GENERIC_TIME The generic timeofday code is enabled.
NFS Appropriate NFS support is enabled.
OSS OSS sound support is enabled.
+ PV_OPS A paravirtualized kernel
PARIDE The ParIDE subsystem is enabled.
PARISC The PA-RISC architecture is enabled.
PCI PCI bus support is enabled.
clocksource is not available, it defaults to PIT.
Format: { pit | tsc | cyclone | pmtmr }
+ clocksource= [GENERIC_TIME] Override the default clocksource
+ Format: <string>
+ Override the default clocksource and use the clocksource
+ with the name specified.
+ Some clocksource names to choose from, depending on
+ the platform:
+ [all] jiffies (this is the base, fallback clocksource)
+ [ACPI] acpi_pm
+ [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2,
+ pxa_timer,timer3,32k_counter,timer0_1
+ [AVR32] avr32
+ [IA-32] pit,hpet,tsc,vmi-timer;
+ scx200_hrt on Geode; cyclone on IBM x440
+ [MIPS] MIPS
+ [PARISC] cr16
+ [S390] tod
+ [SH] SuperH
+ [SPARC64] tick
+ [X86-64] hpet,tsc
+
code_bytes [IA32] How many bytes of object code to print in an
oops report.
Range: 0 - 8192
Format: <area>[,<node>]
See also Documentation/networking/decnet.txt.
+ default_blu= [VT]
+ Format: <blue0>,<blue1>,<blue2>,...,<blue15>
+ Change the default blue palette of the console.
+ This is a 16-member array composed of values
+ ranging from 0-255.
+
+ default_grn= [VT]
+ Format: <green0>,<green1>,<green2>,...,<green15>
+ Change the default green palette of the console.
+ This is a 16-member array composed of values
+ ranging from 0-255.
+
+ default_red= [VT]
+ Format: <red0>,<red1>,<red2>,...,<red15>
+ Change the default red palette of the console.
+ This is a 16-member array composed of values
+ ranging from 0-255.
+
+ default_utf8= [VT]
+ Format=<0|1>
+ Set system-wide default UTF-8 mode for all tty's.
+ Default is 0 and by setting to 1, it enables UTF-8
+ mode for all newly opened or allocated terminals.
+
dhash_entries= [KNL]
Set number of hash buckets for dentry cache.
idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
See Documentation/ide.txt.
- idle= [HW]
- Format: idle=poll or idle=halt
+ idle= [X86]
+ Format: idle=poll or idle=mwait
+ Poll forces a polling idle loop that can slightly improves the performance
+ of waking up a idle CPU, but will use a lot of power and make the system
+ run hot. Not recommended.
+ idle=mwait. On systems which support MONITOR/MWAIT but the kernel chose
+ to not use it because it doesn't save as much power as a normal idle
+ loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same
+ as idle=poll.
ignore_loglevel [KNL]
Ignore loglevel setting - this will print /all/
inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
Format: <irq>
- combined_mode= [HW] control which driver uses IDE ports in combined
- mode: legacy IDE driver, libata, or both
- (in the libata case, libata.atapi_enabled=1 may be
- useful as well). Note that using the ide or libata
- options may affect your device naming (e.g. by
- changing hdc to sdb).
- Format: combined (default), ide, or libata
-
inttest= [IA64]
io7= [HW] IO7 for Marvel based alpha systems
lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip
Format: addr:<io>,irq:<irq>
+ legacy_serial.force [HW,IA-32,X86-64]
+ Probe for COM ports at legacy addresses even
+ if PNPBIOS or ACPI should describe them. This
+ is for working around firmware defects.
+
llsc*= [IA64] See function print_params() in
arch/ia64/sn/kernel/llsc4.c.
nomce [IA-32] Machine Check Exception
+ noreplace-paravirt [IA-32,PV_OPS] Don't patch paravirt_ops
+
+ noreplace-smp [IA-32,SMP] Don't replace SMP instructions
+ with UP alternatives
+
noresidual [PPC] Don't use residual data on PReP machines.
noresume [SWSUSP] Disables resume and restores original swap
smart2= [HW]
Format: <io1>[,<io2>[,...,<io8>]]
+ smp-alt-once [IA-32,SMP] On a hotplug CPU system, only
+ attempt to substitute SMP alternatives once at boot.
+
+ smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
+ smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
+ smsc-ircc2.ircc_sir= [HW] SIR base I/O port
+ smsc-ircc2.ircc_fir= [HW] FIR base I/O port
+ smsc-ircc2.ircc_irq= [HW] IRQ line
+ smsc-ircc2.ircc_dma= [HW] DMA channel
+ smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
+ 0: Toshiba Satellite 1800 (GP data pin select)
+ 1: Fast pin select (default)
+ 2: ATC IRMode
+
snd-ad1816a= [HW,ALSA]
snd-ad1848= [HW,ALSA]
time Show timing data prefixed to each printk message line
- clocksource= [GENERIC_TIME] Override the default clocksource
- Override the default clocksource and use the clocksource
- with the name specified.
-
tipar.timeout= [HW,PPT]
Set communications timeout in tenths of a second
(default 15).
[USBHID] The interval which mice are to be polled at.
vdso= [IA-32,SH]
+ vdso=2: enable compat VDSO (default with COMPAT_VDSO)
vdso=1: enable VDSO (default)
vdso=0: disable VDSO mapping