4 * linux/include/linux/ide.h
6 * Copyright (C) 1994-2002 Linus Torvalds & authors
9 #include <linux/init.h>
10 #include <linux/ioport.h>
11 #include <linux/hdreg.h>
12 #include <linux/hdsmart.h>
13 #include <linux/blkdev.h>
14 #include <linux/proc_fs.h>
15 #include <linux/interrupt.h>
16 #include <linux/bitops.h>
17 #include <linux/bio.h>
18 #include <linux/device.h>
19 #include <linux/pci.h>
20 #include <linux/completion.h>
21 #ifdef CONFIG_BLK_DEV_IDEACPI
22 #include <acpi/acpi.h>
24 #include <asm/byteorder.h>
25 #include <asm/system.h>
27 #include <asm/semaphore.h>
28 #include <asm/mutex.h>
30 #if defined(CRIS) || defined(FRV)
31 # define SUPPORT_VLB_SYNC 0
33 # define SUPPORT_VLB_SYNC 1
37 * Used to indicate "no IRQ", should be a value that cannot be an IRQ
41 #define IDE_NO_IRQ (-1)
43 typedef unsigned char byte; /* used everywhere */
46 * Probably not wise to fiddle with these
48 #define ERROR_MAX 8 /* Max read/write errors per sector */
49 #define ERROR_RESET 3 /* Reset controller every 4th retry */
50 #define ERROR_RECAL 1 /* Recalibrate every 2nd retry */
55 #define IDE_TUNE_NOAUTO 2
56 #define IDE_TUNE_AUTO 1
57 #define IDE_TUNE_DEFAULT 0
63 #define DMA_PIO_RETRY 1 /* retrying in PIO */
65 #define HWIF(drive) ((ide_hwif_t *)((drive)->hwif))
66 #define HWGROUP(drive) ((ide_hwgroup_t *)(HWIF(drive)->hwgroup))
69 * Definitions for accessing IDE controller registers
71 #define IDE_NR_PORTS (10)
73 #define IDE_DATA_OFFSET (0)
74 #define IDE_ERROR_OFFSET (1)
75 #define IDE_NSECTOR_OFFSET (2)
76 #define IDE_SECTOR_OFFSET (3)
77 #define IDE_LCYL_OFFSET (4)
78 #define IDE_HCYL_OFFSET (5)
79 #define IDE_SELECT_OFFSET (6)
80 #define IDE_STATUS_OFFSET (7)
81 #define IDE_CONTROL_OFFSET (8)
82 #define IDE_IRQ_OFFSET (9)
84 #define IDE_FEATURE_OFFSET IDE_ERROR_OFFSET
85 #define IDE_COMMAND_OFFSET IDE_STATUS_OFFSET
87 #define IDE_DATA_REG (HWIF(drive)->io_ports[IDE_DATA_OFFSET])
88 #define IDE_ERROR_REG (HWIF(drive)->io_ports[IDE_ERROR_OFFSET])
89 #define IDE_NSECTOR_REG (HWIF(drive)->io_ports[IDE_NSECTOR_OFFSET])
90 #define IDE_SECTOR_REG (HWIF(drive)->io_ports[IDE_SECTOR_OFFSET])
91 #define IDE_LCYL_REG (HWIF(drive)->io_ports[IDE_LCYL_OFFSET])
92 #define IDE_HCYL_REG (HWIF(drive)->io_ports[IDE_HCYL_OFFSET])
93 #define IDE_SELECT_REG (HWIF(drive)->io_ports[IDE_SELECT_OFFSET])
94 #define IDE_STATUS_REG (HWIF(drive)->io_ports[IDE_STATUS_OFFSET])
95 #define IDE_CONTROL_REG (HWIF(drive)->io_ports[IDE_CONTROL_OFFSET])
96 #define IDE_IRQ_REG (HWIF(drive)->io_ports[IDE_IRQ_OFFSET])
98 #define IDE_FEATURE_REG IDE_ERROR_REG
99 #define IDE_COMMAND_REG IDE_STATUS_REG
100 #define IDE_ALTSTATUS_REG IDE_CONTROL_REG
101 #define IDE_IREASON_REG IDE_NSECTOR_REG
102 #define IDE_BCOUNTL_REG IDE_LCYL_REG
103 #define IDE_BCOUNTH_REG IDE_HCYL_REG
105 #define OK_STAT(stat,good,bad) (((stat)&((good)|(bad)))==(good))
106 #define BAD_R_STAT (BUSY_STAT | ERR_STAT)
107 #define BAD_W_STAT (BAD_R_STAT | WRERR_STAT)
108 #define BAD_STAT (BAD_R_STAT | DRQ_STAT)
109 #define DRIVE_READY (READY_STAT | SEEK_STAT)
110 #define DATA_READY (DRQ_STAT)
112 #define BAD_CRC (ABRT_ERR | ICRC_ERR)
114 #define SATA_NR_PORTS (3) /* 16 possible ?? */
116 #define SATA_STATUS_OFFSET (0)
117 #define SATA_STATUS_REG (HWIF(drive)->sata_scr[SATA_STATUS_OFFSET])
118 #define SATA_ERROR_OFFSET (1)
119 #define SATA_ERROR_REG (HWIF(drive)->sata_scr[SATA_ERROR_OFFSET])
120 #define SATA_CONTROL_OFFSET (2)
121 #define SATA_CONTROL_REG (HWIF(drive)->sata_scr[SATA_CONTROL_OFFSET])
123 #define SATA_MISC_OFFSET (0)
124 #define SATA_MISC_REG (HWIF(drive)->sata_misc[SATA_MISC_OFFSET])
125 #define SATA_PHY_OFFSET (1)
126 #define SATA_PHY_REG (HWIF(drive)->sata_misc[SATA_PHY_OFFSET])
127 #define SATA_IEN_OFFSET (2)
128 #define SATA_IEN_REG (HWIF(drive)->sata_misc[SATA_IEN_OFFSET])
131 * Our Physical Region Descriptor (PRD) table should be large enough
132 * to handle the biggest I/O request we are likely to see. Since requests
133 * can have no more than 256 sectors, and since the typical blocksize is
134 * two or more sectors, we could get by with a limit of 128 entries here for
135 * the usual worst case. Most requests seem to include some contiguous blocks,
136 * further reducing the number of table entries required.
138 * The driver reverts to PIO mode for individual requests that exceed
139 * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
140 * 100% of all crazy scenarios here is not necessary.
142 * As it turns out though, we must allocate a full 4KB page for this,
143 * so the two PRD tables (ide0 & ide1) will each get half of that,
144 * allowing each to have about 256 entries (8 bytes each) from this.
147 #define PRD_ENTRIES 256
150 * Some more useful definitions
152 #define PARTN_BITS 6 /* number of minor dev bits for partitions */
153 #define MAX_DRIVES 2 /* per interface; 2 assumed by lots of code */
154 #define SECTOR_SIZE 512
155 #define SECTOR_WORDS (SECTOR_SIZE / 4) /* number of 32bit words per sector */
156 #define IDE_LARGE_SEEK(b1,b2,t) (((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))
159 * Timeouts for various operations:
161 #define WAIT_DRQ (HZ/10) /* 100msec - spec allows up to 20ms */
162 #define WAIT_READY (5*HZ) /* 5sec - some laptops are very slow */
163 #define WAIT_PIDENTIFY (10*HZ) /* 10sec - should be less than 3ms (?), if all ATAPI CD is closed at boot */
164 #define WAIT_WORSTCASE (30*HZ) /* 30sec - worst case when spinning up */
165 #define WAIT_CMD (10*HZ) /* 10sec - maximum wait for an IRQ to happen */
166 #define WAIT_MIN_SLEEP (2*HZ/100) /* 20msec - minimum sleep time */
169 * Check for an interrupt and acknowledge the interrupt status
172 typedef int (ide_ack_intr_t)(struct hwif_s *);
175 * hwif_chipset_t is used to keep track of the specific hardware
176 * chipset used by each IDE interface, if known.
178 enum { ide_unknown, ide_generic, ide_pci,
179 ide_cmd640, ide_dtc2278, ide_ali14xx,
180 ide_qd65xx, ide_umc8672, ide_ht6560b,
181 ide_rz1000, ide_trm290,
182 ide_cmd646, ide_cy82c693, ide_4drives,
183 ide_pmac, ide_etrax100, ide_acorn,
184 ide_au1xxx, ide_forced
187 typedef u8 hwif_chipset_t;
190 * Structure to hold all information about the location of this port
192 typedef struct hw_regs_s {
193 unsigned long io_ports[IDE_NR_PORTS]; /* task file registers */
194 int irq; /* our irq number */
195 ide_ack_intr_t *ack_intr; /* acknowledge interrupt */
196 hwif_chipset_t chipset;
200 struct hwif_s * ide_find_port(unsigned long);
201 void ide_init_port_data(struct hwif_s *, unsigned int);
202 void ide_init_port_hw(struct hwif_s *, hw_regs_t *);
205 int ide_register_hw(hw_regs_t *, void (*)(struct ide_drive_s *),
208 void ide_setup_ports( hw_regs_t *hw,
213 ide_ack_intr_t *ack_intr,
219 static inline void ide_std_init_ports(hw_regs_t *hw,
220 unsigned long io_addr,
221 unsigned long ctl_addr)
225 for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
226 hw->io_ports[i] = io_addr++;
228 hw->io_ports[IDE_CONTROL_OFFSET] = ctl_addr;
233 #if !defined(MAX_HWIFS) || defined(CONFIG_EMBEDDED)
235 #define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
238 /* needed on alpha, x86/x86_64, ia64, mips, ppc32 and sh */
239 #ifndef IDE_ARCH_OBSOLETE_DEFAULTS
240 # define ide_default_io_base(index) (0)
241 # define ide_default_irq(base) (0)
242 # define ide_init_default_irq(base) (0)
245 #ifdef CONFIG_IDE_ARCH_OBSOLETE_INIT
246 static inline void ide_init_hwif_ports(hw_regs_t *hw,
247 unsigned long io_addr,
248 unsigned long ctl_addr,
252 ide_std_init_ports(hw, io_addr, ide_default_io_ctl(io_addr));
254 ide_std_init_ports(hw, io_addr, ctl_addr);
259 hw->io_ports[IDE_IRQ_OFFSET] = 0;
262 if (ppc_ide_md.ide_init_hwif)
263 ppc_ide_md.ide_init_hwif(hw, io_addr, ctl_addr, irq);
267 static inline void ide_init_hwif_ports(hw_regs_t *hw,
268 unsigned long io_addr,
269 unsigned long ctl_addr,
272 if (io_addr || ctl_addr)
273 printk(KERN_WARNING "%s: must not be called\n", __FUNCTION__);
275 #endif /* CONFIG_IDE_ARCH_OBSOLETE_INIT */
277 /* Currently only m68k, apus and m8xx need it */
278 #ifndef IDE_ARCH_ACK_INTR
279 # define ide_ack_intr(hwif) (1)
282 /* Currently only Atari needs it */
283 #ifndef IDE_ARCH_LOCK
284 # define ide_release_lock() do {} while (0)
285 # define ide_get_lock(hdlr, data) do {} while (0)
286 #endif /* IDE_ARCH_LOCK */
289 * Now for the data we need to maintain per-drive: ide_drive_t
292 #define ide_scsi 0x21
293 #define ide_disk 0x20
294 #define ide_optical 0x7
295 #define ide_cdrom 0x5
297 #define ide_floppy 0x0
300 * Special Driver Flags
302 * set_geometry : respecify drive geometry
303 * recalibrate : seek to cyl 0
304 * set_multmode : set multmode count
305 * set_tune : tune interface for drive
306 * serviced : service command
312 unsigned set_geometry : 1;
313 unsigned recalibrate : 1;
314 unsigned set_multmode : 1;
315 unsigned set_tune : 1;
316 unsigned serviced : 1;
317 unsigned reserved : 3;
322 * ATA-IDE Select Register, aka Device-Head
324 * head : always zeros here
325 * unit : drive select number: 0/1
327 * lba : using LBA instead of CHS
333 #if defined(__LITTLE_ENDIAN_BITFIELD)
339 #elif defined(__BIG_ENDIAN_BITFIELD)
346 #error "Please fix <asm/byteorder.h>"
349 } select_t, ata_select_t;
352 * Status returned from various ide_ functions
355 ide_stopped, /* no drive operation was started */
356 ide_started, /* a drive operation was started, handler was set */
360 struct ide_settings_s;
362 #ifdef CONFIG_BLK_DEV_IDEACPI
363 struct ide_acpi_drive_link;
364 struct ide_acpi_hwif_link;
367 typedef struct ide_drive_s {
368 char name[4]; /* drive name, such as "hda" */
369 char driver_req[10]; /* requests specific driver */
371 struct request_queue *queue; /* request queue */
373 struct request *rq; /* current request */
374 struct ide_drive_s *next; /* circular list of hwgroup drives */
375 void *driver_data; /* extra driver data */
376 struct hd_driveid *id; /* drive model identification info */
377 #ifdef CONFIG_IDE_PROC_FS
378 struct proc_dir_entry *proc; /* /proc/ide/ directory entry */
379 struct ide_settings_s *settings;/* /proc/ide/ drive settings */
381 struct hwif_s *hwif; /* actually (ide_hwif_t *) */
383 unsigned long sleep; /* sleep until this time */
384 unsigned long service_start; /* time we started last request */
385 unsigned long service_time; /* service time of last request */
386 unsigned long timeout; /* max time to wait for irq */
388 special_t special; /* special action flags */
389 select_t select; /* basic drive/head select reg value */
391 u8 keep_settings; /* restore settings after drive reset */
392 u8 using_dma; /* disk is using dma for read/write */
393 u8 retry_pio; /* retrying dma capable host in pio */
394 u8 state; /* retry state */
395 u8 waiting_for_dma; /* dma currently in progress */
396 u8 unmask; /* okay to unmask other irqs */
397 u8 bswap; /* byte swap data */
398 u8 noflush; /* don't attempt flushes */
399 u8 dsc_overlap; /* DSC overlap */
400 u8 nice1; /* give potential excess bandwidth */
402 unsigned present : 1; /* drive is physically present */
403 unsigned dead : 1; /* device ejected hint */
404 unsigned id_read : 1; /* 1=id read from disk 0 = synthetic */
405 unsigned noprobe : 1; /* from: hdx=noprobe */
406 unsigned removable : 1; /* 1 if need to do check_media_change */
407 unsigned attach : 1; /* needed for removable devices */
408 unsigned forced_geom : 1; /* 1 if hdx=c,h,s was given at boot */
409 unsigned no_unmask : 1; /* disallow setting unmask bit */
410 unsigned no_io_32bit : 1; /* disallow enabling 32bit I/O */
411 unsigned atapi_overlap : 1; /* ATAPI overlap (not supported) */
412 unsigned nice0 : 1; /* give obvious excess bandwidth */
413 unsigned nice2 : 1; /* give a share in our own bandwidth */
414 unsigned doorlocking : 1; /* for removable only: door lock/unlock works */
415 unsigned nodma : 1; /* disallow DMA */
416 unsigned autotune : 2; /* 0=default, 1=autotune, 2=noautotune */
417 unsigned remap_0_to_1 : 1; /* 0=noremap, 1=remap 0->1 (for EZDrive) */
418 unsigned blocked : 1; /* 1=powermanagment told us not to do anything, so sleep nicely */
419 unsigned vdma : 1; /* 1=doing PIO over DMA 0=doing normal DMA */
420 unsigned scsi : 1; /* 0=default, 1=ide-scsi emulation */
421 unsigned sleeping : 1; /* 1=sleeping & sleep field valid */
422 unsigned post_reset : 1;
423 unsigned udma33_warned : 1;
425 u8 addressing; /* 0=28-bit, 1=48-bit, 2=48-bit doing 28-bit */
426 u8 quirk_list; /* considered quirky, set for a specific host */
427 u8 init_speed; /* transfer rate set at boot */
428 u8 current_speed; /* current transfer rate set */
429 u8 desired_speed; /* desired transfer rate set */
430 u8 dn; /* now wide spread use */
431 u8 wcache; /* status of write cache */
432 u8 acoustic; /* acoustic management */
433 u8 media; /* disk, cdrom, tape, floppy, ... */
434 u8 ctl; /* "normal" value for IDE_CONTROL_REG */
435 u8 ready_stat; /* min status value for drive ready */
436 u8 mult_count; /* current multiple sector setting */
437 u8 mult_req; /* requested multiple sector setting */
438 u8 tune_req; /* requested drive tuning setting */
439 u8 io_32bit; /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
440 u8 bad_wstat; /* used for ignoring WRERR_STAT */
441 u8 nowerr; /* used for ignoring WRERR_STAT */
442 u8 sect0; /* offset of first sector for DM6:DDO */
443 u8 head; /* "real" number of heads */
444 u8 sect; /* "real" sectors per track */
445 u8 bios_head; /* BIOS/fdisk/LILO number of heads */
446 u8 bios_sect; /* BIOS/fdisk/LILO sectors per track */
448 unsigned int bios_cyl; /* BIOS/fdisk/LILO number of cyls */
449 unsigned int cyl; /* "real" number of cyls */
450 unsigned int drive_data; /* used by set_pio_mode/selectproc */
451 unsigned int failures; /* current failure count */
452 unsigned int max_failures; /* maximum allowed failure count */
453 u64 probed_capacity;/* initial reported media capacity (ide-cd only currently) */
455 u64 capacity64; /* total number of sectors */
457 int lun; /* logical unit */
458 int crc_count; /* crc counter to reduce drive speed */
459 #ifdef CONFIG_BLK_DEV_IDEACPI
460 struct ide_acpi_drive_link *acpidata;
462 struct list_head list;
463 struct device gendev;
464 struct completion gendev_rel_comp; /* to deal with device release() */
467 #define to_ide_device(dev)container_of(dev, ide_drive_t, gendev)
469 #define IDE_CHIPSET_PCI_MASK \
470 ((1<<ide_pci)|(1<<ide_cmd646)|(1<<ide_ali14xx))
471 #define IDE_CHIPSET_IS_PCI(c) ((IDE_CHIPSET_PCI_MASK >> (c)) & 1)
473 struct ide_port_info;
475 typedef struct hwif_s {
476 struct hwif_s *next; /* for linked-list in ide_hwgroup_t */
477 struct hwif_s *mate; /* other hwif from same PCI chip */
478 struct hwgroup_s *hwgroup; /* actually (ide_hwgroup_t *) */
479 struct proc_dir_entry *proc; /* /proc/ide/ directory entry */
481 char name[6]; /* name of interface, eg. "ide0" */
483 /* task file registers for pata and sata */
484 unsigned long io_ports[IDE_NR_PORTS];
485 unsigned long sata_scr[SATA_NR_PORTS];
486 unsigned long sata_misc[SATA_NR_PORTS];
488 ide_drive_t drives[MAX_DRIVES]; /* drive info */
490 u8 major; /* our major number */
491 u8 index; /* 0 for ide0; 1 for ide1; ... */
492 u8 channel; /* for dual-port chips: 0=primary, 1=secondary */
493 u8 straight8; /* Alan's straight 8 check */
494 u8 bus_state; /* power state of the IDE bus */
504 u8 cbl; /* cable type */
506 hwif_chipset_t chipset; /* sub-module for tuning.. */
508 struct pci_dev *pci_dev; /* for pci chipsets */
509 const struct ide_port_info *cds; /* chipset device struct */
511 ide_ack_intr_t *ack_intr;
513 void (*rw_disk)(ide_drive_t *, struct request *);
516 ide_hwif_ops_t *hwifops;
518 /* routine to program host for PIO mode */
519 void (*set_pio_mode)(ide_drive_t *, const u8);
520 /* routine to program host for DMA mode */
521 void (*set_dma_mode)(ide_drive_t *, const u8);
522 /* tweaks hardware to select drive */
523 void (*selectproc)(ide_drive_t *);
524 /* chipset polling based on hba specifics */
525 int (*reset_poll)(ide_drive_t *);
526 /* chipset specific changes to default for device-hba resets */
527 void (*pre_reset)(ide_drive_t *);
528 /* routine to reset controller after a disk reset */
529 void (*resetproc)(ide_drive_t *);
530 /* special host masking for drive selection */
531 void (*maskproc)(ide_drive_t *, int);
532 /* check host's drive quirk list */
533 void (*quirkproc)(ide_drive_t *);
534 /* driver soft-power interface */
535 int (*busproc)(ide_drive_t *, int);
537 u8 (*mdma_filter)(ide_drive_t *);
538 u8 (*udma_filter)(ide_drive_t *);
540 void (*ata_input_data)(ide_drive_t *, void *, u32);
541 void (*ata_output_data)(ide_drive_t *, void *, u32);
543 void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
544 void (*atapi_output_bytes)(ide_drive_t *, void *, u32);
546 void (*dma_host_set)(ide_drive_t *, int);
547 int (*dma_setup)(ide_drive_t *);
548 void (*dma_exec_cmd)(ide_drive_t *, u8);
549 void (*dma_start)(ide_drive_t *);
550 int (*ide_dma_end)(ide_drive_t *drive);
551 int (*ide_dma_test_irq)(ide_drive_t *drive);
552 void (*ide_dma_clear_irq)(ide_drive_t *drive);
553 void (*dma_lost_irq)(ide_drive_t *drive);
554 void (*dma_timeout)(ide_drive_t *drive);
556 void (*OUTB)(u8 addr, unsigned long port);
557 void (*OUTBSYNC)(ide_drive_t *drive, u8 addr, unsigned long port);
558 void (*OUTW)(u16 addr, unsigned long port);
559 void (*OUTSW)(unsigned long port, void *addr, u32 count);
560 void (*OUTSL)(unsigned long port, void *addr, u32 count);
562 u8 (*INB)(unsigned long port);
563 u16 (*INW)(unsigned long port);
564 void (*INSW)(unsigned long port, void *addr, u32 count);
565 void (*INSL)(unsigned long port, void *addr, u32 count);
567 /* dma physical region descriptor table (cpu view) */
568 unsigned int *dmatable_cpu;
569 /* dma physical region descriptor table (dma view) */
570 dma_addr_t dmatable_dma;
571 /* Scatter-gather list used to build the above */
572 struct scatterlist *sg_table;
573 int sg_max_nents; /* Maximum number of entries in it */
574 int sg_nents; /* Current number of entries in it */
575 int sg_dma_direction; /* dma transfer direction */
577 /* data phase of the active command (currently only valid for PIO/DMA) */
582 struct scatterlist *cursg;
583 unsigned int cursg_ofs;
585 int rqsize; /* max sectors per request */
586 int irq; /* our irq number */
588 unsigned long dma_base; /* base addr for dma ports */
589 unsigned long dma_command; /* dma command register */
590 unsigned long dma_vendor1; /* dma vendor 1 register */
591 unsigned long dma_status; /* dma status register */
592 unsigned long dma_vendor3; /* dma vendor 3 register */
593 unsigned long dma_prdtable; /* actual prd table address */
595 unsigned long config_data; /* for use by chipset-specific code */
596 unsigned long select_data; /* for use by chipset-specific code */
598 unsigned long extra_base; /* extra addr for dma ports */
599 unsigned extra_ports; /* number of extra dma ports */
601 unsigned noprobe : 1; /* don't probe for this interface */
602 unsigned present : 1; /* this interface exists */
603 unsigned hold : 1; /* this interface is always present */
604 unsigned serialized : 1; /* serialized all channel operation */
605 unsigned sharing_irq: 1; /* 1 = sharing irq with another hwif */
606 unsigned reset : 1; /* reset after probe */
607 unsigned auto_poll : 1; /* supports nop auto-poll */
608 unsigned sg_mapped : 1; /* sg_table and sg_nents are ready */
609 unsigned no_io_32bit : 1; /* 1 = can not do 32-bit IO ops */
610 unsigned mmio : 1; /* host uses MMIO */
612 struct device gendev;
613 struct completion gendev_rel_comp; /* To deal with device release() */
615 void *hwif_data; /* extra hwif data */
619 #ifdef CONFIG_BLK_DEV_IDEACPI
620 struct ide_acpi_hwif_link *acpidata;
622 } ____cacheline_internodealigned_in_smp ide_hwif_t;
625 * internal ide interrupt handler type
627 typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
628 typedef int (ide_expiry_t)(ide_drive_t *);
630 typedef struct hwgroup_s {
631 /* irq handler, if active */
632 ide_startstop_t (*handler)(ide_drive_t *);
633 /* irq handler, suspended if active */
634 ide_startstop_t (*handler_save)(ide_drive_t *);
635 /* BOOL: protects all fields below */
637 /* BOOL: wake us up on timer expiry */
638 unsigned int sleeping : 1;
639 /* BOOL: polling active & poll_timeout field valid */
640 unsigned int polling : 1;
641 /* BOOL: in a polling reset situation. Must not trigger another reset yet */
642 unsigned int resetting : 1;
646 /* ptr to current hwif in linked-list */
649 /* for pci chipsets */
650 struct pci_dev *pci_dev;
652 /* current request */
655 struct timer_list timer;
656 /* local copy of current write rq */
658 /* timeout value during long polls */
659 unsigned long poll_timeout;
660 /* queried upon timeouts */
661 int (*expiry)(ide_drive_t *);
662 /* ide_system_bus_speed */
667 unsigned char cmd_buf[4];
670 typedef struct ide_driver_s ide_driver_t;
672 extern struct mutex ide_setting_mtx;
674 int set_io_32bit(ide_drive_t *, int);
675 int set_pio_mode(ide_drive_t *, int);
676 int set_using_dma(ide_drive_t *, int);
678 #ifdef CONFIG_IDE_PROC_FS
680 * configurable drive settings
687 #define SETTING_READ (1 << 0)
688 #define SETTING_WRITE (1 << 1)
689 #define SETTING_RW (SETTING_READ | SETTING_WRITE)
691 typedef int (ide_procset_t)(ide_drive_t *, int);
692 typedef struct ide_settings_s {
703 struct ide_settings_s *next;
706 int ide_add_setting(ide_drive_t *, const char *, int, int, int, int, int, int, void *, ide_procset_t *set);
709 * /proc/ide interface
714 read_proc_t *read_proc;
715 write_proc_t *write_proc;
718 void proc_ide_create(void);
719 void proc_ide_destroy(void);
720 void ide_proc_register_port(ide_hwif_t *);
721 void ide_proc_unregister_port(ide_hwif_t *);
722 void ide_proc_register_driver(ide_drive_t *, ide_driver_t *);
723 void ide_proc_unregister_driver(ide_drive_t *, ide_driver_t *);
725 void ide_add_generic_settings(ide_drive_t *);
727 read_proc_t proc_ide_read_capacity;
728 read_proc_t proc_ide_read_geometry;
730 #ifdef CONFIG_BLK_DEV_IDEPCI
731 void ide_pci_create_host_proc(const char *, get_info_t *);
735 * Standard exit stuff:
737 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
746 *start = page + off; \
750 static inline void proc_ide_create(void) { ; }
751 static inline void proc_ide_destroy(void) { ; }
752 static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
753 static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
754 static inline void ide_proc_register_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
755 static inline void ide_proc_unregister_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
756 static inline void ide_add_generic_settings(ide_drive_t *drive) { ; }
757 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
761 * Power Management step value (rq->pm->pm_step).
763 * The step value starts at 0 (ide_pm_state_start_suspend) for a
764 * suspend operation or 1000 (ide_pm_state_start_resume) for a
767 * For each step, the core calls the subdriver start_power_step() first.
769 * - ide_stopped : In this case, the core calls us back again unless
770 * step have been set to ide_power_state_completed.
771 * - ide_started : In this case, the channel is left busy until an
772 * async event (interrupt) occurs.
773 * Typically, start_power_step() will issue a taskfile request with
776 * Upon reception of the interrupt, the core will call complete_power_step()
777 * with the error code if any. This routine should update the step value
778 * and return. It should not start a new request. The core will call
779 * start_power_step for the new step value, unless step have been set to
780 * ide_power_state_completed.
782 * Subdrivers are expected to define their own additional power
783 * steps from 1..999 for suspend and from 1001..1999 for resume,
784 * other values are reserved for future use.
788 ide_pm_state_completed = -1,
789 ide_pm_state_start_suspend = 0,
790 ide_pm_state_start_resume = 1000,
794 * Subdrivers support.
796 * The gendriver.owner field should be set to the module owner of this driver.
797 * The gendriver.name field should be set to the name of this driver
799 struct ide_driver_s {
802 unsigned supports_dsc_overlap : 1;
803 ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
804 int (*end_request)(ide_drive_t *, int, int);
805 ide_startstop_t (*error)(ide_drive_t *, struct request *rq, u8, u8);
806 ide_startstop_t (*abort)(ide_drive_t *, struct request *rq);
807 struct device_driver gen_driver;
808 int (*probe)(ide_drive_t *);
809 void (*remove)(ide_drive_t *);
810 void (*resume)(ide_drive_t *);
811 void (*shutdown)(ide_drive_t *);
812 #ifdef CONFIG_IDE_PROC_FS
813 ide_proc_entry_t *proc;
817 #define to_ide_driver(drv) container_of(drv, ide_driver_t, gen_driver)
819 int generic_ide_ioctl(ide_drive_t *, struct file *, struct block_device *, unsigned, unsigned long);
822 * ide_hwifs[] is the master data structure used to keep track
823 * of just about everything in ide.c. Whenever possible, routines
824 * should be using pointers to a drive (ide_drive_t *) or
825 * pointers to a hwif (ide_hwif_t *), rather than indexing this
826 * structure directly (the allocation/layout may change!).
830 extern ide_hwif_t ide_hwifs[]; /* master data repository */
832 extern int noautodma;
834 extern int ide_end_request (ide_drive_t *drive, int uptodate, int nrsecs);
835 int ide_end_dequeued_request(ide_drive_t *drive, struct request *rq,
836 int uptodate, int nr_sectors);
838 extern void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);
840 void ide_execute_command(ide_drive_t *, u8, ide_handler_t *, unsigned int,
843 ide_startstop_t __ide_error(ide_drive_t *, struct request *, u8, u8);
845 ide_startstop_t ide_error (ide_drive_t *drive, const char *msg, byte stat);
847 ide_startstop_t __ide_abort(ide_drive_t *, struct request *);
849 extern ide_startstop_t ide_abort(ide_drive_t *, const char *);
851 extern void ide_fix_driveid(struct hd_driveid *);
853 extern void ide_fixstring(u8 *, const int, const int);
855 int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
857 extern ide_startstop_t ide_do_reset (ide_drive_t *);
859 extern void ide_init_drive_cmd (struct request *rq);
862 * "action" parameter type for ide_do_drive_cmd() below.
865 ide_wait, /* insert rq at end of list, and wait for it */
866 ide_preempt, /* insert rq in front of current request */
867 ide_head_wait, /* insert rq in front of current request and wait for it */
868 ide_end /* insert rq at end of list, but don't wait for it */
871 extern int ide_do_drive_cmd(ide_drive_t *, struct request *, ide_action_t);
873 extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);
876 * Issue ATA command and wait for completion.
877 * Use for implementing commands in kernel
879 * (ide_drive_t *drive, u8 cmd, u8 nsect, u8 feature, u8 sectors, u8 *buf)
881 extern int ide_wait_cmd(ide_drive_t *, u8, u8, u8, u8, u8 *);
884 IDE_TFLAG_LBA48 = (1 << 0),
885 IDE_TFLAG_NO_SELECT_MASK = (1 << 1),
886 IDE_TFLAG_FLAGGED = (1 << 2),
887 IDE_TFLAG_OUT_DATA = (1 << 3),
888 IDE_TFLAG_OUT_HOB_FEATURE = (1 << 4),
889 IDE_TFLAG_OUT_HOB_NSECT = (1 << 5),
890 IDE_TFLAG_OUT_HOB_LBAL = (1 << 6),
891 IDE_TFLAG_OUT_HOB_LBAM = (1 << 7),
892 IDE_TFLAG_OUT_HOB_LBAH = (1 << 8),
893 IDE_TFLAG_OUT_HOB = IDE_TFLAG_OUT_HOB_FEATURE |
894 IDE_TFLAG_OUT_HOB_NSECT |
895 IDE_TFLAG_OUT_HOB_LBAL |
896 IDE_TFLAG_OUT_HOB_LBAM |
897 IDE_TFLAG_OUT_HOB_LBAH,
898 IDE_TFLAG_OUT_FEATURE = (1 << 9),
899 IDE_TFLAG_OUT_NSECT = (1 << 10),
900 IDE_TFLAG_OUT_LBAL = (1 << 11),
901 IDE_TFLAG_OUT_LBAM = (1 << 12),
902 IDE_TFLAG_OUT_LBAH = (1 << 13),
903 IDE_TFLAG_OUT_TF = IDE_TFLAG_OUT_FEATURE |
904 IDE_TFLAG_OUT_NSECT |
908 IDE_TFLAG_OUT_DEVICE = (1 << 14),
909 IDE_TFLAG_WRITE = (1 << 15),
910 IDE_TFLAG_FLAGGED_SET_IN_FLAGS = (1 << 16),
911 IDE_TFLAG_IN_DATA = (1 << 17),
912 IDE_TFLAG_CUSTOM_HANDLER = (1 << 18),
913 IDE_TFLAG_DMA_PIO_FALLBACK = (1 << 19),
914 IDE_TFLAG_IN_HOB_FEATURE = (1 << 20),
915 IDE_TFLAG_IN_HOB_NSECT = (1 << 21),
916 IDE_TFLAG_IN_HOB_LBAL = (1 << 22),
917 IDE_TFLAG_IN_HOB_LBAM = (1 << 23),
918 IDE_TFLAG_IN_HOB_LBAH = (1 << 24),
919 IDE_TFLAG_IN_HOB_LBA = IDE_TFLAG_IN_HOB_LBAL |
920 IDE_TFLAG_IN_HOB_LBAM |
921 IDE_TFLAG_IN_HOB_LBAH,
922 IDE_TFLAG_IN_HOB = IDE_TFLAG_IN_HOB_FEATURE |
923 IDE_TFLAG_IN_HOB_NSECT |
924 IDE_TFLAG_IN_HOB_LBA,
925 IDE_TFLAG_IN_NSECT = (1 << 25),
926 IDE_TFLAG_IN_LBAL = (1 << 26),
927 IDE_TFLAG_IN_LBAM = (1 << 27),
928 IDE_TFLAG_IN_LBAH = (1 << 28),
929 IDE_TFLAG_IN_LBA = IDE_TFLAG_IN_LBAL |
932 IDE_TFLAG_IN_TF = IDE_TFLAG_IN_NSECT |
934 IDE_TFLAG_IN_DEVICE = (1 << 29),
937 struct ide_taskfile {
938 u8 hob_data; /* 0: high data byte (for TASKFILE IOCTL) */
940 u8 hob_feature; /* 1-5: additional data to support LBA48 */
946 u8 data; /* 6: low data byte (for TASKFILE IOCTL) */
949 u8 error; /* read: error */
950 u8 feature; /* write: feature */
953 u8 nsect; /* 8: number of sectors */
954 u8 lbal; /* 9: LBA low */
955 u8 lbam; /* 10: LBA mid */
956 u8 lbah; /* 11: LBA high */
958 u8 device; /* 12: device select */
961 u8 status; /*  read: status  */
962 u8 command; /* write: command */
966 typedef struct ide_task_s {
968 struct ide_taskfile tf;
973 struct request *rq; /* copy of request */
974 void *special; /* valid_t generally */
977 void ide_tf_load(ide_drive_t *, ide_task_t *);
978 void ide_tf_read(ide_drive_t *, ide_task_t *);
980 extern void SELECT_DRIVE(ide_drive_t *);
981 extern void SELECT_MASK(ide_drive_t *, int);
983 extern int drive_is_ready(ide_drive_t *);
985 void ide_pktcmd_tf_load(ide_drive_t *, u32, u16, u8);
987 ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
989 int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
990 int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
992 int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
993 int ide_cmd_ioctl(ide_drive_t *, unsigned int, unsigned long);
994 int ide_task_ioctl(ide_drive_t *, unsigned int, unsigned long);
996 extern int system_bus_clock(void);
998 extern int ide_driveid_update(ide_drive_t *);
999 extern int ide_ata66_check(ide_drive_t *, ide_task_t *);
1000 extern int ide_config_drive_speed(ide_drive_t *, u8);
1001 extern u8 eighty_ninty_three (ide_drive_t *);
1002 extern int set_transfer(ide_drive_t *, ide_task_t *);
1003 extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
1005 extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);
1007 extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
1009 extern int ide_spin_wait_hwgroup(ide_drive_t *);
1010 extern void ide_timer_expiry(unsigned long);
1011 extern irqreturn_t ide_intr(int irq, void *dev_id);
1012 extern void do_ide_request(struct request_queue *);
1014 void ide_init_disk(struct gendisk *, ide_drive_t *);
1016 #ifdef CONFIG_IDEPCI_PCIBUS_ORDER
1017 extern int ide_scan_direction;
1018 int __init ide_scan_pcibus(void);
1019 extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
1020 #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
1022 #define ide_pci_register_driver(d) pci_register_driver(d)
1025 void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *, int, u8 *);
1026 void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
1028 extern void default_hwif_iops(ide_hwif_t *);
1029 extern void default_hwif_mmiops(ide_hwif_t *);
1030 extern void default_hwif_transport(ide_hwif_t *);
1032 typedef struct ide_pci_enablebit_s {
1033 u8 reg; /* byte pci reg holding the enable-bit */
1034 u8 mask; /* mask to isolate the enable-bit */
1035 u8 val; /* value of masked reg when "enabled" */
1036 } ide_pci_enablebit_t;
1039 /* Uses ISA control ports not PCI ones. */
1040 IDE_HFLAG_ISA_PORTS = (1 << 0),
1041 /* single port device */
1042 IDE_HFLAG_SINGLE = (1 << 1),
1043 /* don't use legacy PIO blacklist */
1044 IDE_HFLAG_PIO_NO_BLACKLIST = (1 << 2),
1045 /* don't use conservative PIO "downgrade" */
1046 IDE_HFLAG_PIO_NO_DOWNGRADE = (1 << 3),
1047 /* use PIO8/9 for prefetch off/on */
1048 IDE_HFLAG_ABUSE_PREFETCH = (1 << 4),
1049 /* use PIO6/7 for fast-devsel off/on */
1050 IDE_HFLAG_ABUSE_FAST_DEVSEL = (1 << 5),
1051 /* use 100-102 and 200-202 PIO values to set DMA modes */
1052 IDE_HFLAG_ABUSE_DMA_MODES = (1 << 6),
1054 * keep DMA setting when programming PIO mode, may be used only
1055 * for hosts which have separate PIO and DMA timings (ie. PMAC)
1057 IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
1058 /* program host for the transfer mode after programming device */
1059 IDE_HFLAG_POST_SET_MODE = (1 << 8),
1060 /* don't program host/device for the transfer mode ("smart" hosts) */
1061 IDE_HFLAG_NO_SET_MODE = (1 << 9),
1062 /* trust BIOS for programming chipset/device for DMA */
1063 IDE_HFLAG_TRUST_BIOS_FOR_DMA = (1 << 10),
1064 /* host uses VDMA */
1065 IDE_HFLAG_VDMA = (1 << 11),
1066 /* ATAPI DMA is unsupported */
1067 IDE_HFLAG_NO_ATAPI_DMA = (1 << 12),
1068 /* set if host is a "bootable" controller */
1069 IDE_HFLAG_BOOTABLE = (1 << 13),
1070 /* host doesn't support DMA */
1071 IDE_HFLAG_NO_DMA = (1 << 14),
1072 /* check if host is PCI IDE device before allowing DMA */
1073 IDE_HFLAG_NO_AUTODMA = (1 << 15),
1074 /* host is CS5510/CS5520 */
1075 IDE_HFLAG_CS5520 = (1 << 16),
1077 IDE_HFLAG_NO_LBA48 = (1 << 17),
1079 IDE_HFLAG_NO_LBA48_DMA = (1 << 18),
1080 /* data FIFO is cleared by an error */
1081 IDE_HFLAG_ERROR_STOPS_FIFO = (1 << 19),
1082 /* serialize ports */
1083 IDE_HFLAG_SERIALIZE = (1 << 20),
1084 /* use legacy IRQs */
1085 IDE_HFLAG_LEGACY_IRQS = (1 << 21),
1086 /* force use of legacy IRQs */
1087 IDE_HFLAG_FORCE_LEGACY_IRQS = (1 << 22),
1088 /* limit LBA48 requests to 256 sectors */
1089 IDE_HFLAG_RQSIZE_256 = (1 << 23),
1090 /* use 32-bit I/O ops */
1091 IDE_HFLAG_IO_32BIT = (1 << 24),
1093 IDE_HFLAG_UNMASK_IRQS = (1 << 25),
1094 IDE_HFLAG_ABUSE_SET_DMA_MODE = (1 << 26),
1095 /* host is CY82C693 */
1096 IDE_HFLAG_CY82C693 = (1 << 27),
1099 #ifdef CONFIG_BLK_DEV_OFFBOARD
1100 # define IDE_HFLAG_OFF_BOARD IDE_HFLAG_BOOTABLE
1102 # define IDE_HFLAG_OFF_BOARD 0
1105 struct ide_port_info {
1107 unsigned int (*init_chipset)(struct pci_dev *, const char *);
1108 void (*init_iops)(ide_hwif_t *);
1109 void (*init_hwif)(ide_hwif_t *);
1110 void (*init_dma)(ide_hwif_t *, unsigned long);
1111 ide_pci_enablebit_t enablebits[2];
1112 hwif_chipset_t chipset;
1121 int ide_setup_pci_device(struct pci_dev *, const struct ide_port_info *);
1122 int ide_setup_pci_devices(struct pci_dev *, struct pci_dev *, const struct ide_port_info *);
1124 void ide_map_sg(ide_drive_t *, struct request *);
1125 void ide_init_sg_cmd(ide_drive_t *, struct request *);
1127 #define BAD_DMA_DRIVE 0
1128 #define GOOD_DMA_DRIVE 1
1130 struct drive_list_entry {
1131 const char *id_model;
1132 const char *id_firmware;
1135 int ide_in_drive_list(struct hd_driveid *, const struct drive_list_entry *);
1137 #ifdef CONFIG_BLK_DEV_IDEDMA
1138 int __ide_dma_bad_drive(ide_drive_t *);
1139 int ide_id_dma_bug(ide_drive_t *);
1141 u8 ide_find_dma_mode(ide_drive_t *, u8);
1143 static inline u8 ide_max_dma_mode(ide_drive_t *drive)
1145 return ide_find_dma_mode(drive, XFER_UDMA_6);
1148 void ide_dma_off_quietly(ide_drive_t *);
1149 void ide_dma_off(ide_drive_t *);
1150 void ide_dma_on(ide_drive_t *);
1151 int ide_set_dma(ide_drive_t *);
1152 ide_startstop_t ide_dma_intr(ide_drive_t *);
1154 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
1155 extern int ide_build_sglist(ide_drive_t *, struct request *);
1156 extern int ide_build_dmatable(ide_drive_t *, struct request *);
1157 extern void ide_destroy_dmatable(ide_drive_t *);
1158 extern int ide_release_dma(ide_hwif_t *);
1159 extern void ide_setup_dma(ide_hwif_t *, unsigned long, unsigned int);
1161 void ide_dma_host_set(ide_drive_t *, int);
1162 extern int ide_dma_setup(ide_drive_t *);
1163 extern void ide_dma_start(ide_drive_t *);
1164 extern int __ide_dma_end(ide_drive_t *);
1165 extern void ide_dma_lost_irq(ide_drive_t *);
1166 extern void ide_dma_timeout(ide_drive_t *);
1167 #endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
1170 static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
1171 static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
1172 static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
1173 static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
1174 static inline void ide_dma_off(ide_drive_t *drive) { ; }
1175 static inline void ide_dma_on(ide_drive_t *drive) { ; }
1176 static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
1177 static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
1178 #endif /* CONFIG_BLK_DEV_IDEDMA */
1180 #ifndef CONFIG_BLK_DEV_IDEDMA_PCI
1181 static inline void ide_release_dma(ide_hwif_t *drive) {;}
1184 #ifdef CONFIG_BLK_DEV_IDEACPI
1185 extern int ide_acpi_exec_tfs(ide_drive_t *drive);
1186 extern void ide_acpi_get_timing(ide_hwif_t *hwif);
1187 extern void ide_acpi_push_timing(ide_hwif_t *hwif);
1188 extern void ide_acpi_init(ide_hwif_t *hwif);
1189 extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
1191 static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
1192 static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
1193 static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
1194 static inline void ide_acpi_init(ide_hwif_t *hwif) { ; }
1195 static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
1198 extern int ide_hwif_request_regions(ide_hwif_t *hwif);
1199 extern void ide_hwif_release_regions(ide_hwif_t* hwif);
1200 extern void ide_unregister (unsigned int index);
1202 void ide_register_region(struct gendisk *);
1203 void ide_unregister_region(struct gendisk *);
1205 void ide_undecoded_slave(ide_drive_t *);
1207 int ide_device_add_all(u8 *idx);
1208 int ide_device_add(u8 idx[4]);
1210 static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
1212 return hwif->hwif_data;
1215 static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
1217 hwif->hwif_data = data;
1220 const char *ide_xfer_verbose(u8 mode);
1221 extern void ide_toggle_bounce(ide_drive_t *drive, int on);
1222 extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);
1224 static inline int ide_dev_has_iordy(struct hd_driveid *id)
1226 return ((id->field_valid & 2) && (id->capability & 8)) ? 1 : 0;
1229 static inline int ide_dev_is_sata(struct hd_driveid *id)
1232 * See if word 93 is 0 AND drive is at least ATA-5 compatible
1233 * verifying that word 80 by casting it to a signed type --
1234 * this trick allows us to filter out the reserved values of
1235 * 0x0000 and 0xffff along with the earlier ATA revisions...
1237 if (id->hw_config == 0 && (short)id->major_rev_num >= 0x0020)
1242 u64 ide_get_lba_addr(struct ide_taskfile *, int);
1243 u8 ide_dump_status(ide_drive_t *, const char *, u8);
1245 typedef struct ide_pio_timings_s {
1246 int setup_time; /* Address setup (ns) minimum */
1247 int active_time; /* Active pulse (ns) minimum */
1248 int cycle_time; /* Cycle time (ns) minimum = */
1249 /* active + recovery (+ setup for some chips) */
1250 } ide_pio_timings_t;
1252 unsigned int ide_pio_cycle_time(ide_drive_t *, u8);
1253 u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
1254 extern const ide_pio_timings_t ide_pio_timings[6];
1256 int ide_set_pio_mode(ide_drive_t *, u8);
1257 int ide_set_dma_mode(ide_drive_t *, u8);
1259 void ide_set_pio(ide_drive_t *, u8);
1261 static inline void ide_set_max_pio(ide_drive_t *drive)
1263 ide_set_pio(drive, 255);
1266 extern spinlock_t ide_lock;
1267 extern struct mutex ide_cfg_mtx;
1269 * Structure locking:
1271 * ide_cfg_mtx and ide_lock together protect changes to
1272 * ide_hwif_t->{next,hwgroup}
1275 * ide_hwgroup_t->busy: ide_lock
1276 * ide_hwgroup_t->hwif: ide_lock
1277 * ide_hwif_t->mate: constant, no locking
1278 * ide_drive_t->hwif: constant, no locking
1281 #define local_irq_set(flags) do { local_save_flags((flags)); local_irq_enable_in_hardirq(); } while (0)
1283 extern struct bus_type ide_bus_type;
1285 /* check if CACHE FLUSH (EXT) command is supported (bits defined in ATA-6) */
1286 #define ide_id_has_flush_cache(id) ((id)->cfs_enable_2 & 0x3000)
1288 /* some Maxtor disks have bit 13 defined incorrectly so check bit 10 too */
1289 #define ide_id_has_flush_cache_ext(id) \
1290 (((id)->cfs_enable_2 & 0x2400) == 0x2400)
1292 static inline int hwif_to_node(ide_hwif_t *hwif)
1294 struct pci_dev *dev = hwif->pci_dev;
1295 return dev ? pcibus_to_node(dev->bus) : -1;
1298 static inline ide_drive_t *ide_get_paired_drive(ide_drive_t *drive)
1300 ide_hwif_t *hwif = HWIF(drive);
1302 return &hwif->drives[(drive->dn ^ 1) & 1];
1305 static inline void ide_set_irq(ide_drive_t *drive, int on)
1307 drive->hwif->OUTB(drive->ctl | (on ? 0 : 2), IDE_CONTROL_REG);