Fix timerfd breakage on avr32

[linux-2.6-omap-h63xx.git] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 5d171b7b8393b95c857f9aad5945939a2c999e21..9ad4e6fc56fdb7a880e5276ea5f9b0c1d780778e 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -168,6 +168,11 @@ and is between 256 and 4096 characters. It is defined in the file
        acpi_irq_isa=   [HW,ACPI] If irq_balance, mark listed IRQs used by ISA
                        Format: <irq>,<irq>...
 
+       acpi_new_pts_ordering [HW,ACPI]
+                       Enforce the ACPI 2.0 ordering of the _PTS control
+                       method wrt putting devices into low power states
+                       default: pre ACPI 2.0 ordering of _PTS
+
        acpi_no_auto_ssdt       [HW,ACPI] Disable automatic loading of SSDT
 
        acpi_os_name=   [HW,ACPI] Tell ACPI BIOS the name of the OS
@@ -544,7 +549,7 @@ and is between 256 and 4096 characters. It is defined in the file
                        1 will print _a lot_ more information - normally
                        only useful to kernel developers.
 
-       decnet=         [HW,NET]
+       decnet.addr=    [HW,NET]
                        Format: <area>[,<node>]
                        See also Documentation/networking/decnet.txt.
 
@@ -717,6 +722,7 @@ and is between 256 and 4096 characters. It is defined in the file
                        See Documentation/isdn/README.HiSax.
 
        hugepages=      [HW,X86-32,IA-64] Maximal number of HugeTLB pages.
+       hugepagesz=     [HW,IA-64,PPC] The size of the HugeTLB pages.
 
        i8042.direct    [HW] Put keyboard port into non-translated mode
        i8042.dumbkbd   [HW] Pretend that controller can only read data from
@@ -1555,14 +1561,17 @@ and is between 256 and 4096 characters. It is defined in the file
        ramdisk_size=   [RAM] Sizes of RAM disks in kilobytes
                        See Documentation/ramdisk.txt.
 
-       rcu.blimit=     [KNL,BOOT] Set maximum number of finished
-                       RCU callbacks to process in one batch.
+       rcupdate.blimit=        [KNL,BOOT]
+                       Set maximum number of finished RCU callbacks to process
+                       in one batch.
 
-       rcu.qhimark=    [KNL,BOOT] Set threshold of queued
+       rcupdate.qhimark=       [KNL,BOOT]
+                       Set threshold of queued
                        RCU callbacks over which batch limiting is disabled.
 
-       rcu.qlowmark=   [KNL,BOOT] Set threshold of queued
-                       RCU callbacks below which batch limiting is re-enabled.
+       rcupdate.qlowmark=      [KNL,BOOT]
+                       Set threshold of queued RCU callbacks below which
+                       batch limiting is re-enabled.
 
        rdinit=         [KNL]
                        Format: <full_path>
@@ -1882,9 +1891,6 @@ and is between 256 and 4096 characters. It is defined in the file
        st=             [HW,SCSI] SCSI tape parameters (buffers, etc.)
                        See Documentation/scsi/st.txt.
 
-       st0x=           [HW,SCSI]
-                       See header of drivers/scsi/seagate.c.
-
        sti=            [PARISC,HW]
                        Format: <num>
                        Set the STI (builtin display/keyboard on the HP-PARISC
@@ -1969,9 +1975,6 @@ and is between 256 and 4096 characters. It is defined in the file
        tipar.delay=    [HW,PPT]
                        Set inter-bit delay in microseconds (default 10).
 
-       tmc8xx=         [HW,SCSI]
-                       See header of drivers/scsi/seagate.c.
-
        tmscsim=        [HW,SCSI]
                        See comment before function dc390_setup() in
                        drivers/scsi/tmscsim.c.