fb: push down the BKL in the ioctl handler

[linux-2.6-omap-h63xx.git] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 25efbaf1f59bc23ef21cdd3d50731509e06fbeef..d4f4875fc7c6d2e463e9c2b6e26d2d278cf1399c 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -658,11 +658,12 @@ and is between 256 and 4096 characters. It is defined in the file
        earlyprintk=    [X86-32,X86-64,SH,BLACKFIN]
                        earlyprintk=vga
                        earlyprintk=serial[,ttySn[,baudrate]]
+                       earlyprintk=dbgp
 
                        Append ",keep" to not disable it when the real console
                        takes over.
 
-                       Only vga or serial at a time, not both.
+                       Only vga or serial or usb debug port at a time.
 
                        Currently only ttyS0 and ttyS1 are supported.
 
@@ -795,6 +796,7 @@ and is between 256 and 4096 characters. It is defined in the file
                        Defaults to the default architecture's huge page size
                        if not specified.
 
+       i8042.debug     [HW] Toggle i8042 debug mode
        i8042.direct    [HW] Put keyboard port into non-translated mode
        i8042.dumbkbd   [HW] Pretend that controller can only read data from
                             keyboard and cannot control its state
@@ -1231,6 +1233,29 @@ and is between 256 and 4096 characters. It is defined in the file
                                 or
                                 memmap=0x10000$0x18690000
 
+       memory_corruption_check=0/1 [X86]
+                       Some BIOSes seem to corrupt the first 64k of
+                       memory when doing things like suspend/resume.
+                       Setting this option will scan the memory
+                       looking for corruption.  Enabling this will
+                       both detect corruption and prevent the kernel
+                       from using the memory being corrupted.
+                       However, its intended as a diagnostic tool; if
+                       repeatable BIOS-originated corruption always
+                       affects the same memory, you can use memmap=
+                       to prevent the kernel from using that memory.
+
+       memory_corruption_check_size=size [X86]
+                       By default it checks for corruption in the low
+                       64k, making this memory unavailable for normal
+                       use.  Use this parameter to scan for
+                       corruption in more or less memory.
+
+       memory_corruption_check_period=seconds [X86]
+                       By default it checks for corruption every 60
+                       seconds.  Use this parameter to check at some
+                       other rate.  0 disables periodic checking.
+
        memtest=        [KNL,X86] Enable memtest
                        Format: <integer>
                        range: 0,4 : pattern number
@@ -1689,6 +1714,11 @@ and is between 256 and 4096 characters. It is defined in the file
                        autoconfiguration.
                        Ranges are in pairs (memory base and size).
 
+       dynamic_printk
+                       Enables pr_debug()/dev_dbg() calls if
+                       CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
+                       be switched on/off via <debugfs>/dynamic_printk/modules
+
        print-fatal-signals=
                        [KNL] debug: print fatal signals
                        print-fatal-signals=1: print segfault info to
@@ -2223,6 +2253,25 @@ and is between 256 and 4096 characters. It is defined in the file
                        autosuspended.  Devices for which the delay is set
                        to a negative value won't be autosuspended at all.
 
+       usbcore.usbfs_snoop=
+                       [USB] Set to log all usbfs traffic (default 0 = off).
+
+       usbcore.blinkenlights=
+                       [USB] Set to cycle leds on hubs (default 0 = off).
+
+       usbcore.old_scheme_first=
+                       [USB] Start with the old device initialization
+                       scheme (default 0 = off).
+
+       usbcore.use_both_schemes=
+                       [USB] Try the other device initialization scheme
+                       if the first one fails (default 1 = enabled).
+
+       usbcore.initial_descriptor_timeout=
+                       [USB] Specifies timeout for the initial 64-byte
+                        USB_REQ_GET_DESCRIPTOR request in milliseconds
+                       (default 5000 = 5.0 seconds).
+
        usbhid.mousepoll=
                        [USBHID] The interval which mice are to be polled at.