/* * Copyright (C) 2001-2004 by David Brownell * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License * for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software Foundation, * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* this file is part of ehci-hcd.c */ /*-------------------------------------------------------------------------*/ /* * EHCI Root Hub ... the nonsharable stuff * * Registers don't need cpu_to_le32, that happens transparently */ /*-------------------------------------------------------------------------*/ #ifdef CONFIG_PM static int ehci_bus_suspend (struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); int port; int mask; if (time_before (jiffies, ehci->next_statechange)) msleep(5); port = HCS_N_PORTS (ehci->hcs_params); spin_lock_irq (&ehci->lock); /* stop schedules, clean any completed work */ if (HC_IS_RUNNING(hcd->state)) { ehci_quiesce (ehci); hcd->state = HC_STATE_QUIESCING; } ehci->command = readl (&ehci->regs->command); if (ehci->reclaim) ehci->reclaim_ready = 1; ehci_work(ehci); /* Unlike other USB host controller types, EHCI doesn't have * any notion of "global" or bus-wide suspend. The driver has * to manually suspend all the active unsuspended ports, and * then manually resume them in the bus_resume() routine. */ ehci->bus_suspended = 0; while (port--) { u32 __iomem *reg = &ehci->regs->port_status [port]; u32 t1 = readl (reg) & ~PORT_RWC_BITS; u32 t2 = t1; /* keep track of which ports we suspend */ if ((t1 & PORT_PE) && !(t1 & PORT_OWNER) && !(t1 & PORT_SUSPEND)) { t2 |= PORT_SUSPEND; set_bit(port, &ehci->bus_suspended); } /* enable remote wakeup on all ports */ if (device_may_wakeup(&hcd->self.root_hub->dev)) t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E; else t2 &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E); if (t1 != t2) { ehci_vdbg (ehci, "port %d, %08x -> %08x\n", port + 1, t1, t2); writel (t2, reg); } } /* turn off now-idle HC */ del_timer_sync (&ehci->watchdog); ehci_halt (ehci); hcd->state = HC_STATE_SUSPENDED; /* allow remote wakeup */ mask = INTR_MASK; if (!device_may_wakeup(&hcd->self.root_hub->dev)) mask &= ~STS_PCD; writel(mask, &ehci->regs->intr_enable); readl(&ehci->regs->intr_enable); ehci->next_statechange = jiffies + msecs_to_jiffies(10); spin_unlock_irq (&ehci->lock); return 0; } /* caller has locked the root hub, and should reset/reinit on error */ static int ehci_bus_resume (struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); u32 temp; int i; if (time_before (jiffies, ehci->next_statechange)) msleep(5); spin_lock_irq (&ehci->lock); /* Ideally and we've got a real resume here, and no port's power * was lost. (For PCI, that means Vaux was maintained.) But we * could instead be restoring a swsusp snapshot -- so that BIOS was * the last user of the controller, not reset/pm hardware keeping * state we gave to it. */ temp = readl(&ehci->regs->intr_enable); ehci_dbg(ehci, "resume root hub%s\n", temp ? "" : " after power loss"); /* at least some APM implementations will try to deliver * IRQs right away, so delay them until we're ready. */ writel(0, &ehci->regs->intr_enable); /* re-init operational registers */ writel(0, &ehci->regs->segment); writel(ehci->periodic_dma, &ehci->regs->frame_list); writel((u32) ehci->async->qh_dma, &ehci->regs->async_next); /* restore CMD_RUN, framelist size, and irq threshold */ writel (ehci->command, &ehci->regs->command); /* manually resume the ports we suspended during bus_suspend() */ i = HCS_N_PORTS (ehci->hcs_params); while (i--) { temp = readl (&ehci->regs->port_status [i]); temp &= ~(PORT_RWC_BITS | PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E); if (test_bit(i, &ehci->bus_suspended) && (temp & PORT_SUSPEND)) { ehci->reset_done [i] = jiffies + msecs_to_jiffies (20); temp |= PORT_RESUME; } writel (temp, &ehci->regs->port_status [i]); } i = HCS_N_PORTS (ehci->hcs_params); mdelay (20); while (i--) { temp = readl (&ehci->regs->port_status [i]); if (test_bit(i, &ehci->bus_suspended) && (temp & PORT_SUSPEND)) { temp &= ~(PORT_RWC_BITS | PORT_RESUME); writel (temp, &ehci->regs->port_status [i]); ehci_vdbg (ehci, "resumed port %d\n", i + 1); } } (void) readl (&ehci->regs->command); /* maybe re-activate the schedule(s) */ temp = 0; if (ehci->async->qh_next.qh) temp |= CMD_ASE; if (ehci->periodic_sched) temp |= CMD_PSE; if (temp) { ehci->command |= temp; writel (ehci->command, &ehci->regs->command); } ehci->next_statechange = jiffies + msecs_to_jiffies(5); hcd->state = HC_STATE_RUNNING; /* Now we can safely re-enable irqs */ writel(INTR_MASK, &ehci->regs->intr_enable); spin_unlock_irq (&ehci->lock); return 0; } #else #define ehci_bus_suspend NULL #define ehci_bus_resume NULL #endif /* CONFIG_PM */ /*-------------------------------------------------------------------------*/ static int check_reset_complete ( struct ehci_hcd *ehci, int index, int port_status ) { if (!(port_status & PORT_CONNECT)) { ehci->reset_done [index] = 0; return port_status; } /* if reset finished and it's still not enabled -- handoff */ if (!(port_status & PORT_PE)) { /* with integrated TT, there's nobody to hand it to! */ if (ehci_is_TDI(ehci)) { ehci_dbg (ehci, "Failed to enable port %d on root hub TT\n", index+1); return port_status; } ehci_dbg (ehci, "port %d full speed --> companion\n", index + 1); // what happens if HCS_N_CC(params) == 0 ? port_status |= PORT_OWNER; port_status &= ~PORT_RWC_BITS; writel (port_status, &ehci->regs->port_status [index]); } else ehci_dbg (ehci, "port %d high speed\n", index + 1); return port_status; } /*-------------------------------------------------------------------------*/ /* build "status change" packet (one or two bytes) from HC registers */ static int ehci_hub_status_data (struct usb_hcd *hcd, char *buf) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); u32 temp, status = 0; u32 mask; int ports, i, retval = 1; unsigned long flags; /* if !USB_SUSPEND, root hub timers won't get shut down ... */ if (!HC_IS_RUNNING(hcd->state)) return 0; /* init status to no-changes */ buf [0] = 0; ports = HCS_N_PORTS (ehci->hcs_params); if (ports > 7) { buf [1] = 0; retval++; } /* Some boards (mostly VIA?) report bogus overcurrent indications, * causing massive log spam unless we completely ignore them. It * may be relevant that VIA VT8235 controlers, where PORT_POWER is * always set, seem to clear PORT_OCC and PORT_CSC when writing to * PORT_POWER; that's surprising, but maybe within-spec. */ if (!ignore_oc) mask = PORT_CSC | PORT_PEC | PORT_OCC; else mask = PORT_CSC | PORT_PEC; // PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND /* no hub change reports (bit 0) for now (power, ...) */ /* port N changes (bit N)? */ spin_lock_irqsave (&ehci->lock, flags); for (i = 0; i < ports; i++) { temp = readl (&ehci->regs->port_status [i]); if (temp & PORT_OWNER) { /* don't report this in GetPortStatus */ if (temp & PORT_CSC) { temp &= ~PORT_RWC_BITS; temp |= PORT_CSC; writel (temp, &ehci->regs->port_status [i]); } continue; } if (!(temp & PORT_CONNECT)) ehci->reset_done [i] = 0; if ((temp & mask) != 0 || ((temp & PORT_RESUME) != 0 && time_after (jiffies, ehci->reset_done [i]))) { if (i < 7) buf [0] |= 1 << (i + 1); else buf [1] |= 1 << (i - 7); status = STS_PCD; } } /* FIXME autosuspend idle root hubs */ spin_unlock_irqrestore (&ehci->lock, flags); return status ? retval : 0; } /*-------------------------------------------------------------------------*/ static void ehci_hub_descriptor ( struct ehci_hcd *ehci, struct usb_hub_descriptor *desc ) { int ports = HCS_N_PORTS (ehci->hcs_params); u16 temp; desc->bDescriptorType = 0x29; desc->bPwrOn2PwrGood = 10; /* ehci 1.0, 2.3.9 says 20ms max */ desc->bHubContrCurrent = 0; desc->bNbrPorts = ports; temp = 1 + (ports / 8); desc->bDescLength = 7 + 2 * temp; /* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */ memset (&desc->bitmap [0], 0, temp); memset (&desc->bitmap [temp], 0xff, temp); temp = 0x0008; /* per-port overcurrent reporting */ if (HCS_PPC (ehci->hcs_params)) temp |= 0x0001; /* per-port power control */ else temp |= 0x0002; /* no power switching */ #if 0 // re-enable when we support USB_PORT_FEAT_INDICATOR below. if (HCS_INDICATOR (ehci->hcs_params)) temp |= 0x0080; /* per-port indicators (LEDs) */ #endif desc->wHubCharacteristics = (__force __u16)cpu_to_le16 (temp); } /*-------------------------------------------------------------------------*/ #define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E) static int ehci_hub_control ( struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, char *buf, u16 wLength ) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); int ports = HCS_N_PORTS (ehci->hcs_params); u32 temp, status; unsigned long flags; int retval = 0; unsigned selector; /* * FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR. * HCS_INDICATOR may say we can change LEDs to off/amber/green. * (track current state ourselves) ... blink for diagnostics, * power, "this is the one", etc. EHCI spec supports this. */ spin_lock_irqsave (&ehci->lock, flags); switch (typeReq) { case ClearHubFeature: switch (wValue) { case C_HUB_LOCAL_POWER: case C_HUB_OVER_CURRENT: /* no hub-wide feature/status flags */ break; default: goto error; } break; case ClearPortFeature: if (!wIndex || wIndex > ports) goto error; wIndex--; temp = readl (&ehci->regs->port_status [wIndex]); if (temp & PORT_OWNER) break; switch (wValue) { case USB_PORT_FEAT_ENABLE: writel (temp & ~PORT_PE, &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_C_ENABLE: writel((temp & ~PORT_RWC_BITS) | PORT_PEC, &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_SUSPEND: if (temp & PORT_RESET) goto error; if (ehci->no_selective_suspend) break; if (temp & PORT_SUSPEND) { if ((temp & PORT_PE) == 0) goto error; /* resume signaling for 20 msec */ temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS); writel (temp | PORT_RESUME, &ehci->regs->port_status [wIndex]); ehci->reset_done [wIndex] = jiffies + msecs_to_jiffies (20); } break; case USB_PORT_FEAT_C_SUSPEND: /* we auto-clear this feature */ break; case USB_PORT_FEAT_POWER: if (HCS_PPC (ehci->hcs_params)) writel (temp & ~(PORT_RWC_BITS | PORT_POWER), &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_C_CONNECTION: writel((temp & ~PORT_RWC_BITS) | PORT_CSC, &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_C_OVER_CURRENT: writel((temp & ~PORT_RWC_BITS) | PORT_OCC, &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_C_RESET: /* GetPortStatus clears reset */ break; default: goto error; } readl (&ehci->regs->command); /* unblock posted write */ break; case GetHubDescriptor: ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *) buf); break; case GetHubStatus: /* no hub-wide feature/status flags */ memset (buf, 0, 4); //cpu_to_le32s ((u32 *) buf); break; case GetPortStatus: if (!wIndex || wIndex > ports) goto error; wIndex--; status = 0; temp = readl (&ehci->regs->port_status [wIndex]); // wPortChange bits if (temp & PORT_CSC) status |= 1 << USB_PORT_FEAT_C_CONNECTION; if (temp & PORT_PEC) status |= 1 << USB_PORT_FEAT_C_ENABLE; if ((temp & PORT_OCC) && !ignore_oc) status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT; /* whoever resumes must GetPortStatus to complete it!! */ if ((temp & PORT_RESUME) && time_after (jiffies, ehci->reset_done [wIndex])) { status |= 1 << USB_PORT_FEAT_C_SUSPEND; ehci->reset_done [wIndex] = 0; /* stop resume signaling */ temp = readl (&ehci->regs->port_status [wIndex]); writel (temp & ~(PORT_RWC_BITS | PORT_RESUME), &ehci->regs->port_status [wIndex]); retval = handshake ( &ehci->regs->port_status [wIndex], PORT_RESUME, 0, 2000 /* 2msec */); if (retval != 0) { ehci_err (ehci, "port %d resume error %d\n", wIndex + 1, retval); goto error; } temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10)); } /* whoever resets must GetPortStatus to complete it!! */ if ((temp & PORT_RESET) && time_after (jiffies, ehci->reset_done [wIndex])) { status |= 1 << USB_PORT_FEAT_C_RESET; ehci->reset_done [wIndex] = 0; /* force reset to complete */ writel (temp & ~(PORT_RWC_BITS | PORT_RESET), &ehci->regs->port_status [wIndex]); /* REVISIT: some hardware needs 550+ usec to clear * this bit; seems too long to spin routinely... */ retval = handshake ( &ehci->regs->port_status [wIndex], PORT_RESET, 0, 750); if (retval != 0) { ehci_err (ehci, "port %d reset error %d\n", wIndex + 1, retval); goto error; } /* see what we found out */ temp = check_reset_complete (ehci, wIndex, readl (&ehci->regs->port_status [wIndex])); } // don't show wPortStatus if it's owned by a companion hc if (!(temp & PORT_OWNER)) { if (temp & PORT_CONNECT) { status |= 1 << USB_PORT_FEAT_CONNECTION; // status may be from integrated TT status |= ehci_port_speed(ehci, temp); } if (temp & PORT_PE) status |= 1 << USB_PORT_FEAT_ENABLE; if (temp & (PORT_SUSPEND|PORT_RESUME)) status |= 1 << USB_PORT_FEAT_SUSPEND; if (temp & PORT_OC) status |= 1 << USB_PORT_FEAT_OVER_CURRENT; if (temp & PORT_RESET) status |= 1 << USB_PORT_FEAT_RESET; if (temp & PORT_POWER) status |= 1 << USB_PORT_FEAT_POWER; } #ifndef EHCI_VERBOSE_DEBUG if (status & ~0xffff) /* only if wPortChange is interesting */ #endif dbg_port (ehci, "GetStatus", wIndex + 1, temp); // we "know" this alignment is good, caller used kmalloc()... *((__le32 *) buf) = cpu_to_le32 (status); break; case SetHubFeature: switch (wValue) { case C_HUB_LOCAL_POWER: case C_HUB_OVER_CURRENT: /* no hub-wide feature/status flags */ break; default: goto error; } break; case SetPortFeature: selector = wIndex >> 8; wIndex &= 0xff; if (!wIndex || wIndex > ports) goto error; wIndex--; temp = readl (&ehci->regs->port_status [wIndex]); if (temp & PORT_OWNER) break; temp &= ~PORT_RWC_BITS; switch (wValue) { case USB_PORT_FEAT_SUSPEND: if (ehci->no_selective_suspend) break; if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) goto error; if (device_may_wakeup(&hcd->self.root_hub->dev)) temp |= PORT_WAKE_BITS; writel (temp | PORT_SUSPEND, &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_POWER: if (HCS_PPC (ehci->hcs_params)) writel (temp | PORT_POWER, &ehci->regs->port_status [wIndex]); break; case USB_PORT_FEAT_RESET: if (temp & PORT_RESUME) goto error; /* line status bits may report this as low speed, * which can be fine if this root hub has a * transaction translator built in. */ if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT && !ehci_is_TDI(ehci) && PORT_USB11 (temp)) { ehci_dbg (ehci, "port %d low speed --> companion\n", wIndex + 1); temp |= PORT_OWNER; } else { ehci_vdbg (ehci, "port %d reset\n", wIndex + 1); temp |= PORT_RESET; temp &= ~PORT_PE; /* * caller must wait, then call GetPortStatus * usb 2.0 spec says 50 ms resets on root */ ehci->reset_done [wIndex] = jiffies + msecs_to_jiffies (50); } writel (temp, &ehci->regs->port_status [wIndex]); break; /* For downstream facing ports (these): one hub port is put * into test mode according to USB2 11.24.2.13, then the hub * must be reset (which for root hub now means rmmod+modprobe, * or else system reboot). See EHCI 2.3.9 and 4.14 for info * about the EHCI-specific stuff. */ case USB_PORT_FEAT_TEST: if (!selector || selector > 5) goto error; ehci_quiesce(ehci); ehci_halt(ehci); temp |= selector << 16; writel (temp, &ehci->regs->port_status [wIndex]); break; default: goto error; } readl (&ehci->regs->command); /* unblock posted writes */ break; default: error: /* "stall" on error */ retval = -EPIPE; } spin_unlock_irqrestore (&ehci->lock, flags); return retval; }