4192 IWL_ERROR("%010u\t0x%08x\t%04u\n", time, data, ev);
4197 static void iwl3945_dump_nic_event_log(struct iwl3945_priv *priv)
4200 u32 base; /* SRAM byte address of event log header */
4201 u32 capacity; /* event log capacity in # entries */
4202 u32 mode; /* 0 - no timestamp, 1 - timestamp recorded */
4203 u32 num_wraps; /* # times uCode wrapped to top of log */
4204 u32 next_entry; /* index of next entry to be written by uCode */
4205 u32 size; /* # entries that we'll print */
4207 base = le32_to_cpu(priv->card_alive.log_event_table_ptr);
4208 if (!iwl3945_hw_valid_rtc_data_addr(base)) {
4209 IWL_ERROR("Invalid event log pointer 0x%08X\n", base);
4213 rc = iwl3945_grab_nic_access(priv);
4215 IWL_WARNING("Can not read from adapter at this time.\n");
4219 /* event log header */
4220 capacity = iwl3945_read_targ_mem(priv, base);
4221 mode = iwl3945_read_targ_mem(priv, base + (1 * sizeof(u32)));
4222 num_wraps = iwl3945_read_targ_mem(priv, base + (2 * sizeof(u32)));
4223 next_entry = iwl3945_read_targ_mem(priv, base + (3 * sizeof(u32)));
4225 size = num_wraps ? capacity : next_entry;
4227 /* bail out if nothing in log */
4229 IWL_ERROR("Start IWL Event Log Dump: nothing in log\n");
4230 iwl3945_release_nic_access(priv);
4234 IWL_ERROR("Start IWL Event Log Dump: display count %d, wraps %d\n",
4237 /* if uCode has wrapped back to top of log, start at the oldest entry,
4238 * i.e the next one that uCode would fill. */
4240 iwl3945_print_event_log(priv, next_entry,
4241 capacity - next_entry, mode);
4243 /* (then/else) start at top of log */
4244 iwl3945_print_event_log(priv, 0, next_entry, mode);
4246 iwl3945_release_nic_access(priv);
4250 * iwl3945_irq_handle_error - called for HW or SW error interrupt from card
4252 static void iwl3945_irq_handle_error(struct iwl3945_priv *priv)
4254 /* Set the FW error flag -- cleared on iwl3945_down */
4255 set_bit(STATUS_FW_ERROR, &priv->status);
4257 /* Cancel currently queued command. */
4258 clear_bit(STATUS_HCMD_ACTIVE, &priv->status);
4260 #ifdef CONFIG_IWL3945_DEBUG
4261 if (iwl3945_debug_level & IWL_DL_FW_ERRORS) {
4262 iwl3945_dump_nic_error_log(priv);
4263 iwl3945_dump_nic_event_log(priv);
4264 iwl3945_print_rx_config_cmd(&priv->staging_rxon);
4268 wake_up_interruptible(&priv->wait_command_queue);
4270 /* Keep the restart process from trying to send host
4271 * commands by clearing the INIT status bit */
4272 clear_bit(STATUS_READY, &priv->status);
4274 if (!test_bit(STATUS_EXIT_PENDING, &priv->status)) {
4275 IWL_DEBUG(IWL_DL_INFO | IWL_DL_FW_ERRORS,
4276 "Restarting adapter due to uCode error.\n");
4278 if (iwl3945_is_associated(priv)) {
4279 memcpy(&priv->recovery_rxon, &priv->active_rxon,
4280 sizeof(priv->recovery_rxon));
4281 priv->error_recovering = 1;
4283 queue_work(priv->workqueue, &priv->restart);
4287 static void iwl3945_error_recovery(struct iwl3945_priv *priv)
4289 unsigned long flags;
4291 memcpy(&priv->staging_rxon, &priv->recovery_rxon,
4292 sizeof(priv->staging_rxon));
4293 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
4294 iwl3945_commit_rxon(priv);
4296 iwl3945_add_station(priv, priv->bssid, 1, 0);
4298 spin_lock_irqsave(&priv->lock, flags);
4299 priv->assoc_id = le16_to_cpu(priv->staging_rxon.assoc_id);
4300 priv->error_recovering = 0;
4301 spin_unlock_irqrestore(&priv->lock, flags);
4304 static void iwl3945_irq_tasklet(struct iwl3945_priv *priv)
4306 u32 inta, handled = 0;
4308 unsigned long flags;
4309 #ifdef CONFIG_IWL3945_DEBUG
4313 spin_lock_irqsave(&priv->lock, flags);
4315 /* Ack/clear/reset pending uCode interrupts.
4316 * Note: Some bits in CSR_INT are "OR" of bits in CSR_FH_INT_STATUS,
4317 * and will clear only when CSR_FH_INT_STATUS gets cleared. */
4318 inta = iwl3945_read32(priv, CSR_INT);
4319 iwl3945_write32(priv, CSR_INT, inta);
4321 /* Ack/clear/reset pending flow-handler (DMA) interrupts.
4322 * Any new interrupts that happen after this, either while we're
4323 * in this tasklet, or later, will show up in next ISR/tasklet. */
4324 inta_fh = iwl3945_read32(priv, CSR_FH_INT_STATUS);
4325 iwl3945_write32(priv, CSR_FH_INT_STATUS, inta_fh);
4327 #ifdef CONFIG_IWL3945_DEBUG
4328 if (iwl3945_debug_level & IWL_DL_ISR) {
4329 /* just for debug */
4330 inta_mask = iwl3945_read32(priv, CSR_INT_MASK);
4331 IWL_DEBUG_ISR("inta 0x%08x, enabled 0x%08x, fh 0x%08x\n",
4332 inta, inta_mask, inta_fh);
4336 /* Since CSR_INT and CSR_FH_INT_STATUS reads and clears are not
4337 * atomic, make sure that inta covers all the interrupts that
4338 * we've discovered, even if FH interrupt came in just after
4339 * reading CSR_INT. */
4340 if (inta_fh & CSR39_FH_INT_RX_MASK)
4341 inta |= CSR_INT_BIT_FH_RX;
4342 if (inta_fh & CSR39_FH_INT_TX_MASK)
4343 inta |= CSR_INT_BIT_FH_TX;
4345 /* Now service all interrupt bits discovered above. */
4346 if (inta & CSR_INT_BIT_HW_ERR) {
4347 IWL_ERROR("Microcode HW error detected. Restarting.\n");
4349 /* Tell the device to stop sending interrupts */
4350 iwl3945_disable_interrupts(priv);
4352 iwl3945_irq_handle_error(priv);
4354 handled |= CSR_INT_BIT_HW_ERR;
4356 spin_unlock_irqrestore(&priv->lock, flags);
4361 #ifdef CONFIG_IWL3945_DEBUG
4362 if (iwl3945_debug_level & (IWL_DL_ISR)) {
4363 /* NIC fires this, but we don't use it, redundant with WAKEUP */
4364 if (inta & CSR_INT_BIT_SCD)
4365 IWL_DEBUG_ISR("Scheduler finished to transmit "
4366 "the frame/frames.\n");
4368 /* Alive notification via Rx interrupt will do the real work */
4369 if (inta & CSR_INT_BIT_ALIVE)
4370 IWL_DEBUG_ISR("Alive interrupt\n");
4373 /* Safely ignore these bits for debug checks below */
4374 inta &= ~(CSR_INT_BIT_SCD | CSR_INT_BIT_ALIVE);
4376 /* HW RF KILL switch toggled (4965 only) */
4377 if (inta & CSR_INT_BIT_RF_KILL) {
4379 if (!(iwl3945_read32(priv, CSR_GP_CNTRL) &
4380 CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW))
4383 IWL_DEBUG(IWL_DL_INFO | IWL_DL_RF_KILL | IWL_DL_ISR,
4384 "RF_KILL bit toggled to %s.\n",
4385 hw_rf_kill ? "disable radio":"enable radio");
4387 /* Queue restart only if RF_KILL switch was set to "kill"
4388 * when we loaded driver, and is now set to "enable".
4389 * After we're Alive, RF_KILL gets handled by
4390 * iwl3945_rx_card_state_notif() */
4391 if (!hw_rf_kill && !test_bit(STATUS_ALIVE, &priv->status)) {
4392 clear_bit(STATUS_RF_KILL_HW, &priv->status);
4393 queue_work(priv->workqueue, &priv->restart);
4396 handled |= CSR_INT_BIT_RF_KILL;
4399 /* Chip got too hot and stopped itself (4965 only) */
4400 if (inta & CSR_INT_BIT_CT_KILL) {
4401 IWL_ERROR("Microcode CT kill error detected.\n");
4402 handled |= CSR_INT_BIT_CT_KILL;
4405 /* Error detected by uCode */
4406 if (inta & CSR_INT_BIT_SW_ERR) {
4407 IWL_ERROR("Microcode SW error detected. Restarting 0x%X.\n",
4409 iwl3945_irq_handle_error(priv);
4410 handled |= CSR_INT_BIT_SW_ERR;
4413 /* uCode wakes up after power-down sleep */
4414 if (inta & CSR_INT_BIT_WAKEUP) {
4415 IWL_DEBUG_ISR("Wakeup interrupt\n");
4416 iwl3945_rx_queue_update_write_ptr(priv, &priv->rxq);
4417 iwl3945_tx_queue_update_write_ptr(priv, &priv->txq[0]);
4418 iwl3945_tx_queue_update_write_ptr(priv, &priv->txq[1]);
4419 iwl3945_tx_queue_update_write_ptr(priv, &priv->txq[2]);
4420 iwl3945_tx_queue_update_write_ptr(priv, &priv->txq[3]);
4421 iwl3945_tx_queue_update_write_ptr(priv, &priv->txq[4]);
4422 iwl3945_tx_queue_update_write_ptr(priv, &priv->txq[5]);
4424 handled |= CSR_INT_BIT_WAKEUP;
4427 /* All uCode command responses, including Tx command responses,
4428 * Rx "responses" (frame-received notification), and other
4429 * notifications from uCode come through here*/
4430 if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX)) {
4431 iwl3945_rx_handle(priv);
4432 handled |= (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX);
4435 if (inta & CSR_INT_BIT_FH_TX) {
4436 IWL_DEBUG_ISR("Tx interrupt\n");
4438 iwl3945_write32(priv, CSR_FH_INT_STATUS, (1 << 6));
4439 if (!iwl3945_grab_nic_access(priv)) {
4440 iwl3945_write_direct32(priv,
4442 (ALM_FH_SRVC_CHNL), 0x0);
4443 iwl3945_release_nic_access(priv);
4445 handled |= CSR_INT_BIT_FH_TX;
4448 if (inta & ~handled)
4449 IWL_ERROR("Unhandled INTA bits 0x%08x\n", inta & ~handled);
4451 if (inta & ~CSR_INI_SET_MASK) {
4452 IWL_WARNING("Disabled INTA bits 0x%08x were pending\n",
4453 inta & ~CSR_INI_SET_MASK);
4454 IWL_WARNING(" with FH_INT = 0x%08x\n", inta_fh);
4457 /* Re-enable all interrupts */
4458 /* only Re-enable if disabled by irq */
4459 if (test_bit(STATUS_INT_ENABLED, &priv->status))
4460 iwl3945_enable_interrupts(priv);
4462 #ifdef CONFIG_IWL3945_DEBUG
4463 if (iwl3945_debug_level & (IWL_DL_ISR)) {
4464 inta = iwl3945_read32(priv, CSR_INT);
4465 inta_mask = iwl3945_read32(priv, CSR_INT_MASK);
4466 inta_fh = iwl3945_read32(priv, CSR_FH_INT_STATUS);
4467 IWL_DEBUG_ISR("End inta 0x%08x, enabled 0x%08x, fh 0x%08x, "
4468 "flags 0x%08lx\n", inta, inta_mask, inta_fh, flags);
4471 spin_unlock_irqrestore(&priv->lock, flags);
4474 static irqreturn_t iwl3945_isr(int irq, void *data)
4476 struct iwl3945_priv *priv = data;
4477 u32 inta, inta_mask;
4482 spin_lock(&priv->lock);
4484 /* Disable (but don't clear!) interrupts here to avoid
4485 * back-to-back ISRs and sporadic interrupts from our NIC.
4486 * If we have something to service, the tasklet will re-enable ints.
4487 * If we *don't* have something, we'll re-enable before leaving here. */
4488 inta_mask = iwl3945_read32(priv, CSR_INT_MASK); /* just for debug */
4489 iwl3945_write32(priv, CSR_INT_MASK, 0x00000000);
4491 /* Discover which interrupts are active/pending */
4492 inta = iwl3945_read32(priv, CSR_INT);
4493 inta_fh = iwl3945_read32(priv, CSR_FH_INT_STATUS);
4495 /* Ignore interrupt if there's nothing in NIC to service.
4496 * This may be due to IRQ shared with another device,
4497 * or due to sporadic interrupts thrown from our NIC. */
4498 if (!inta && !inta_fh) {
4499 IWL_DEBUG_ISR("Ignore interrupt, inta == 0, inta_fh == 0\n");
4503 if ((inta == 0xFFFFFFFF) || ((inta & 0xFFFFFFF0) == 0xa5a5a5a0)) {
4504 /* Hardware disappeared */
4505 IWL_WARNING("HARDWARE GONE?? INTA == 0x%080x\n", inta);
4509 IWL_DEBUG_ISR("ISR inta 0x%08x, enabled 0x%08x, fh 0x%08x\n",
4510 inta, inta_mask, inta_fh);
4512 inta &= ~CSR_INT_BIT_SCD;
4514 /* iwl3945_irq_tasklet() will service interrupts and re-enable them */
4515 if (likely(inta || inta_fh))
4516 tasklet_schedule(&priv->irq_tasklet);
4518 spin_unlock(&priv->lock);
4523 /* re-enable interrupts here since we don't have anything to service. */
4524 /* only Re-enable if disabled by irq */
4525 if (test_bit(STATUS_INT_ENABLED, &priv->status))
4526 iwl3945_enable_interrupts(priv);
4527 spin_unlock(&priv->lock);
4531 /************************** EEPROM BANDS ****************************
4533 * The iwl3945_eeprom_band definitions below provide the mapping from the
4534 * EEPROM contents to the specific channel number supported for each
4537 * For example, iwl3945_priv->eeprom.band_3_channels[4] from the band_3
4538 * definition below maps to physical channel 42 in the 5.2GHz spectrum.
4539 * The specific geography and calibration information for that channel
4540 * is contained in the eeprom map itself.
4542 * During init, we copy the eeprom information and channel map
4543 * information into priv->channel_info_24/52 and priv->channel_map_24/52
4545 * channel_map_24/52 provides the index in the channel_info array for a
4546 * given channel. We have to have two separate maps as there is channel
4547 * overlap with the 2.4GHz and 5.2GHz spectrum as seen in band_1 and
4550 * A value of 0xff stored in the channel_map indicates that the channel
4551 * is not supported by the hardware at all.
4553 * A value of 0xfe in the channel_map indicates that the channel is not
4554 * valid for Tx with the current hardware. This means that
4555 * while the system can tune and receive on a given channel, it may not
4556 * be able to associate or transmit any frames on that
4557 * channel. There is no corresponding channel information for that
4560 *********************************************************************/
4563 static const u8 iwl3945_eeprom_band_1[14] = {
4564 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
4568 static const u8 iwl3945_eeprom_band_2[] = { /* 4915-5080MHz */
4569 183, 184, 185, 187, 188, 189, 192, 196, 7, 8, 11, 12, 16
4572 static const u8 iwl3945_eeprom_band_3[] = { /* 5170-5320MHz */
4573 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
4576 static const u8 iwl3945_eeprom_band_4[] = { /* 5500-5700MHz */
4577 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
4580 static const u8 iwl3945_eeprom_band_5[] = { /* 5725-5825MHz */
4581 145, 149, 153, 157, 161, 165
4584 static void iwl3945_init_band_reference(const struct iwl3945_priv *priv, int band,
4585 int *eeprom_ch_count,
4586 const struct iwl3945_eeprom_channel
4588 const u8 **eeprom_ch_index)
4591 case 1: /* 2.4GHz band */
4592 *eeprom_ch_count = ARRAY_SIZE(iwl3945_eeprom_band_1);
4593 *eeprom_ch_info = priv->eeprom.band_1_channels;
4594 *eeprom_ch_index = iwl3945_eeprom_band_1;
4596 case 2: /* 4.9GHz band */
4597 *eeprom_ch_count = ARRAY_SIZE(iwl3945_eeprom_band_2);
4598 *eeprom_ch_info = priv->eeprom.band_2_channels;
4599 *eeprom_ch_index = iwl3945_eeprom_band_2;
4601 case 3: /* 5.2GHz band */
4602 *eeprom_ch_count = ARRAY_SIZE(iwl3945_eeprom_band_3);
4603 *eeprom_ch_info = priv->eeprom.band_3_channels;
4604 *eeprom_ch_index = iwl3945_eeprom_band_3;
4606 case 4: /* 5.5GHz band */
4607 *eeprom_ch_count = ARRAY_SIZE(iwl3945_eeprom_band_4);
4608 *eeprom_ch_info = priv->eeprom.band_4_channels;
4609 *eeprom_ch_index = iwl3945_eeprom_band_4;
4611 case 5: /* 5.7GHz band */
4612 *eeprom_ch_count = ARRAY_SIZE(iwl3945_eeprom_band_5);
4613 *eeprom_ch_info = priv->eeprom.band_5_channels;
4614 *eeprom_ch_index = iwl3945_eeprom_band_5;
4623 * iwl3945_get_channel_info - Find driver's private channel info
4625 * Based on band and channel number.
4627 const struct iwl3945_channel_info *iwl3945_get_channel_info(const struct iwl3945_priv *priv,
4628 enum ieee80211_band band, u16 channel)
4633 case IEEE80211_BAND_5GHZ:
4634 for (i = 14; i < priv->channel_count; i++) {
4635 if (priv->channel_info[i].channel == channel)
4636 return &priv->channel_info[i];
4640 case IEEE80211_BAND_2GHZ:
4641 if (channel >= 1 && channel <= 14)
4642 return &priv->channel_info[channel - 1];
4644 case IEEE80211_NUM_BANDS:
4651 #define CHECK_AND_PRINT(x) ((eeprom_ch_info[ch].flags & EEPROM_CHANNEL_##x) \
4655 * iwl3945_init_channel_map - Set up driver's info for all possible channels
4657 static int iwl3945_init_channel_map(struct iwl3945_priv *priv)
4659 int eeprom_ch_count = 0;
4660 const u8 *eeprom_ch_index = NULL;
4661 const struct iwl3945_eeprom_channel *eeprom_ch_info = NULL;
4663 struct iwl3945_channel_info *ch_info;
4665 if (priv->channel_count) {
4666 IWL_DEBUG_INFO("Channel map already initialized.\n");
4670 if (priv->eeprom.version < 0x2f) {
4671 IWL_WARNING("Unsupported EEPROM version: 0x%04X\n",
4672 priv->eeprom.version);
4676 IWL_DEBUG_INFO("Initializing regulatory info from EEPROM\n");
4678 priv->channel_count =
4679 ARRAY_SIZE(iwl3945_eeprom_band_1) +
4680 ARRAY_SIZE(iwl3945_eeprom_band_2) +
4681 ARRAY_SIZE(iwl3945_eeprom_band_3) +
4682 ARRAY_SIZE(iwl3945_eeprom_band_4) +
4683 ARRAY_SIZE(iwl3945_eeprom_band_5);
4685 IWL_DEBUG_INFO("Parsing data for %d channels.\n", priv->channel_count);
4687 priv->channel_info = kzalloc(sizeof(struct iwl3945_channel_info) *
4688 priv->channel_count, GFP_KERNEL);
4689 if (!priv->channel_info) {
4690 IWL_ERROR("Could not allocate channel_info\n");
4691 priv->channel_count = 0;
4695 ch_info = priv->channel_info;
4697 /* Loop through the 5 EEPROM bands adding them in order to the
4698 * channel map we maintain (that contains additional information than
4699 * what just in the EEPROM) */
4700 for (band = 1; band <= 5; band++) {
4702 iwl3945_init_band_reference(priv, band, &eeprom_ch_count,
4703 &eeprom_ch_info, &eeprom_ch_index);
4705 /* Loop through each band adding each of the channels */
4706 for (ch = 0; ch < eeprom_ch_count; ch++) {
4707 ch_info->channel = eeprom_ch_index[ch];
4708 ch_info->band = (band == 1) ? IEEE80211_BAND_2GHZ :
4709 IEEE80211_BAND_5GHZ;
4711 /* permanently store EEPROM's channel regulatory flags
4712 * and max power in channel info database. */
4713 ch_info->eeprom = eeprom_ch_info[ch];
4715 /* Copy the run-time flags so they are there even on
4716 * invalid channels */
4717 ch_info->flags = eeprom_ch_info[ch].flags;
4719 if (!(is_channel_valid(ch_info))) {
4720 IWL_DEBUG_INFO("Ch. %d Flags %x [%sGHz] - "
4724 is_channel_a_band(ch_info) ?
4730 /* Initialize regulatory-based run-time data */
4731 ch_info->max_power_avg = ch_info->curr_txpow =
4732 eeprom_ch_info[ch].max_power_avg;
4733 ch_info->scan_power = eeprom_ch_info[ch].max_power_avg;
4734 ch_info->min_power = 0;
4736 IWL_DEBUG_INFO("Ch. %d [%sGHz] %s%s%s%s%s%s(0x%02x"
4737 " %ddBm): Ad-Hoc %ssupported\n",
4739 is_channel_a_band(ch_info) ?
4741 CHECK_AND_PRINT(VALID),
4742 CHECK_AND_PRINT(IBSS),
4743 CHECK_AND_PRINT(ACTIVE),
4744 CHECK_AND_PRINT(RADAR),
4745 CHECK_AND_PRINT(WIDE),
4746 CHECK_AND_PRINT(DFS),
4747 eeprom_ch_info[ch].flags,
4748 eeprom_ch_info[ch].max_power_avg,
4749 ((eeprom_ch_info[ch].
4750 flags & EEPROM_CHANNEL_IBSS)
4751 && !(eeprom_ch_info[ch].
4752 flags & EEPROM_CHANNEL_RADAR))
4755 /* Set the user_txpower_limit to the highest power
4756 * supported by any channel */
4757 if (eeprom_ch_info[ch].max_power_avg >
4758 priv->user_txpower_limit)
4759 priv->user_txpower_limit =
4760 eeprom_ch_info[ch].max_power_avg;
4766 /* Set up txpower settings in driver for all channels */
4767 if (iwl3945_txpower_set_from_eeprom(priv))
4774 * iwl3945_free_channel_map - undo allocations in iwl3945_init_channel_map
4776 static void iwl3945_free_channel_map(struct iwl3945_priv *priv)
4778 kfree(priv->channel_info);
4779 priv->channel_count = 0;
4782 /* For active scan, listen ACTIVE_DWELL_TIME (msec) on each channel after
4783 * sending probe req. This should be set long enough to hear probe responses
4784 * from more than one AP. */
4785 #define IWL_ACTIVE_DWELL_TIME_24 (30) /* all times in msec */
4786 #define IWL_ACTIVE_DWELL_TIME_52 (20)
4788 #define IWL_ACTIVE_DWELL_FACTOR_24GHZ (3)
4789 #define IWL_ACTIVE_DWELL_FACTOR_52GHZ (2)
4791 /* For faster active scanning, scan will move to the next channel if fewer than
4792 * PLCP_QUIET_THRESH packets are heard on this channel within
4793 * ACTIVE_QUIET_TIME after sending probe request. This shortens the dwell
4794 * time if it's a quiet channel (nothing responded to our probe, and there's
4795 * no other traffic).
4796 * Disable "quiet" feature by setting PLCP_QUIET_THRESH to 0. */
4797 #define IWL_PLCP_QUIET_THRESH __constant_cpu_to_le16(1) /* packets */
4798 #define IWL_ACTIVE_QUIET_TIME __constant_cpu_to_le16(10) /* msec */
4800 /* For passive scan, listen PASSIVE_DWELL_TIME (msec) on each channel.
4801 * Must be set longer than active dwell time.
4802 * For the most reliable scan, set > AP beacon interval (typically 100msec). */
4803 #define IWL_PASSIVE_DWELL_TIME_24 (20) /* all times in msec */
4804 #define IWL_PASSIVE_DWELL_TIME_52 (10)
4805 #define IWL_PASSIVE_DWELL_BASE (100)
4806 #define IWL_CHANNEL_TUNE_TIME 5
4808 #define IWL_SCAN_PROBE_MASK(n) cpu_to_le32((BIT(n) | (BIT(n) - BIT(1))))
4810 static inline u16 iwl3945_get_active_dwell_time(struct iwl3945_priv *priv,
4811 enum ieee80211_band band,
4814 if (band == IEEE80211_BAND_5GHZ)
4815 return IWL_ACTIVE_DWELL_TIME_52 +
4816 IWL_ACTIVE_DWELL_FACTOR_52GHZ * (n_probes + 1);
4818 return IWL_ACTIVE_DWELL_TIME_24 +
4819 IWL_ACTIVE_DWELL_FACTOR_24GHZ * (n_probes + 1);
4822 static u16 iwl3945_get_passive_dwell_time(struct iwl3945_priv *priv,
4823 enum ieee80211_band band)
4825 u16 passive = (band == IEEE80211_BAND_2GHZ) ?
4826 IWL_PASSIVE_DWELL_BASE + IWL_PASSIVE_DWELL_TIME_24 :
4827 IWL_PASSIVE_DWELL_BASE + IWL_PASSIVE_DWELL_TIME_52;
4829 if (iwl3945_is_associated(priv)) {
4830 /* If we're associated, we clamp the maximum passive
4831 * dwell time to be 98% of the beacon interval (minus
4832 * 2 * channel tune time) */
4833 passive = priv->beacon_int;
4834 if ((passive > IWL_PASSIVE_DWELL_BASE) || !passive)
4835 passive = IWL_PASSIVE_DWELL_BASE;
4836 passive = (passive * 98) / 100 - IWL_CHANNEL_TUNE_TIME * 2;
4842 static int iwl3945_get_channels_for_scan(struct iwl3945_priv *priv,
4843 enum ieee80211_band band,
4844 u8 is_active, u8 n_probes,
4845 struct iwl3945_scan_channel *scan_ch)
4847 const struct ieee80211_channel *channels = NULL;
4848 const struct ieee80211_supported_band *sband;
4849 const struct iwl3945_channel_info *ch_info;
4850 u16 passive_dwell = 0;
4851 u16 active_dwell = 0;
4854 sband = iwl3945_get_band(priv, band);
4858 channels = sband->channels;
4860 active_dwell = iwl3945_get_active_dwell_time(priv, band, n_probes);
4861 passive_dwell = iwl3945_get_passive_dwell_time(priv, band);
4863 if (passive_dwell <= active_dwell)
4864 passive_dwell = active_dwell + 1;
4866 for (i = 0, added = 0; i < sband->n_channels; i++) {
4867 if (channels[i].flags & IEEE80211_CHAN_DISABLED)
4870 scan_ch->channel = channels[i].hw_value;
4872 ch_info = iwl3945_get_channel_info(priv, band, scan_ch->channel);
4873 if (!is_channel_valid(ch_info)) {
4874 IWL_DEBUG_SCAN("Channel %d is INVALID for this band.\n",
4879 if (!is_active || is_channel_passive(ch_info) ||
4880 (channels[i].flags & IEEE80211_CHAN_PASSIVE_SCAN))
4881 scan_ch->type = 0; /* passive */
4883 scan_ch->type = 1; /* active */
4885 if ((scan_ch->type & 1) && n_probes)
4886 scan_ch->type |= IWL_SCAN_PROBE_MASK(n_probes);
4888 scan_ch->active_dwell = cpu_to_le16(active_dwell);
4889 scan_ch->passive_dwell = cpu_to_le16(passive_dwell);
4891 /* Set txpower levels to defaults */
4892 scan_ch->tpc.dsp_atten = 110;
4893 /* scan_pwr_info->tpc.dsp_atten; */
4895 /*scan_pwr_info->tpc.tx_gain; */
4896 if (band == IEEE80211_BAND_5GHZ)
4897 scan_ch->tpc.tx_gain = ((1 << 5) | (3 << 3)) | 3;
4899 scan_ch->tpc.tx_gain = ((1 << 5) | (5 << 3));
4900 /* NOTE: if we were doing 6Mb OFDM for scans we'd use
4902 * scan_ch->tpc.tx_gain = ((1 << 5) | (2 << 3)) | 3;
4906 IWL_DEBUG_SCAN("Scanning %d [%s %d]\n",
4908 (scan_ch->type & 1) ? "ACTIVE" : "PASSIVE",
4909 (scan_ch->type & 1) ?
4910 active_dwell : passive_dwell);
4916 IWL_DEBUG_SCAN("total channels to scan %d \n", added);
4920 static void iwl3945_init_hw_rates(struct iwl3945_priv *priv,
4921 struct ieee80211_rate *rates)
4925 for (i = 0; i < IWL_RATE_COUNT; i++) {
4926 rates[i].bitrate = iwl3945_rates[i].ieee * 5;
4927 rates[i].hw_value = i; /* Rate scaling will work on indexes */
4928 rates[i].hw_value_short = i;
4930 if ((i > IWL_LAST_OFDM_RATE) || (i < IWL_FIRST_OFDM_RATE)) {
4932 * If CCK != 1M then set short preamble rate flag.
4934 rates[i].flags |= (iwl3945_rates[i].plcp == 10) ?
4935 0 : IEEE80211_RATE_SHORT_PREAMBLE;
4941 * iwl3945_init_geos - Initialize mac80211's geo/channel info based from eeprom
4943 static int iwl3945_init_geos(struct iwl3945_priv *priv)
4945 struct iwl3945_channel_info *ch;
4946 struct ieee80211_supported_band *sband;
4947 struct ieee80211_channel *channels;
4948 struct ieee80211_channel *geo_ch;
4949 struct ieee80211_rate *rates;
4952 if (priv->bands[IEEE80211_BAND_2GHZ].n_bitrates ||
4953 priv->bands[IEEE80211_BAND_5GHZ].n_bitrates) {
4954 IWL_DEBUG_INFO("Geography modes already initialized.\n");
4955 set_bit(STATUS_GEO_CONFIGURED, &priv->status);
4959 channels = kzalloc(sizeof(struct ieee80211_channel) *
4960 priv->channel_count, GFP_KERNEL);
4964 rates = kzalloc((sizeof(struct ieee80211_rate) * (IWL_RATE_COUNT + 1)),
4971 /* 5.2GHz channels start after the 2.4GHz channels */
4972 sband = &priv->bands[IEEE80211_BAND_5GHZ];
4973 sband->channels = &channels[ARRAY_SIZE(iwl3945_eeprom_band_1)];
4975 sband->bitrates = &rates[IWL_FIRST_OFDM_RATE];
4976 sband->n_bitrates = IWL_RATE_COUNT - IWL_FIRST_OFDM_RATE;
4978 sband = &priv->bands[IEEE80211_BAND_2GHZ];
4979 sband->channels = channels;
4981 sband->bitrates = rates;
4982 sband->n_bitrates = IWL_RATE_COUNT;
4984 priv->ieee_channels = channels;
4985 priv->ieee_rates = rates;
4987 iwl3945_init_hw_rates(priv, rates);
4989 for (i = 0; i < priv->channel_count; i++) {
4990 ch = &priv->channel_info[i];
4992 /* FIXME: might be removed if scan is OK*/
4993 if (!is_channel_valid(ch))
4996 if (is_channel_a_band(ch))
4997 sband = &priv->bands[IEEE80211_BAND_5GHZ];
4999 sband = &priv->bands[IEEE80211_BAND_2GHZ];
5001 geo_ch = &sband->channels[sband->n_channels++];
5003 geo_ch->center_freq = ieee80211_channel_to_frequency(ch->channel);
5004 geo_ch->max_power = ch->max_power_avg;
5005 geo_ch->max_antenna_gain = 0xff;
5006 geo_ch->hw_value = ch->channel;
5008 if (is_channel_valid(ch)) {
5009 if (!(ch->flags & EEPROM_CHANNEL_IBSS))
5010 geo_ch->flags |= IEEE80211_CHAN_NO_IBSS;
5012 if (!(ch->flags & EEPROM_CHANNEL_ACTIVE))
5013 geo_ch->flags |= IEEE80211_CHAN_PASSIVE_SCAN;
5015 if (ch->flags & EEPROM_CHANNEL_RADAR)
5016 geo_ch->flags |= IEEE80211_CHAN_RADAR;
5018 if (ch->max_power_avg > priv->max_channel_txpower_limit)
5019 priv->max_channel_txpower_limit =
5022 geo_ch->flags |= IEEE80211_CHAN_DISABLED;
5025 /* Save flags for reg domain usage */
5026 geo_ch->orig_flags = geo_ch->flags;
5028 IWL_DEBUG_INFO("Channel %d Freq=%d[%sGHz] %s flag=0%X\n",
5029 ch->channel, geo_ch->center_freq,
5030 is_channel_a_band(ch) ? "5.2" : "2.4",
5031 geo_ch->flags & IEEE80211_CHAN_DISABLED ?
5032 "restricted" : "valid",
5036 if ((priv->bands[IEEE80211_BAND_5GHZ].n_channels == 0) &&
5037 priv->cfg->sku & IWL_SKU_A) {
5038 printk(KERN_INFO DRV_NAME
5039 ": Incorrectly detected BG card as ABG. Please send "
5040 "your PCI ID 0x%04X:0x%04X to maintainer.\n",
5041 priv->pci_dev->device, priv->pci_dev->subsystem_device);
5042 priv->cfg->sku &= ~IWL_SKU_A;
5045 printk(KERN_INFO DRV_NAME
5046 ": Tunable channels: %d 802.11bg, %d 802.11a channels\n",
5047 priv->bands[IEEE80211_BAND_2GHZ].n_channels,
5048 priv->bands[IEEE80211_BAND_5GHZ].n_channels);
5050 if (priv->bands[IEEE80211_BAND_2GHZ].n_channels)
5051 priv->hw->wiphy->bands[IEEE80211_BAND_2GHZ] =
5052 &priv->bands[IEEE80211_BAND_2GHZ];
5053 if (priv->bands[IEEE80211_BAND_5GHZ].n_channels)
5054 priv->hw->wiphy->bands[IEEE80211_BAND_5GHZ] =
5055 &priv->bands[IEEE80211_BAND_5GHZ];
5057 set_bit(STATUS_GEO_CONFIGURED, &priv->status);
5063 * iwl3945_free_geos - undo allocations in iwl3945_init_geos
5065 static void iwl3945_free_geos(struct iwl3945_priv *priv)
5067 kfree(priv->ieee_channels);
5068 kfree(priv->ieee_rates);
5069 clear_bit(STATUS_GEO_CONFIGURED, &priv->status);
5072 /******************************************************************************
5074 * uCode download functions
5076 ******************************************************************************/
5078 static void iwl3945_dealloc_ucode_pci(struct iwl3945_priv *priv)
5080 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_code);
5081 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data);
5082 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
5083 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init);
5084 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init_data);
5085 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_boot);
5089 * iwl3945_verify_inst_full - verify runtime uCode image in card vs. host,
5090 * looking at all data.
5092 static int iwl3945_verify_inst_full(struct iwl3945_priv *priv, __le32 *image, u32 len)
5099 IWL_DEBUG_INFO("ucode inst image size is %u\n", len);
5101 rc = iwl3945_grab_nic_access(priv);
5105 iwl3945_write_direct32(priv, HBUS_TARG_MEM_RADDR, RTC_INST_LOWER_BOUND);
5108 for (; len > 0; len -= sizeof(u32), image++) {
5109 /* read data comes through single port, auto-incr addr */
5110 /* NOTE: Use the debugless read so we don't flood kernel log
5111 * if IWL_DL_IO is set */
5112 val = _iwl3945_read_direct32(priv, HBUS_TARG_MEM_RDAT);
5113 if (val != le32_to_cpu(*image)) {
5114 IWL_ERROR("uCode INST section is invalid at "
5115 "offset 0x%x, is 0x%x, s/b 0x%x\n",
5116 save_len - len, val, le32_to_cpu(*image));
5124 iwl3945_release_nic_access(priv);
5127 IWL_DEBUG_INFO("ucode image in INSTRUCTION memory is good\n");
5134 * iwl3945_verify_inst_sparse - verify runtime uCode image in card vs. host,
5135 * using sample data 100 bytes apart. If these sample points are good,
5136 * it's a pretty good bet that everything between them is good, too.
5138 static int iwl3945_verify_inst_sparse(struct iwl3945_priv *priv, __le32 *image, u32 len)
5145 IWL_DEBUG_INFO("ucode inst image size is %u\n", len);
5147 rc = iwl3945_grab_nic_access(priv);
5151 for (i = 0; i < len; i += 100, image += 100/sizeof(u32)) {
5152 /* read data comes through single port, auto-incr addr */
5153 /* NOTE: Use the debugless read so we don't flood kernel log
5154 * if IWL_DL_IO is set */
5155 iwl3945_write_direct32(priv, HBUS_TARG_MEM_RADDR,
5156 i + RTC_INST_LOWER_BOUND);
5157 val = _iwl3945_read_direct32(priv, HBUS_TARG_MEM_RDAT);
5158 if (val != le32_to_cpu(*image)) {
5159 #if 0 /* Enable this if you want to see details */
5160 IWL_ERROR("uCode INST section is invalid at "
5161 "offset 0x%x, is 0x%x, s/b 0x%x\n",
5171 iwl3945_release_nic_access(priv);
5178 * iwl3945_verify_ucode - determine which instruction image is in SRAM,
5179 * and verify its contents
5181 static int iwl3945_verify_ucode(struct iwl3945_priv *priv)
5188 image = (__le32 *)priv->ucode_boot.v_addr;
5189 len = priv->ucode_boot.len;
5190 rc = iwl3945_verify_inst_sparse(priv, image, len);
5192 IWL_DEBUG_INFO("Bootstrap uCode is good in inst SRAM\n");
5196 /* Try initialize */
5197 image = (__le32 *)priv->ucode_init.v_addr;
5198 len = priv->ucode_init.len;
5199 rc = iwl3945_verify_inst_sparse(priv, image, len);
5201 IWL_DEBUG_INFO("Initialize uCode is good in inst SRAM\n");
5205 /* Try runtime/protocol */
5206 image = (__le32 *)priv->ucode_code.v_addr;
5207 len = priv->ucode_code.len;
5208 rc = iwl3945_verify_inst_sparse(priv, image, len);
5210 IWL_DEBUG_INFO("Runtime uCode is good in inst SRAM\n");
5214 IWL_ERROR("NO VALID UCODE IMAGE IN INSTRUCTION SRAM!!\n");
5216 /* Since nothing seems to match, show first several data entries in
5217 * instruction SRAM, so maybe visual inspection will give a clue.
5218 * Selection of bootstrap image (vs. other images) is arbitrary. */
5219 image = (__le32 *)priv->ucode_boot.v_addr;
5220 len = priv->ucode_boot.len;
5221 rc = iwl3945_verify_inst_full(priv, image, len);
5227 /* check contents of special bootstrap uCode SRAM */
5228 static int iwl3945_verify_bsm(struct iwl3945_priv *priv)
5230 __le32 *image = priv->ucode_boot.v_addr;
5231 u32 len = priv->ucode_boot.len;
5235 IWL_DEBUG_INFO("Begin verify bsm\n");
5237 /* verify BSM SRAM contents */
5238 val = iwl3945_read_prph(priv, BSM_WR_DWCOUNT_REG);
5239 for (reg = BSM_SRAM_LOWER_BOUND;
5240 reg < BSM_SRAM_LOWER_BOUND + len;
5241 reg += sizeof(u32), image++) {
5242 val = iwl3945_read_prph(priv, reg);
5243 if (val != le32_to_cpu(*image)) {
5244 IWL_ERROR("BSM uCode verification failed at "
5245 "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n",
5246 BSM_SRAM_LOWER_BOUND,
5247 reg - BSM_SRAM_LOWER_BOUND, len,
5248 val, le32_to_cpu(*image));
5253 IWL_DEBUG_INFO("BSM bootstrap uCode image OK\n");
5259 * iwl3945_load_bsm - Load bootstrap instructions
5263 * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
5264 * in special SRAM that does not power down during RFKILL. When powering back
5265 * up after power-saving sleeps (or during initial uCode load), the BSM loads
5266 * the bootstrap program into the on-board processor, and starts it.
5268 * The bootstrap program loads (via DMA) instructions and data for a new
5269 * program from host DRAM locations indicated by the host driver in the
5270 * BSM_DRAM_* registers. Once the new program is loaded, it starts
5273 * When initializing the NIC, the host driver points the BSM to the
5274 * "initialize" uCode image. This uCode sets up some internal data, then
5275 * notifies host via "initialize alive" that it is complete.
5277 * The host then replaces the BSM_DRAM_* pointer values to point to the
5278 * normal runtime uCode instructions and a backup uCode data cache buffer
5279 * (filled initially with starting data values for the on-board processor),
5280 * then triggers the "initialize" uCode to load and launch the runtime uCode,
5281 * which begins normal operation.
5283 * When doing a power-save shutdown, runtime uCode saves data SRAM into
5284 * the backup data cache in DRAM before SRAM is powered down.
5286 * When powering back up, the BSM loads the bootstrap program. This reloads
5287 * the runtime uCode instructions and the backup data cache into SRAM,
5288 * and re-launches the runtime uCode from where it left off.
5290 static int iwl3945_load_bsm(struct iwl3945_priv *priv)
5292 __le32 *image = priv->ucode_boot.v_addr;
5293 u32 len = priv->ucode_boot.len;
5303 IWL_DEBUG_INFO("Begin load bsm\n");
5305 /* make sure bootstrap program is no larger than BSM's SRAM size */
5306 if (len > IWL_MAX_BSM_SIZE)
5309 /* Tell bootstrap uCode where to find the "Initialize" uCode
5310 * in host DRAM ... host DRAM physical address bits 31:0 for 3945.
5311 * NOTE: iwl3945_initialize_alive_start() will replace these values,
5312 * after the "initialize" uCode has run, to point to
5313 * runtime/protocol instructions and backup data cache. */
5314 pinst = priv->ucode_init.p_addr;
5315 pdata = priv->ucode_init_data.p_addr;
5316 inst_len = priv->ucode_init.len;
5317 data_len = priv->ucode_init_data.len;
5319 rc = iwl3945_grab_nic_access(priv);
5323 iwl3945_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
5324 iwl3945_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
5325 iwl3945_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG, inst_len);
5326 iwl3945_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG, data_len);
5328 /* Fill BSM memory with bootstrap instructions */
5329 for (reg_offset = BSM_SRAM_LOWER_BOUND;
5330 reg_offset < BSM_SRAM_LOWER_BOUND + len;
5331 reg_offset += sizeof(u32), image++)
5332 _iwl3945_write_prph(priv, reg_offset,
5333 le32_to_cpu(*image));
5335 rc = iwl3945_verify_bsm(priv);
5337 iwl3945_release_nic_access(priv);
5341 /* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */
5342 iwl3945_write_prph(priv, BSM_WR_MEM_SRC_REG, 0x0);
5343 iwl3945_write_prph(priv, BSM_WR_MEM_DST_REG,
5344 RTC_INST_LOWER_BOUND);
5345 iwl3945_write_prph(priv, BSM_WR_DWCOUNT_REG, len / sizeof(u32));
5347 /* Load bootstrap code into instruction SRAM now,
5348 * to prepare to load "initialize" uCode */
5349 iwl3945_write_prph(priv, BSM_WR_CTRL_REG,
5350 BSM_WR_CTRL_REG_BIT_START);
5352 /* Wait for load of bootstrap uCode to finish */
5353 for (i = 0; i < 100; i++) {
5354 done = iwl3945_read_prph(priv, BSM_WR_CTRL_REG);
5355 if (!(done & BSM_WR_CTRL_REG_BIT_START))
5360 IWL_DEBUG_INFO("BSM write complete, poll %d iterations\n", i);
5362 IWL_ERROR("BSM write did not complete!\n");
5366 /* Enable future boot loads whenever power management unit triggers it
5367 * (e.g. when powering back up after power-save shutdown) */
5368 iwl3945_write_prph(priv, BSM_WR_CTRL_REG,
5369 BSM_WR_CTRL_REG_BIT_START_EN);
5371 iwl3945_release_nic_access(priv);
5376 static void iwl3945_nic_start(struct iwl3945_priv *priv)
5378 /* Remove all resets to allow NIC to operate */
5379 iwl3945_write32(priv, CSR_RESET, 0);
5383 * iwl3945_read_ucode - Read uCode images from disk file.
5385 * Copy into buffers for card to fetch via bus-mastering
5387 static int iwl3945_read_ucode(struct iwl3945_priv *priv)
5389 struct iwl3945_ucode *ucode;
5391 const struct firmware *ucode_raw;
5392 /* firmware file name contains uCode/driver compatibility version */
5393 const char *name = priv->cfg->fw_name;
5396 u32 ver, inst_size, data_size, init_size, init_data_size, boot_size;
5398 /* Ask kernel firmware_class module to get the boot firmware off disk.
5399 * request_firmware() is synchronous, file is in memory on return. */
5400 ret = request_firmware(&ucode_raw, name, &priv->pci_dev->dev);
5402 IWL_ERROR("%s firmware file req failed: Reason %d\n",
5407 IWL_DEBUG_INFO("Got firmware '%s' file (%zd bytes) from disk\n",
5408 name, ucode_raw->size);
5410 /* Make sure that we got at least our header! */
5411 if (ucode_raw->size < sizeof(*ucode)) {
5412 IWL_ERROR("File size way too small!\n");
5417 /* Data from ucode file: header followed by uCode images */
5418 ucode = (void *)ucode_raw->data;
5420 ver = le32_to_cpu(ucode->ver);
5421 inst_size = le32_to_cpu(ucode->inst_size);
5422 data_size = le32_to_cpu(ucode->data_size);
5423 init_size = le32_to_cpu(ucode->init_size);
5424 init_data_size = le32_to_cpu(ucode->init_data_size);
5425 boot_size = le32_to_cpu(ucode->boot_size);
5427 IWL_DEBUG_INFO("f/w package hdr ucode version = 0x%x\n", ver);
5428 IWL_DEBUG_INFO("f/w package hdr runtime inst size = %u\n", inst_size);
5429 IWL_DEBUG_INFO("f/w package hdr runtime data size = %u\n", data_size);
5430 IWL_DEBUG_INFO("f/w package hdr init inst size = %u\n", init_size);
5431 IWL_DEBUG_INFO("f/w package hdr init data size = %u\n", init_data_size);
5432 IWL_DEBUG_INFO("f/w package hdr boot inst size = %u\n", boot_size);
5434 /* Verify size of file vs. image size info in file's header */
5435 if (ucode_raw->size < sizeof(*ucode) +
5436 inst_size + data_size + init_size +
5437 init_data_size + boot_size) {
5439 IWL_DEBUG_INFO("uCode file size %d too small\n",
5440 (int)ucode_raw->size);
5445 /* Verify that uCode images will fit in card's SRAM */
5446 if (inst_size > IWL_MAX_INST_SIZE) {
5447 IWL_DEBUG_INFO("uCode instr len %d too large to fit in\n",
5453 if (data_size > IWL_MAX_DATA_SIZE) {
5454 IWL_DEBUG_INFO("uCode data len %d too large to fit in\n",
5459 if (init_size > IWL_MAX_INST_SIZE) {
5460 IWL_DEBUG_INFO("uCode init instr len %d too large to fit in\n",
5465 if (init_data_size > IWL_MAX_DATA_SIZE) {
5466 IWL_DEBUG_INFO("uCode init data len %d too large to fit in\n",
5471 if (boot_size > IWL_MAX_BSM_SIZE) {
5472 IWL_DEBUG_INFO("uCode boot instr len %d too large to fit in\n",
5478 /* Allocate ucode buffers for card's bus-master loading ... */
5480 /* Runtime instructions and 2 copies of data:
5481 * 1) unmodified from disk
5482 * 2) backup cache for save/restore during power-downs */
5483 priv->ucode_code.len = inst_size;
5484 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_code);
5486 priv->ucode_data.len = data_size;
5487 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data);
5489 priv->ucode_data_backup.len = data_size;
5490 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
5492 if (!priv->ucode_code.v_addr || !priv->ucode_data.v_addr ||
5493 !priv->ucode_data_backup.v_addr)
5496 /* Initialization instructions and data */
5497 if (init_size && init_data_size) {
5498 priv->ucode_init.len = init_size;
5499 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init);
5501 priv->ucode_init_data.len = init_data_size;
5502 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init_data);
5504 if (!priv->ucode_init.v_addr || !priv->ucode_init_data.v_addr)
5508 /* Bootstrap (instructions only, no data) */
5510 priv->ucode_boot.len = boot_size;
5511 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_boot);
5513 if (!priv->ucode_boot.v_addr)
5517 /* Copy images into buffers for card's bus-master reads ... */
5519 /* Runtime instructions (first block of data in file) */
5520 src = &ucode->data[0];
5521 len = priv->ucode_code.len;
5522 IWL_DEBUG_INFO("Copying (but not loading) uCode instr len %Zd\n", len);
5523 memcpy(priv->ucode_code.v_addr, src, len);
5524 IWL_DEBUG_INFO("uCode instr buf vaddr = 0x%p, paddr = 0x%08x\n",
5525 priv->ucode_code.v_addr, (u32)priv->ucode_code.p_addr);
5527 /* Runtime data (2nd block)
5528 * NOTE: Copy into backup buffer will be done in iwl3945_up() */
5529 src = &ucode->data[inst_size];
5530 len = priv->ucode_data.len;
5531 IWL_DEBUG_INFO("Copying (but not loading) uCode data len %Zd\n", len);
5532 memcpy(priv->ucode_data.v_addr, src, len);
5533 memcpy(priv->ucode_data_backup.v_addr, src, len);
5535 /* Initialization instructions (3rd block) */
5537 src = &ucode->data[inst_size + data_size];
5538 len = priv->ucode_init.len;
5539 IWL_DEBUG_INFO("Copying (but not loading) init instr len %Zd\n",
5541 memcpy(priv->ucode_init.v_addr, src, len);
5544 /* Initialization data (4th block) */
5545 if (init_data_size) {
5546 src = &ucode->data[inst_size + data_size + init_size];
5547 len = priv->ucode_init_data.len;
5548 IWL_DEBUG_INFO("Copying (but not loading) init data len %d\n",
5550 memcpy(priv->ucode_init_data.v_addr, src, len);
5553 /* Bootstrap instructions (5th block) */
5554 src = &ucode->data[inst_size + data_size + init_size + init_data_size];
5555 len = priv->ucode_boot.len;
5556 IWL_DEBUG_INFO("Copying (but not loading) boot instr len %d\n",
5558 memcpy(priv->ucode_boot.v_addr, src, len);
5560 /* We have our copies now, allow OS release its copies */
5561 release_firmware(ucode_raw);
5565 IWL_ERROR("failed to allocate pci memory\n");
5567 iwl3945_dealloc_ucode_pci(priv);
5570 release_firmware(ucode_raw);
5578 * iwl3945_set_ucode_ptrs - Set uCode address location
5580 * Tell initialization uCode where to find runtime uCode.
5582 * BSM registers initially contain pointers to initialization uCode.
5583 * We need to replace them to load runtime uCode inst and data,
5584 * and to save runtime data when powering down.
5586 static int iwl3945_set_ucode_ptrs(struct iwl3945_priv *priv)
5591 unsigned long flags;
5593 /* bits 31:0 for 3945 */
5594 pinst = priv->ucode_code.p_addr;
5595 pdata = priv->ucode_data_backup.p_addr;
5597 spin_lock_irqsave(&priv->lock, flags);
5598 rc = iwl3945_grab_nic_access(priv);
5600 spin_unlock_irqrestore(&priv->lock, flags);
5604 /* Tell bootstrap uCode where to find image to load */
5605 iwl3945_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
5606 iwl3945_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
5607 iwl3945_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG,
5608 priv->ucode_data.len);
5610 /* Inst bytecount must be last to set up, bit 31 signals uCode
5611 * that all new ptr/size info is in place */
5612 iwl3945_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG,
5613 priv->ucode_code.len | BSM_DRAM_INST_LOAD);
5615 iwl3945_release_nic_access(priv);
5617 spin_unlock_irqrestore(&priv->lock, flags);
5619 IWL_DEBUG_INFO("Runtime uCode pointers are set.\n");
5625 * iwl3945_init_alive_start - Called after REPLY_ALIVE notification received
5627 * Called after REPLY_ALIVE notification received from "initialize" uCode.
5629 * Tell "initialize" uCode to go ahead and load the runtime uCode.
5631 static void iwl3945_init_alive_start(struct iwl3945_priv *priv)
5633 /* Check alive response for "valid" sign from uCode */
5634 if (priv->card_alive_init.is_valid != UCODE_VALID_OK) {
5635 /* We had an error bringing up the hardware, so take it
5636 * all the way back down so we can try again */
5637 IWL_DEBUG_INFO("Initialize Alive failed.\n");
5641 /* Bootstrap uCode has loaded initialize uCode ... verify inst image.
5642 * This is a paranoid check, because we would not have gotten the
5643 * "initialize" alive if code weren't properly loaded. */
5644 if (iwl3945_verify_ucode(priv)) {
5645 /* Runtime instruction load was bad;
5646 * take it all the way back down so we can try again */
5647 IWL_DEBUG_INFO("Bad \"initialize\" uCode load.\n");
5651 /* Send pointers to protocol/runtime uCode image ... init code will
5652 * load and launch runtime uCode, which will send us another "Alive"
5654 IWL_DEBUG_INFO("Initialization Alive received.\n");
5655 if (iwl3945_set_ucode_ptrs(priv)) {
5656 /* Runtime instruction load won't happen;
5657 * take it all the way back down so we can try again */
5658 IWL_DEBUG_INFO("Couldn't set up uCode pointers.\n");
5664 queue_work(priv->workqueue, &priv->restart);
5669 * iwl3945_alive_start - called after REPLY_ALIVE notification received
5670 * from protocol/runtime uCode (initialization uCode's
5671 * Alive gets handled by iwl3945_init_alive_start()).
5673 static void iwl3945_alive_start(struct iwl3945_priv *priv)
5676 int thermal_spin = 0;
5679 IWL_DEBUG_INFO("Runtime Alive received.\n");
5681 if (priv->card_alive.is_valid != UCODE_VALID_OK) {
5682 /* We had an error bringing up the hardware, so take it
5683 * all the way back down so we can try again */
5684 IWL_DEBUG_INFO("Alive failed.\n");
5688 /* Initialize uCode has loaded Runtime uCode ... verify inst image.
5689 * This is a paranoid check, because we would not have gotten the
5690 * "runtime" alive if code weren't properly loaded. */
5691 if (iwl3945_verify_ucode(priv)) {
5692 /* Runtime instruction load was bad;
5693 * take it all the way back down so we can try again */
5694 IWL_DEBUG_INFO("Bad runtime uCode load.\n");
5698 iwl3945_clear_stations_table(priv);
5700 rc = iwl3945_grab_nic_access(priv);
5702 IWL_WARNING("Can not read rfkill status from adapter\n");
5706 rfkill = iwl3945_read_prph(priv, APMG_RFKILL_REG);
5707 IWL_DEBUG_INFO("RFKILL status: 0x%x\n", rfkill);
5708 iwl3945_release_nic_access(priv);
5711 clear_bit(STATUS_RF_KILL_HW, &priv->status);
5712 /* if rfkill is not on, then wait for thermal
5713 * sensor in adapter to kick in */
5714 while (iwl3945_hw_get_temperature(priv) == 0) {
5720 IWL_DEBUG_INFO("Thermal calibration took %dus\n",
5723 set_bit(STATUS_RF_KILL_HW, &priv->status);
5725 /* After the ALIVE response, we can send commands to 3945 uCode */
5726 set_bit(STATUS_ALIVE, &priv->status);
5728 /* Clear out the uCode error bit if it is set */
5729 clear_bit(STATUS_FW_ERROR, &priv->status);
5731 if (iwl3945_is_rfkill(priv))
5734 ieee80211_wake_queues(priv->hw);
5736 priv->active_rate = priv->rates_mask;
5737 priv->active_rate_basic = priv->rates_mask & IWL_BASIC_RATES_MASK;
5739 iwl3945_send_power_mode(priv, IWL_POWER_LEVEL(priv->power_mode));
5741 if (iwl3945_is_associated(priv)) {
5742 struct iwl3945_rxon_cmd *active_rxon =
5743 (struct iwl3945_rxon_cmd *)(&priv->active_rxon);
5745 memcpy(&priv->staging_rxon, &priv->active_rxon,
5746 sizeof(priv->staging_rxon));
5747 active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;
5749 /* Initialize our rx_config data */
5750 iwl3945_connection_init_rx_config(priv);
5751 memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
5754 /* Configure Bluetooth device coexistence support */
5755 iwl3945_send_bt_config(priv);
5757 /* Configure the adapter for unassociated operation */
5758 iwl3945_commit_rxon(priv);
5760 iwl3945_reg_txpower_periodic(priv);
5762 iwl3945_led_register(priv);
5764 IWL_DEBUG_INFO("ALIVE processing complete.\n");
5765 set_bit(STATUS_READY, &priv->status);
5766 wake_up_interruptible(&priv->wait_command_queue);
5768 if (priv->error_recovering)
5769 iwl3945_error_recovery(priv);
5774 queue_work(priv->workqueue, &priv->restart);
5777 static void iwl3945_cancel_deferred_work(struct iwl3945_priv *priv);
5779 static void __iwl3945_down(struct iwl3945_priv *priv)
5781 unsigned long flags;
5782 int exit_pending = test_bit(STATUS_EXIT_PENDING, &priv->status);
5783 struct ieee80211_conf *conf = NULL;
5785 IWL_DEBUG_INFO(DRV_NAME " is going down\n");
5787 conf = ieee80211_get_hw_conf(priv->hw);
5790 set_bit(STATUS_EXIT_PENDING, &priv->status);
5792 iwl3945_led_unregister(priv);
5793 iwl3945_clear_stations_table(priv);
5795 /* Unblock any waiting calls */
5796 wake_up_interruptible_all(&priv->wait_command_queue);
5798 /* Wipe out the EXIT_PENDING status bit if we are not actually
5799 * exiting the module */
5801 clear_bit(STATUS_EXIT_PENDING, &priv->status);
5803 /* stop and reset the on-board processor */
5804 iwl3945_write32(priv, CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET);
5806 /* tell the device to stop sending interrupts */
5807 spin_lock_irqsave(&priv->lock, flags);
5808 iwl3945_disable_interrupts(priv);
5809 spin_unlock_irqrestore(&priv->lock, flags);
5810 iwl_synchronize_irq(priv);
5812 if (priv->mac80211_registered)
5813 ieee80211_stop_queues(priv->hw);
5815 /* If we have not previously called iwl3945_init() then
5816 * clear all bits but the RF Kill and SUSPEND bits and return */
5817 if (!iwl3945_is_init(priv)) {
5818 priv->status = test_bit(STATUS_RF_KILL_HW, &priv->status) <<
5820 test_bit(STATUS_RF_KILL_SW, &priv->status) <<
5822 test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
5823 STATUS_GEO_CONFIGURED |
5824 test_bit(STATUS_IN_SUSPEND, &priv->status) <<
5826 test_bit(STATUS_EXIT_PENDING, &priv->status) <<
5827 STATUS_EXIT_PENDING;
5831 /* ...otherwise clear out all the status bits but the RF Kill and
5832 * SUSPEND bits and continue taking the NIC down. */
5833 priv->status &= test_bit(STATUS_RF_KILL_HW, &priv->status) <<
5835 test_bit(STATUS_RF_KILL_SW, &priv->status) <<
5837 test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
5838 STATUS_GEO_CONFIGURED |
5839 test_bit(STATUS_IN_SUSPEND, &priv->status) <<
5841 test_bit(STATUS_FW_ERROR, &priv->status) <<
5843 test_bit(STATUS_EXIT_PENDING, &priv->status) <<
5844 STATUS_EXIT_PENDING;
5846 spin_lock_irqsave(&priv->lock, flags);
5847 iwl3945_clear_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
5848 spin_unlock_irqrestore(&priv->lock, flags);
5850 iwl3945_hw_txq_ctx_stop(priv);
5851 iwl3945_hw_rxq_stop(priv);
5853 spin_lock_irqsave(&priv->lock, flags);
5854 if (!iwl3945_grab_nic_access(priv)) {
5855 iwl3945_write_prph(priv, APMG_CLK_DIS_REG,
5856 APMG_CLK_VAL_DMA_CLK_RQT);
5857 iwl3945_release_nic_access(priv);
5859 spin_unlock_irqrestore(&priv->lock, flags);
5863 iwl3945_hw_nic_stop_master(priv);
5864 iwl3945_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET);
5865 iwl3945_hw_nic_reset(priv);
5868 memset(&priv->card_alive, 0, sizeof(struct iwl3945_alive_resp));
5870 if (priv->ibss_beacon)
5871 dev_kfree_skb(priv->ibss_beacon);
5872 priv->ibss_beacon = NULL;
5874 /* clear out any free frames */
5875 iwl3945_clear_free_frames(priv);
5878 static void iwl3945_down(struct iwl3945_priv *priv)
5880 mutex_lock(&priv->mutex);
5881 __iwl3945_down(priv);
5882 mutex_unlock(&priv->mutex);
5884 iwl3945_cancel_deferred_work(priv);
5887 #define MAX_HW_RESTARTS 5
5889 static int __iwl3945_up(struct iwl3945_priv *priv)
5893 if (test_bit(STATUS_EXIT_PENDING, &priv->status)) {
5894 IWL_WARNING("Exit pending; will not bring the NIC up\n");
5898 if (test_bit(STATUS_RF_KILL_SW, &priv->status)) {
5899 IWL_WARNING("Radio disabled by SW RF kill (module "
5904 if (!priv->ucode_data_backup.v_addr || !priv->ucode_data.v_addr) {
5905 IWL_ERROR("ucode not available for device bringup\n");
5909 /* If platform's RF_KILL switch is NOT set to KILL */
5910 if (iwl3945_read32(priv, CSR_GP_CNTRL) &
5911 CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
5912 clear_bit(STATUS_RF_KILL_HW, &priv->status);
5914 set_bit(STATUS_RF_KILL_HW, &priv->status);
5915 if (!test_bit(STATUS_IN_SUSPEND, &priv->status)) {
5916 IWL_WARNING("Radio disabled by HW RF Kill switch\n");
5921 iwl3945_write32(priv, CSR_INT, 0xFFFFFFFF);
5923 rc = iwl3945_hw_nic_init(priv);
5925 IWL_ERROR("Unable to int nic\n");
5929 /* make sure rfkill handshake bits are cleared */
5930 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
5931 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR,
5932 CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
5934 /* clear (again), then enable host interrupts */
5935 iwl3945_write32(priv, CSR_INT, 0xFFFFFFFF);
5936 iwl3945_enable_interrupts(priv);
5938 /* really make sure rfkill handshake bits are cleared */
5939 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
5940 iwl3945_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
5942 /* Copy original ucode data image from disk into backup cache.
5943 * This will be used to initialize the on-board processor's
5944 * data SRAM for a clean start when the runtime program first loads. */
5945 memcpy(priv->ucode_data_backup.v_addr, priv->ucode_data.v_addr,
5946 priv->ucode_data.len);
5948 /* We return success when we resume from suspend and rf_kill is on. */
5949 if (test_bit(STATUS_RF_KILL_HW, &priv->status))
5952 for (i = 0; i < MAX_HW_RESTARTS; i++) {
5954 iwl3945_clear_stations_table(priv);
5956 /* load bootstrap state machine,
5957 * load bootstrap program into processor's memory,
5958 * prepare to load the "initialize" uCode */
5959 rc = iwl3945_load_bsm(priv);
5962 IWL_ERROR("Unable to set up bootstrap uCode: %d\n", rc);
5966 /* start card; "initialize" will load runtime ucode */
5967 iwl3945_nic_start(priv);
5969 IWL_DEBUG_INFO(DRV_NAME " is coming up\n");
5974 set_bit(STATUS_EXIT_PENDING, &priv->status);
5975 __iwl3945_down(priv);
5976 clear_bit(STATUS_EXIT_PENDING, &priv->status);
5978 /* tried to restart and config the device for as long as our
5979 * patience could withstand */
5980 IWL_ERROR("Unable to initialize device after %d attempts.\n", i);
5985 /*****************************************************************************
5987 * Workqueue callbacks
5989 *****************************************************************************/
5991 static void iwl3945_bg_init_alive_start(struct work_struct *data)
5993 struct iwl3945_priv *priv =
5994 container_of(data, struct iwl3945_priv, init_alive_start.work);
5996 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
5999 mutex_lock(&priv->mutex);
6000 iwl3945_init_alive_start(priv);
6001 mutex_unlock(&priv->mutex);
6004 static void iwl3945_bg_alive_start(struct work_struct *data)
6006 struct iwl3945_priv *priv =
6007 container_of(data, struct iwl3945_priv, alive_start.work);
6009 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6012 mutex_lock(&priv->mutex);
6013 iwl3945_alive_start(priv);
6014 mutex_unlock(&priv->mutex);
6015 ieee80211_notify_mac(priv->hw, IEEE80211_NOTIFY_RE_ASSOC);
6018 static void iwl3945_bg_rf_kill(struct work_struct *work)
6020 struct iwl3945_priv *priv = container_of(work, struct iwl3945_priv, rf_kill);
6022 wake_up_interruptible(&priv->wait_command_queue);
6024 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6027 mutex_lock(&priv->mutex);
6029 if (!iwl3945_is_rfkill(priv)) {
6030 IWL_DEBUG(IWL_DL_INFO | IWL_DL_RF_KILL,
6031 "HW and/or SW RF Kill no longer active, restarting "
6033 if (!test_bit(STATUS_EXIT_PENDING, &priv->status))
6034 queue_work(priv->workqueue, &priv->restart);
6037 if (!test_bit(STATUS_RF_KILL_HW, &priv->status))
6038 IWL_DEBUG_RF_KILL("Can not turn radio back on - "
6039 "disabled by SW switch\n");
6041 IWL_WARNING("Radio Frequency Kill Switch is On:\n"
6042 "Kill switch must be turned off for "
6043 "wireless networking to work.\n");
6046 mutex_unlock(&priv->mutex);
6047 iwl3945_rfkill_set_hw_state(priv);
6050 static void iwl3945_bg_set_monitor(struct work_struct *work)
6052 struct iwl3945_priv *priv = container_of(work,
6053 struct iwl3945_priv, set_monitor);
6055 IWL_DEBUG(IWL_DL_STATE, "setting monitor mode\n");
6057 mutex_lock(&priv->mutex);
6059 if (!iwl3945_is_ready(priv))
6060 IWL_DEBUG(IWL_DL_STATE, "leave - not ready\n");
6062 if (iwl3945_set_mode(priv, NL80211_IFTYPE_MONITOR) != 0)
6063 IWL_ERROR("iwl3945_set_mode() failed\n");
6065 mutex_unlock(&priv->mutex);
6068 #define IWL_SCAN_CHECK_WATCHDOG (7 * HZ)
6070 static void iwl3945_bg_scan_check(struct work_struct *data)
6072 struct iwl3945_priv *priv =
6073 container_of(data, struct iwl3945_priv, scan_check.work);
6075 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6078 mutex_lock(&priv->mutex);
6079 if (test_bit(STATUS_SCANNING, &priv->status) ||
6080 test_bit(STATUS_SCAN_ABORTING, &priv->status)) {
6081 IWL_DEBUG(IWL_DL_INFO | IWL_DL_SCAN,
6082 "Scan completion watchdog resetting adapter (%dms)\n",
6083 jiffies_to_msecs(IWL_SCAN_CHECK_WATCHDOG));
6085 if (!test_bit(STATUS_EXIT_PENDING, &priv->status))
6086 iwl3945_send_scan_abort(priv);
6088 mutex_unlock(&priv->mutex);
6091 static void iwl3945_bg_request_scan(struct work_struct *data)
6093 struct iwl3945_priv *priv =
6094 container_of(data, struct iwl3945_priv, request_scan);
6095 struct iwl3945_host_cmd cmd = {
6096 .id = REPLY_SCAN_CMD,
6097 .len = sizeof(struct iwl3945_scan_cmd),
6098 .meta.flags = CMD_SIZE_HUGE,
6101 struct iwl3945_scan_cmd *scan;
6102 struct ieee80211_conf *conf = NULL;
6104 enum ieee80211_band band;
6106 conf = ieee80211_get_hw_conf(priv->hw);
6108 mutex_lock(&priv->mutex);
6110 if (!iwl3945_is_ready(priv)) {
6111 IWL_WARNING("request scan called when driver not ready.\n");
6115 /* Make sure the scan wasn't cancelled before this queued work
6116 * was given the chance to run... */
6117 if (!test_bit(STATUS_SCANNING, &priv->status))
6120 /* This should never be called or scheduled if there is currently
6121 * a scan active in the hardware. */
6122 if (test_bit(STATUS_SCAN_HW, &priv->status)) {
6123 IWL_DEBUG_INFO("Multiple concurrent scan requests in parallel. "
6124 "Ignoring second request.\n");
6129 if (test_bit(STATUS_EXIT_PENDING, &priv->status)) {
6130 IWL_DEBUG_SCAN("Aborting scan due to device shutdown\n");
6134 if (test_bit(STATUS_SCAN_ABORTING, &priv->status)) {
6135 IWL_DEBUG_HC("Scan request while abort pending. Queuing.\n");
6139 if (iwl3945_is_rfkill(priv)) {
6140 IWL_DEBUG_HC("Aborting scan due to RF Kill activation\n");
6144 if (!test_bit(STATUS_READY, &priv->status)) {
6145 IWL_DEBUG_HC("Scan request while uninitialized. Queuing.\n");
6149 if (!priv->scan_bands) {
6150 IWL_DEBUG_HC("Aborting scan due to no requested bands\n");
6155 priv->scan = kmalloc(sizeof(struct iwl3945_scan_cmd) +
6156 IWL_MAX_SCAN_SIZE, GFP_KERNEL);
6163 memset(scan, 0, sizeof(struct iwl3945_scan_cmd) + IWL_MAX_SCAN_SIZE);
6165 scan->quiet_plcp_th = IWL_PLCP_QUIET_THRESH;
6166 scan->quiet_time = IWL_ACTIVE_QUIET_TIME;
6168 if (iwl3945_is_associated(priv)) {
6171 u32 suspend_time = 100;
6172 u32 scan_suspend_time = 100;
6173 unsigned long flags;
6175 IWL_DEBUG_INFO("Scanning while associated...\n");
6177 spin_lock_irqsave(&priv->lock, flags);
6178 interval = priv->beacon_int;
6179 spin_unlock_irqrestore(&priv->lock, flags);
6181 scan->suspend_time = 0;
6182 scan->max_out_time = cpu_to_le32(200 * 1024);
6184 interval = suspend_time;
6186 * suspend time format:
6187 * 0-19: beacon interval in usec (time before exec.)
6189 * 24-31: number of beacons (suspend between channels)
6192 extra = (suspend_time / interval) << 24;
6193 scan_suspend_time = 0xFF0FFFFF &
6194 (extra | ((suspend_time % interval) * 1024));
6196 scan->suspend_time = cpu_to_le32(scan_suspend_time);
6197 IWL_DEBUG_SCAN("suspend_time 0x%X beacon interval %d\n",
6198 scan_suspend_time, interval);
6201 /* We should add the ability for user to lock to PASSIVE ONLY */
6202 if (priv->one_direct_scan) {
6204 ("Kicking off one direct scan for '%s'\n",
6205 iwl3945_escape_essid(priv->direct_ssid,
6206 priv->direct_ssid_len));
6207 scan->direct_scan[0].id = WLAN_EID_SSID;
6208 scan->direct_scan[0].len = priv->direct_ssid_len;
6209 memcpy(scan->direct_scan[0].ssid,
6210 priv->direct_ssid, priv->direct_ssid_len);
6212 } else if (!iwl3945_is_associated(priv) && priv->essid_len) {
6214 ("Kicking off one direct scan for '%s' when not associated\n",
6215 iwl3945_escape_essid(priv->essid, priv->essid_len));
6216 scan->direct_scan[0].id = WLAN_EID_SSID;
6217 scan->direct_scan[0].len = priv->essid_len;
6218 memcpy(scan->direct_scan[0].ssid, priv->essid, priv->essid_len);
6221 IWL_DEBUG_SCAN("Kicking off one indirect scan.\n");
6223 /* We don't build a direct scan probe request; the uCode will do
6224 * that based on the direct_mask added to each channel entry */
6225 scan->tx_cmd.len = cpu_to_le16(
6226 iwl3945_fill_probe_req(priv, (struct ieee80211_mgmt *)scan->data,
6227 IWL_MAX_SCAN_SIZE - sizeof(*scan), 0));
6228 scan->tx_cmd.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK;
6229 scan->tx_cmd.sta_id = priv->hw_setting.bcast_sta_id;
6230 scan->tx_cmd.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
6232 /* flags + rate selection */
6234 if (priv->scan_bands & BIT(IEEE80211_BAND_2GHZ)) {
6235 scan->flags = RXON_FLG_BAND_24G_MSK | RXON_FLG_AUTO_DETECT_MSK;
6236 scan->tx_cmd.rate = IWL_RATE_1M_PLCP;
6237 scan->good_CRC_th = 0;
6238 band = IEEE80211_BAND_2GHZ;
6239 } else if (priv->scan_bands & BIT(IEEE80211_BAND_5GHZ)) {
6240 scan->tx_cmd.rate = IWL_RATE_6M_PLCP;
6241 scan->good_CRC_th = IWL_GOOD_CRC_TH;
6242 band = IEEE80211_BAND_5GHZ;
6244 IWL_WARNING("Invalid scan band count\n");
6248 /* select Rx antennas */
6249 scan->flags |= iwl3945_get_antenna_flags(priv);
6251 if (priv->iw_mode == NL80211_IFTYPE_MONITOR)
6252 scan->filter_flags = RXON_FILTER_PROMISC_MSK;
6254 scan->channel_count =
6255 iwl3945_get_channels_for_scan(priv, band, 1, /* active */
6257 (void *)&scan->data[le16_to_cpu(scan->tx_cmd.len)]);
6259 if (scan->channel_count == 0) {
6260 IWL_DEBUG_SCAN("channel count %d\n", scan->channel_count);
6264 cmd.len += le16_to_cpu(scan->tx_cmd.len) +
6265 scan->channel_count * sizeof(struct iwl3945_scan_channel);
6267 scan->len = cpu_to_le16(cmd.len);
6269 set_bit(STATUS_SCAN_HW, &priv->status);
6270 rc = iwl3945_send_cmd_sync(priv, &cmd);
6274 queue_delayed_work(priv->workqueue, &priv->scan_check,
6275 IWL_SCAN_CHECK_WATCHDOG);
6277 mutex_unlock(&priv->mutex);
6281 /* can not perform scan make sure we clear scanning
6282 * bits from status so next scan request can be performed.
6283 * if we dont clear scanning status bit here all next scan
6286 clear_bit(STATUS_SCAN_HW, &priv->status);
6287 clear_bit(STATUS_SCANNING, &priv->status);
6289 /* inform mac80211 scan aborted */
6290 queue_work(priv->workqueue, &priv->scan_completed);
6291 mutex_unlock(&priv->mutex);
6294 static void iwl3945_bg_up(struct work_struct *data)
6296 struct iwl3945_priv *priv = container_of(data, struct iwl3945_priv, up);
6298 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6301 mutex_lock(&priv->mutex);
6303 mutex_unlock(&priv->mutex);
6304 iwl3945_rfkill_set_hw_state(priv);
6307 static void iwl3945_bg_restart(struct work_struct *data)
6309 struct iwl3945_priv *priv = container_of(data, struct iwl3945_priv, restart);
6311 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6315 queue_work(priv->workqueue, &priv->up);
6318 static void iwl3945_bg_rx_replenish(struct work_struct *data)
6320 struct iwl3945_priv *priv =
6321 container_of(data, struct iwl3945_priv, rx_replenish);
6323 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6326 mutex_lock(&priv->mutex);
6327 iwl3945_rx_replenish(priv);
6328 mutex_unlock(&priv->mutex);
6331 #define IWL_DELAY_NEXT_SCAN (HZ*2)
6333 static void iwl3945_post_associate(struct iwl3945_priv *priv)
6336 struct ieee80211_conf *conf = NULL;
6337 DECLARE_MAC_BUF(mac);
6339 if (priv->iw_mode == NL80211_IFTYPE_AP) {
6340 IWL_ERROR("%s Should not be called in AP mode\n", __func__);
6345 IWL_DEBUG_ASSOC("Associated as %d to: %s\n",
6347 print_mac(mac, priv->active_rxon.bssid_addr));
6349 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6352 if (!priv->vif || !priv->is_open)
6355 iwl3945_scan_cancel_timeout(priv, 200);
6357 conf = ieee80211_get_hw_conf(priv->hw);
6359 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
6360 iwl3945_commit_rxon(priv);
6362 memset(&priv->rxon_timing, 0, sizeof(struct iwl3945_rxon_time_cmd));
6363 iwl3945_setup_rxon_timing(priv);
6364 rc = iwl3945_send_cmd_pdu(priv, REPLY_RXON_TIMING,
6365 sizeof(priv->rxon_timing), &priv->rxon_timing);
6367 IWL_WARNING("REPLY_RXON_TIMING failed - "
6368 "Attempting to continue.\n");
6370 priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
6372 priv->staging_rxon.assoc_id = cpu_to_le16(priv->assoc_id);
6374 IWL_DEBUG_ASSOC("assoc id %d beacon interval %d\n",
6375 priv->assoc_id, priv->beacon_int);
6377 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_PREAMBLE)
6378 priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
6380 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
6382 if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) {
6383 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_SLOT_TIME)
6384 priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
6386 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
6388 if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
6389 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
6393 iwl3945_commit_rxon(priv);
6395 switch (priv->iw_mode) {
6396 case NL80211_IFTYPE_STATION:
6397 iwl3945_rate_scale_init(priv->hw, IWL_AP_ID);
6400 case NL80211_IFTYPE_ADHOC:
6402 /* clear out the station table */
6403 iwl3945_clear_stations_table(priv);
6405 iwl3945_add_station(priv, iwl3945_broadcast_addr, 0, 0);
6406 iwl3945_add_station(priv, priv->bssid, 0, 0);
6407 iwl3945_sync_sta(priv, IWL_STA_ID,
6408 (priv->band == IEEE80211_BAND_5GHZ) ?
6409 IWL_RATE_6M_PLCP : IWL_RATE_1M_PLCP,
6411 iwl3945_rate_scale_init(priv->hw, IWL_STA_ID);
6412 iwl3945_send_beacon_cmd(priv);
6417 IWL_ERROR("%s Should not be called in %d mode\n",
6418 __func__, priv->iw_mode);
6422 iwl3945_activate_qos(priv, 0);
6424 /* we have just associated, don't start scan too early */
6425 priv->next_scan_jiffies = jiffies + IWL_DELAY_NEXT_SCAN;
6428 static void iwl3945_bg_abort_scan(struct work_struct *work)
6430 struct iwl3945_priv *priv = container_of(work, struct iwl3945_priv, abort_scan);
6432 if (!iwl3945_is_ready(priv))
6435 mutex_lock(&priv->mutex);
6437 set_bit(STATUS_SCAN_ABORTING, &priv->status);
6438 iwl3945_send_scan_abort(priv);
6440 mutex_unlock(&priv->mutex);
6443 static int iwl3945_mac_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
6445 static void iwl3945_bg_scan_completed(struct work_struct *work)
6447 struct iwl3945_priv *priv =
6448 container_of(work, struct iwl3945_priv, scan_completed);
6450 IWL_DEBUG(IWL_DL_INFO | IWL_DL_SCAN, "SCAN complete scan\n");
6452 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6455 if (test_bit(STATUS_CONF_PENDING, &priv->status))
6456 iwl3945_mac_config(priv->hw, ieee80211_get_hw_conf(priv->hw));
6458 ieee80211_scan_completed(priv->hw);
6460 /* Since setting the TXPOWER may have been deferred while
6461 * performing the scan, fire one off */
6462 mutex_lock(&priv->mutex);
6463 iwl3945_hw_reg_send_txpower(priv);
6464 mutex_unlock(&priv->mutex);
6467 /*****************************************************************************
6469 * mac80211 entry point functions
6471 *****************************************************************************/
6473 #define UCODE_READY_TIMEOUT (2 * HZ)
6475 static int iwl3945_mac_start(struct ieee80211_hw *hw)
6477 struct iwl3945_priv *priv = hw->priv;
6480 IWL_DEBUG_MAC80211("enter\n");
6482 if (pci_enable_device(priv->pci_dev)) {
6483 IWL_ERROR("Fail to pci_enable_device\n");
6486 pci_restore_state(priv->pci_dev);
6487 pci_enable_msi(priv->pci_dev);
6489 ret = request_irq(priv->pci_dev->irq, iwl3945_isr, IRQF_SHARED,
6492 IWL_ERROR("Error allocating IRQ %d\n", priv->pci_dev->irq);
6493 goto out_disable_msi;
6496 /* we should be verifying the device is ready to be opened */
6497 mutex_lock(&priv->mutex);
6499 memset(&priv->staging_rxon, 0, sizeof(struct iwl3945_rxon_cmd));
6500 /* fetch ucode file from disk, alloc and copy to bus-master buffers ...
6501 * ucode filename and max sizes are card-specific. */
6503 if (!priv->ucode_code.len) {
6504 ret = iwl3945_read_ucode(priv);
6506 IWL_ERROR("Could not read microcode: %d\n", ret);
6507 mutex_unlock(&priv->mutex);
6508 goto out_release_irq;
6512 ret = __iwl3945_up(priv);
6514 mutex_unlock(&priv->mutex);
6516 iwl3945_rfkill_set_hw_state(priv);
6519 goto out_release_irq;
6521 IWL_DEBUG_INFO("Start UP work.\n");
6523 if (test_bit(STATUS_IN_SUSPEND, &priv->status))
6526 /* Wait for START_ALIVE from ucode. Otherwise callbacks from
6527 * mac80211 will not be run successfully. */
6528 ret = wait_event_interruptible_timeout(priv->wait_command_queue,
6529 test_bit(STATUS_READY, &priv->status),
6530 UCODE_READY_TIMEOUT);
6532 if (!test_bit(STATUS_READY, &priv->status)) {
6533 IWL_ERROR("Wait for START_ALIVE timeout after %dms.\n",
6534 jiffies_to_msecs(UCODE_READY_TIMEOUT));
6536 goto out_release_irq;
6541 IWL_DEBUG_MAC80211("leave\n");
6545 free_irq(priv->pci_dev->irq, priv);
6547 pci_disable_msi(priv->pci_dev);
6548 pci_disable_device(priv->pci_dev);
6550 IWL_DEBUG_MAC80211("leave - failed\n");
6554 static void iwl3945_mac_stop(struct ieee80211_hw *hw)
6556 struct iwl3945_priv *priv = hw->priv;
6558 IWL_DEBUG_MAC80211("enter\n");
6560 if (!priv->is_open) {
6561 IWL_DEBUG_MAC80211("leave - skip\n");
6567 if (iwl3945_is_ready_rf(priv)) {
6568 /* stop mac, cancel any scan request and clear
6569 * RXON_FILTER_ASSOC_MSK BIT
6571 mutex_lock(&priv->mutex);
6572 iwl3945_scan_cancel_timeout(priv, 100);
6573 mutex_unlock(&priv->mutex);
6578 flush_workqueue(priv->workqueue);
6579 free_irq(priv->pci_dev->irq, priv);
6580 pci_disable_msi(priv->pci_dev);
6581 pci_save_state(priv->pci_dev);
6582 pci_disable_device(priv->pci_dev);
6584 IWL_DEBUG_MAC80211("leave\n");
6587 static int iwl3945_mac_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
6589 struct iwl3945_priv *priv = hw->priv;
6591 IWL_DEBUG_MAC80211("enter\n");
6593 IWL_DEBUG_TX("dev->xmit(%d bytes) at rate 0x%02x\n", skb->len,
6594 ieee80211_get_tx_rate(hw, IEEE80211_SKB_CB(skb))->bitrate);
6596 if (iwl3945_tx_skb(priv, skb))
6597 dev_kfree_skb_any(skb);
6599 IWL_DEBUG_MAC80211("leave\n");
6603 static int iwl3945_mac_add_interface(struct ieee80211_hw *hw,
6604 struct ieee80211_if_init_conf *conf)
6606 struct iwl3945_priv *priv = hw->priv;
6607 unsigned long flags;
6608 DECLARE_MAC_BUF(mac);
6610 IWL_DEBUG_MAC80211("enter: type %d\n", conf->type);
6613 IWL_DEBUG_MAC80211("leave - vif != NULL\n");
6617 spin_lock_irqsave(&priv->lock, flags);
6618 priv->vif = conf->vif;
6620 spin_unlock_irqrestore(&priv->lock, flags);
6622 mutex_lock(&priv->mutex);
6624 if (conf->mac_addr) {
6625 IWL_DEBUG_MAC80211("Set: %s\n", print_mac(mac, conf->mac_addr));
6626 memcpy(priv->mac_addr, conf->mac_addr, ETH_ALEN);
6629 if (iwl3945_is_ready(priv))
6630 iwl3945_set_mode(priv, conf->type);
6632 mutex_unlock(&priv->mutex);
6634 IWL_DEBUG_MAC80211("leave\n");
6639 * iwl3945_mac_config - mac80211 config callback
6641 * We ignore conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME since it seems to
6642 * be set inappropriately and the driver currently sets the hardware up to
6643 * use it whenever needed.
6645 static int iwl3945_mac_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
6647 struct iwl3945_priv *priv = hw->priv;
6648 const struct iwl3945_channel_info *ch_info;
6649 unsigned long flags;
6652 mutex_lock(&priv->mutex);
6653 IWL_DEBUG_MAC80211("enter to channel %d\n", conf->channel->hw_value);
6655 if (!iwl3945_is_ready(priv)) {
6656 IWL_DEBUG_MAC80211("leave - not ready\n");
6661 if (unlikely(!iwl3945_param_disable_hw_scan &&
6662 test_bit(STATUS_SCANNING, &priv->status))) {
6663 IWL_DEBUG_MAC80211("leave - scanning\n");
6664 set_bit(STATUS_CONF_PENDING, &priv->status);
6665 mutex_unlock(&priv->mutex);
6669 spin_lock_irqsave(&priv->lock, flags);
6671 ch_info = iwl3945_get_channel_info(priv, conf->channel->band,
6672 conf->channel->hw_value);
6673 if (!is_channel_valid(ch_info)) {
6674 IWL_DEBUG_SCAN("Channel %d [%d] is INVALID for this band.\n",
6675 conf->channel->hw_value, conf->channel->band);
6676 IWL_DEBUG_MAC80211("leave - invalid channel\n");
6677 spin_unlock_irqrestore(&priv->lock, flags);
6682 iwl3945_set_rxon_channel(priv, conf->channel->band, conf->channel->hw_value);
6684 iwl3945_set_flags_for_phymode(priv, conf->channel->band);
6686 /* The list of supported rates and rate mask can be different
6687 * for each phymode; since the phymode may have changed, reset
6688 * the rate mask to what mac80211 lists */
6689 iwl3945_set_rate(priv);
6691 spin_unlock_irqrestore(&priv->lock, flags);
6693 #ifdef IEEE80211_CONF_CHANNEL_SWITCH
6694 if (conf->flags & IEEE80211_CONF_CHANNEL_SWITCH) {
6695 iwl3945_hw_channel_switch(priv, conf->channel);
6700 iwl3945_radio_kill_sw(priv, !conf->radio_enabled);
6702 if (!conf->radio_enabled) {
6703 IWL_DEBUG_MAC80211("leave - radio disabled\n");
6707 if (iwl3945_is_rfkill(priv)) {
6708 IWL_DEBUG_MAC80211("leave - RF kill\n");
6713 iwl3945_set_rate(priv);
6715 if (memcmp(&priv->active_rxon,
6716 &priv->staging_rxon, sizeof(priv->staging_rxon)))
6717 iwl3945_commit_rxon(priv);
6719 IWL_DEBUG_INFO("No re-sending same RXON configuration.\n");
6721 IWL_DEBUG_MAC80211("leave\n");
6724 clear_bit(STATUS_CONF_PENDING, &priv->status);
6725 mutex_unlock(&priv->mutex);
6729 static void iwl3945_config_ap(struct iwl3945_priv *priv)
6733 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
6736 /* The following should be done only at AP bring up */
6737 if (!(iwl3945_is_associated(priv))) {
6739 /* RXON - unassoc (to set timing command) */
6740 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
6741 iwl3945_commit_rxon(priv);
6744 memset(&priv->rxon_timing, 0, sizeof(struct iwl3945_rxon_time_cmd));
6745 iwl3945_setup_rxon_timing(priv);
6746 rc = iwl3945_send_cmd_pdu(priv, REPLY_RXON_TIMING,
6747 sizeof(priv->rxon_timing), &priv->rxon_timing);
6749 IWL_WARNING("REPLY_RXON_TIMING failed - "
6750 "Attempting to continue.\n");
6752 /* FIXME: what should be the assoc_id for AP? */
6753 priv->staging_rxon.assoc_id = cpu_to_le16(priv->assoc_id);
6754 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_PREAMBLE)
6755 priv->staging_rxon.flags |=
6756 RXON_FLG_SHORT_PREAMBLE_MSK;
6758 priv->staging_rxon.flags &=
6759 ~RXON_FLG_SHORT_PREAMBLE_MSK;
6761 if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) {
6762 if (priv->assoc_capability &
6763 WLAN_CAPABILITY_SHORT_SLOT_TIME)
6764 priv->staging_rxon.flags |=
6765 RXON_FLG_SHORT_SLOT_MSK;
6767 priv->staging_rxon.flags &=
6768 ~RXON_FLG_SHORT_SLOT_MSK;
6770 if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
6771 priv->staging_rxon.flags &=
6772 ~RXON_FLG_SHORT_SLOT_MSK;
6774 /* restore RXON assoc */
6775 priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
6776 iwl3945_commit_rxon(priv);
6777 iwl3945_add_station(priv, iwl3945_broadcast_addr, 0, 0);
6779 iwl3945_send_beacon_cmd(priv);
6781 /* FIXME - we need to add code here to detect a totally new
6782 * configuration, reset the AP, unassoc, rxon timing, assoc,
6783 * clear sta table, add BCAST sta... */
6787 static int iwl3945_mac_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb);
6789 static int iwl3945_mac_config_interface(struct ieee80211_hw *hw,
6790 struct ieee80211_vif *vif,
6791 struct ieee80211_if_conf *conf)
6793 struct iwl3945_priv *priv = hw->priv;
6794 DECLARE_MAC_BUF(mac);
6795 unsigned long flags;
6801 if (priv->vif != vif) {
6802 IWL_DEBUG_MAC80211("leave - priv->vif != vif\n");
6806 /* handle this temporarily here */
6807 if (priv->iw_mode == NL80211_IFTYPE_ADHOC &&
6808 conf->changed & IEEE80211_IFCC_BEACON) {
6809 struct sk_buff *beacon = ieee80211_beacon_get(hw, vif);
6812 rc = iwl3945_mac_beacon_update(hw, beacon);
6817 /* XXX: this MUST use conf->mac_addr */
6819 if ((priv->iw_mode == NL80211_IFTYPE_AP) &&
6820 (!conf->ssid_len)) {
6822 ("Leaving in AP mode because HostAPD is not ready.\n");
6826 if (!iwl3945_is_alive(priv))
6829 mutex_lock(&priv->mutex);
6832 IWL_DEBUG_MAC80211("bssid: %s\n",
6833 print_mac(mac, conf->bssid));
6836 * very dubious code was here; the probe filtering flag is never set:
6838 if (unlikely(test_bit(STATUS_SCANNING, &priv->status)) &&
6839 !(priv->hw->flags & IEEE80211_HW_NO_PROBE_FILTERING)) {
6842 if (priv->iw_mode == NL80211_IFTYPE_AP) {
6844 conf->bssid = priv->mac_addr;
6845 memcpy(priv->bssid, priv->mac_addr, ETH_ALEN);
6846 IWL_DEBUG_MAC80211("bssid was set to: %s\n",
6847 print_mac(mac, conf->bssid));
6849 if (priv->ibss_beacon)
6850 dev_kfree_skb(priv->ibss_beacon);
6852 priv->ibss_beacon = ieee80211_beacon_get(hw, vif);
6855 if (iwl3945_is_rfkill(priv))
6858 if (conf->bssid && !is_zero_ether_addr(conf->bssid) &&
6859 !is_multicast_ether_addr(conf->bssid)) {
6860 /* If there is currently a HW scan going on in the background
6861 * then we need to cancel it else the RXON below will fail. */
6862 if (iwl3945_scan_cancel_timeout(priv, 100)) {
6863 IWL_WARNING("Aborted scan still in progress "
6865 IWL_DEBUG_MAC80211("leaving - scan abort failed.\n");
6866 mutex_unlock(&priv->mutex);
6869 memcpy(priv->staging_rxon.bssid_addr, conf->bssid, ETH_ALEN);
6871 /* TODO: Audit driver for usage of these members and see
6872 * if mac80211 deprecates them (priv->bssid looks like it
6873 * shouldn't be there, but I haven't scanned the IBSS code
6874 * to verify) - jpk */
6875 memcpy(priv->bssid, conf->bssid, ETH_ALEN);
6877 if (priv->iw_mode == NL80211_IFTYPE_AP)
6878 iwl3945_config_ap(priv);
6880 rc = iwl3945_commit_rxon(priv);
6881 if ((priv->iw_mode == NL80211_IFTYPE_STATION) && rc)
6882 iwl3945_add_station(priv,
6883 priv->active_rxon.bssid_addr, 1, 0);
6887 iwl3945_scan_cancel_timeout(priv, 100);
6888 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
6889 iwl3945_commit_rxon(priv);
6893 spin_lock_irqsave(&priv->lock, flags);
6894 if (!conf->ssid_len)
6895 memset(priv->essid, 0, IW_ESSID_MAX_SIZE);
6897 memcpy(priv->essid, conf->ssid, conf->ssid_len);
6899 priv->essid_len = conf->ssid_len;
6900 spin_unlock_irqrestore(&priv->lock, flags);
6902 IWL_DEBUG_MAC80211("leave\n");
6903 mutex_unlock(&priv->mutex);
6908 static void iwl3945_configure_filter(struct ieee80211_hw *hw,
6909 unsigned int changed_flags,
6910 unsigned int *total_flags,
6911 int mc_count, struct dev_addr_list *mc_list)
6913 struct iwl3945_priv *priv = hw->priv;
6915 if (changed_flags & (*total_flags) & FIF_OTHER_BSS) {
6916 IWL_DEBUG_MAC80211("Enter: type %d (0x%x, 0x%x)\n",
6917 NL80211_IFTYPE_MONITOR,
6918 changed_flags, *total_flags);
6919 /* queue work 'cuz mac80211 is holding a lock which
6920 * prevents us from issuing (synchronous) f/w cmds */
6921 queue_work(priv->workqueue, &priv->set_monitor);
6923 *total_flags &= FIF_OTHER_BSS | FIF_ALLMULTI |
6924 FIF_BCN_PRBRESP_PROMISC | FIF_CONTROL;
6927 static void iwl3945_mac_remove_interface(struct ieee80211_hw *hw,
6928 struct ieee80211_if_init_conf *conf)
6930 struct iwl3945_priv *priv = hw->priv;
6932 IWL_DEBUG_MAC80211("enter\n");
6934 mutex_lock(&priv->mutex);
6936 if (iwl3945_is_ready_rf(priv)) {
6937 iwl3945_scan_cancel_timeout(priv, 100);
6938 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
6939 iwl3945_commit_rxon(priv);
6941 if (priv->vif == conf->vif) {
6943 memset(priv->bssid, 0, ETH_ALEN);
6944 memset(priv->essid, 0, IW_ESSID_MAX_SIZE);
6945 priv->essid_len = 0;
6947 mutex_unlock(&priv->mutex);
6949 IWL_DEBUG_MAC80211("leave\n");
6952 #define IWL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6)
6954 static void iwl3945_bss_info_changed(struct ieee80211_hw *hw,
6955 struct ieee80211_vif *vif,
6956 struct ieee80211_bss_conf *bss_conf,
6959 struct iwl3945_priv *priv = hw->priv;
6961 IWL_DEBUG_MAC80211("changes = 0x%X\n", changes);
6963 if (changes & BSS_CHANGED_ERP_PREAMBLE) {
6964 IWL_DEBUG_MAC80211("ERP_PREAMBLE %d\n",
6965 bss_conf->use_short_preamble);
6966 if (bss_conf->use_short_preamble)
6967 priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
6969 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
6972 if (changes & BSS_CHANGED_ERP_CTS_PROT) {
6973 IWL_DEBUG_MAC80211("ERP_CTS %d\n", bss_conf->use_cts_prot);
6974 if (bss_conf->use_cts_prot && (priv->band != IEEE80211_BAND_5GHZ))
6975 priv->staging_rxon.flags |= RXON_FLG_TGG_PROTECT_MSK;
6977 priv->staging_rxon.flags &= ~RXON_FLG_TGG_PROTECT_MSK;
6980 if (changes & BSS_CHANGED_ASSOC) {
6981 IWL_DEBUG_MAC80211("ASSOC %d\n", bss_conf->assoc);
6982 /* This should never happen as this function should
6983 * never be called from interrupt context. */
6984 if (WARN_ON_ONCE(in_interrupt()))
6986 if (bss_conf->assoc) {
6987 priv->assoc_id = bss_conf->aid;
6988 priv->beacon_int = bss_conf->beacon_int;
6989 priv->timestamp0 = bss_conf->timestamp & 0xFFFFFFFF;
6990 priv->timestamp1 = (bss_conf->timestamp >> 32) &
6992 priv->assoc_capability = bss_conf->assoc_capability;
6993 priv->next_scan_jiffies = jiffies +
6994 IWL_DELAY_NEXT_SCAN_AFTER_ASSOC;
6995 mutex_lock(&priv->mutex);
6996 iwl3945_post_associate(priv);
6997 mutex_unlock(&priv->mutex);
7000 IWL_DEBUG_MAC80211("DISASSOC %d\n", bss_conf->assoc);
7002 } else if (changes && iwl3945_is_associated(priv) && priv->assoc_id) {
7003 IWL_DEBUG_MAC80211("Associated Changes %d\n", changes);
7004 iwl3945_send_rxon_assoc(priv);
7009 static int iwl3945_mac_hw_scan(struct ieee80211_hw *hw, u8 *ssid, size_t len)
7012 unsigned long flags;
7013 struct iwl3945_priv *priv = hw->priv;
7015 IWL_DEBUG_MAC80211("enter\n");
7017 mutex_lock(&priv->mutex);
7018 spin_lock_irqsave(&priv->lock, flags);
7020 if (!iwl3945_is_ready_rf(priv)) {
7022 IWL_DEBUG_MAC80211("leave - not ready or exit pending\n");
7026 if (priv->iw_mode == NL80211_IFTYPE_AP) { /* APs don't scan */
7028 IWL_ERROR("ERROR: APs don't scan\n");
7032 /* we don't schedule scan within next_scan_jiffies period */
7033 if (priv->next_scan_jiffies &&
7034 time_after(priv->next_scan_jiffies, jiffies)) {
7038 /* if we just finished scan ask for delay for a broadcast scan */
7039 if ((len == 0) && priv->last_scan_jiffies &&
7040 time_after(priv->last_scan_jiffies + IWL_DELAY_NEXT_SCAN,
7046 IWL_DEBUG_SCAN("direct scan for %s [%d]\n ",
7047 iwl3945_escape_essid(ssid, len), (int)len);
7049 priv->one_direct_scan = 1;
7050 priv->direct_ssid_len = (u8)
7051 min((u8) len, (u8) IW_ESSID_MAX_SIZE);
7052 memcpy(priv->direct_ssid, ssid, priv->direct_ssid_len);
7054 priv->one_direct_scan = 0;
7056 rc = iwl3945_scan_initiate(priv);
7058 IWL_DEBUG_MAC80211("leave\n");
7061 spin_unlock_irqrestore(&priv->lock, flags);
7062 mutex_unlock(&priv->mutex);
7067 static int iwl3945_mac_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
7068 const u8 *local_addr, const u8 *addr,
7069 struct ieee80211_key_conf *key)
7071 struct iwl3945_priv *priv = hw->priv;
7075 IWL_DEBUG_MAC80211("enter\n");
7077 if (!iwl3945_param_hwcrypto) {
7078 IWL_DEBUG_MAC80211("leave - hwcrypto disabled\n");
7082 if (is_zero_ether_addr(addr))
7083 /* only support pairwise keys */
7086 sta_id = iwl3945_hw_find_station(priv, addr);
7087 if (sta_id == IWL_INVALID_STATION) {
7088 DECLARE_MAC_BUF(mac);
7090 IWL_DEBUG_MAC80211("leave - %s not in station map.\n",
7091 print_mac(mac, addr));
7095 mutex_lock(&priv->mutex);
7097 iwl3945_scan_cancel_timeout(priv, 100);
7101 rc = iwl3945_update_sta_key_info(priv, key, sta_id);
7103 iwl3945_set_rxon_hwcrypto(priv, 1);
7104 iwl3945_commit_rxon(priv);
7105 key->hw_key_idx = sta_id;
7106 IWL_DEBUG_MAC80211("set_key success, using hwcrypto\n");
7107 key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
7111 rc = iwl3945_clear_sta_key_info(priv, sta_id);
7113 iwl3945_set_rxon_hwcrypto(priv, 0);
7114 iwl3945_commit_rxon(priv);
7115 IWL_DEBUG_MAC80211("disable hwcrypto key\n");
7122 IWL_DEBUG_MAC80211("leave\n");
7123 mutex_unlock(&priv->mutex);
7128 static int iwl3945_mac_conf_tx(struct ieee80211_hw *hw, u16 queue,
7129 const struct ieee80211_tx_queue_params *params)
7131 struct iwl3945_priv *priv = hw->priv;
7132 unsigned long flags;
7135 IWL_DEBUG_MAC80211("enter\n");
7137 if (!iwl3945_is_ready_rf(priv)) {
7138 IWL_DEBUG_MAC80211("leave - RF not ready\n");
7142 if (queue >= AC_NUM) {
7143 IWL_DEBUG_MAC80211("leave - queue >= AC_NUM %d\n", queue);
7147 if (!priv->qos_data.qos_enable) {
7148 priv->qos_data.qos_active = 0;
7149 IWL_DEBUG_MAC80211("leave - qos not enabled\n");
7152 q = AC_NUM - 1 - queue;
7154 spin_lock_irqsave(&priv->lock, flags);
7156 priv->qos_data.def_qos_parm.ac[q].cw_min = cpu_to_le16(params->cw_min);
7157 priv->qos_data.def_qos_parm.ac[q].cw_max = cpu_to_le16(params->cw_max);
7158 priv->qos_data.def_qos_parm.ac[q].aifsn = params->aifs;
7159 priv->qos_data.def_qos_parm.ac[q].edca_txop =
7160 cpu_to_le16((params->txop * 32));
7162 priv->qos_data.def_qos_parm.ac[q].reserved1 = 0;
7163 priv->qos_data.qos_active = 1;
7165 spin_unlock_irqrestore(&priv->lock, flags);
7167 mutex_lock(&priv->mutex);
7168 if (priv->iw_mode == NL80211_IFTYPE_AP)
7169 iwl3945_activate_qos(priv, 1);
7170 else if (priv->assoc_id && iwl3945_is_associated(priv))
7171 iwl3945_activate_qos(priv, 0);
7173 mutex_unlock(&priv->mutex);
7175 IWL_DEBUG_MAC80211("leave\n");
7179 static int iwl3945_mac_get_tx_stats(struct ieee80211_hw *hw,
7180 struct ieee80211_tx_queue_stats *stats)
7182 struct iwl3945_priv *priv = hw->priv;
7184 struct iwl3945_tx_queue *txq;
7185 struct iwl3945_queue *q;
7186 unsigned long flags;
7188 IWL_DEBUG_MAC80211("enter\n");
7190 if (!iwl3945_is_ready_rf(priv)) {
7191 IWL_DEBUG_MAC80211("leave - RF not ready\n");
7195 spin_lock_irqsave(&priv->lock, flags);
7197 for (i = 0; i < AC_NUM; i++) {
7198 txq = &priv->txq[i];
7200 avail = iwl3945_queue_space(q);
7202 stats[i].len = q->n_window - avail;
7203 stats[i].limit = q->n_window - q->high_mark;
7204 stats[i].count = q->n_window;
7207 spin_unlock_irqrestore(&priv->lock, flags);
7209 IWL_DEBUG_MAC80211("leave\n");
7214 static int iwl3945_mac_get_stats(struct ieee80211_hw *hw,
7215 struct ieee80211_low_level_stats *stats)
7217 IWL_DEBUG_MAC80211("enter\n");
7218 IWL_DEBUG_MAC80211("leave\n");
7223 static u64 iwl3945_mac_get_tsf(struct ieee80211_hw *hw)
7225 IWL_DEBUG_MAC80211("enter\n");
7226 IWL_DEBUG_MAC80211("leave\n");
7231 static void iwl3945_mac_reset_tsf(struct ieee80211_hw *hw)
7233 struct iwl3945_priv *priv = hw->priv;
7234 unsigned long flags;
7236 mutex_lock(&priv->mutex);
7237 IWL_DEBUG_MAC80211("enter\n");
7239 iwl3945_reset_qos(priv);
7241 spin_lock_irqsave(&priv->lock, flags);
7243 priv->assoc_capability = 0;
7244 priv->call_post_assoc_from_beacon = 0;
7246 /* new association get rid of ibss beacon skb */
7247 if (priv->ibss_beacon)
7248 dev_kfree_skb(priv->ibss_beacon);
7250 priv->ibss_beacon = NULL;
7252 priv->beacon_int = priv->hw->conf.beacon_int;
7253 priv->timestamp1 = 0;
7254 priv->timestamp0 = 0;
7255 if ((priv->iw_mode == NL80211_IFTYPE_STATION))
7256 priv->beacon_int = 0;
7258 spin_unlock_irqrestore(&priv->lock, flags);
7260 if (!iwl3945_is_ready_rf(priv)) {
7261 IWL_DEBUG_MAC80211("leave - not ready\n");
7262 mutex_unlock(&priv->mutex);
7266 /* we are restarting association process
7267 * clear RXON_FILTER_ASSOC_MSK bit
7269 if (priv->iw_mode != NL80211_IFTYPE_AP) {
7270 iwl3945_scan_cancel_timeout(priv, 100);
7271 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
7272 iwl3945_commit_rxon(priv);
7275 /* Per mac80211.h: This is only used in IBSS mode... */
7276 if (priv->iw_mode != NL80211_IFTYPE_ADHOC) {
7278 IWL_DEBUG_MAC80211("leave - not in IBSS\n");
7279 mutex_unlock(&priv->mutex);
7283 iwl3945_set_rate(priv);
7285 mutex_unlock(&priv->mutex);
7287 IWL_DEBUG_MAC80211("leave\n");
7291 static int iwl3945_mac_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb)
7293 struct iwl3945_priv *priv = hw->priv;
7294 unsigned long flags;
7296 mutex_lock(&priv->mutex);
7297 IWL_DEBUG_MAC80211("enter\n");
7299 if (!iwl3945_is_ready_rf(priv)) {
7300 IWL_DEBUG_MAC80211("leave - RF not ready\n");
7301 mutex_unlock(&priv->mutex);
7305 if (priv->iw_mode != NL80211_IFTYPE_ADHOC) {
7306 IWL_DEBUG_MAC80211("leave - not IBSS\n");
7307 mutex_unlock(&priv->mutex);
7311 spin_lock_irqsave(&priv->lock, flags);
7313 if (priv->ibss_beacon)
7314 dev_kfree_skb(priv->ibss_beacon);
7316 priv->ibss_beacon = skb;
7320 IWL_DEBUG_MAC80211("leave\n");
7321 spin_unlock_irqrestore(&priv->lock, flags);
7323 iwl3945_reset_qos(priv);
7325 iwl3945_post_associate(priv);
7327 mutex_unlock(&priv->mutex);
7332 /*****************************************************************************
7336 *****************************************************************************/
7338 #ifdef CONFIG_IWL3945_DEBUG
7341 * The following adds a new attribute to the sysfs representation
7342 * of this device driver (i.e. a new file in /sys/bus/pci/drivers/iwl/)
7343 * used for controlling the debug level.
7345 * See the level definitions in iwl for details.
7348 static ssize_t show_debug_level(struct device_driver *d, char *buf)
7350 return sprintf(buf, "0x%08X\n", iwl3945_debug_level);
7352 static ssize_t store_debug_level(struct device_driver *d,
7353 const char *buf, size_t count)
7355 char *p = (char *)buf;
7358 val = simple_strtoul(p, &p, 0);
7360 printk(KERN_INFO DRV_NAME
7361 ": %s is not in hex or decimal form.\n", buf);
7363 iwl3945_debug_level = val;
7365 return strnlen(buf, count);
7368 static DRIVER_ATTR(debug_level, S_IWUSR | S_IRUGO,
7369 show_debug_level, store_debug_level);
7371 #endif /* CONFIG_IWL3945_DEBUG */
7373 static ssize_t show_temperature(struct device *d,
7374 struct device_attribute *attr, char *buf)
7376 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7378 if (!iwl3945_is_alive(priv))
7381 return sprintf(buf, "%d\n", iwl3945_hw_get_temperature(priv));
7384 static DEVICE_ATTR(temperature, S_IRUGO, show_temperature, NULL);
7386 static ssize_t show_tx_power(struct device *d,
7387 struct device_attribute *attr, char *buf)
7389 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7390 return sprintf(buf, "%d\n", priv->user_txpower_limit);
7393 static ssize_t store_tx_power(struct device *d,
7394 struct device_attribute *attr,
7395 const char *buf, size_t count)
7397 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7398 char *p = (char *)buf;
7401 val = simple_strtoul(p, &p, 10);
7403 printk(KERN_INFO DRV_NAME
7404 ": %s is not in decimal form.\n", buf);
7406 iwl3945_hw_reg_set_txpower(priv, val);
7411 static DEVICE_ATTR(tx_power, S_IWUSR | S_IRUGO, show_tx_power, store_tx_power);
7413 static ssize_t show_flags(struct device *d,
7414 struct device_attribute *attr, char *buf)
7416 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7418 return sprintf(buf, "0x%04X\n", priv->active_rxon.flags);
7421 static ssize_t store_flags(struct device *d,
7422 struct device_attribute *attr,
7423 const char *buf, size_t count)
7425 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7426 u32 flags = simple_strtoul(buf, NULL, 0);
7428 mutex_lock(&priv->mutex);
7429 if (le32_to_cpu(priv->staging_rxon.flags) != flags) {
7430 /* Cancel any currently running scans... */
7431 if (iwl3945_scan_cancel_timeout(priv, 100))
7432 IWL_WARNING("Could not cancel scan.\n");
7434 IWL_DEBUG_INFO("Committing rxon.flags = 0x%04X\n",
7436 priv->staging_rxon.flags = cpu_to_le32(flags);
7437 iwl3945_commit_rxon(priv);
7440 mutex_unlock(&priv->mutex);
7445 static DEVICE_ATTR(flags, S_IWUSR | S_IRUGO, show_flags, store_flags);
7447 static ssize_t show_filter_flags(struct device *d,
7448 struct device_attribute *attr, char *buf)
7450 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7452 return sprintf(buf, "0x%04X\n",
7453 le32_to_cpu(priv->active_rxon.filter_flags));
7456 static ssize_t store_filter_flags(struct device *d,
7457 struct device_attribute *attr,
7458 const char *buf, size_t count)
7460 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7461 u32 filter_flags = simple_strtoul(buf, NULL, 0);
7463 mutex_lock(&priv->mutex);
7464 if (le32_to_cpu(priv->staging_rxon.filter_flags) != filter_flags) {
7465 /* Cancel any currently running scans... */
7466 if (iwl3945_scan_cancel_timeout(priv, 100))
7467 IWL_WARNING("Could not cancel scan.\n");
7469 IWL_DEBUG_INFO("Committing rxon.filter_flags = "
7470 "0x%04X\n", filter_flags);
7471 priv->staging_rxon.filter_flags =
7472 cpu_to_le32(filter_flags);
7473 iwl3945_commit_rxon(priv);
7476 mutex_unlock(&priv->mutex);
7481 static DEVICE_ATTR(filter_flags, S_IWUSR | S_IRUGO, show_filter_flags,
7482 store_filter_flags);
7484 #ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT
7486 static ssize_t show_measurement(struct device *d,
7487 struct device_attribute *attr, char *buf)
7489 struct iwl3945_priv *priv = dev_get_drvdata(d);
7490 struct iwl3945_spectrum_notification measure_report;
7491 u32 size = sizeof(measure_report), len = 0, ofs = 0;
7492 u8 *data = (u8 *)&measure_report;
7493 unsigned long flags;
7495 spin_lock_irqsave(&priv->lock, flags);
7496 if (!(priv->measurement_status & MEASUREMENT_READY)) {
7497 spin_unlock_irqrestore(&priv->lock, flags);
7500 memcpy(&measure_report, &priv->measure_report, size);
7501 priv->measurement_status = 0;
7502 spin_unlock_irqrestore(&priv->lock, flags);
7504 while (size && (PAGE_SIZE - len)) {
7505 hex_dump_to_buffer(data + ofs, size, 16, 1, buf + len,
7506 PAGE_SIZE - len, 1);
7508 if (PAGE_SIZE - len)
7512 size -= min(size, 16U);
7518 static ssize_t store_measurement(struct device *d,
7519 struct device_attribute *attr,
7520 const char *buf, size_t count)
7522 struct iwl3945_priv *priv = dev_get_drvdata(d);
7523 struct ieee80211_measurement_params params = {
7524 .channel = le16_to_cpu(priv->active_rxon.channel),
7525 .start_time = cpu_to_le64(priv->last_tsf),
7526 .duration = cpu_to_le16(1),
7528 u8 type = IWL_MEASURE_BASIC;
7534 strncpy(buffer, buf, min(sizeof(buffer), count));
7535 channel = simple_strtoul(p, NULL, 0);
7537 params.channel = channel;
7540 while (*p && *p != ' ')
7543 type = simple_strtoul(p + 1, NULL, 0);
7546 IWL_DEBUG_INFO("Invoking measurement of type %d on "
7547 "channel %d (for '%s')\n", type, params.channel, buf);
7548 iwl3945_get_measurement(priv, ¶ms, type);
7553 static DEVICE_ATTR(measurement, S_IRUSR | S_IWUSR,
7554 show_measurement, store_measurement);
7555 #endif /* CONFIG_IWL3945_SPECTRUM_MEASUREMENT */
7557 static ssize_t store_retry_rate(struct device *d,
7558 struct device_attribute *attr,
7559 const char *buf, size_t count)
7561 struct iwl3945_priv *priv = dev_get_drvdata(d);
7563 priv->retry_rate = simple_strtoul(buf, NULL, 0);
7564 if (priv->retry_rate <= 0)
7565 priv->retry_rate = 1;
7570 static ssize_t show_retry_rate(struct device *d,
7571 struct device_attribute *attr, char *buf)
7573 struct iwl3945_priv *priv = dev_get_drvdata(d);
7574 return sprintf(buf, "%d", priv->retry_rate);
7577 static DEVICE_ATTR(retry_rate, S_IWUSR | S_IRUSR, show_retry_rate,
7580 static ssize_t store_power_level(struct device *d,
7581 struct device_attribute *attr,
7582 const char *buf, size_t count)
7584 struct iwl3945_priv *priv = dev_get_drvdata(d);
7588 mode = simple_strtoul(buf, NULL, 0);
7589 mutex_lock(&priv->mutex);
7591 if (!iwl3945_is_ready(priv)) {
7596 if ((mode < 1) || (mode > IWL_POWER_LIMIT) || (mode == IWL_POWER_AC))
7597 mode = IWL_POWER_AC;
7599 mode |= IWL_POWER_ENABLED;
7601 if (mode != priv->power_mode) {
7602 rc = iwl3945_send_power_mode(priv, IWL_POWER_LEVEL(mode));
7604 IWL_DEBUG_MAC80211("failed setting power mode.\n");
7607 priv->power_mode = mode;
7613 mutex_unlock(&priv->mutex);
7617 #define MAX_WX_STRING 80
7619 /* Values are in microsecond */
7620 static const s32 timeout_duration[] = {
7627 static const s32 period_duration[] = {
7635 static ssize_t show_power_level(struct device *d,
7636 struct device_attribute *attr, char *buf)
7638 struct iwl3945_priv *priv = dev_get_drvdata(d);
7639 int level = IWL_POWER_LEVEL(priv->power_mode);
7642 p += sprintf(p, "%d ", level);
7644 case IWL_POWER_MODE_CAM:
7646 p += sprintf(p, "(AC)");
7648 case IWL_POWER_BATTERY:
7649 p += sprintf(p, "(BATTERY)");
7653 "(Timeout %dms, Period %dms)",
7654 timeout_duration[level - 1] / 1000,
7655 period_duration[level - 1] / 1000);
7658 if (!(priv->power_mode & IWL_POWER_ENABLED))
7659 p += sprintf(p, " OFF\n");
7661 p += sprintf(p, " \n");
7667 static DEVICE_ATTR(power_level, S_IWUSR | S_IRUSR, show_power_level,
7670 static ssize_t show_channels(struct device *d,
7671 struct device_attribute *attr, char *buf)
7673 /* all this shit doesn't belong into sysfs anyway */
7677 static DEVICE_ATTR(channels, S_IRUSR, show_channels, NULL);
7679 static ssize_t show_statistics(struct device *d,
7680 struct device_attribute *attr, char *buf)
7682 struct iwl3945_priv *priv = dev_get_drvdata(d);
7683 u32 size = sizeof(struct iwl3945_notif_statistics);
7684 u32 len = 0, ofs = 0;
7685 u8 *data = (u8 *)&priv->statistics;
7688 if (!iwl3945_is_alive(priv))
7691 mutex_lock(&priv->mutex);
7692 rc = iwl3945_send_statistics_request(priv);
7693 mutex_unlock(&priv->mutex);
7697 "Error sending statistics request: 0x%08X\n", rc);
7701 while (size && (PAGE_SIZE - len)) {
7702 hex_dump_to_buffer(data + ofs, size, 16, 1, buf + len,
7703 PAGE_SIZE - len, 1);
7705 if (PAGE_SIZE - len)
7709 size -= min(size, 16U);
7715 static DEVICE_ATTR(statistics, S_IRUGO, show_statistics, NULL);
7717 static ssize_t show_antenna(struct device *d,
7718 struct device_attribute *attr, char *buf)
7720 struct iwl3945_priv *priv = dev_get_drvdata(d);
7722 if (!iwl3945_is_alive(priv))
7725 return sprintf(buf, "%d\n", priv->antenna);
7728 static ssize_t store_antenna(struct device *d,
7729 struct device_attribute *attr,
7730 const char *buf, size_t count)
7733 struct iwl3945_priv *priv = dev_get_drvdata(d);
7738 if (sscanf(buf, "%1i", &ant) != 1) {
7739 IWL_DEBUG_INFO("not in hex or decimal form.\n");
7743 if ((ant >= 0) && (ant <= 2)) {
7744 IWL_DEBUG_INFO("Setting antenna select to %d.\n", ant);
7745 priv->antenna = (enum iwl3945_antenna)ant;
7747 IWL_DEBUG_INFO("Bad antenna select value %d.\n", ant);
7753 static DEVICE_ATTR(antenna, S_IWUSR | S_IRUGO, show_antenna, store_antenna);
7755 static ssize_t show_status(struct device *d,
7756 struct device_attribute *attr, char *buf)
7758 struct iwl3945_priv *priv = (struct iwl3945_priv *)d->driver_data;
7759 if (!iwl3945_is_alive(priv))
7761 return sprintf(buf, "0x%08x\n", (int)priv->status);
7764 static DEVICE_ATTR(status, S_IRUGO, show_status, NULL);
7766 static ssize_t dump_error_log(struct device *d,
7767 struct device_attribute *attr,
7768 const char *buf, size_t count)
7770 char *p = (char *)buf;
7773 iwl3945_dump_nic_error_log((struct iwl3945_priv *)d->driver_data);
7775 return strnlen(buf, count);
7778 static DEVICE_ATTR(dump_errors, S_IWUSR, NULL, dump_error_log);
7780 static ssize_t dump_event_log(struct device *d,
7781 struct device_attribute *attr,
7782 const char *buf, size_t count)
7784 char *p = (char *)buf;
7787 iwl3945_dump_nic_event_log((struct iwl3945_priv *)d->driver_data);
7789 return strnlen(buf, count);
7792 static DEVICE_ATTR(dump_events, S_IWUSR, NULL, dump_event_log);
7794 /*****************************************************************************
7796 * driver setup and teardown
7798 *****************************************************************************/
7800 static void iwl3945_setup_deferred_work(struct iwl3945_priv *priv)
7802 priv->workqueue = create_workqueue(DRV_NAME);
7804 init_waitqueue_head(&priv->wait_command_queue);
7806 INIT_WORK(&priv->up, iwl3945_bg_up);
7807 INIT_WORK(&priv->restart, iwl3945_bg_restart);
7808 INIT_WORK(&priv->rx_replenish, iwl3945_bg_rx_replenish);
7809 INIT_WORK(&priv->scan_completed, iwl3945_bg_scan_completed);
7810 INIT_WORK(&priv->request_scan, iwl3945_bg_request_scan);
7811 INIT_WORK(&priv->abort_scan, iwl3945_bg_abort_scan);
7812 INIT_WORK(&priv->rf_kill, iwl3945_bg_rf_kill);
7813 INIT_WORK(&priv->beacon_update, iwl3945_bg_beacon_update);
7814 INIT_WORK(&priv->set_monitor, iwl3945_bg_set_monitor);
7815 INIT_DELAYED_WORK(&priv->init_alive_start, iwl3945_bg_init_alive_start);
7816 INIT_DELAYED_WORK(&priv->alive_start, iwl3945_bg_alive_start);
7817 INIT_DELAYED_WORK(&priv->scan_check, iwl3945_bg_scan_check);
7819 iwl3945_hw_setup_deferred_work(priv);
7821 tasklet_init(&priv->irq_tasklet, (void (*)(unsigned long))
7822 iwl3945_irq_tasklet, (unsigned long)priv);
7825 static void iwl3945_cancel_deferred_work(struct iwl3945_priv *priv)
7827 iwl3945_hw_cancel_deferred_work(priv);
7829 cancel_delayed_work_sync(&priv->init_alive_start);
7830 cancel_delayed_work(&priv->scan_check);
7831 cancel_delayed_work(&priv->alive_start);
7832 cancel_work_sync(&priv->beacon_update);
7835 static struct attribute *iwl3945_sysfs_entries[] = {
7836 &dev_attr_antenna.attr,
7837 &dev_attr_channels.attr,
7838 &dev_attr_dump_errors.attr,
7839 &dev_attr_dump_events.attr,
7840 &dev_attr_flags.attr,
7841 &dev_attr_filter_flags.attr,
7842 #ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT
7843 &dev_attr_measurement.attr,
7845 &dev_attr_power_level.attr,
7846 &dev_attr_retry_rate.attr,
7847 &dev_attr_statistics.attr,
7848 &dev_attr_status.attr,
7849 &dev_attr_temperature.attr,
7850 &dev_attr_tx_power.attr,
7855 static struct attribute_group iwl3945_attribute_group = {
7856 .name = NULL, /* put in device directory */
7857 .attrs = iwl3945_sysfs_entries,
7860 static struct ieee80211_ops iwl3945_hw_ops = {
7861 .tx = iwl3945_mac_tx,
7862 .start = iwl3945_mac_start,
7863 .stop = iwl3945_mac_stop,
7864 .add_interface = iwl3945_mac_add_interface,
7865 .remove_interface = iwl3945_mac_remove_interface,
7866 .config = iwl3945_mac_config,
7867 .config_interface = iwl3945_mac_config_interface,
7868 .configure_filter = iwl3945_configure_filter,
7869 .set_key = iwl3945_mac_set_key,
7870 .get_stats = iwl3945_mac_get_stats,
7871 .get_tx_stats = iwl3945_mac_get_tx_stats,
7872 .conf_tx = iwl3945_mac_conf_tx,
7873 .get_tsf = iwl3945_mac_get_tsf,
7874 .reset_tsf = iwl3945_mac_reset_tsf,
7875 .bss_info_changed = iwl3945_bss_info_changed,
7876 .hw_scan = iwl3945_mac_hw_scan
7879 static int iwl3945_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
7882 struct iwl3945_priv *priv;
7883 struct ieee80211_hw *hw;
7884 struct iwl_3945_cfg *cfg = (struct iwl_3945_cfg *)(ent->driver_data);
7885 unsigned long flags;
7886 DECLARE_MAC_BUF(mac);
7888 /* Disabling hardware scan means that mac80211 will perform scans
7889 * "the hard way", rather than using device's scan. */
7890 if (iwl3945_param_disable_hw_scan) {
7891 IWL_DEBUG_INFO("Disabling hw_scan\n");
7892 iwl3945_hw_ops.hw_scan = NULL;
7895 if ((iwl3945_param_queues_num > IWL39_MAX_NUM_QUEUES) ||
7896 (iwl3945_param_queues_num < IWL_MIN_NUM_QUEUES)) {
7897 IWL_ERROR("invalid queues_num, should be between %d and %d\n",
7898 IWL_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES);
7903 /* mac80211 allocates memory for this device instance, including
7904 * space for this driver's private structure */
7905 hw = ieee80211_alloc_hw(sizeof(struct iwl3945_priv), &iwl3945_hw_ops);
7907 IWL_ERROR("Can not allocate network device\n");
7911 SET_IEEE80211_DEV(hw, &pdev->dev);
7913 hw->rate_control_algorithm = "iwl-3945-rs";
7914 hw->sta_data_size = sizeof(struct iwl3945_sta_priv);
7916 IWL_DEBUG_INFO("*** LOAD DRIVER ***\n");
7920 priv->pci_dev = pdev;
7923 /* Select antenna (may be helpful if only one antenna is connected) */
7924 priv->antenna = (enum iwl3945_antenna)iwl3945_param_antenna;
7925 #ifdef CONFIG_IWL3945_DEBUG
7926 iwl3945_debug_level = iwl3945_param_debug;
7927 atomic_set(&priv->restrict_refcnt, 0);
7929 priv->retry_rate = 1;
7931 priv->ibss_beacon = NULL;
7933 /* Tell mac80211 our characteristics */
7934 hw->flags = IEEE80211_HW_SIGNAL_DBM |
7935 IEEE80211_HW_NOISE_DBM;
7937 hw->wiphy->interface_modes =
7938 BIT(NL80211_IFTYPE_AP) |
7939 BIT(NL80211_IFTYPE_STATION) |
7940 BIT(NL80211_IFTYPE_ADHOC);
7942 /* 4 EDCA QOS priorities */
7945 spin_lock_init(&priv->lock);
7946 spin_lock_init(&priv->power_data.lock);
7947 spin_lock_init(&priv->sta_lock);
7948 spin_lock_init(&priv->hcmd_lock);
7950 INIT_LIST_HEAD(&priv->free_frames);
7952 mutex_init(&priv->mutex);
7953 if (pci_enable_device(pdev)) {
7955 goto out_ieee80211_free_hw;
7958 pci_set_master(pdev);
7960 /* Clear the driver's (not device's) station table */
7961 iwl3945_clear_stations_table(priv);
7963 priv->data_retry_limit = -1;
7964 priv->ieee_channels = NULL;
7965 priv->ieee_rates = NULL;
7966 priv->band = IEEE80211_BAND_2GHZ;
7968 err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
7970 err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
7972 printk(KERN_WARNING DRV_NAME ": No suitable DMA available.\n");
7973 goto out_pci_disable_device;
7976 pci_set_drvdata(pdev, priv);
7977 err = pci_request_regions(pdev, DRV_NAME);
7979 goto out_pci_disable_device;
7981 /* We disable the RETRY_TIMEOUT register (0x41) to keep
7982 * PCI Tx retries from interfering with C3 CPU state */
7983 pci_write_config_byte(pdev, 0x41, 0x00);
7985 priv->hw_base = pci_iomap(pdev, 0, 0);
7986 if (!priv->hw_base) {
7988 goto out_pci_release_regions;
7991 IWL_DEBUG_INFO("pci_resource_len = 0x%08llx\n",
7992 (unsigned long long) pci_resource_len(pdev, 0));
7993 IWL_DEBUG_INFO("pci_resource_base = %p\n", priv->hw_base);
7995 /* Initialize module parameter values here */
7997 /* Disable radio (SW RF KILL) via parameter when loading driver */
7998 if (iwl3945_param_disable) {
7999 set_bit(STATUS_RF_KILL_SW, &priv->status);
8000 IWL_DEBUG_INFO("Radio disabled.\n");
8003 priv->iw_mode = NL80211_IFTYPE_STATION;
8005 printk(KERN_INFO DRV_NAME
8006 ": Detected Intel Wireless WiFi Link %s\n", priv->cfg->name);
8008 /* Device-specific setup */
8009 if (iwl3945_hw_set_hw_setting(priv)) {
8010 IWL_ERROR("failed to set hw settings\n");
8014 if (iwl3945_param_qos_enable)
8015 priv->qos_data.qos_enable = 1;
8017 iwl3945_reset_qos(priv);
8019 priv->qos_data.qos_active = 0;
8020 priv->qos_data.qos_cap.val = 0;
8022 iwl3945_set_rxon_channel(priv, IEEE80211_BAND_2GHZ, 6);
8023 iwl3945_setup_deferred_work(priv);
8024 iwl3945_setup_rx_handlers(priv);
8026 priv->rates_mask = IWL_RATES_MASK;
8027 /* If power management is turned on, default to AC mode */
8028 priv->power_mode = IWL_POWER_AC;
8029 priv->user_txpower_limit = IWL_DEFAULT_TX_POWER;
8031 spin_lock_irqsave(&priv->lock, flags);
8032 iwl3945_disable_interrupts(priv);
8033 spin_unlock_irqrestore(&priv->lock, flags);
8035 err = sysfs_create_group(&pdev->dev.kobj, &iwl3945_attribute_group);
8037 IWL_ERROR("failed to create sysfs device attributes\n");
8038 goto out_release_irq;
8042 iwl3945_set_bit(priv, CSR_GIO_CHICKEN_BITS,
8043 CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER);
8045 iwl3945_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
8046 err = iwl3945_poll_bit(priv, CSR_GP_CNTRL,
8047 CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
8048 CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
8050 IWL_DEBUG_INFO("Failed to init the card\n");
8051 goto out_remove_sysfs;
8053 /* Read the EEPROM */
8054 err = iwl3945_eeprom_init(priv);
8056 IWL_ERROR("Unable to init EEPROM\n");
8057 goto out_remove_sysfs;
8059 /* MAC Address location in EEPROM same for 3945/4965 */
8060 get_eeprom_mac(priv, priv->mac_addr);
8061 IWL_DEBUG_INFO("MAC address: %s\n", print_mac(mac, priv->mac_addr));
8062 SET_IEEE80211_PERM_ADDR(priv->hw, priv->mac_addr);
8064 err = iwl3945_init_channel_map(priv);
8066 IWL_ERROR("initializing regulatory failed: %d\n", err);
8067 goto out_remove_sysfs;
8070 err = iwl3945_init_geos(priv);
8072 IWL_ERROR("initializing geos failed: %d\n", err);
8073 goto out_free_channel_map;
8076 err = ieee80211_register_hw(priv->hw);
8078 IWL_ERROR("Failed to register network device (error %d)\n", err);
8082 priv->hw->conf.beacon_int = 100;
8083 priv->mac80211_registered = 1;
8084 pci_save_state(pdev);
8085 pci_disable_device(pdev);
8087 err = iwl3945_rfkill_init(priv);
8089 IWL_ERROR("Unable to initialize RFKILL system. "
8090 "Ignoring error: %d\n", err);
8095 iwl3945_free_geos(priv);
8096 out_free_channel_map:
8097 iwl3945_free_channel_map(priv);
8099 sysfs_remove_group(&pdev->dev.kobj, &iwl3945_attribute_group);
8102 destroy_workqueue(priv->workqueue);
8103 priv->workqueue = NULL;
8104 iwl3945_unset_hw_setting(priv);
8107 pci_iounmap(pdev, priv->hw_base);
8108 out_pci_release_regions:
8109 pci_release_regions(pdev);
8110 out_pci_disable_device:
8111 pci_disable_device(pdev);
8112 pci_set_drvdata(pdev, NULL);
8113 out_ieee80211_free_hw:
8114 ieee80211_free_hw(priv->hw);
8119 static void __devexit iwl3945_pci_remove(struct pci_dev *pdev)
8121 struct iwl3945_priv *priv = pci_get_drvdata(pdev);
8122 unsigned long flags;
8127 IWL_DEBUG_INFO("*** UNLOAD DRIVER ***\n");
8129 set_bit(STATUS_EXIT_PENDING, &priv->status);
8133 /* make sure we flush any pending irq or
8134 * tasklet for the driver
8136 spin_lock_irqsave(&priv->lock, flags);
8137 iwl3945_disable_interrupts(priv);
8138 spin_unlock_irqrestore(&priv->lock, flags);
8140 iwl_synchronize_irq(priv);
8142 sysfs_remove_group(&pdev->dev.kobj, &iwl3945_attribute_group);
8144 iwl3945_rfkill_unregister(priv);
8145 iwl3945_dealloc_ucode_pci(priv);
8148 iwl3945_rx_queue_free(priv, &priv->rxq);
8149 iwl3945_hw_txq_ctx_free(priv);
8151 iwl3945_unset_hw_setting(priv);
8152 iwl3945_clear_stations_table(priv);
8154 if (priv->mac80211_registered)
8155 ieee80211_unregister_hw(priv->hw);
8157 /*netif_stop_queue(dev); */
8158 flush_workqueue(priv->workqueue);
8160 /* ieee80211_unregister_hw calls iwl3945_mac_stop, which flushes
8161 * priv->workqueue... so we can't take down the workqueue
8163 destroy_workqueue(priv->workqueue);
8164 priv->workqueue = NULL;
8166 pci_iounmap(pdev, priv->hw_base);
8167 pci_release_regions(pdev);
8168 pci_disable_device(pdev);
8169 pci_set_drvdata(pdev, NULL);
8171 iwl3945_free_channel_map(priv);
8172 iwl3945_free_geos(priv);
8174 if (priv->ibss_beacon)
8175 dev_kfree_skb(priv->ibss_beacon);
8177 ieee80211_free_hw(priv->hw);
8182 static int iwl3945_pci_suspend(struct pci_dev *pdev, pm_message_t state)
8184 struct iwl3945_priv *priv = pci_get_drvdata(pdev);
8186 if (priv->is_open) {
8187 set_bit(STATUS_IN_SUSPEND, &priv->status);
8188 iwl3945_mac_stop(priv->hw);
8192 pci_set_power_state(pdev, PCI_D3hot);
8197 static int iwl3945_pci_resume(struct pci_dev *pdev)
8199 struct iwl3945_priv *priv = pci_get_drvdata(pdev);
8201 pci_set_power_state(pdev, PCI_D0);
8204 iwl3945_mac_start(priv->hw);
8206 clear_bit(STATUS_IN_SUSPEND, &priv->status);
8210 #endif /* CONFIG_PM */
8212 /*************** RFKILL FUNCTIONS **********/
8213 #ifdef CONFIG_IWL3945_RFKILL
8214 /* software rf-kill from user */
8215 static int iwl3945_rfkill_soft_rf_kill(void *data, enum rfkill_state state)
8217 struct iwl3945_priv *priv = data;
8223 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
8226 IWL_DEBUG_RF_KILL("we recieved soft RFKILL set to state %d\n", state);
8227 mutex_lock(&priv->mutex);
8230 case RFKILL_STATE_UNBLOCKED:
8231 if (iwl3945_is_rfkill_hw(priv)) {
8235 iwl3945_radio_kill_sw(priv, 0);
8237 case RFKILL_STATE_SOFT_BLOCKED:
8238 iwl3945_radio_kill_sw(priv, 1);
8241 IWL_WARNING("we recieved unexpected RFKILL state %d\n", state);
8245 mutex_unlock(&priv->mutex);
8250 int iwl3945_rfkill_init(struct iwl3945_priv *priv)
8252 struct device *device = wiphy_dev(priv->hw->wiphy);
8255 BUG_ON(device == NULL);
8257 IWL_DEBUG_RF_KILL("Initializing RFKILL.\n");
8258 priv->rfkill = rfkill_allocate(device, RFKILL_TYPE_WLAN);
8259 if (!priv->rfkill) {
8260 IWL_ERROR("Unable to allocate rfkill device.\n");
8265 priv->rfkill->name = priv->cfg->name;
8266 priv->rfkill->data = priv;
8267 priv->rfkill->state = RFKILL_STATE_UNBLOCKED;
8268 priv->rfkill->toggle_radio = iwl3945_rfkill_soft_rf_kill;
8269 priv->rfkill->user_claim_unsupported = 1;
8271 priv->rfkill->dev.class->suspend = NULL;
8272 priv->rfkill->dev.class->resume = NULL;
8274 ret = rfkill_register(priv->rfkill);
8276 IWL_ERROR("Unable to register rfkill: %d\n", ret);
8280 IWL_DEBUG_RF_KILL("RFKILL initialization complete.\n");
8284 if (priv->rfkill != NULL)
8285 rfkill_free(priv->rfkill);
8286 priv->rfkill = NULL;
8289 IWL_DEBUG_RF_KILL("RFKILL initialization complete.\n");
8293 void iwl3945_rfkill_unregister(struct iwl3945_priv *priv)
8296 rfkill_unregister(priv->rfkill);
8298 priv->rfkill = NULL;
8301 /* set rf-kill to the right state. */
8302 void iwl3945_rfkill_set_hw_state(struct iwl3945_priv *priv)
8308 if (iwl3945_is_rfkill_hw(priv)) {
8309 rfkill_force_state(priv->rfkill, RFKILL_STATE_HARD_BLOCKED);
8313 if (!iwl3945_is_rfkill_sw(priv))
8314 rfkill_force_state(priv->rfkill, RFKILL_STATE_UNBLOCKED);
8316 rfkill_force_state(priv->rfkill, RFKILL_STATE_SOFT_BLOCKED);
8320 /*****************************************************************************
8322 * driver and module entry point
8324 *****************************************************************************/
8326 static struct pci_driver iwl3945_driver = {
8328 .id_table = iwl3945_hw_card_ids,
8329 .probe = iwl3945_pci_probe,
8330 .remove = __devexit_p(iwl3945_pci_remove),
8332 .suspend = iwl3945_pci_suspend,
8333 .resume = iwl3945_pci_resume,
8337 static int __init iwl3945_init(void)
8341 printk(KERN_INFO DRV_NAME ": " DRV_DESCRIPTION ", " DRV_VERSION "\n");
8342 printk(KERN_INFO DRV_NAME ": " DRV_COPYRIGHT "\n");
8344 ret = iwl3945_rate_control_register();
8346 IWL_ERROR("Unable to register rate control algorithm: %d\n", ret);
8350 ret = pci_register_driver(&iwl3945_driver);
8352 IWL_ERROR("Unable to initialize PCI module\n");
8353 goto error_register;
8355 #ifdef CONFIG_IWL3945_DEBUG
8356 ret = driver_create_file(&iwl3945_driver.driver, &driver_attr_debug_level);
8358 IWL_ERROR("Unable to create driver sysfs file\n");
8365 #ifdef CONFIG_IWL3945_DEBUG
8367 pci_unregister_driver(&iwl3945_driver);
8370 iwl3945_rate_control_unregister();
8374 static void __exit iwl3945_exit(void)
8376 #ifdef CONFIG_IWL3945_DEBUG
8377 driver_remove_file(&iwl3945_driver.driver, &driver_attr_debug_level);
8379 pci_unregister_driver(&iwl3945_driver);
8380 iwl3945_rate_control_unregister();
8383 MODULE_FIRMWARE("iwlwifi-3945" IWL3945_UCODE_API ".ucode");
8385 module_param_named(antenna, iwl3945_param_antenna, int, 0444);
8386 MODULE_PARM_DESC(antenna, "select antenna (1=Main, 2=Aux, default 0 [both])");
8387 module_param_named(disable, iwl3945_param_disable, int, 0444);
8388 MODULE_PARM_DESC(disable, "manually disable the radio (default 0 [radio on])");
8389 module_param_named(hwcrypto, iwl3945_param_hwcrypto, int, 0444);
8390 MODULE_PARM_DESC(hwcrypto,
8391 "using hardware crypto engine (default 0 [software])\n");
8392 module_param_named(debug, iwl3945_param_debug, int, 0444);
8393 MODULE_PARM_DESC(debug, "debug output mask");
8394 module_param_named(disable_hw_scan, iwl3945_param_disable_hw_scan, int, 0444);
8395 MODULE_PARM_DESC(disable_hw_scan, "disable hardware scanning (default 0)");
8397 module_param_named(queues_num, iwl3945_param_queues_num, int, 0444);
8398 MODULE_PARM_DESC(queues_num, "number of hw queues.");
8401 module_param_named(qos_enable, iwl3945_param_qos_enable, int, 0444);
8402 MODULE_PARM_DESC(qos_enable, "enable all QoS functionality");
8404 module_exit(iwl3945_exit);
8405 module_init(iwl3945_init);