FB The frame buffer device is enabled.
HW Appropriate hardware is enabled.
IA-64 IA-64 architecture is enabled.
+ IMA Integrity measurement architecture is enabled.
IOSCHED More than one I/O scheduler is enabled.
IP_PNP IP DHCP, BOOTP, or RARP is enabled.
ISAPNP ISA PnP code is enabled.
Parameters denoted with BOOT are actually interpreted by the boot
loader, and have no meaning to the kernel directly.
Do not modify the syntax of boot loader parameters without extreme
-need or coordination with <Documentation/x86/i386/boot.txt>.
+need or coordination with <Documentation/x86/boot.txt>.
There are also arch-specific kernel-parameters not documented here.
See for example <Documentation/x86/x86_64/boot-options.txt>.
Range: 0 - 8192
Default: 64
+ dma_debug=off If the kernel is compiled with DMA_API_DEBUG support
+ this option disables the debugging code at boot.
+
+ dma_debug_entries=<number>
+ This option allows to tune the number of preallocated
+ entries for DMA-API debugging code. One entry is
+ required per DMA-API allocation. Use this if the
+ DMA-API debugging code disables itself because the
+ architectural default is too low.
+
hpet= [X86-32,HPET] option to control HPET usage
- Format: { enable (default) | disable | force }
+ Format: { enable (default) | disable | force |
+ verbose }
disable: disable HPET and use PIT instead
force: allow force enabled of undocumented chips (ICH4,
VIA, nVidia)
+ verbose: show contents of HPET registers during setup
com20020= [HW,NET] ARCnet - COM20020 chipset
Format:
hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
terminal devices. Valid values: 0..8
+ hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
+ If specified, z/VM IUCV HVC accepts connections
+ from listed z/VM user IDs only.
i8042.debug [HW] Toggle i8042 debug mode
i8042.direct [HW] Put keyboard port into non-translated mode
ihash_entries= [KNL]
Set number of hash buckets for inode cache.
+ ima_audit= [IMA]
+ Format: { "0" | "1" }
+ 0 -- integrity auditing messages. (Default)
+ 1 -- enable informational integrity auditing messages.
+
+ ima_hash= [IMA]
+ Formt: { "sha1" | "md5" }
+ default: "sha1"
+
in2000= [HW,SCSI]
See header of drivers/scsi/in2000.c.
memtest= [KNL,X86] Enable memtest
Format: <integer>
- range: 0,4 : pattern number
default : 0 <disable>
+ Specifies the number of memtest passes to be
+ performed. Each pass selects another test
+ pattern from a given set of patterns. Memtest
+ fills the memory with this pattern, validates
+ memory contents and reserves bad memory
+ regions that are detected.
meye.*= [HW] Set MotionEye Camera parameters
See Documentation/video4linux/meye.txt.
autoconfiguration.
Ranges are in pairs (memory base and size).
- dynamic_printk Enables pr_debug()/dev_dbg() calls if
- CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
- These can also be switched on/off via
- <debugfs>/dynamic_printk/modules
-
print-fatal-signals=
[KNL] debug: print fatal signals
print-fatal-signals=1: print segfault info to
See Documentation/fb/modedb.txt.
vga= [BOOT,X86-32] Select a particular video mode
- See Documentation/x86/i386/boot.txt and
+ See Documentation/x86/boot.txt and
Documentation/svga.txt.
Use vga=ask for menu.
This is actually a boot loader parameter; the value is