=======================
Supported chips:
- * Abit uGuru (Hardware Monitor part only)
+ * Abit uGuru revision 1 & 2 (Hardware Monitor part only)
Prefix: 'abituguru'
Addresses scanned: ISA 0x0E0
Datasheet: Not available, this driver is based on reverse engineering.
A "Datasheet" has been written based on the reverse engineering it
should be available in the same dir as this file under the name
abituguru-datasheet.
+ Note:
+ The uGuru is a microcontroller with onboard firmware which programs
+ it to behave as a hwmon IC. There are many different revisions of the
+ firmware and thus effectivly many different revisions of the uGuru.
+ Below is an incomplete list with which revisions are used for which
+ Motherboards:
+ uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) (1)
+ uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO)
+ uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
+ uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty)
+ uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
+ uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X,
+ AW9D-MAX) (2)
+ 1) For revisions 2 and 3 uGuru's the driver can autodetect the
+ sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
+ this doesnot always work. For these uGuru's the autodection can
+ be overriden with the bank1_types module param. For all 3 known
+ revison 1 motherboards the correct use of this param is:
+ bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
+ You may also need to specify the fan_sensors option for these boards
+ fan_sensors=5
+ 2) There is a seperate abituguru3 driver for these motherboards,
+ the abituguru (without the 3 !) driver will not work on these
+ motherboards (and visa versa)!
Authors:
Hans de Goede <j.w.r.degoede@hhs.nl>,
-----------------
* force: bool Force detection. Note this parameter only causes the
- detection to be skipped, if the uGuru can't be read
- the module initialization (insmod) will still fail.
+ detection to be skipped, and thus the insmod to
+ succeed. If the uGuru can't be read the actual hwmon
+ driver will not load and thus no hwmon device will get
+ registered.
+* bank1_types: int[] Bank1 sensortype autodetection override:
+ -1 autodetect (default)
+ 0 volt sensor
+ 1 temp sensor
+ 2 not connected
* fan_sensors: int Tell the driver how many fan speed sensors there are
on your motherboard. Default: 0 (autodetect).
* pwms: int Tell the driver how many fan speed controls (fan
* verbose: int How verbose should the driver be? (0-3):
0 normal output
1 + verbose error reporting
- 2 + sensors type probing info\n"
+ 2 + sensors type probing info (default)
3 + retryable error reporting
Default: 2 (the driver is still in the testing phase)
Description
-----------
-This driver supports the hardware monitoring features of the Abit uGuru chip
-found on Abit uGuru featuring motherboards (most modern Abit motherboards).
+This driver supports the hardware monitoring features of the first and
+second revision of the Abit uGuru chip found on Abit uGuru featuring
+motherboards (most modern Abit motherboards).
-The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit
-claiming it is "a new microprocessor designed by the ABIT Engineers").
-Unfortunatly this doesn't help since the W83L950D is a generic
-microcontroller with a custom Abit application running on it.
+The first and second revision of the uGuru chip in reality is a Winbond
+W83L950D in disguise (despite Abit claiming it is "a new microprocessor
+designed by the ABIT Engineers"). Unfortunatly this doesn't help since the
+W83L950D is a generic microcontroller with a custom Abit application running
+on it.
Despite Abit not releasing any information regarding the uGuru, Olle
Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part