+
+static struct fb_videomode __initdata ltv350qv_modes[] = {
+ {
+ .name = "320x240 @ 75",
+ .refresh = 75,
+ .xres = 320, .yres = 240,
+ .pixclock = KHZ2PICOS(6891),
+
+ .left_margin = 17, .right_margin = 33,
+ .upper_margin = 10, .lower_margin = 10,
+ .hsync_len = 16, .vsync_len = 1,
+
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs __initdata atstk1000_default_monspecs = {
+ .manufacturer = "SNG",
+ .monitor = "LTV350QV",
+ .modedb = ltv350qv_modes,
+ .modedb_len = ARRAY_SIZE(ltv350qv_modes),
+ .hfmin = 14820,
+ .hfmax = 22230,
+ .vfmin = 60,
+ .vfmax = 90,
+ .dclkmax = 30000000,
+};
+
+struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
+ .default_bpp = 24,
+ .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
+ .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
+ | ATMEL_LCDC_INVCLK
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
+ | ATMEL_LCDC_MEMOR_BIG),
+ .default_monspecs = &atstk1000_default_monspecs,
+ .guard_time = 2,
+};
+
+#ifdef CONFIG_BOARD_ATSTK1000_J2_LED
+#include <linux/leds.h>
+
+static struct gpio_led stk1000_j2_led[] = {
+#ifdef CONFIG_BOARD_ATSTK1000_J2_LED8
+#define LEDSTRING "J2 jumpered to LED8"
+ { .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
+ { .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
+ { .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
+ { .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
+ { .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
+ { .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
+ { .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
+ { .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
+ .default_trigger = "heartbeat", },
+#else /* RGB */
+#define LEDSTRING "J2 jumpered to RGB LEDs"
+ { .name = "r1:red", .gpio = GPIO_PIN_PB( 8), },
+ { .name = "g1:green", .gpio = GPIO_PIN_PB(10), },
+ { .name = "b1:blue", .gpio = GPIO_PIN_PB(14), },
+
+ { .name = "r2:red", .gpio = GPIO_PIN_PB( 9),
+ .default_trigger = "heartbeat", },
+ { .name = "g2:green", .gpio = GPIO_PIN_PB(13), },
+ { .name = "b2:blue", .gpio = GPIO_PIN_PB(15),
+ .default_trigger = "heartbeat", },
+ /* PB16, PB30 unused */
+#endif
+};
+
+static struct gpio_led_platform_data stk1000_j2_led_data = {
+ .num_leds = ARRAY_SIZE(stk1000_j2_led),
+ .leds = stk1000_j2_led,
+};
+
+static struct platform_device stk1000_j2_led_dev = {
+ .name = "leds-gpio",
+ .id = 2, /* gpio block J2 */
+ .dev = {
+ .platform_data = &stk1000_j2_led_data,
+ },
+};
+
+void __init atstk1000_setup_j2_leds(void)
+{
+ unsigned i;
+
+ for (i = 0; i < ARRAY_SIZE(stk1000_j2_led); i++)
+ at32_select_gpio(stk1000_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
+
+ printk("STK1000: " LEDSTRING "\n");
+ platform_device_register(&stk1000_j2_led_dev);
+}
+#else /* CONFIG_BOARD_ATSTK1000_J2_LED */
+void __init atstk1000_setup_j2_leds(void)
+{
+
+}
+#endif /* CONFIG_BOARD_ATSTK1000_J2_LED */